LESER worldwide

Modulate

Modulate Action
André Ramseyer AG Hong Kong LESER
Action
Flamatt, Switzerland Shenzen, China
[email protected] [email protected]
Safety Relief Valves
LESER UK
Bristol,
United Kingdom
Series 433
[email protected]

LESER Polska
Series 429
Poznan, Poland
[email protected]

LESER LLC LESER S.A.R.L.

Charlotte (NC), Toulouse, France
USA [email protected]
[email protected] LESER LLP
Singapore
[email protected]

PROTEGO–LESER do BRASIL
Rio de Janeiro, Brazil
[email protected] LESER Office FAINGER LESER Valves
Middle East Mumbai, India
Bahrain [email protected]
LESER representative [email protected]

LESER stock and local assembly

Modulate Action
Edition January 2011 / 2000
LWN 485.01-E / 0777.5646 CATALOG
The-Safety-Valve.com The-Safety-Valve.com
LESER GmbH & Co. KG 20537 Hamburg, Wendenstr. 133-135 Fon +49 (40) 251 65-100 Email: [email protected]
20506 Hamburg, P.O. Box 26 16 51 Fax +49 (40) 251 65-500 www.leser.com

E
Valve finder
LESER Safety Valves for every industrial application

Modulate
Action

High
Performance
Series 433

Type 431, 433

Compact
Performance
Type 431, 433 PN 160

API

High
Efficiency

Clean
Series 429
Service
Type 427, 429

Critical
H 2 SO 4
HNO 3 Service
NH 3
HCL

Best
Availability
 General
General

Type 431, 433

DN 15 – DN 150

Type 433
Set pressure 0.2 – 40 bar

Type 431, 433 PN 160

Type 433 PN 160

DN 15
Set pressure 0.3 – 160 bar

Type 427, 429

DN 15 – DN 150

Type 429
Set pressure 1.5 – 40 bar

Options
Options
Contents

Overview Chapter/Page LESER Type Chapter/Page

General Type 433 PN 160 02/01

General Information 00/01 Materials
• Conventional design 02/02
Applications, General design features 00/02 • Balanced bellows design 02/04

Valve guide 00/03 How to order:

• Numbering system 02/06
Valve selection 00/05
• Article numbers 02/08
How to use:
00/07 Pressure temperature ratings
Signs and symbols, Flange drillings and facings
•Metric units 02/09
How to use:
00/08 Dimensions and weights
Determination of coefficient of discharge Kdr /αw
•Metric units 02/10
How to use: Capacity sheets 00/09
Flange drillings and facings 02/11
LESER Effective Orifice LEOS/G 00/11
Order information - spare parts 02/12
LESER Effective Orifice LEOL 00/12
Available options 02/13
Sour gas service 00/13
Approvals 02/14

Capacities
Chapter/Page • Steam, air, water Metric units 02/15
LESER Type
Determination of coefficient of discharge Kdr /αw 02/16
Type 431, 433 01/01
Materials
• Conventional construction 01/02
• Balanced bellows construction 01/04

How to order:
• Numbering system 01/06
• Article numbers 01/08

Pressure temperature ratings

•Metric units 01/10

Dimensions and weights

• Metric units 01/12

Approvals 01/13

Flange drillings 01/14

Flange facings 01/15

Order information - spare parts 01/16

Available options 01/18

Capacities
• Steam Metric units 01/19
• Air Metric units 01/20
• Water Metric units 01/21

Determination of coefficient of discharge Kdr /αw 01/22

Type 433 Type 433 Type 431 Type 433 PN 160

Plain lever H3 Cap H2 Plain lever H3 Packed lever H4
Closed bonnet Closed bonnet Open bonnet Closed bonnet
Conventional design Balanced bellows design Conventional design Conventional design
Contents

LESER Type Chapter/Page Chapter/Page

Type 427, 429 03/01 Options 99/01

Materials Overview 99/02
• Conventional design 03/02
• Balanced bellows design 03/04 Caps and lever 99/04

How to order: Metal seat 99/06

• Numbering system 03/06
Soft seal disc 99/08
• Article numbers 03/08
Soft seal 99/10
Pressure temperature ratings
•Metric units 03/10 Disc 99/11
Dimensions and weights
Balanced bellows 99/12
• Metric units 03/12
Heating jacket 99/14
Flange drillings and facings 03/13
O-ring damper 99/16
Order information - spare parts 03/14
Elastomer bellows 99/18
Available options 03/16
Lift indicator 99/19
Approvals 03/17
Lift restriction 99/20
Capacities
• Steam Metric units 03/18
• Air Metric units 03/19
• Water Metric units 03/20

"3 / 08 SPN 724 epyT

04 NP .xam

Type 433 PN 160 Type 431 PN 160 Type 429 Type 427
Cap H2 Plain lever H3 Packed lever H4 Cap H2
Closed bonnet Open bonnet Closed bonnet Open bonnet
Balanced bellows design Conventional design Conventional design Conventional design
 General Information
General

LESER – Modulate Action Safety Valves

The Modulate Action product group stands for

✓ Suitable solutions for all areas of applications,

especially thermal expansion
✓ Lowest possible loss of medium
✓ Compact construction and low weight

LESER Modulate Action Safety Valves

• are characterised by longstanding proof in service

and are constantly optimised by service specialists.
• are available as standard safety valves or proportional
safety valves.
• reach their full lift within a pressure increase of 10% above
the set pressure
• are suitable for almost all industrial applications.
• are accepted by numerous rules and regulations and
approved by leading classification societies.

Examples of this are:

- European Community: CE marking as per Pressure

Equipment Directives 97/23/EG and DIN EN ISO 4126-1
- Germany: VdTÜV approval as per Pressure Equipment
Directive, EN ISO 4126-1, TÜV SV 100 and
AD 2000-Merkblatt A2
- China: AQSIQ based on the approvals as
per AD 2000-Merkblatt A2
- Russia: TR and RTN based on
the AD 2000-Merkblatt A2 approval

Furthermore, all LESER Modulate Action safety valves

are constructed, identified, produced, and approved
in compliance with the following regulations:

EN ISO 4126-7, EN 12266-1/-2, EN 1092 Part I and II Flange,

ASME B 16.34 and ASME B16.5- Flange,
AD 2000-Merkblatt A4, AD 2000-Merkblatt HP0,
TRD 110, TRD 421, TRD 721

LESER Modulate Action safety valves can be used for all

steam, gas, and liquid applications and are characterised by
their low loss of medium.

The Series 433 standard safety relief valves have component

testing according to AD 2000-Merkblatt AT for steam, gases,
and liquids. For the Series 429 proportional safety valves, there
is only component testing as per AD 2000-Merkblatt A2 for
steam and gasses, because the required coefficient of discharge
is not reached for liquids. Nevertheless, Series 429 can be
used as per the rules and regulations for thermal expansion.

Furthermore, Series 429 proportional safety valves are used

as overflow valves or in bypass systems.

00/01 LWN 485.01-E

General Information

General
Applications General design feature

LESER – Modulate Action Safety Valves LESER – Modulate Action Safety Valves

provide the ultimate solution for all industrial applications offer a large number of models, materials, and accessories
with steam, gasses, and liquids. for adaptation to any application:

Series 433 standard safety valves • 11 valve sizes from DN 15 to DN 150 – 1/2" up to 6" with
acc. to definition AD 2000-Merkblatt A2 connection possibilities for the respective application
are ideal relief valves for medium mass flows. Their greater • Nominal pressure ratings from PN 16 to PN 160 / Class 150
proportional range leads to a constant mode of operation to Class 600 fulfil most pressure requirements
and relief of pressure peaks for liquids in particular. • Orifice 0.2 x D to > 1.1 x M cover all common performance
requirements.
Typical applications for LESER Modulate Action Series 433 • The required material for the application can be chosen from
safety valves are: the large choice of body materials, for example:
– 0.6025 / cast iron (Series 433)
• chemical industry – 0.7043 / ductile iron
– recycling facilities: Low medium loss – 1.0619 / WCB
– piping with long line lengths – 1.4408 / CF8M
– two-phase flow • centre to face dimensions acc. to DIN 3320
– waste gas purification systems on the outlet side • set pressures from 0.2 to 160 bar qualify Modulate Action
safety valves for all industrial systems
• heat-transfer oil systems • operating temperatures from -270 to 450 °C make use
possible in numerous applications
• liquids protection • compact construction and low weight for easy handling
– metering pumps • same nominal inlet and outlet diameter
– hydraulic systems • identical construction for steam, gasses and liquids
– pulsating operating pressures (single trim) reduces the number of required spare parts
and facilitates cost-effective maintenance
• machine building (OEM) • construction without a blow down ring guarantees easy
– piston compressors with small and medium capacities service and prevents incorrect settings of the blow down ring
• the one-part spindle reduces friction, guarantees optimal
• overflow function guidance and reliable operation under all operating conditions
• the self-emptying angle type body prevents residue and
• thermal expansion reduces corrosion
– protection of pipeline segments
– sealed storage tanks LESER – Modulate Action safety valves can be individually
adapted to the applications with a multitude of accessories.
Series 429 proportional safety valves Examples are:
acc. to definition AD 2000-Merkblatt A2 • discs with soft seal (O-ring) fulfil increased demands
opens proportional to pressure increase. This is usually of functional tightness
achieved by using a disc without a lifting aid. Proportional • stellited or hardened metal seat surfaces of disc
safety valves are normally used anywhere where only very and seat reduce the wear and increase the service life
small mass flows are to be expected and the medium loss • balanced bellows for compensation of the back pressure
is to be kept as low as possible (e. g. thermal expansion). and to protect the moving parts
• heating jacket for heating the safety valve
Both proportional as well as standard safety valves are when protecting cold stiff media
characterised by particularly stable operation. • each component can be constructed of an alternative
material according to customer specifications

LWN 485.01-E 00/02

 Valve finder
General

How to find the right Product Group

controlled
High

Medium-
High operating to set
Yes
pressure ratio, high backpressure Efficiency
or low total height?

No

Clean
Clean Service Yes
application? Service

No

Critical
Critical Service / highly corrosive Yes
application? Service

No

Safety Valves
API
API specified Yes
application?

Spring loaded
No

Steam, gas and liquid application Modulate

Yes
with low capacity in relation Action
to valve size?

No

Orifice ≥ F High
Performance

Required
Orifice letter?
Compact
Performance
Orifice ≤ F
over valve
Change-

Bursting

Best
disc

Additional components Yes

beyond safety valves Availability

00/03 LWN 485.01-E

Valve finder

General
How to find the right Modulate Action Safety Valve

Type 431 Type 433 Type 431 PN 160 Type 431 PN 160 Type 427 Type 429

Open bonnet Closed bonnet Open bonnet Closed bonnet Open bonnet Closed bonnet

Type 431 Type 431 PN 160 Type 427

Type 433 Type 433 PN 160 Type 429

PN 40 PN 160 PN 40
Class 300 Class 600 Class 300

Standard Safety Valve Proportional Safety Valve

acc. to definition AD 2000-Merkblatt A2 acc. to definition AD 2000-Merkblatt A2
for medium capacities with a large proportional range with linear opening and closing characteristics
Mainly used for thermal expansion. proportional to increasing or falling pressure
Mainly used with incompressible media

Lift Lift

max.

max.

Set pressure Set pressure

p + 10% p + 10%

How to find the right

Modulate Action Safety Valve

LWN 485.01-E 00/04

 Valve selection
General

Valve size
Type 431 / 433 433 PN 160 427 / 429

DN 15 DN 15 DN 15
min.
1 1 1
/2 " /2 " /2"

DN 150 DN 15 DN 150
max.
1
6" /2 " 6"

Materials
Type 431 / 433 433 PN 160 427 / 429

0.6025 Cast iron ✓ – –

0.7043 Ductile 60-40-18 ✓ – ✓

1.0619 WCB ✓ ✓ ✓

1.4408 CF8M ✓ ✓ ✓

Set pressure
Type 431 / 433 433 PN 160 427 / 429

Metric units min. [bar] 0.2 0.3 1.5

Metric units max. [bar] 40 160 40

Temperature application range

Type 431 / 433 433 PN 160 427 / 429

According to DIN EN min. [°C] -270 -270 -270

According to DIN EN max. [°C] 450 450 450

00/05 LWN 485.01-E

Valve selection

General
Capacity
Type 431 / 433 433 PN 160 427 / 429

Attention: Series 433 and 429 are CE certified, however not according to ASME.
LEOS/G min. 0.111 0.111 0.023
LEOS/G max. 4.016 0.111 1.374
OrificeS/G min. 1.0 x D 1.0 x D 1.0 x D
OrificeS/G max. 1.1 x M 1.0 x D 1.07 x J
LEOL min. 0.115 0.129
The required discharge coefficient
LEOL max. 3.963 0.127 for liquids of αw 0.05
acc. to AD 2000-Merkblatt A2
OrificeL min. 1.0 x D 1.2 x D is not reached, therefore
a component test is not possible.
OrificeL max. 1.1 x M 1.2 x D

Coefficient of discharge
Type 431 / 433 433 PN 160 427 / 429
DN 15 DN 15 DN 20 DN 25
DN 15 DN 15
O-ring Metal – 150
O-ring disc Metal seat
disc seat

Pressure increase acc. to DIN EN ISO 4126 10% 10% 10% 10% 10% 10% 10%
Kdr / αw S/G 0.59 0.62 0.29 0.38 0.59 0.62 0.13

The required discharge coefficient

for liquids of αw 0.05
Kdr / αw L 0.47 0.48 0.19 0.25 0.47 0.48 acc. to AD 2000-Merkblatt A2
is not reached, therefore
a component test is not possible.

