SLRS

MASON INDUSTRIES, Inc. 1”(25mm) and Page 2, 2”(51mm) TYPE

Manufacturers of Vibration Control Products
DEFLECTION RESTRAINED
350 Rabro Drive 2101 W. Crescent Ave., Suite D
Hauppauge, NY 11788 Anaheim, CA 92801 SEISMIC SPRING MOUNTS
631/348-0282 714/535-2727
FAX 631/348-0279 FAX 714/535-5738 with or without EXTENDED
[email protected] [email protected]
www.Mason-Ind.com www.MasonAnaheim.com BASE PLATES DATA SHEET DS-224

1”(25mm) Deflection SLRS SPRING MOUNTS SLRSEBP E E

E
EMBD-
Max. Bolt
Use SLRSEBP when Extended Base Plate is required. E Diameter
4 Holes-
SLRS APPROVED
California Office of Statewide
Sizes B,
1, 2 & 4
"D" Tap - 4 Holes unless Health Planning and Development 6 Holes-
Vertical Limit otherwise requested FIXED EQUIPMENT ANCHORAGE
Sizes
Stops-Out of E OPA-0194 January 6, 2003
6&9
contact during E *Valid for 3 Years Maximum

E H Plug
normal operation E Bill Staehlin (916) 654-3362 Weld
Lower T
Restraining Adjustment F
Nut Bolt L
C
EH EH
Inspection CW
Neoprene EW F EL
Ports
All Directional
Snubber
Grommet *with Red inner spring
TYPE SLRS & SLRSEBP RATINGS **with Green inner spring
T
H SLRS or Rated Rated Mount Max.
SLRSEBP Capacity Defl Constant G Spring
Size (Ibs) (kg) (in) (mm) (Ibs/in)(kg/mm) Rating Color
HCL
HCW B-65 65 29 2.10 53 31 0.55 24.6 Brown
W L Drain B-85 85 39 2.10 53 40 0.74 18.9 White††
B-115 115 52 2.00 51 57 1.02 13.9 Silver
Holes B-150 150 68 2.00 51 75 1.33 10.6 Orange
One Piece
B-280 280 127 1.60 41 174 3.10 5.7 Green
Steel Housing Internal B-450 450 204 1.31 33 344 6.18 3.5 Red
Neoprene Non-Skid Neoprene Pad- B-750 750 340 1.12 28 670 12.14 2.1 White
Acoustical Pad can be removed if B-1000 1000 454 1.00 25 1000 18.16 1.6 Blue
Rubber Snubbing Pad mounts are welded
in position. 1-1000 1000 454 1.00 25 1000 18.16 6.0 Black
material molded 1-1350 1350 612 1.00 25 1350 24.48 4.4 Yellow
onto Spring Holder MBD -Max 1-1750 1750 794 1.00 25 1750 31.76 3.4 Black*
Bolt Diameter 1-2100 2100 953 1.00 25 2100 38.12 2.8 Yellow
Illustration above shows a SLRS-4 (4 springs). SLRS-B & -1 have 1-2385 2385 1082 1.00 25 2385 43.28 2.5 Yellow**
one spring, and SLRS-2 has two springs, SLRS-6 has six springs 1-2650 2650 1202 1.00 25 2650 48.08 2.3 Red*
and SLRS-9 has nine springs. 1-2935 2935 1331 1.00 25 2935 53.24 2.0 Red**
2-3500 3500 1588 1.00 25 3500 63.52 1.5 Black*
OSHPD OPA-194 2-4200 4200 1905 1.00 25 4200 76.20 1.2 Yellow*
Rated Load Curves (lbs kg) Horizontal, Vertical and 2-4770 4770 2164 1.00 25 4770 86.56 1.1 Yellow**
45° plotted Ratings are California
14928 6785 OSHPD approved values having the 4-5400 5400 2449 1.00 25 5400 97.96 2.0 Yellow
SLRS-4 14511 4-7000 7000 3175 1.00 25 7000 127.00 1.6 Black*
6596 OSHPD Anchorage Preapproval
Number OPA-0194. Testing and 4-8400 8400 3810 1.00 25 8400 152.40 1.3 Yellow*
calculations were performed to meet 4-9540 9540 4327 1.00 25 9540 173.08 1.2 Yellow**
is
Ax