Approvals
Type 431 / 433 433 PN 160 427 / 429
Country Code Media HDD

DIN EN ISO 4126-1

Europe
CE marking
S/G/L 072020111Z0008/0/06 072020111Z0008/0/06 072020111Z0008/0/04
AD 2000-
Germany
Merkblatt A2
S/G/L TÜV SV 577 TÜV SV 577 TÜV SV 610
China AQSIQ S/G/L ✓ ✓ –
Russia TR / RTN S/G/L ✓ ✓ –
Kazakhstan GOST-K S/G/L ✓ ✓ –
Belarus GOSPROMNAZADOR S/G/L ✓ ✓ ✓
Classification societies
Bureau Veritas BV ✓ ✓
ClassNK NIPPON Kaiji Kyokai NK ✓ ✓
Det Norske Veritas DNV ✓ ✓
On request
Germanischer Lloyd GL ✓ ✓
Lloyd`s Register EMEA LREMEA ✓ ✓
Registro Italiano Navale RINA ✓ ✓

LWN 485.01-E 00/06

 How to use
General

General signs and symbols Signs and symbols for flange drillings and flange facings
Standard Standard construction, specification of an option code not necessary
* *
Flange dimensions with exception of flange thickness as per flange standards
✓ Available (*) (e.g. ASME B16.5) Flange thickness is less (max. 2 mm), see “Hole patterns valid
for different pressure ratings”
– Not possible – Flange hole pattern / sealing surface not possible

Option code for flange drillings and dimensions, e.g. H50

Flange drilling as specified in flange standard

H50
Outer flange diameter, flange thickness and height of flange facing may be larger, see “Dimensions”
Flange dimensions except flange thickness are in accordance with standards (e.g. ASME B16.5)
(H50)
Flange thickness is smaller (max. 2 mm), see “Multiple pressure rating”
Flange drilling as specified in standard. Flange thickness may be less than the flange outer diameter as specified
Stock Fini
in the standard, however complete nut support area is available
Option code for flange sealing surfaces, e.g. L36

L36 Flange facing as specified in standard (e.g. Flange facing inlet Type B2 “smooth finish”)

General information concerning flange drillings and flange facings

Multiple
The flange standard shows the same drilling, facing and outer diameter for several pressure ratings, e.g. from PN 16 to PN 40.
pressure
Due to the pressure rating of the body, LESER fulfills the requirements for flange thickness, e.g. PN 16 but not PN 40.
rating

In the applicable MSS SP-6 (Edition 2001), “Smooth Finish” is no longer mentioned. In MSS SP-6 (Edition 1980), “Smooth
Finish” was defined as the surface quality of the flange with “250 µinch (6.3 µm) AARH max.”. LESER supplies flange
Smooth Finish sealing surfaces according to ASME B16.5 – 1996, Paragraph 6.4.4.3: “Either a serrated concentric or serrated spiral finish
resulting in service finish from 125 to 250 µinch average roughness shall be furnished” This finish meets the requirements
of MSS SP-6 (Edition 1980), which is not valid anymore!

“Stock Finish” is not defined in any technical standard. If “Stock Finish” is specified in the order, then LESER delivers
Stock Finish
standard flange sealing surfaces as per DIN or ASME (marked with in the “Flange sealing surfaces” table for each series).
*
Pressures – Symbols in use
Symbols Name Metric units
p Set pressure bar
p0 Absolute pressure in vessel
= p · 1.1 + 1.013 bara
= p · 1.1 + 14.5
The overpressure is 10% of the set pressure, but at least 0.2 bar
pa Back pressure bar
pa0 Absolute back pressure
(= pa + 1.013) bara
(= pa + 14.5)

Materials
In the table below, you will find a list of the LESER material codes. Please take into consideration that
– material quality certificate 3.1 acc. to EN 10204 is available for each body material
– material quality certificate 3.1, which certifies different materials, is available for many materials.
Body material is certified acc. to 3.1 (EN 10204) for the following materials
Material code Valve body with flanges
acc. to DIN EN acc. to ASME
xxx1.xxxx Grey iron 0.6025 Cast iron
xxx2.xxxx Carbon steel 1.0619 WCB, WCC
xxx4.xxxx Stainless steel 1.4408, 1.4581 CF8M (Charpy Test at -196°C), CF10M
xxx5.xxxx Nodular cast iron 0.7043 Ductile Gr. 60-40-18
xxx7.xxxx High temperature carbon steel 1.7357 WC6

00/07 LWN 485.01-E

How to use

General
Example of determination of Kdr/αw : Type 433 DN 25

Type 431, 433

Determination of coefficient of discharge h = Lift [mm]
d0 = Flow diameter [mm] of selected safety
in case of a lift restiction or back pressure valve see “Article Numbers” table
h/d0 = Ratio of lift / flow diameter
pa0 = Back pressure [bara]
p0 = Set pressure [bara]
pa0/p0 = Ratio of back pressure / set pressure
Kdr = Coefficient of discharge
acc. to DIN EN ISO 4126-1
αw = Coefficient of discharge
Diagram for evaluation of ratio of lift / flow diameter (h/d0)
acc. to AD 2000-Merkblatt A2
in reference to the coefficient of discharge (Kdr/αw)
Kb = Back pressure correction factor
acc. to API 520 Section 3.3

1 Kdr = αw = f (h/d0)
0.8 Kdr = αw = f (h/d0)
0.8

0.7
0.7
DN15, Metal disc, S/G
0.6
0.6

0.5
0.5
DN15, Metal disc, L

1a 0.4
Coefficient of discharge Kdr / αw

DN25 – DN150, S/G 0.4

Coefficient of discharge Kdr / αw

DN15, O-ring-disc, S/G DN15, O-ring-disc, L

0.32 0.3
0.3
DN25 – DN150, L

0.2
0.2
DN20, L

0.1 DN20, S/G

0.1

0
0
0 0.1 0.2 0.3
0.110 0.208 0 0.1 0.2 0.3
0.110 0.208
Ratio of lift / flow diameter h / d0
Ratio of lift / flow diameter h / d0
0.09
1b

Diagram for evaluation of coefficient of discharge (Kdr/αw) or Kb in reference

to the ratio of back pressure / set pressure (pa0/p0)

2 Kdr = αw = f (pa0/p0)
0.8

0.7
DN15 Metal disc

0.6

DN15 O-ring-disc
0.5

2b DN25 – 150
0.4
Coefficient of discharge Kdr / αw

0.330 0.3

0.2
DN20

0.1

0
0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900
0.503 0.833
Ratio of back pressure / set pressure pa0 / p0

2a

Explanation Example – Type 433, flow diameter d0 = 13 mm, Lift h = 3.0 mm, Kdr /αw D/G = 0.81

1 Diagram 1 2 Diagram 2
Determining the restricted lift due to reduced Kdr /αw Determination of reduced Kdr /αw or Kb1) due to back pressure

Step Description Example Step Description Example

Calculation of the necessary coefficient of discharge 1a Calculation of the back pressure pa0 /p0 with the use of 2a
1 for the selected safety valve. The applicable formulas 1 the set pressure p0 [bara] 0.962 and the back pressure
are to be taken from from the codes and standards. Kdr /αw = 0.32 pa0 [bara] 1.913 pa0 /p 0 = 0.503

Choose the starting point (0.3) on the Y-axis Choose the starting point (0.503) on the X-axis of the
2 2
of the diagram diagram
Draw a horizontal line to determine the Draw a vertical line to determine the intersection point
3 3
intersection point of the curves. of the curves.

Draw a vertical line through the intersection point Draw a horizontal line through the intersection point
1b 2b
4 on the X-axis to determine the ratio of lift / flow 4 on the Y-axis to determine the reduced coefficient of
diameter (h/d0). h/d0 = 0.09 discharge Kdr /αw Kdr /αw = 0.330

Calculation of the lift stopper with the formula Calculation of the valve with the established coefficient
h = 18 x 0.09
5 h = d0 x h/d0. (To order the lift restriction, please 5 of discharge Kdr /αw or the correction factor for back
h = 1.62 mm
choose option code J51; see page 99/20). pressure Kb

LWN 485.01-E 00/08

 How to use
General

Sample capacity table –

How to selcet capacities for steam: Type 433 DN 25

Capacity table – steam

Capacities for satureted steam according to AD 2000-Merkblatt A2,

based on set pressure plus 10% overpressure.

1
Metric units AD 2000-Merkblatt A2 [kg/h]

O-ring Metal
disc seat
2
DNI 15 15 20 25 32 40 50 65 80 100 125 150
3
DNO 15 15 20 25 32 40 50 65 80 100 125 150
4
Actual Orifice diameter
12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
5
Actual Orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
6
LEOS/G*) [inch2] 0.111 0.111 0.117 0.154 0.154 0.251 0.399 0.650 1.004 1.708 2.598 4.016
Set pressure [bar] 7 Capacity [kg/h]
0.2 34 34 55 88 142 220 375 570 880
0.5 55 53 30 63 63 102 163 265 410 697 1060 1638
1 78 78 67 101 8 101 165 263 428 661 1125 1711 2645

Explanation Type 433 DN 25

No. Name Metric units Example

1 Code AD 2000-Merkblatt A2

2 Nominal inlet diameter DNI 25

3 Nominal outlet diameter DNO 25

4 Actual orifice diameter d0 [mm] 18

5 Actual orifice area A0 [mm2] 254

6 LESER Effective Orifice LEOS/G [inch2] 0.154

7 Set pressure [barg] 1

8 Capacity [kg/h] 101

9 Calculation basis See table on page 00/10

00/09 LWN 485.01-E

How to use

General
9

Calculation basis
Metric units

Code Capacity calculation according to AD 2000-Merkblatt A2

Medium

Steam table IAPWS-IF97 IAPWS Industrial

Steam Standard
Formulation for the Thermodynamic Properties [kg/h]
(Saturated steam) conditions
of water and steam

Standard
Air 0 °C and 1013 mbar [mn3/h]
conditions

Standard
Water 20 °C [103 kg/h]
conditions

All media

Design pressure Set pressure plus 10% overpressure

Design pressure
for low set Capacity at 1 bar (14.5 psig) and lower are calculated at 0.1 bar (1.45 psig) overpressure.
pressures

Example Determining the design pressure

Metric units

Set pressure Design pressure

10 bar 10 bar + 10% overpressure = 11 bar

0.5 bar 0.5 bar + 0.1 bar overpressure = 0.6 bar

LESER Effective Orifice

Pressure relief devices may be initally sized using the equations This way, the designer can determine a preliminary valve
shown in API RP 520, Section 3.6 to 3.10 for steam, gasses, size. By using the LESER Effective Orifice (LEO), the
liquids, or two-phase flow. These equations use the coefficient designer can select the safety valve directly according
of discharge (S/G 0.975, L 0.650) and the effective area (acc. to the calculation. A verification with the selected actual
to API Std. 526, Fifth Edition, June 2002, table 1), which are orifice area and the accorded coefficient of discharge is not
independent of the valve design. necessary.

LEOS/G LESER Effective Orifice (for steam and gasses) [inch2] see page 00/11

LEOL LESER Effective Orifice (for liquids) [inch2] see page 00/12

For further information refer to LESER ENGINEERING at www.leser.com/engineering.

LWN 485.01-E 00/10

 LEOS/G
General

The table is based on the accorded coefficient of discharge for steam and gases for ASME certified LESER safety valves.
The associated K-values can be seen in the “K-values” column.

LEOS/G [inch2] = A0 [inch2] . ( 0.975

K
)
LEOS/G LESER Effective Orifice (for steam, gas and vapor)
Orifice acc. Kdr/αw-values LEOS/G % of next % of next
LESER series DN Inlet size d0 [mm]
to API 526 K-value1) [inch2] higher orifice lower orifice

429 15 1/2" 12.0 0.130 0.023 21.2%

429 20 3/4" 18.0 0.130 0.053 47.8%
429 25 1" 18.0 0.130 0.053 47.8%
429 32 1 1/2" 18.0 0.130 0.053 47.8%
429 40 1 1/2" 23.0 0.130 0.086 78.1%
433 15 O-ring disc 1/2" 12.0 0.590 0.106 96.4%
D 0.110 100.0% 100.0%
433 15 Metal seat 1/2" 12.0 0.620 0.111 56.9% 101.3%
433 20 3/4" 18.0 0.290 0.117 56.9% 106.7%
429 50 2" 29.0 0.130 0.137 69.6% 124.1%
433 25 1" 18.0 0.380 0.154 78.4% 139.8%
433 32 1 1/2" 18.0 0.380 0.154 78.4% 139.8%
E 0.196 100.0% 100.0%
429 65 2 1/2" 37.0 0.130 0.222 72.4% 113.4%
433 40 1 1/2" 23.0 0.380 0.251 81.8% 128.1%
F 0.307 100.0% 100.0%
429 80 3" 46.0 0.130 0.343 68.3% 111.9%
433 50 2" 29.0 0.380 0.399 79.3% 130.0%
G 0.503 100.0% 100.0%
429 100 4" 60.0 0.130 0.584 74.4% 116.2%
433 65 2 1/2" 37.0 0.380 0.650 82.7% 129.1%
H 0.785 100.0% 100.0%
429 125 5" 74.0 0.130 0.889 69.1% 113.2%
433 80 3" 46.0 0.380 1.004 78.0% 127.9%
J 1.287 100.0% 100.0%
429 150 6" 92.0 0.130 1.374 74.7% 106.7%
433 100 4" 60.0 0.380 1.708 92.9% 132.7%
K 1.838 100.0% 100.0%
433 125 5" 74.0 0.380 2.598 91.1% 141.4%
L 2.853 100.0% 100.0%
M 3.600 100.0% 100.0%
433 150 6" 92.0 0.380 4.016 92.5% 116.3%
N 4.340 100.0% 100.0%
1)
There is no ASME approval for the LESER Modulate Action Series 433 and 429. In order to be able to still use the LEO and hence obtain compatibility to the orifice
acc. to API 526, the Kdr/αw-value (approval acc. to DIN EN ISO 4126-1 and AD 2000-Merkblatt A2) was brought into the calculation.

00/11 LWN 485.01-E

LEOL

General
The table is based on the accorded coefficient of discharge for liquids for ASME certified LESER safety valves.
The associated K-values can be seen in the “K-values” column.

LEOL [inch2] = A0 [inch2] . ( 0.650

K
)
LEOL LESER Effective Orifice (for liquids)
Orifice acc. Kdr/αw-values LEOL % of next % of next
LESER series DN Inlet size d0 [mm]
to API 526 K-value1) [inch2] higher orifice lower orifice

D 0.110 100.0% 100.0%

433 20 3/4" 18.0 0.190 0.115 58.8% 104.8%
433 15 O-ring disc 1/2" 12.0 0.590 0.127 64.8% 115.5%
433 15 Metal seat 1/2" 12.0 0.480 0.129 66.0% 117.7%
433 25 1" 18.0 0.250 0.152 77.4% 137.9%
433 32 1 1/2" 18.0 0.250 0.152 77.4% 137.9%
E 0.196 100.0% 100.0%
433 40 1 1/2" 23.0 0.250 0.248 80.7% 126.4%
F 0.307 100.0% 100.0%
433 50 2" 29.0 0.250 0.394 78.3% 128.3%
G 0.503 100.0% 100.0%
433 65 2 1/2" 37.0 0.250 0.641 81.7% 127.4%
H 0.785 100.0% 100.0%
433 80 3" 46.0 0.250 0.991 77.0% 126.2%
J 1.287 100.0% 100.0%
433 100 4" 60.0 0.250 1.686 91.7% 131.0%
K 1.838 100.0% 100.0%
433 125 5" 74.0 0.250 2.564 89.9% 139.5%
L 2.853 100.0% 100.0%
M 3.600 100.0% 100.0%
433 150 6" 92.0 0.250 3.963 91.3% 110.1%
N 4.340 100.0% 100.0%

1)
There is no ASME approval for the LESER Modulate Action Series 433. In order to be able to still use the LEO and hence obtain compatibility to the orifice
acc. to API 526, the Kdr/αw-value (approval acc. to DIN EN ISO 4126-1 and AD 2000-Merkblatt A2) was brought into the calculation.

LWN 485.01-E 00/12

 Sour gas service (H2S)
General

Normative basis

NACE MR0175-2003 Section 1.4.2.2 Low-pressure oil and gas multiphase

In accordance with NACE standard MR0175-2003 sour gas systems: …
service means the presence of H2S in the following conditions:
Other Sour gas standards:
Section 1.4.1.1 All gas, gas condensate, and sour crude oil NACE MR0103-2003: Materials resistance to sulfide stress
– When the partial pressure of H2S in a wet cracking in corrosive petroleum
(water as a liquid) gas phase of a gas, gas refining environments.
condensate, or crude oil system is equal to DIN EN ISO 15156-1: Petroleum and natural gas industries
or exceeds 0.003 barg (0.05 psia) – Materials for use in H2S containing
environments in oil and gas produc-
Exceptions are: tion – Part 1: General principles for
Section 1.4.2.1 Low-pressure gas selection of cracking-resistant materi-
When the total pressure is lower than als (ISO 15156-1:2001)
4.5 bara (65 psia) Works standard: Please refer to LWN 001.91
General requirements for the use of sour gas
The standards given above require a maximum hardness of 22 HRC for most steels.
The current requirements for a specific material are to be taken for the applied standards.
LESER sour gas level
General: The material requirements for the use of sour gas must be met if pressures and partial pressures are present according
to the applied standards.
If an NACE construction is desired, then option code N78 must be selected.
The option codes for the individual components are given in the following table.

Based on this general statement, LESER defines two sour gas levels for safety valves:

Level 1 Level 2
Parts in contact with the medium Parts in contact with the medium
Definition
with valve closed with open, flowing valve
Balanced Balanced
Conventional Conventional
bellows bellows

Contact surfaces

Pressure requirements Set pressure ≥ 4.5 bara Back pressure ≥ 4.5 bara
Safety valve operation closed closed / open
Conventional
Body / seat / disc All
design
Affected components Body / seat / disc
Balanced bellows
Body / seat / disc Bonnet spacer,
design
Bellows
Required material adjustment
Body
Type Design Part Material Option code Material Option code
material
4292 Please choose
Conventional Disc 1.4404 / 316L L44
4332 1.0619 balanced bellows construction
4332 PN 160 (WCB) Disc 1.4404 / 316L L44 1.4404 / 316L L44
Balanced bellows
Balanced bellows 1.4571 / 316Ti J78 1.4571 / 316Ti J78
4294
Conventional No adjustment required No adjustment required
4334 1.4408
4334 PN 160 (CF8M)
Balanced bellows Balanced bellows 1.4571 / 316Ti J78 1.4571 / 316Ti J78

00/13 LWN 485.01-E

 Type 431
Plain lever H3
Open bonnet
Conventional design
Type
431, 433

Type 433
Flanged Safety Relief Valves
- spring loaded

Contents Chapter/Page
Materials
• Conventional design 01/02
• Balanced bellows design 01/04
How to order
• Numbering system 01/06
• Article numbers 01/08
Type 433 Pressure temperature ratings
Cap H2 • Metric units 01/10
Closed bonnet Dimensions and weights
Conventional design • Metric units 01/12
Approvals 01/13
Flange drillings 01/14
Flange facings 01/15
Order information – spare parts 01/16
Available options 01/18
Capacities
• Steam [Metric units] 01/19
• Air [Metric units] 01/20
• Water [Metric units] 01/21
Determination of 01/22
coefficient of discharge Kdr /α w

LWN 485.01-E 01/01

 Type 431, 433
Conventional design

40 Cap H2

18 Adjusting screw with bushing

Type 433

19 Lock nut

16 Upper spring plate

12 Spindle

9 Bonnet

54 Spring

14 Split ring

55 Stud

56 Nut

17 Lower spring plate

60 Gasket

8 Guide with bushing

57 Pin

61 Ball

7 Disc

5 Seat

1 Body

01/02 LWN 485.01-E

Type 431, 433
Conventional design

Materials
Item Component Type 4311 / 4331 Type 4315 / 4335 Type 4312 / 4332 Type 4334

0.6025 0.7043 1.0619 1.4408

1 Body
Cast iron Ductile Gr. 60-40-18 SA 216 WCB SA 351 CF8M
1.4404 1.4404 1.4404 1.4404
5 Seat
316L 316L 316L 316L

Type 433
1.4122 1.4122 1.4122 1.4404
7 Disc
Hardened stainless steel Hardened stainless steel Hardened stainless steel 316L
1.4104, 1.0501 1.4104, 1.0501 1.4104, 1.0501, 1.0570 1.4404
Guide
Chrome or carbon steel Chrome or carbon steel Chrome or carbon steel 316L
8
1.4104 tenifer 1.4104 tenifer 1.4104 tenifer –
with bushing
Chrome steel tenifer Chrome steel tenifer Chrome steel tenifer –
0.7040 0.7040 0.7040 1.4408, 1.4404
9 Bonnet
Ductile Gr. 60-40-18 Ductile Gr. 60-40-18 Ductile Gr. 60-40-18 SA 351 CF8M, SA 479 316L
1.4021 1.4021 1.4021 1.4404
12 Spindle
420 420 420 316L
1.4104 1.4104 1.4104 1.4404
14 Split ring
Chrome steel Chrome steel Chrome steel 316L
1.0718 1.0718 1.0718 1.4404
16/17 Spring plate
Steel Steel Steel 316L
Adjusting screw 1.4104 PTFE 1.4104 PTFE 1.4104 PTFE 1.4404 PTFE
18
with bushing Chrome steel PTFE Chrome steel PTFE Chrome steel PTFE 316L PTFE
1.0718 1.0718 1.0718 1.4404
19 Lock nut
Steel Steel Steel 316L
1.0718 1.0718 1.0718 1.4404
40 Cap H2
12L13 12L13 12L13 316L
1.1200, 1.8159, 1.7102 1.1200, 1.8159, 1.7102 1.1200, 1.8159, 1.7102 1.4310
Spring, standard
Carbon steel Carbon steel Carbon steel Stainless steel
54
1.4310 1.4310 1.4310 –
Spring, optional
Stainless steel Stainless steel Stainless steel –
1.1181 1.1181 1.1181 1.4401
55 Stud
Steel Steel Steel B8M
1.0501 1.0501 1.0501 1.4401
56 Nut
2H 2H 2H 8M
1.4310 1.4310 1.4310 1.4310
57 Pin
Stainless steel Stainless steel Stainless steel Stainless steel
Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401
60 Gasket
Graphite / 316 Graphite / 316 Graphite / 316 Graphite / 316
1.3541 1.3541 1.3541 1.4401
61 Ball
Hardened stainless steel Hardened stainless steel Hardened stainless steel 316

Please note:

– LESER reserves the right to make changes.

– If several materials are specified LESER defines the material.
– LESER may use higher quality materials without giving prior notice.
– Each component can be constructed of another material according to the customer's specification.
– All components exposed to pressure are highlighted in bold. The material will be specified according to DIN and ASTM here.

LWN 485.01-E 01/03

 Type 431, 433
Balanced bellows design

40 Cap H2

18 Adjusting screw with bushing

19 Lock nut
Type 433

16 Upper spring plate

12 Spindle

9 Bonnet

54 Spring

14 Split ring

17 Lower spring plate

55 Stud

56 Nut

8 Guide with bushing

60 Gasket

11 Bonnet spacer

15 Balanced bellows

60 Gasket

22 Lift stoppers

57 Pin

61 Ball

7 Disc

5 Seat

1 Body

01/04 LWN 485.01-E

Type 431, 433
Balanced bellows design

Materials
Item Component Type 4311 / 4331 Type 4315 / 4335 Type 4312 / 4332 Type 4334

0.6025 0.7043 1.0619 1.4408

1 Body
Cast iron Ductile Gr. 60-40-18 SA 216 WCB SA 351 CF8M
1.4404 1.4404 1.4404 1.4404
5 Seat
316L 316L 316L 316L

Type 433
1.4122 1.4122 1.4122 1.4404
7 Disc
Hardened stainless steel Hardened stainless steel Hardened stainless steel 316L
1.4104, 1.0501 1.4104, 1.0501 1.4104, 1.0501, 1.0570 1.4404
Guide
Chrome or stainless steel Chrome or stainless steel Chrome or stainless steel 316L
8
1.4104 tenifer 1.4104 tenifer 1.4104 tenifer –
with bushing
Chrome steel Chrome steel Chrome steel –
0.7040 0.7040 0.7040 1.4408, 1.4404
9 Bonnet
Ductile Gr. 60-40-18 Ductile Gr. 60-40-18 Ductile Gr. 60-40-18 SA 351 CF8M, SA 479 316L
1.4404 1.4404 1.4404 1.4404
11 Bonnet spacer
316L 3316L 316L 316L
1.4404 1.4404 1.4404 1.4404
12 Spindle
316L 316L 316L 316L
1.4104 1.4104 1.4104 1.4404
14 Split ring
Chrome steel Chrome steel Chrome steel 316L
1.4571 1.4571 1.4571 1.4571
15 Balanced bellows
316Ti 316Ti 316Ti 316Ti
1.0718 1.0718 1.0718 1.4404
16/17 Spring plate
Steel Steel Steel 316L
Adjusting screw 1.4104 PTFE 1.4104 PTFE 1.4104 PTFE 1.4404 PTFE
18
with bushing Chrome steel PTFE Chrome steel PTFE Chrome steel PTFE 316L PTFE
1.0718 1.0718 1.0718 1.4404
19 Lock nut
Steel Steel Steel 316L
1.4404 1.4404 1.4404 1.4404
22 Lift stoppers
316L 316L 316L 316L
1.0718 1.0718 1.0718 1.4404
40 Cap H2
12L13 12L13 12L13 316L
1.1200, 1.8159, 1.7102 1.1200, 1.8159, 1.7102 1.1200, 1.8159, 1.7102 1.4310
Spring, standard
Chrome steel Chrome steel Chrome steel Stainless steel
54
1.4310 1.4310 1.4310 –
Spring, optional
Stainless steel Stainless steel Stainless steel –
1.4401 1.4401 1.4401 1.4401
55 Stud
B8M B8M B8M B8M
1.4401 1.4401 1.4401 1.4401
56 Nut
8M 8M 8M 8M
1.4310 1.4310 1.4310 1.4310
57 Pin
Stainless steel Stainless steel Stainless steel Stainless steel
Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401
60 Gasket
Graphite / 316 Graphite / 316 Graphite / 316 Graphite / 316
1.3541 1.3541 1.3541 1.4401
61 Ball
Hardened stainless steel Hardened stainless steel Hardened stainless steel 316

Please note:

– LESER reserves the right to make changes.