OSHPD criteria. 4-10600 10600 4808 1.00 25 10600 192.32 1.1 Red*
45 O

V 8785 3993
E
R 4-11740 11740 5325 1.00 25 11740 213.00 0.9 Red**
T To use approved OSHPD rated
I 5955 load curves: 6-12600 12600 5715 1.00 25 12600 228.60 1.5 Yellow*
C 2701 6-14310 14310 6491 1.00 25 14310 259.64 1.4 Yellow**
A
L
5809 2641 1) Calculate Vertical and Horizontal 6-15900 15900 7212 1.00 25 15900 288.48 1.2 Red*
5023
2283 Forces on mountings including 6-17610 17610 7988 1.00 25 17610 319.52 1.1 Red**
SLRS-1 translations and overturning
moments. 9-18900 18900 8573 1.00 25 18900 342.92 1.4 Yellow*
SLRS-2 9-21465 21465 9736 1.00 25 21465 389.44 1.2 Yellow**
2) Plot Horizontal and Vertical Loads.
HORIZONTAL
5195 6570 11028 The intersection must fall within the 9-23850 23850 10818 1.00 25 23850 432.72 1.1 Red*
2361 2987 5013
area below the OSHPD curve.
SPRING CHARACTERISTICS (inches and mm)
TYPE SLRS & SLRSEBP DIMENSIONS (inches and mm) Spring Free Ratio Ratio
SLRS SLRSEBP Size OD Height Kx/Ky OD/OH
Size H T D E L HCL W HCW MBD EL EHCL F EW EHCW EMBD B 23/8 60 40/0 102 0.70-0.80 0.80
81/2 3/8 1/2 11/8 81/2 7 41/4 23/4 5/8 10 8 - 9 71/4 3/4 C 27/8 73 41/8 105 0.90-1.10 0.92
B 216 10 13 29 216 178 108 70 16 254 203 - 229 184 19 All springs have an additional travel to solid
1 81/2 3/8 5/8 13/8 91/2 71/2 51/4 31/2 5/8 10 8 - 9 71/4 3/4 equal to 50% of the rated deflection.
216 10 16 35 241 191 133 89 16 254 203 - 229 184 19
Solid Spring Height = Free Height minus 1.5
2 81/2 3/8 5/8 13/8 14 121/4 51/4 31/2 5/8 14 12 - 11 9 7/8
times the Rated Deflection.
216 10 16 35 356 311 133 89 16 356 305 - 295 229 22
81/2 3/8 7/8 13/8 13 11 83/8 61/4 3/4 17 15 - 14 12 11/8 Designs using these mounts to resist wind
4 216 10 22 35 330 279 213 159 19 432 381 - 356 305 29
loads must be in accordance with ASCE 7-02.
9 1/2 1 15/8 161/2 14 83/8 6 1 27 - 12 15 12 11/8
6 Housing load ratings expressed in G’s are
229 13 25 41 419 356 213 152 25 686 - 305 381 305 29
based on tests with bolted connections to
9 93/4 5/8 1 2 17 143/4 13 103/4 1 27 - 12 18 1
15 1 /8 steel top and bottom. SLRS housings require
248 16 25 51 432 375 330 273 25 686 - 305 457 381 29 uniform support under entire base plate.
SLRS DATA SHEET DS-224 MASON INDUSTRIES

2”(51mm) Deflection SLRS SPRING MOUNTS SLRSEBP E E

E EMBD- Max.
Use SLRSEBP when Extended Base Plate is required. E
Bolt Diameter
4 Holes-