– If several materials are specified LESER defines the material.
– LESER may use higher quality materials without giving prior notice.
– Each component can be constructed of another material according to the customer's specification.
– All components exposed to pressure are highlighted in bold. The material will be specified according to DIN and ASTM here.

LWN 485.01-E 01/05

 Type 431, 433
How to order – Example for numbering system – Type 433

1 Article Number
2 Set Pressure
3 Connections
Type 433

4332.4192 5 barg H45

1 2 3 4 Please enter the units (in gauge)! See page 01/14.

433 2 . 419 2 The specified pressure range may

not be exceeded!
1 Valve type 431, 433
Type 433 – with closed bonnet
Type 431 – with open bonnet

2 Material code

Code Body material

1 0.6025 (cast iron)
2 1.0619 (WCB)
4 1.4408 (CF8M)
0.7043
5
(Ductile Gr. 60-40-18)

3 Valve code
Automatically determines
nominal diameter and
body material (see page 01/09).

Code Lifting device

2 Gas-tight cap H2
3 Plain lever H3
4 Packed lever H4
Plain lever with
5 H3
open bonnet

01/06 LWN 485.01-E

Type 431, 433

4 Options
5 Documentation
6
Code and Medium

Type 433
J22 H01 L30 2.0

Type 431, 433 Option code Please select the necessary

documentation: 1 2
• O-ring disc
CR “K” J21 Tests, Option 2 . 0
Certifications: code
EPDM “D” J22
FKM “L” J23 DIN EN 10204-3.2: TÜV-Nord
1 Code
FFKM “C” J20 Certification for set pressure M33
2. CE / VdTUEV
• Disc 1.4404 / 316L L44 3. ASME Section VIII
LESER CGA (Certificate H03
• Disc1.4404 / 316L stellited J25 + CE / VdTUEV
for Global Application)
• Detachable lifting aid J26
• Balanced bellows - Acceptance test certificate 3.1 2 Medium
- Bonnet, open (Type 431) J68 acc. to DIN EN 10204 .0 steam / gases / liquids
- Bonnet, closed (Type 433) J78 - Declaration of conformity as per (only valid for CE / VdTUEV)
• Elastomer bellows J79 pressure equipment directive
• High temperature alloy spring X01 PED 97/23/EC
• Stainless steel spring X04
• Adaptor for lift indicator H4 J39 Material quality certificate:
• Lift indicator J93 DIN EN 10204-3.1
• Test gag
- Cap H2 J70 Component Option code
- Packed lever H4 J69 Body H01
• Heating jacket Bonnet L30
- Couplings G 3/8 H29 Cap / lever cover L31
G 3/4 H30 Disc L23
- Flange DN 15 H31 Screws N07
DN 25 H32 Nuts N08
• Drain hole G 1/4 J18
G 1/2 J19
• Oil and grease free J85
• Materials
- NACE N78

Option code applies

only if not standard

LWN 485.01-E 01/07

 Type 431, 433
How to order – Article numbers
Type 433

Type 433 Type 433

Cap H2 Plain lever H3
Closed bonnet Closed bonnet
Conventional design Conventional design

Type 433
Packed lever H4
Closed bonnet
Conventional design

Type 431 Type 433

Plain lever H3 Cap H2
Open bonnet Closed bonnet
Conventional design Balanced bellows design

01/08 LWN 485.01-E

Type 431, 433
How to order – Article numbers

Article numbers
O-ring Metal
disc disc
DNI 15 15 20 25 32 40 50 65 80 100 125 150
DNO 15 15 20 25 32 40 50 65 80 100 125 150

Type 433
Actual orifice diameter
12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Body material: 0.6025 (cast iron)
Bonnet H2 Art.-No. 4331. 8502 3992 4012 4022 4032 4042 4052 4062 4072 4082 – –
closed H3 Art.-No. 4331. 8503 3993 4013 4023 4033 4043 4053 4063 4073 4083 – –
H4 Art.-No. 4331. 8504 3994 4014 4024 4034 4044 4054 4064 4074 4084 – –
open H3 Art.-No. 4311. 8505 3995 4015 4025 4035 4045 4055 4065 4075 4085 – –
Body material: 0.7043 (Ductile Gr. 60-40-18)
Bonnet H2 Art.-No. 4335. 8532 8752 8762 8772 8782 8792 8802 8812 8822 8832 – –
closed H3 Art.-No. 4335. 8533 8753 8763 8773 8783 8793 8803 8813 8823 8833 – –
H4 Art.-No. 4335. 8534 8754 8764 8774 8784 8794 8804 8814 8824 8834 – –
open H3 Art.-No. 4315. 8535 8755 8765 8775 8785 8795 8805 8815 8825 8835 – –
Body material: 1.0619 (WCB)
Bonnet H2 Art.-No. 4332. 8512 4122 4142 4152 4162 4172 4182 4192 4202 4212 4222 4232
closed H3 Art.-No. 4332. 8513 4123 4143 4153 4163 4173 4183 4193 4203 4213 4223 4233
H4 Art.-No. 4332. 8514 4124 4144 4154 4164 4174 4184 4194 4204 4214 4224 4234
open H3 Art.-No. 4312. 8515 4125 4145 4155 4165 4175 4185 4195 4205 4215 4225 4235
Body material: 1.4408 (CF8M)
Bonnet H2 Art.-No. 4334. 8522 4252 4272 4282 4292 4302 4312 4322 4332 4342 – –
closed H4 Art.-No. 4334. 8524 4254 4274 4284 4294 4304 4314 4324 4334 4344 – –

LWN 485.01-E 01/09

 Type 431, 433
Pressure temperature ratings

Metric units
O-ring Metal
disc disc
DNI 15 15 20 25 32 40 50 65 80 100 125 150
DNO 15 15 20 25 32 40 50 65 80 100 125 150
Type 433

Actual orifice diameter

12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Body material: 0.6025 (cast iron)
DIN flange Inlet PN 16 – –
Outlet PN 16 – –
Minimum set pressure
p [barg] S/G/L 0.3 0.3 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 – –

Min. set pressure1)

standard bellows p [barg] S/G/L 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 – –

Min. set pressure

low pressure bellows p [barg] S/G/L – – 2.0 2.0 2.0 1.8 1.9 1.8 1.8 1.2 – –

Maximum set pressure

p [barg] S/G/L 16 16 16 16 16 16 16 16 16 16 – –

Max. set pressure

with special spring p [barg] S/G/L 16 16 16 16 16 16 16 16 16 16 – –

Temperature2) min. [°C] -10 -10 – –

acc. to DIN EN max. [°C] +150 +300 – –

Body material: 0.7043 (Ductile Gr. 60-40-18)

DIN flange Inlet PN 40 – –
Outlet PN 40 – –
Minimum set pressure
p [barg] S/G/L 0.3 0.3 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 – –

Min. set pressure1)

standard bellows p [barg] S/G/L 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 – –

Min. set pressure

low pressure bellows p [barg] S/G/L – – 2.0 2.0 2.0 1.8 1.9 1.8 1.8 1.2 – –

Maximum set pressure

p [barg] S/G/L 16 16 16 16 16 16 16 16 16 16 – –

Max. set pressure

with special spring p [barg] S/G/L 16 16 16 16 16 16 16 16 16 16 – –

Temperature2) min. [°C] -45 -60 – –

acc. to DIN EN max. [°C] +150 +350 – –
1)
Min. set pressure of standard bellows = max. set pressure of bellows for low set pressure.
2)
The temperature is limited by the soft seal material (see page 99/10). The values given here are valid for EPDM.
Between -10°C and the lowest specified application temperature, proceed acc. to AD 2000-Merkblatt W10.

01/10 LWN 485.01-E

Type 431, 433
Pressure temperature ratings

Metric units
O-ring Metal
disc disc
DNI 15 15 20 25 32 40 50 65 80 100 125 150
DNO 15 15 20 25 32 40 50 65 80 100 125 150

Type 433
Actual orifice diameter
12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Body material: 1.0619 (WCB)
DIN flange Inlet PN 40
Outlet PN 40
Minimum set pressure
p [barg] S/G/L 0.3 0.3 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2

Min. set pressure1)

standard bellows p [barg] S/G/L 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0

Min. set pressure on

low pressure bellows p [barg] S/G/L – – 2.0 2.0 2.0 1.8 1.9 1.8 1.8 1.2 1.2
request
Maximum set pressure
p [barg] S/G/L 40 40 40 40 40 40 40 35 35 30 32 16

Max. set pressure

with special spring p [barg] S/G/L 40 40 40 40 40 40 40 40 35 30 32 16

Temperature2) min. [°C] -45 -85 – –

acc. to DIN EN max. [°C] +150 +450 – –

Body material: 1.4408 (CF8M)

DIN flange Inlet PN 40 – –
Outlet PN 40 – –
Minimum set pressure
p [barg] S/G/L 0.3 0.3 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 – –

Min. set pressure1)

standard bellows p [barg] S/G/L 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 – –

Min. set pressure

low pressure bellows p [barg] S/G/L – – 2.0 2.0 2.0 1.8 1.9 1.8 1.8 1.2 – –

Maximum set pressure

p [barg] S/G/L 40 40 40 40 40 40 31.6 20.2 25 22 – –

Max. set pressure

with special spring p [barg] S/G/L 40 40 40 40 40 40 40 26 25 22 – –

Temperature2) min. [°C] -45 -270 – –

acc. to DIN EN max. [°C] +150 +400 – –
1)
Min. set pressure of standard bellows = max. set pressure of bellows for low set pressure.
2)
The temperature is limited by the soft seal material (see page 99/10). The values given here are valid for EPDM.
Between -10°C and the lowest specified application temperature, proceed acc. to AD 2000-Merkblatt W10.

LWN 485.01-E 01/11

 Type 431, 433
Dimensions and weights

Metric units
O-ring Metal
disc disc
DNI 15 15 20 25 32 40 50 65 80 100 125 150
DNO 15 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Type 433

Weight 5 5 6 6 8 9 12 15 20 33 48 65
[kg] with bellows 6.3 6.3 6.4 6.4 8.4 9.6 13 16 21.6 35.6 52.1 78.4
Centre to face Inlet a 90 90 95 100 105 115 125 145 155 175 200 225
[mm] Outlet b 90 90 95 100 105 115 125 145 155 175 200 225
Height (H4) Standard H max. 310 310 315 320 325 335 360 475 530 605 745 870
[mm] Bellows H max. 362 362 345 350 360 390 425 535 600 680 825 965
Support brackets A 277
[mm] B 160
(Drilled only on request, C Ø 18
option code H42) D 278
E 21

Body material: 0.6025 (cast iron)

DIN flange1) Inlet PN 16 – –
Outlet PN 16 – –
Body material: 0.7043 (Ductile Gr. 60-40-18)
DIN flange1) Inlet PN 40 – –
Outlet PN 40 – –
Body material: 1.0619 (WCB)
DIN flange1) Inlet PN 40
Outlet PN 40
Body material: 1.4408 (CF8M)
DIN flange1) Inlet PN 40 – –
Outlet PN 40 – –
1)
Standard flange class For other flange drillings, refer to page 01/14 and 01/15.

Conventional design Support brackets Balanced bellows design

01/12 LWN 485.01-E

Type 431, 433
Approvals

Approvals
O-ring disc Metal disc
DNI 15 15 20 25 – 150
DNO 15 15 20 25 – 150
Actual orifice diameter d0 [mm] 12 12 18 18 – 92
Actual orifice area A0 [mm2] 113 113 254 254 – 6648
Europe Coefficient of discharge Kdr

Type 433
PED / DIN EN ISO 4126-1 Approval-No. 072020111Z0008/0/06
S/G 0.59 0.62 0.29 0.38
L 0.47 0.48 0.19 0.25
Germany Coefficient of discharge α w
PED / AD 2000-Merkblatt A2 Approval-No. TÜV SV 577
Standard safety valve S/G 0.59 0.62 0.29 0.38
L 0.47 0.48 0.19 0.25
China Coefficient of discharge K
AQSIQ Approval-No. For current Approval-No. see www.leser.com
S/G 0.59 0.62 0.29 0.38
L 0.47 0.48 0.19 0.25
Russia Coefficient of discharge K
TR/ RTN Approval-No. For current Approval-No. see www.leser.com
S/G 0.59 0.62 0.29 038
L 0.47 0.48 0.19 0.25
Kazakhstan Coefficient of discharge α w
GOST-K Approval-No. For current Approval-No. see www.leser.com
S/G 0.59 0.62 0.29 0.38
L 0.47 0.48 0.19 0.25
Belarus Coefficient of discharge α w
GOSPROMNAZADOR Approval-No. For current Approval-No. see www.leser.com
S/G 0.59 0.62 0.29 038
L 0.47 0.48 0.19 0.25

Classification societies Homepage

Bureau Veritas BV www.bureauveritas.com
The valid Approval-No. changes
ClassNK NIPPON Kaiji Kyokai NK www.classnk.or.jp with each renewal of the approval.
Det Norske Veritas DNV www.dnv.com
Germanischer Lloyd GL www.gl-group.com For a sample certificate including
Lloyd‘s Register EMEA LREMEA www.lr.org the valid certification number
see www.leser.com
Registro Italiano Navale RINA www.rina.org

LWN 485.01-E 01/13

 Type 431, 433
Flange drillings

Flange drillings
O-ring Metal
disc disc
DNI 15 15 20 25 32 40 50 65 80 100 125 150
DNO 15 15 20 25 32 40 50 65 80 100 125 150
Type 433

Valve size 1/2" x 1/2" 1/2" x 1/2" 3/4" x 3/4" 1" x 1" 1 1/4" x1 1/4" 1 1/2" x1 1/2" 2" x 2" 21/2" x 21/2" 3" x 3" 4" x 4" 5" x 5" 6" x 6"
Actual orifice diameter
12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Body material: 0.6025 (cast iron)
PN 10
* * * * * * * * * * * *
PN 16
Inlet DIN EN 1092 * * * * * * * * * * * *
PN 25 – – – – – – – – – – – –
PN 40 – – – – – – – – – – – –
PN 10
Outlet DIN EN 1092 * * * * * * * * * * * *
PN 16
* * * * * * * * * * * *
Body material: 0.7043 (Ductile Gr. 60-40-18), 1.0619 (WCB), 1.4408 (CF8M)
PN 10 H44 H44 H44 H44 H44
* * * * * * *
PN 16 H45 H45 H45 H45 H45
DIN EN 1092 * * * * * * *
PN 25
Inlet * * * * * * * * * * * *
PN 40
* * * * * * * * * * * *
CL150 H64 H64 H64 H64 H64 H64 H64 H64 H64 [H64] H64 H64
ASME B16.5
CL300 [H65] [H65] – H65 H65 – [H65] [H65] – – – –
PN 10 H50 H50 H50 H50 H50
* * * * * * *
PN 16 H51 H51 H51 H51 H51
DIN EN 1092 * * * * * * *
PN 25 * * * * *
Outlet * * * * * * *
PN 40 * * * * *
* * * * * * *
CL150 H79 H79 H79 H79 H79 H79 H79 H79 H79 [H79] H79 H79
ASME B16.5
CL300 H80 H80 – H80 H80 – [H80] [H80] – – – –

For an explanation of the characters and symbols, refer to page 00/07.

Note: Flange drillings and facings always meet the requirements of the given flange standards.
Flange thickness and outside diameter may deviate from the standard.

01/14 LWN 485.01-E

Type 431, 433
Flange facings

Flange facings
Information Standard Inlet Outlet Remark
General
Flange, undrilled – H38 H39
Linde-V-Nut, Form V48 Linde Standard 420-08 J07 J08 Groove: Rz = 16

Type 433
Linde-V-Nut, Form V48A LWN 313.36 J05 J06 Groove: Rz = 4, e.g. for hydrogen
Lens-shape seal form L DIN 2696
J11 J12
(without lens-shape seal) LWN 313.35
According to DIN EN 1092
Flange facings Remark
Inlet Outlet
DIN EN 1092 Rz specification
(also see LWN 313.40) PN 10 – PN 10 – acc. to DIN EN 1092 in µm
PN 40 PN 40

Form B1 Seal. strip.: Rz = 12.5 – 50

Sealing strip * *
Form B2 L36 L38 Seal. strip.: Rz = 3.2 – 12.5

only for steel flange

Tongue, Form C1) H94 H92
Groove, Form D1) H93 H91
Male, Form E H96 H98
Female, Form F H97 H99
O-ring Male, Form G J01 J02
O-ring Female, Form H J03 J04
According to ASME B16.5
Smooth Finish2) Serrated Finish RTJ-Groove

Body material Inlet Outlet Inlet Outlet Inlet Outlet Inlet Outlet
Pressure Option Pressure Option
Option code Option code
level code level code

0.7043 all all L52 L53 – – – –

* *
1.0619, 1.4408 all all L52 L53 CL150 H62 CL150 H63
* *
1)
LESER manufactures the groove at flanged valves by milling. If a customer demands a turned surface in the soil of the groove according to DIN EN 1092-1
an additional option code is necessary: “S01: soil of the groove drilled”.
2)
Smooth Finish is not defined in the effective standards.

For signs and symbols refer to page 00/07

Note: Flange drillings and facings meet always the requirements of mentioned flange standards.
Flange thickness and outer diameter may vary from flange standard.

LWN 485.01-E 01/15

 Type 431, 433
Order information – spare parts

Spare parts
O-ring disc Metal disc
DNI 15 15 20 25 32 40 50
DNO 15 15 20 25 32 40 50
Actual orifice diameter d0 [mm]] 12 12 18 18 18 23 29
Actual orifice area A0 [mm2] 113 113 254 254 254 416 661
Type 433

Disc (item 7): Metal to metal seat Material-No. / Art.-No.

Disc 1.4122 – 230.9339.9000 210.6939.9000 210.6939.9000 210.6939.9000 220.0139.9000 220.0239.9000
Detachable lifting aid 1.4404 – 230.9349.9000 210.6949.9000 210.6949.9000 210.6949.9000 220.0149.9000 220.0249.9000
Disc (item 7): Soft seal Material-No. / Art.-No.
Disc CR “K” 230.3049.9051 – 200.6049.9051 200.6049.9051 200.6049.9051 200.6149.9051 200.6249.9051
EPDM “D” 230.3049.9041 – 200.6049.9041 200.6049.9041 200.6049.9041 200.6149.9041 200.6249.9041
FKM “L” 230.3049.9071 – 200.60049.9071 200.6049.9071 200.6049.9071 200.6149.9071 200.6249.9071
FFKM “C” 230.3049.9091 – 200.60049.9091 200.6049.9091 200.6049.9091 200.6149.9091 200.6249.9091
O-ring (item 7.4): Soft seal Material-No. / Art.-No.
O-Ring CR “K” 502.0107.2651 – 502.0171.2651 502.0171.2651 502.0171.2651 502.0249.3351 502.0313.3551
EPDM “D” 502.0107.2641 – 502.0171.2641 502.0171.2641 502.0171.2641 502.0249.3341 502.0313.3541
FKM “L” 502.0107.2671 – 502.0171.2671 502.0171.2671 502.0171.2671 502.0249.3371 502.0313.3571
FFKM “C” 502.0107.2691 – 502.0171.2691 502.0171.2691 502.0171.2691 502.0249.3391 502.0313.3591
Bellows (item 15): 1.4571 Material-No. / Art.-No.
Standard bellows 400.7949.0000 400.7949.0000 400.0149.0000 400.0149.0000 400.0149.0000 400.0249.0000 400.0349.0000
Conversion kit, standard1) 5021.1030 5021.1030 5021.1034 5021.1034 5021.1034 5021.1035 5021.1036
Low pressure bellows – 400.0149.0021 400.0149.0021 400.0149.0021 400.0149.0021 400.0249.0021 400.0349.0021
Conversion kit low pressure1) Please specify application conditions
Gasket – body / bonnet (item 60) Material-No. / Art.-No.
Gasket Graphite + 1.4401 500.0407.0000 500.0407.0000 500.0407.0000 500.0407.0000 500.0407.0000 500.0407.0000 500.0507.0000
Option code L68 Gylon (PTFE compliance) 500.0405.0000 500.0405.0000 500.0405.0000 500.0405.0000 500.0405.0000 500.0405.0000 500.0505.0000
Ball (item 61): Material-No. / Art.-No.
Ball Ball Ø [mm] 6 6 6 6 6 6 6
1.4401 510.0104.0000 510.0104.0000 510.0104.0000 510.0104.0000 510.0104.0000 510.0104.0000 510.0104.0000
Split ring (item 14): Material-No. / Art.-No.
Split ring Spindle Ø [mm] 12 12 12 12 12 12 12
1.4404 251.0149.0000 251.0149.0000 251.0149.0000 251.0149.0000 251.0149.0000 251.0149.0000 251.0149.0000
Pin (item 57) Material-No. / Art.-No.
Pin 1.4310 480.0505.0000 480.0505.0000 480.0505.0000 480.0505.0000 480.0505.0000 480.0505.0000 480.0705.0000
O-ring damper Material-No. / Art.-No.
Conversion kit H2 5021.1060 5021.1060 – 5021.1060 5021.1060 5021.1060 5021.1060
Conversion kit H4 5021.1064 5021.1064 – 5021.1064 5021.1064 5021.1064 5021.1064

1)
Pressure range, refer to page 01/10 – 01/11

A conversion kit includes the following components:

Item. Components No.

8 Guide with bushing 1

11 Bonnet spacer 1
12 Spindle 1
15 Bellows 1
55 Stud 4, 8 dependant on valve size
60 Gasket 2, 3 dependant on valve size
Installation instruction LWN 037.05 1

Refer to page 01/04

01/16 LWN 485.01-E

Type 431, 433
Order information – spare parts

Spare parts
DNI 65 80 100 125 150
DNO 65 80 100 125 150
Actual orifice diameter d0 [mm]] 37 46 60 74 92
Actual orifice area A0 [mm2] 1075 1662 2827 4301 6648
Disc (item 7): Metal to metal seat Material-No. / Art.-No.

Type 433
Disc 1.4122 220.0339.9000 210.9639.9000 220.2539.9000 220.2639.9000 220.2739.9000
Detachable lifting aid 1.4404 220.0349.9000 210.9649.9000 220.2549.9000 – –
Disc (item 7): Soft seal Material-No. / Art.-No.
Disc CR "K" 200.6349.9051 200.6449.9051 200.6549.9051 200.6649.9051 –
EPDM "D" 200.6349.9041 200.6449.9041 200.6549.9041 200.6649.9041 200.6749.9041
FKM "L" 200.6349.9071 200.6449.9071 200.6549.9071 200.6649.9071 –
FFKM "C" 200.6349.9091 200.6449.9091 – – –
O-ring (item 7.4): Soft seal Material-No. / Art.-No.
O-Ring CR "K" 502.0408.3551 502.0503.3551 502.0660.5351 502.0819.5351 –
EPDM "D" 502.0408.3541 502.0503.3541 502.0660.5341 502.0819.5341 502.1041.5341
FKM "L" 502.0408.3571 502.0503.3571 502.0660.5371 502.0819.5371 –
FFKM "C" 502.0408.3591 502.0503.3591 – – –
Bellows (item 15): 1.4571 Material-No. / Art.-No.
Standard bellows 400.0149.0000 400.0549.0000 400.0649.0000 400.0749.0000 400.0849.0000
Conversion kit, standard1) 5021.1037 5021.1038 5021.1039 Component parts Component parts
Low pressure bellows 400.0449.0021 400.0549.0021 400.0649.0021 400.1107 400.0849.0021
1)
Conversion kit low pressure Please specify application conditions – –
Gasket – body / bonnet (item 60) Material-No. / Art.-No.
Gasket Graphite + 1.4401 500.0907.0000 500.1007.0000 500.1507.0000 500.1807.0000 500.2107.0000
Option code L68 Gylon (PTFE compliance) 500.0905.0000 500.1005.0000 500.1505.0000 500.1805.0000 500.2105.0000
Ball (item 61): Material-No. / Art.-No.
Ball Ball Ø [mm] 9 9 12 12 15
1.4404 510.0204.0000 510.0204.0000 510.0304.0000 510.0304.0000 510.0404.0000
Split ring (item 14): Material-No. / Art.-No.
Split ring Spindle Ø [mm] 16 16 16 20 24
1.4404 251.0249.0000 251.0249.0000 251.0249.0000 251.0349.0000 251.0449.0000
Pin (item 57) Material-No. / Art.-No.
Pin 1.4310 480.0705.0000 480.0705.0000 480.1005.0000 480.1005.0000 480.1105.0000
O-ring damper Material-No. / Art.-No.
Conversion kit H2 5021.1061 5021.1061 – – –
Conversion kit H4 5021.1065 5021.1065 – – –

1)
Pressure range, refer to page 01/10 – 01/11

A conversion kit includes the following components:

Item. Components No.

8 Guide with bushing 1

11 Bonnet spacer 1
12 Spindle 1
15 Bellows 1
55 Stud 4, 8 dependant on valve size
60 Gasket 2, 3 dependant on valve size
Installation instruction LWN 037.05 1

Refer to page 01/04

LWN 485.01-E 01/17

 Type 431, 433
Available options For more information, also see
“Accessories and Options” as of page 99/01.