SLRS
Sizes
APPROVED B, B2, C2,
California Office of Statewide 2&4
"D" Tap - 4 Holes unless Health Planning and Development
FIXED EQUIPMENT ANCHORAGE 6 Holes-
Vertical Limit otherwise requested OPA-0194 January 6, 2003 Sizes 6 & 9
Stops-Out of E *Valid for 3 Years Maximum

contact during E H Plug

E Weld
normal operation E Bill Staehlin (916) 654-3362

T
Lower
Restraining F
Adjustment L
Nut Bolt HC
EH E
CW
Inspection EW F EL
Neoprene Ports
All Directional
Snubber
Grommet TYPE SLRS & SLRSEBP RATINGS *with Red inner spring
T SLRS or Rated Rated Mount Max.
H SLRSEBP Capacity Defl Constant G Spring
Size (Ibs) (kg) (in) (mm) (Ibs/in)(kg/mm) Rating Color
HCL B-20 20 9 2.40 61 8 0.15 80.0 Tan
HCW
B-26 26 12 2.18 55 12 0.22 61.5 Wht/Blue
W L Drain B-35 35 16 2.20 56 16 0.29 45.7 Purple
Holes B-50 50 23 2.20 56 24 0.41 32.0 Wht/Red
One Piece B-65 65 29 2.10 53 31 0.55 24.6 Brown
Steel Housing Internal B-85 85 39 2.10 53 40 0.74 18.8 Wht/Blk
Neoprene Non-Skid Neoprene Pad- B-115 115 52 2.00 51 57 1.02 13.9 Silver
Acoustical Pad can be removed if B-150 150 68 2.00 51 75 1.33 10.7 Orange
Rubber Snubbing Pad mounts are welded B2-210 210 95 2.12 54 99 1.76 7.6 Silver
material molded in position. B2-290 290 132 2.00 51 144 2.59 5.5 Blue
B2-450 †
450 204 2.00 51 224 4.00 3.6 Tan
onto Spring Holder MBD -Max B2-680 †
680 308 2.00 51 340 6.04 2.4 Gray
Bolt Diameter
C2-125 125 57 2.50 64 50 0.89 48.0 Purple
Illustration above shows a SLRS-4-C2 (4 springs). SLRS-B, C2-170 170 77 2.40 61 70 1.26 35.0 Brown
-2 & -C2 have one spring, and SLRS-2-C2 has two springs, C2-210 210 95 2.30 58 90 1.64 28.3 Red
SLRS-6-C2 has six springs and SLRS-9-C2 has nine springs. C2-260 260 118 2.20 56 120 2.11 23.0 White
C2-330 330 150 2.00 51 165 2.94 18.0 Black
See front page for OSHPD Rated Load Curves C2-460 460 209 2.00 51 230 4.10 13.0 Blue
C2-610 610 277 2.00 51 305 5.43 9.8 Green
SPRING CHARACTERISTICS (inches and mm) C2-880 †
880 399 2.00 51 440 7.82 6.8 Gray
C2-1210 †
1210 549 2.00 51 605 10.76 4.9 Silver
Spring Free Ratio Ratio C2-1540† 1540 699 2.00 51 770 13.71 3.9 Gray*
Size OD Height Kx/Ky OD/OH C2-1870 †
1870 848 2.00 51 935 16.63 3.2 Silver*
B 23/8 60 40/0 102 0.55-0.65 0.95-1.00 2-C2-340 340 154 2.40 61 140 2.52 15.3 Brown
B2 23/8 60 41/2 114 0.80-0.90 1.19-1.48 2-C2-420 420 191 2.30 58 180 3.29 12.4 Red
C2 27/8 73 50/0 127 0.63-0.85 0.96-1.15 2-C2-520 520 236 2.20 56 240 4.21 10.0 White
2-C2-660 660 299 2.00 51 330 5.86 7.9 Black
†
Published ratings allow minimum 25% additional travel to solid. 2-C2-920 920 417 2.00 51 460 8.18 5.7 Blue