Heating jacket Drain hole Open bonnet

H29, H30: Coupling G 3/8, G 3/4 J18: G 1/4 See Art.-No.
H31, H32: Flange DN15, DN25 J19: G 1/2
Type 433

O-ring disc Disc with sealing plate Balanced bellows Conversion kit for
J20: FFKM "C" J68: Open bonnet J68: Open bonnet balanced bellows bellows
J21: CR "K" J78: Closed bonnet J78: Closed bonnet Art.-No. see page 01/14
J22: EPDM "D"
J23: FKM "L"

Screwed cap H2 Plain lever H3 Packed lever H4

H2 H3 H4

O-ring damper H2 O-ring damper H4 Lift indicator Test gag

J65 J66 J39: Adaptor H4 J69: H4
J93: Lift indicator J70: H4

01/18 LWN 485.01-E

Type 431, 433
Capacities – steam

Calculation of the capacity for saturated steam acc. to AD 2000-Merkblatt A2 with 10% overpressure.
Capacities at 1 bar and lower are calculated at 0.1 bar overpressure.

Metric units AD 2000-Merkblatt A2 [kg/h]

O-ring Metal
disc disc
DNI 15 15 20 25 32 40 50 65 80 100 125 150
DNO 15 15 20 25 32 40 50 65 80 100 125 150

Type 433
Actual orifice diameter
12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
LEOS/G*) [inch2] 0.106 0.111 0.117 0.154 0.154 0.251 0.399 0.650 1.004 1.708 2.598 4.016
Set pressure [bar] Capacity [kg/h]
0.2 34 34 55 88 142 220 375 570 880
0.5 52 55 30 63 63 102 163 265 410 697 1060 1638
1 74 78 67 101 101 165 263 428 661 1125 1711 2645
2 118 125 129 170 170 278 442 720 1113 1893 2880 4452
3 161 168 177 232 232 379 603 981 1517 2581 3926 6068
4 200 210 221 290 290 473 752 1224 1892 3218 4895 7567
5 251 265 347 347 566 900 1465 2265 3853 5861 9058
6 293 308 404 404 659 1048 1706 2636 4485 6823 10545
7 333 350 459 459 750 1192 1940 2999 5102 7761 11996
8 374 394 516 516 842 1339 2179 3368 5730 8717 13473
9 415 437 572 572 934 1485 2418 3737 6358 9671 14948
10 456 480 629 629 1026 1632 2656 4105 6984 10624 16421
12 538 566 741 741 1210 1924 3132 4842 8237 12530 19366
14 618 650 852 852 1391 2211 3599 5563 9464 14395 22250
16 699 736 964 964 1574 2503 4074 6297 10714 16296 25189
18 781 822 1077 1077 1758 2795 4550 7033 11965 18200 28131
20 863 908 1190 1190 1942 3088 5027 7770 13218 20107
22 942 991 1299 1299 2121 3372 5489 8484 14434 21956
24 1024 1078 1412 1412 2306 3665 5967 9222 15690 23866
26 1106 1164 1525 1525 2491 3959 6445 9962 16949
28 1189 1251 1639 1639 2676 4254 6925 10704 18211
30 1271 1338 1753 1753 2862 4550 7407 11449 19478
32 1354 1425 1867 1867 3049 4847 7890 12195 20748
34
36
38
40
)
* LEOS/G = LESER Effective Orifice steam/gases please refer to page 00/11
“How to use” capacity tables, refer to page 00/09

LWN 485.01-E 01/19

 Type 431, 433
Capacity table – air

Calculation of the capacity for air acc. to AD 2000-Merkblatt A2 with 10% overpressure.
Capacities at 1 bar and lower are calculated at 0.1 bar overpressure.

Metric units AD 2000-Merkblatt A2 [mn3/h]

O-ring Metal
disc disc
DNI 15 15 20 25 32 40 50 65 80 100 125 150
DNO 15 15 20 25 32 40 50 65 80 100 125 150
Type 433

Actual orifice diameter

12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
LEOS/G*) [inch2] 0.106 0.111 0.117 0.154 0.154 0.251 0.399 0.650 1.004 1.708 2.598 4.016
Set pressure [bar] Capacity [mn3/h]
0.2 39 39 63 101 165 255 431 660 1019
0.5 64 67 35 74 74 120 191 311 481 819 1245 1925
1 93 93 80 121 121 197 313 510 788 1341 2039 3152
2 151 151 156 206 206 336 534 870 1344 2287 3478 5377
3 206 206 217 284 284 463 737 1199 1854 3153 4797 7414
4 246 258 272 356 356 582 925 1505 2327 3958 6021 9306
5 296 311 327 429 429 700 1113 1811 2800 4763 7245 11198
6 346 363 382 501 501 818 1301 2117 3273 5568 8469 13091
7 396 416 438 574 574 936 1489 2423 3746 6373 9694 14983
8 446 468 493 646 646 1055 1677 2729 4219 7177 10918 16875
9 496 521 548 718 718 1173 1865 3035 4692 7982 12142 18767
10 546 573 604 791 791 1291 2053 3342 5165 8787 13366 20659
12 646 679 714 936 936 1528 2429 3954 6111 10397 15815 24444
14 746 784 825 1081 1081 1764 2805 4566 7057 12006 18263 28228
16 846 889 935 1225 1225 2001 3181 5178 8003 13616 20711 32013
18 946 994 1046 1370 1370 2237 3557 5790 8949 15226 23160
20 1046 1099 1156 1515 1515 2474 3933 6402 9895 16835 25608
22 1146 1204 1267 1660 1660 2710 4309 7014 10842 18445 28057
24 1245 1309 1377 1805 1805 2947 4685 7626 11788 20055 30505
26 1345 1414 1488 1950 1950 3183 5061 8238 12734 21664 32954
28 1445 1519 1599 2095 2095 3420 5437 8851 13680 23274 35402
30 1545 1624 1709 2240 2240 3656 5813 9463 14626 24883 37850
32 1645 1729 1820 2384 2384 3893 6189 10075 15572 40299
34 1745 1834 1930 2529 2529 4130 6565 10687 16518
36 1845 1939 2041 2674 2674 4366 6941 11299
38 1945 2044 2151 2819 2819 4603 7317 11911
40 2045 2149 2262 2964 2964 4839 7693 12523
)
* LEOS/G = LESER Effective Orifice steam/gases please refer to page 00/11
“How to use” capacity tables, refer to page 00/09

01/20 LWN 485.01-E

Type 431, 433
Capacity table – water

Calculation of the capacity for water acc. to AD 2000-Merkblatt A2 with 10% overpressure at 20 °C.
Capacities at 1 bar and lower are calculated at 0.1 bar overpressure.

Metric units AD 2000-Merkblatt A2 [103kg/h]

O-ring Metal
disc disc
DNI 15 15 20 25 32 40 50 65 80 100 125 150
DNO 15 15 20 25 32 40 50 65 80 100 125 150

Type 433
Actual orifice diameter
12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
LEOL*) [inch2] 0.127 0.129 0.115 0.152 0.152 0.248 0.394 0.641 0.991 1.686 2.564 3.963
Set pressure [bar] Capacity [103kg/h]
0.2 1.77 1.77 2.89 4.60 7.50 11.6 19.7 30.0 46.3
0.5 2.09 2.14 1.90 2.51 2.51 4.09 6.51 10.6 16.4 27.8 42.4 65.5
1 2.84 2.90 2.58 3.39 3.39 5.54 8.81 14.3 22.2 37.7 57.4 88.7
2 4.01 4.10 3.65 4.80 4.80 7.84 12.5 20.3 31.3 53.3 81.1 125
3 4.91 5.02 4.47 5.88 5.88 9.60 15.3 24.8 38.4 65.3 99.3 154
4 5.67 5.79 5.16 6.79 6.79 11.1 17.6 28.7 44.3 75.4 115 177
5 6.34 6.48 5.77 7.59 7.59 12.4 19.7 32.1 49.6 84.3 128 198
6 6.95 7.09 6.32 8.31 8.31 13.6 21.6 35.1 54.3 92.4 140 217
7 7.50 7.66 6.82 8.98 8.98 14.7 23.3 37.9 58.6 99.8 152 235
8 8.02 8.19 7.30 9.60 9.60 15.7 24.9 40.6 62.7 107 162 251
9 8.51 8.69 7.74 10.2 10.2 16.6 26.4 43.0 66.5 113 172 266
10 8.97 9.16 8.16 10.7 10.7 17.5 27.9 45.3 70.1 119 181 280
12 9.82 10.0 8.93 11.8 11.8 19.2 30.5 49.7 76.8 131 199 307
14 10.6 10.8 9.65 12.7 12.7 20.7 33.0 53.7 82.9 141 215 332
16 11.3 11.6 10.3 13.6 13.6 22.2 35.2 57.4 88.7 151 229 355
18 12.0 12.3 10.9 14.4 14.4 23.5 37.4 60.8 94.0 160 243
20 12.7 13.0 11.5 15.2 15.2 24.8 39.4 64.1 99.1 169 257
22 13.3 13.6 12.1 15.9 15.9 26.0 41.3 67.3 104 177 269
24 13.9 14.2 12.6 16.6 16.6 27.1 43.2 70.2 109 185 281
26 14.5 14.8 13.2 17.3 17.3 28.3 44.9 73.1 113 192 292
28 15.0 15.3 13.6 18.0 18.0 29.3 46.6 75.9 117 200 304
30 15.5 15.9 14.1 18.6 18.6 30.3 48.2 78.5 121 207 314
32 16.0 16.4 14.6 19.2 19.2 31.3 49.8 81.1 125 324
34 16.5 16.9 15.0 19.8 19.8 32.3 51.4 83.6 129
36 17.0 17.4 15.5 20.4 20.4 33.2 52.9 86.0
38 17.5 17.9 15.9 20.9 20.9 34.2 54.3 88.4
40 17.9 18.3 16.3 21.5 21.5 35.0 55.7 90.7

*) LEOL = LESER Effective Orifice liquids, please refer to page 00/11

“How to use” capacity tables, refer to page 00/09

LWN 485.01-E 01/21

 Type 431, 433
h = Lift [mm]
Determination of coefficient of discharge d0 = Flow diameter [mm] of selected safety
in case of lift restriction or back pressure valve see “Article Numbers” table
h/d0 = Ratio of lift / flow diameter
pa0 = Back pressure [bara]
p0 = Set pressure [bara]
pa0/p0 = Ratio of back pressure / set pressure
Kdr = Coefficient of discharge
acc. to DIN EN ISO 4126-1
αw = Coefficient of discharge
acc. to AD 2000-Merkblatt A2
Kb = Back pressure correction factor
acc. to API 520 Section 3.3

“How to use” refer to page 00/08

Diagram for evaluation of ratio of lift / flow diameter (h/d0) in reference
to the coefficient of discharge (Kdr /αw)
Type 433

Kdr = αw = f (h/d0) Only valid for “steam/gases” Kdr = αw = f (h/d0) Only valid for “liquids”
0.8 0.8

0.7 0.7

DN15, Metal disc, S/G

0.6 0.6

0.5 0.5
DN15, Metal disc, L

0.4 0.4
Coefficient of discharge Kdr / αw

Coefficient of discharge Kdr / αw

DN25 – DN150, S/G DN15, O-ring-disc, L

DN15, O-ring-disc, S/G

0.3 0.3
DN25 – DN150, L

0.2 0.2
DN20, L

0.1 DN20, S/G 0.1

0 0
0 0.1 0.2 0.3 0 0.1 0.2 0.3
0.110 0.208 0.110 0.208
Ratio of lift / flow diameter h / d0 Ratio of lift / flow diameter h / d0

Diagram for evaluation of coefficient of discharge (Kdr /αw) or Kb in reference

to the ratio of back pressure / set pressure (pa0 / p0)

Kdr = αw = f (pa0/p0)
0.8

0.7
DN15 Metal disc

0.6

DN15 O-ring-disc
0.5

DN25 – 150
0.4
Coefficient of discharge Kdr / αw

0.3

0.2
DN20

0.1

0
0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900
0.833
Ratio of back pressure / set pressure pa0 / p0

01/22 LWN 485.01-E

 Type 431 PN 160
Packed lever H4
Open bonnet
Conventional design
Type
431, 433
PN 160
Flanged Safety Relief Valves
- spring loaded

Contents Chapter/Page

Type 433 PN 160

Materials
• Conventional design 02/02
• Balanced bellows design 02/04
How to order
• Numbering system 02/06
• Article numbers 02/08
Pressure temperature ratings
Type 433 PN 160 • Metric units 02/09
Cap H2 Dimensions and weights
Closed bonnet
• Metric units 02/10
Conventional design
Flange drillings and Flange facings 02/11
Order information - spare parts 02/12
Available options 02/13
Approvals 02/14
Capacities
• Steam [Metric units] 02/15
• Air [Metric units] 02/15
• Water [Metric units] 02/15
Determination of 02/16
coefficient of discharge Kdr /α w

LWN 485.01-E 02/01

 Type 431, 433 PN 160
Conventional design

40 Cap H2

18 Adjusting screw with bushing

19 Lock nut

16 Upper spring plate

12 Spindle

9 Bonnet
Type 433 PN 160

54 Spring

14 Split ring

17 Lower spring plate

55 Stud

56 Nut

60 Gasket

8 Guide

57 Pin

61 Ball

7 Disc

5 Seat

6 Seat screw

1 Body

02/02 LWN 485.01-E

Type 431, 433 PN 160
Conventional design

Materials
O-ring disc Metal disc O-ring disc Metal disc

Item Component Type 4312 / 4332 Type 4312 / 4332 Type 4334 Type 4334

1.0619 1.0619 1.4408 1.4408

1 Body
SA 216 WCB SA 216 WCB SA 351 CF8M SA 351 CF8M
1.4404 1.4404 1.4404 1.4404
5 Seat
316L 316L 316L 316L
1.4404 1.4404 1.4404 1.4404
6 Seat screw
316L 316L 316L 316L
1.4404 1.4122 1.4404 1.4404
7 Disc
316L Hardened stainless steel 316L 316L
1.4104 tenifer 1.4104, 1.0501, 1.0570 1.4404 1.4404
8 Guide
Chrome steel tenifer Chrome or stainless steel 316L 316L
0.7040 0.7040 1.4408 1.4408
9 Bonnet
Ductile Gr. 60-40-18 Ductile Gr. 60-40-18 SA 351 CF8M SA 351 CF8M
1.4021 1.4021 1.4404 1.4404
12 Spindle

Type 433 PN 160

420 420 316L 316L
1.4104 1.4104 1.4404 1.4404
14 Split ring
Chrome steel Chrome steel 316L 316L
1.0718 1.0718 1.4404 1.4404
16/17 Spring plate
Steel Steel 316L 316L
Adjusting screw 1.4104 PTFE 1.4104 PTFE 1.4404 PTFE 1.4404 PTFE
18
with bushing Chrome steel PTFE Chrome steel PTFE 316L PTFE 316L PTFE
1.4104 1.4104 1.4404 1.4404
19 Lock nut
Chrome steel Chrome steel 316L 316L
1.0718 1.0718 1.4404 1.4404
40 Cap H2
12L13 12L13 316L 316L
1.1200, 1.8159, 1.7102 1.1200, 1.8159, 1.7102 1.4310 1.4310
Spring, standard
Steel Steel Stainless steel Stainless steel
54
1.4310 1.4310 – –
Spring, optional
Stainless steel Stainless steel – –
1.1181 1.1181 1.4401 1.4401
55 Stud
Steel Steel B8M B8M
1.0501 1.0501 1.4401 1.4401
56 Nut
2H 2H 8M 8M
1.4310 1.4310 1.4310 1.4310
57 Pin
Stainless steel Stainless steel Stainless steel Stainless steel
Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401
60 Gasket
Graphite / 316 Graphite / 316 Graphite / 316 Graphite / 316
1.3541 1.3541 1.4401 1.4401
61 Ball
Hardened stainless steel Hardened stainless steel 316 316
Note:

– LESER reserves the right to make changes.

– If several materials are specified LESER defines the material.
– LESER may use higher quality materials without giving prior notice.
– Each component can be constructed of another material according to the customer's specification.
– All components exposed to pressure are highlighted in bold. The material will be specified according to DIN and ASTM here.

LWN 485.01-E 02/03

 Type 431, 433 PN 160
Balanced bellows design

40 Cap H2

18 Adjusting screw with bushing

19 Lock nut

16 Upper spring plate

12 Spindle

9 Bonnet

54 Spring
Type 433 PN 160

14 Split ring

17 Lower spring plate

55 Stud

56 Nut

60 Gasket

8 Guide

11 Bonnet spacer

15 Balanced bellows

60 Gasket

57 Pin

61 Ball

7 Disc

5 Seat

6 Seat screw

1 Body

02/04 LWN 485.01-E

Type 431, 433 PN 160
Balanced bellows design

Materials
O-ring disc Metal disc O-ring disc Metal disc

Item Component Type 4312 / 4332 Type 4312 / 4332 Type 4334 Type 4334

1.0619 1.0619 1.4408 1.4408

1 Body
SA 216 WCB SA 216 WCB SA 351 CF8M SA 351 CF8M
1.4404 1.4404 1.4404 1.4404
5 Seat
316L 316L 316L 316L
1.4404 1.4404 1.4404 1.4404
6 Seat screw
316L 316L 316L 316L
1.4404 1.4122 1.4404 1.4404
7 Disc
316L Hardened stainless steel 316L 316L
Guide 1.4404 1.4404 1.4404 1.4404
8 Upper connection of
balanced bellows 316L 316L 316L 316L
0.7040 0.7040 1.4408 1.4408
9 Bonnet
Ductile Gr. 60-40-18 Ductile Gr. 60-40-18 SA 351 CF8M SA 351 CF8M

Type 433 PN 160

1.4404 1.4404 1.4404 1.4404
11 Bonnet spacer
316L 316L 316L 316L
1.4404 1.4404 1.4404 1.4404
12 Spindle
316L 316L 316L 316L
1.4104 1.4104 1.4404 1.4404
14 Split ring
Chrome steel Chrome steel 316L 316L
1.4571 1.4571 1.4571 1.4571
15 Balanced bellows
316Ti 316Ti 316Ti 316Ti
1.0718 1.0718 1.4404 1.4404
16/17 Spring plate
Steel Steel 316L 316L
Adjusting screw 1.4104 PTFE 1.4104 PTFE 1.4404 PTFE 1.4404 PTFE
18
with bushing Chrome steel PTFE Chrome steel PTFE 316L PTFE 316L PTFE
1.4104 1.4104 1.4404 1.4404
19 Lock nut
Chrome steel Chrome steel 316L 316L
1.0718 1.0718 1.4404 1.4404
40 Cap H2
12L13 12L13 316L 316L
1.1200, 1.8159, 1.7102 1.1200, 1.8159, 1.7102 1.4310 1.4310
Spring, standard
Steel Steel Stainless steel Stainless steel
54
1.4310 1.4310 – –
Spring, optional
Stainless steel Stainless steel – –
1.4401 1.4401 1.4401 1.4401
55 Stud
8M 8M B8M B8M
1.4401 1.4401 1.4401 1.4401
56 Hex nut
8M 8M B8M B8M
1.4310 1.4310 1.4310 1.4310
57 Roll pin
Stainless steel Stainless steel Stainless steel Stainless steel
Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401
60 Gasket
Graphite / 316 Graphite / 316 Graphite / 316 Graphite / 316
1.3541 1.3541 1.4401 1.4401
61 Ball
Hardened stainless steel Hardened stainless steel 316 316
Note:

– LESER reserves the right to make changes.

– If several materials are specified LESER defines the material.
– LESER may use higher quality materials without giving prior notice.
– Each component can be constructed of another material according to the customer’s specification.
– All components exposed to pressure are highlighted in bold. The material will be specified according to DIN and ASTM here.

LWN 485.01-E 02/05

 Type 431, 433 PN 160
How to order – Example for numbering system – Type 433 PN 160

1 Article Number
2 Set Pressure
3 Connections

4332.8552 60 bar H47

1 2 3 4 Please enter the units (in gauge)! Please refer to page 02/11.

433 2 . 855 2 The specified pressure range may

not be exceeded!
1 Valve type 431, 433 PN 160
Type 433 – with closed bonnet
Type 431 – with open bonnet
Type 433 PN 160

2 Material code

Code Body material

2 1.0619 (WCB)
4 1.4408 (CF8M)

3 Valve code
Automatically determines
nominal diameter and
body material (see page 02/08).

Code Lifting device

2 Gas-tight cap H2
3 Plain lever H3
4 Packed lever H4
Plain lever with
5 H3
open bonnet

02/06 LWN 485.01-E

Type 431, 433 PN 160

4 Options
5 Documentation
6
Code and Medium

J22 H01 L30 2.0

Type 431, 433 PN 160 Option code Please select the necessary
1 2
documentation:
• O-ring disc
CR “K” J21
Tests, Certifications: Option code 2 . 0
DIN EN 10204-3.2: TÜV-Nord
EPDM “D” J22
Certification for set pressure M33 1 Code
FKM “L” J23
FFKM “C” J20 2. CE / VdTUEV
LESER CGA (Certificate H03 3. ASME Section VIII
• Disc 1.4404 / 316L L44
for Global Application) + CE / VdTUEV
• Disc 1.4404 / 316L stellited J25

Type 433 PN 160

- Acceptance test certificate 3.1
• Detachable lifting aid J26
acc. to DIN EN 10204 2 Medium
• Balanced bellows - Declaration of conformity as per .0 steam / gases / liquids
- Bonnet, open (Type 431) J68 pressure equipment directive
- Bonnet, closed (Type 433) J78 (only valid for CE / VdTUEV)
PED 97/23/EC
• High temperature alloy spring X01
• Stainless steel spring X04 Material quality certificate:
• Adaptor for lift indicator H4 J39 DIN EN 10204-3.1
• Lift indicator J93
• Test gag Component Option code
- Cap H2 J70 Body H01
- Packed lever H4 J69 Nozzle L59
• Heating jacket Bonnet L30
- Couplings G 3/8 H29 Disc L23
G 3/4 H30 Screws N07
- Flange DN 15 H31 Nuts N08
DN 25 H32
• Heating jacket - H33
Bonnet spacer
• Drain hole G 1/4 J18
G 1/2 J19
• Oil and grease free J85
• Materials
- NACE N78

Option code applies

only if not standard

LWN 485.01-E 02/07

 Type 431, 433 PN 160
How to order – article numbers

Article numbers
O-ring disc Metal disc
DNI 15 15
DNO 25 25
Actual orifice diameter
12 12
d0 [mm]
Actual orifice area
113 113
A0 [mm2]
Body material: 1.0619 (WCB)
Bonnet H2 Art.-No. 4332. 8572 8552
closed H3 Art.-No. 4332. 8573 8553
H4 Art.-No. 4332. 8574 8554
open H3 Art.-No. 4312. 8575 8555
Body material: 1.4408 (CF8M)
Bonnet H2 Art.-No. 4334. 8582 8562
closed H4 Art.-No. 4334. 8584 8564
Type 433 PN 160

Type 433 PN 160 Type 433 PN 160

Cap H2 Plain lever H3
Closed bonnet Closed bonnet
Conventional design Conventional design

Type 433 PN 160

Packed lever H4
Closed bonnet
Conventional design

Type 431 PN 160 Type 431 PN 160

Plain lever H3 Plain lever H3
Open bonnet Closed bonnet
Conventional design Balanced bellows design

02/08 LWN 485.01-E

Type 431, 433 PN 160
Pressure temperature ratings

Metric units
O-ring disc Metal disc
DNI 15 15
DNO 25 25
Actual orifice diameter
12 12
d0 [mm]
Actual orifice area
113 113
A0 [mm2]
Body material: 1.0619 (WCB)
DIN flange Inlet PN 160
Outlet PN 40
Minimum set pressure
p [barg] S/G/L 0.3 0.3

Min. set pressure1)

standard bellows p [barg] S/G/L 3 3

Maximum set pressure “K”

p [barg] S/G/L “D” 142 “C” 85 144
“L”

433 PN 160
Max. set pressure “K”
with special spring p [barg] S/G/L “D” 160 “C” 85 160
“L”
Temperature2) min. [°C] -45 -60
acc. to DIN EN max. [°C] +150 +450

Body material: 1.4408 (CF8M)

DIN flange Inlet PN 160
Outlet PN 40
Minimum set pressure
p [barg] S/G/L 0.3 0.3

Min. set pressure1)

standard bellows p [barg] S/G/L 3 3

Max. set pressure

p [barg] S/G/L 85 85

Max. set pressure “K”

with special spring p [barg] S/G/L “D” 150 “C” 85 160
“L”
Temperature2) min. [°C] -45 -270
acc. to DIN EN max. [°C] +150 +400

1)
Min. set pressure of standard bellows = max. set pressure of bellows for low set pressure.
2)
The temperature is limited by the soft seal material (see page 99/10). The values given here are valid for EPDM.
Between -10°C and the lowest specified application temperature, proceed as per AD 2000-Merkblatt W10.

LWN 485.01-E 02/09

 Type 431, 433 PN 160
Dimensions and weights

Metric units
DNI 15
DNO 25
Actual orifice diameter
12
d0 [mm]
Actual orifice area
113
A0 [mm2]

Weight 7
[kg] with bellows 8.4
Centre to face Inlet a 90
[mm] Outlet b 90
Height (H4) Standard H max. 307
[mm] Bellows H max. 359

Body material: 1.0619 (WCB)

DIN flange1) Inlet PN 160
Outlet PN 40
Body material: 1.4408 (CF8M)
DIN flange1) Inlet PN 160
Outlet PN 40
Type 433 PN 160

1)
Standard flange class. For other flange drillings, see page 02/11.