For a full 50% specified minimum use the following ratings: 2-C2-1220 1220 553 2.00 51 610 10.84 4.3 Green
Derated Derated 2-C2-1760† 1760 798 2.00 51 880 15.65 3.0 Gray
Capacity Defl. Capacity Defl. 2-C2-2420 †
2420 1098 2.00 51 1210 21.53 2.2 Silver
Size (Ibs) (kg) (in)(mm) Size (Ibs) (kg) (in)(mm) 2-C2-3080† 3080 1397 2.00 51 1540 27.39 1.7 Gray*
2-C2-3740† 3740 1696 2.00 51 1870 33.24 1.4 Silver*
B2-450 410 186 1.83 46 2-C2-3740 3120 1415 1.67 42 4-C2-4840† 4840 2195 2.00 51 2420 43.04 2.3 Silver
B2-680 565 256 1.67 42 4-C2-4840 4040 1833 1.67 42 4-C2-6160† 6160 2794 2.00 51 3080 54.78 1.8 Gray*
C2-880 800 363 1.82 46 4-C2-6160 5145 2334 1.67 42 4-C2 7480 †
7480 3393 2.00 51 3740 66.53 1.5 Silver*
C2-1210 1010 458 1.67 42 4-C2-7480 6245 2833 1.67 42
C2-1540 1285 583 1.67 42 6-C2-7260 6060 2749 1.67 42 6-C2-7260† 7260 3293 2.00 51 3630 64.57 2.7 Silver
C2-1870 1560 708 1.67 42 6-C2-9240 7715 3500 1.67 42 6-C2-9240† 9240 4191 2.00 51 4620 82.18 2.1 Gray*
2-C2-1760 1600 726 1.67 42 6-C2-11220 9370 4250 1.67 42 6-C2-11220† 11220 5089 2.00 51 5610 99.78 1.7 Silver*
2-C2-2420 2020 916 1.67 42 9-C2-13860 11570 5248 1.67 42 9-C2-13860† 13860 6287 2.00 51 6930 123.27 1.9 Gray*
9-C2-16830† 16830 7634 2.00 51 8415 149.69 1.6 Silver*
TYPE SLRS DIMENSIONS (inches and mm) All springs without “†” have additional travel
SLRS SLRSEBP to solid equal to 50% of the rated deflection.
Size H T D E L HCL W HCW MBD EL EHCL F EW EHCW EMBD All springs with “†” have additional travel to
81/2 3/8 1/2 11/8 81/2 7 41/4 23/4 5/8 10 8 - 9 71/4 3/4 solid equal to 25% of the rated deflection.
B 216 10 13 29 216 178 108 70 16 254 203 229 184 19
B2 81/2 3/8 5/8 13/8 91/2 71/2 51/4 31/2 5/8 10 8 - 9 71/4 3/4 Designs using these mounts to resist
C2 216 10 16 35 241 191 133 89 16 254 203 229 184 19 wind loads must be in accordance with
8 1/2 3/8 5/8 13/8 14 12 1/4 51/4 31/2 5/8 14 12 - 11 9 7/8 ASCE 7-02.
2-C2 216 10 16 35 356 311 133 89 16 356 305 295 229 22 Solid Spring Height = Free Height
1/2 3/8 7/8 13/8 11 83/8 61/4 3/4 17 14 12 11/8
4-C2 8216 13 12 - minus 1.5 times the Rated Deflection.
10 22 35 330 279 213 159 19 432 305 356 305 29
Housing load ratings expressed in G’s
9 1/2 1 15/8 161/2 14 83/8 6 1 27 - 12 15 12 11/8
6-C2 229 are based on tests with bolted
13 25 41 419 356 213 152 25 686 305 381 305 29 Tm306
connections to steel top and bottom.
3/4 5/8 17 143/4 13 103/4 1 18 15 11/8 6/03
9-C2 9216 1 2 27 - 12 SLRS housings require uniform support
16 25 51 432 375 330 273 25 686 305 457 381 29 under entire base plate. Printed
in U.S.A.