Conventional design Balanced bellows design

02/10 LWN 485.01-E

Type 431, 433 PN 160
Flange drillings and facings

Flange drillings
DNI 15
DNO 25
Valve size 1/
2" x 1"

Actual orifice diameter

12
d0 [mm]
Actual orifice area
113
A0 [mm2]
Body material: 1.0619 (WCB), 1.4408 (CF8M)
PN 16 H47
PN 40 H47
Inlet DIN EN 1092
PN 63 *
PN 160 *
CL300 H65
ASME B 16.5
CL600 H67
PN 16 *
DIN EN 1092
PN 40 *
Outlet
CL150 H79
ASME B16.51)
CL300 H80

Flange facings

Type 433 PN 160

Information Standard Inlet Outlet Remark
General
Flange, undrilled – H38 H39
Linde-V-Nut, Form V48 Linde Standard 420-08 J07 J08 Groove: Rz = 16
Linde-V-Nut, Form V48A LWN 313.36 J05 J06 Groove: Rz = 4, e.g. for hydrogen
Lens-shape seal form L DIN 2696
J11 J12
(without lens-shape seal) LWN 313.35
According to DIN EN 1092
Flange facings Remark
Inlet Outlet
DIN EN 1092 Rz specification
(also see LWN 313.40) PN 63 – acc. to DIN EN 1092 in µm
PN 40
PN 160

Form B1 – Seal. strip.: Rz = 12.5 – 50

Sealing strip *
Form B2 L38 Seal. strip.: Rz = 3.2 – 12.5
*
only for steel flange

Tongue, Form C1) H94 H92

Groove, Form D1) H93 H91
Male, Form E H96 H98
Female, Form F H97 H99
O-ring Male, Form G J01 J02
O-ring Female, Form H J03 J04
According to ASME B16.5
Smooth Finish2) Serrated Finish RTJ-Groove

Body material Inlet Outlet Inlet Outlet Inlet Outlet Inlet Outlet
Pressure Pressure
Option code Option code Option code Option code
level level

1.0619, 1.4408 all all L52 L53 CL150 H62 CL150 H63
* *
1)
LESER manufactures the groove at flanged valves by milling. If a customer demands a turned surface in the soil of the groove according to DIN EN 1092-1
an additional option code is necessary: “S01: soil of the groove drilled”.
2)
Smooth Finish is not defined in the effective standards.

For signs and symbols refer to page 00/07

Note: Flange drillings and facings meet always the requirements of mentioned flange standards.
Flange thickness and outer diameter may vary from flange standard.

LWN 485.01-E 02/11

 Type 431, 433 PN 160
Order information – spare parts

Spare parts
O-ring disc Metal disc
DNI 15 15
DNO 25 25
Actual orifice diameter
12 12
d0 [mm]
Actual orifice area
113 113
A0 [mm2]
Disc (item 7): Metal seat Material-No. / Art.-No.
Disc 1.4122 – 230.9339.9000
Detachable lifting aid 1.4404 – 230.9349.9000
Disc (item 7): Soft seal Material-No. / Art.-No.
Disc CR “K” 230.2949.9053 –
EPDM “D” 230.2949.9042 –
FKM “L” 230.2949.9073 –
FFKM “C” 230.2949.9091 –
O-ring (item 7.4): Soft seal Material-No. / Art.-No.
O-Ring CR “K” 502.0107.2653 –
EPDM “D” 502.0107.2642 –
Type 433 PN 160

FKM “L” 502.0107.2673 –

FFKM “C” 502.0107.2691 –
Bellows (item 15): 1.4571 Material-No. / Art.-No.
Standard bellows 400.6349.0000 400.6349.0000
Conversion kit, standard1) Please specify application conditions
Low pressure bellows – –
Conversion kit low pressure1) – –
Gasket – body / bonnet (item 60) Material-No. / Art.-No.
Gasket Graphite + 1.4401 500.0407.0000 500.0407.0000
Option code L68 Gylon (PTFE compliance) 500.0405.0000 500.0405.0000
Ball (item 61): Material-No. / Art.-No.
Ball Ball Ø [mm] 6 6
1.4404 510.0104.0000 510.0104.0000
Split ring (item 14): Material-No. / Art.-No.
Split ring Spindle Ø [mm] 12 12
1.4404 251.0149.0000 251.0149.0000
Pin (item 57) Material-No. / Art.-No.
Pin 1.4310 480.0505.0000 480.0505.0000
O-ring damper Material-No. / Art.-No.
Conversion kit H2 5021.1060 5021.1060
Conversion kit H4 5021.1064 5021.1064

Item. Components No.

8 Guide; upper connection of balanced bellows 1

11 Bonnet spacer 1
12 Spindle 1
15 Bellows 1
55 Stud 4
60 Gasket 2
Instruction guide LWN 037.05 1
Refer to page page 02/04

02/12 LWN 485.01-E

Type 431, 433 PN 160
Available options For more information, also see
“Accessories and Options” as of page 99/01.

Heating jacket Drain hole Open bonnet

H29, H30: Coupling G 3/8, G 3/4 J18: G 1/4 See Art.-No.
H31, H32: Flange DN15, DN25 J19: G 1/2

O-ring disc Balanced bellows Conversion kit for

J20: FFKM “C” J68: Open bonnet balanced bellows
J21: CR “K” J78: Closed bonnet Art.-No. see page 02/14
J22: EPDM “D”
J23: FKM “L”

Type 433 PN 160

Screwed cap H2 Plain lever H3 Packed lever H4
H2 H3 H4

O-ring damper H2 O-ring damper H4 Lift indicator Test gag

J65 J66 J39: Adaptor H4 J69: H4
J93: Lift indicator J70: H4

LWN 485.01-E 02/13

 Type 431, 433 PN 160
Approvals

Approvals
O-ring disc Metal disc
DNI 15 15
DNO 25 25
Actual orifice diameter d0 [mm] 12 12
Actual orifice area A0 [mm2] 113 113
Europe Coefficient of discharge Kdr
PED / DIN EN ISO 4126-1 Approval-No. 072020111Z0008/0/06
S/G 0.59 0.62
L 0.47 0.48
Germany Coefficient of discharge α w
PED / AD 2000-Merkblatt A2 Approval-No. TÜV SV 577
Standard safety valve S/G 0.59 0.62
L 0.47 0.48
China Coefficient of discharge K
AQSIQ Approval-No. For current Approval-No. see www.leser.com
S/G 0.59 0.62
Type 433 PN 160

L 0.47 0.48
Russia Coefficient of discharge K
TR/ RTN Approval-No. For current Approval-No. see www.leser.com
S/G 0.59 0.62
L 0.47 0.48
Kazakhstan Coefficient of discharge α w
GOST-K Approval-No. For current Approval-No. see www.leser.com
S/G 0.59 0.62
L 0.47 0.48
Belarus Coefficient of discharge α w
GOSPROMNAZADOR Approval-No. For current Approval-No. see www.leser.com
S/G 0.59 0.62
L 0.47 0.48

Classification societies Homepage

Bureau Veritas BV www.bureauveritas.com
The valid Approval-No. changes
ClassNK NIPPON Kaiji Kyokai NK www.classnk.or.jp with each renewal of the approval.
Det Norske Veritas DNV www.dnv.com
Germanischer Lloyd GL www.gl-group.com For a sample certificate including
Lloyd‘s Register EMEA LREMEA www.lr.org the valid certification number
see www.leser.com
Registro Italiano Navale RINA www.rina.org

02/14 LWN 485.01-E

Type 431, 433 PN 160
Capacities

Calculation of the capacity for steam, gases, and liquids acc. to AD 2000-Merkblatt A2 with 10% overpressure.
Capacities at 1 bar and lower are calculated at 0.1 bar overpressure.

Metric units AD 2000-Merkblatt A2

O-ring disc Metal disc O-ring disc Metal disc O-ring disc Metal disc
DN 15 15 15 15 15 15
DNO 25 25 25 25 25 25
Actual orifice diameter
12 12 12 12 12 12
d0 [mm]
Actual orifice area
113 113 113 113 113 113
A0 [mm2]
LEOS/G/L*) [inch2] 0.106 0.111 0.106 0.111 0.127 0.129
Set pressure Capacities Capacities Capacities

Steam Air Water

[bar] saturated 0°C and 1013 mbar 20°C
[kg/h] [mn3/h] [103 kg/h]

0.2
0.5 52 55 64 67 2.09 2.14
1 74 78 93 93 2.84 2.90
2 118 125 151 151 4.01 4.10
3 161 168 206 206 4.91 5.02

Type 433 PN 160

4 200 210 246 258 5.67 5.79
5 251 296 311 6.34 6.48
6 293 346 363 6.95 7.09
7 333 396 416 7.50 7.66
8 374 446 468 8.02 8.19
9 415 496 521 8.51 8.69
10 456 546 573 8.97 9.16
12 538 646 679 9.82 10.0
14 618 746 784 10.6 10.8
16 699 846 889 11.3 11.6
18 781 946 994 12.0 12.3
20 863 1046 1099 12.7 13.0
22 942 1146 1204 13.3 13.6
24 1024 1245 1309 13.9 14.2
26 1106 1345 1414 14.5 14.8
28 1189 1445 1519 15.0 15.3
30 1271 1545 1624 15.5 15.9
32 1354 1645 1729 16.0 16.4
34 1433 1745 1834 16.5 16.9
36 1517 1845 1939 17.0 17.4
38 1600 1945 2044 17.5 17.9
40 1684 2045 2149 17.9 18.3
50 2109 2545 2674 20.1 20.5
60 2537 3045 3200 22.0 22.4
70 2981 3545 3725 23.7 24.2
80 3430 4045 4250 25.4 25.9
90 3901 4544 4775 26.9 27.5
100 5044 5301 28.4 29.0
120 6044 6351 31.1 31.7
140 7044 7402 33.6 34.3
160 8043 8452 35.9 36.6

*) LEOS/G/L = LESER Effective Orifice for steam, gases, and liquids, please refer to page 00/11
“How to use” capacity tables, refer to page 00/09

LWN 485.01-E 02/15

 Type 431, 433 PN 160
Determination of coefficient of discharge h = Lift [mm]
d0 = Flow diameter [mm] of selected safety
in case of lift restriction or back pressure valve see “Article Numbers” table
h/d0 = Ratio of lift / flow diameter
pa0 = Back pressure [bara]
p0 = Set pressure [bara]
pa0/p0 = Ratio of back pressure / set pressure
Kdr = Coefficient of discharge
acc. to DIN EN ISO 4126-1
αw = Coefficient of discharge
acc. to AD 2000-Merkblatt A2
Diagram for evaluation of ratio of lift / flow diameter (h/d0) in reference Kb = Back pressure correction factor
to the coefficient of discharge Kdr /αw) acc. to API 520 Section 3.3

"How to use" refer to page 00/08

Kdr = αw = f (h/d0) Only valid for “steam/gases” Kdr = αw = f (h/d0) Only valid for “liquids”
0.8 0.8

0.7 0.7

DN15, Metal disc, S/G

0.6 0.6

0.5 0.5
DN15, Metal disc, L

0.4 0.4
Coefficient of discharge Kdr / αw

DN15, O-ring-disc, L
Coefficient of discharge Kdr / αw

DN15, O-ring-disc, S/G

0.3 0.3
Type 433 PN 160

0.2 0.2

0.1 0.1

0 0
0 0.1 0.2 0.3 0 0.1 0.2 0.3
Ratio of lift / flow diameter h / d0 Ratio of lift / flow diameter h / d0

Diagram for evaluation of coefficient of discharge (Kdr /αw) or Kb in reference

to the ratio of back pressure / set pressure (pa0 / p0)

Kdr = αw = f (pa0/p0)
0.8

0.7
DN15 Metal disc

0.6

DN15 O-ring-disc
0.5

0.4
Coefficient of discharge Kdr / αw

0.3

0.2

0.1

0
0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900

0.717 0.772
Ratio of back pressure / set pressure pa0 / p0

02/16 LWN 485.01-E

 Type 427
Plain lever H3
Open bonnet
Conventional design
Type
427, 429

Flanged Safety Relief Valves

– spring loaded

Contents Chapter/Page
Materials
• Conventional design 03/02
• Balanced bellows design 03/04
How to order
• Numbering system 03/06
• Article numbers 03/08
Pressure temperature ratings
• Metric units 03/10
Type 429 Dimensions and weights
Cap H2 • Metric units 03/12
Closed bonnet
Conventional design Flange drillings and facings 03/13
Order information - spare parts 03/14
Available options 03/16

Type 429
Approvals 03/17
Capacities
• Steam [Metric units] 03/18
• Air [Metric units] 03/19
• Water [Metric units] 03/20

LWN 485.01-E 03/01

 Type 427, 429
Conventional design

40 Cap H2

18 Adjusting screw with bushing

19 Lock nut

16 Upper spring plate

12 Spindle

9 Bonnet

54 Spring

14 Split ring

55 Stud

56 Nut

17 Lower spring plate

60 Gasket
Type 429

8 Guide with bushing

57 Pin

61 Ball

7 Disc

5 Seat

1 Body

03/02 LWN 485.01-E

Type 427, 429
Conventional design

Materials
Item Component Type 4275 / 4295 Type 4272 / 4292 Type 4294

0.7043 1.0619 1.4408

1 Body
Ductile Gr. 60-40-18 SA 216 WCB SA 351 CF8M
1.4404 1.4404 1.4404
5 Seat
316L 316L 316L
1.4122 1.4122 1.4404
7 Disc
Hardened stainless steel Hardened stainless steel 316L
1.4104, 1.0501 1.4104, 1.0501, 1.0570 1.4404
Guide
Chrome steel or steel Chrome steel or steel 316L
8
1.4104 tenifer 1.4104 tenifer –
with bushing
Chrome steel tenifer Chrome steel tenifer –
0.7040 0.7040 1.4408, 1.4404
9 Bonnet
Ductile Gr. 60-40-18 Ductile Gr. 60-40-18 SA 351 CF8M, SA 479 316 L
1.4021 1.4021 1.4404
12 Spindle
420 420 316L
1.4104 1.4104 1.4404
14 Split ring
Chrome steel Chrome steel 316L
1.0718 1.0718 1.4404
16/17 Spring plate
Steel Steel 316L
Adjusting screw 1.4104 PTFE 1.4104 PTFE 1.4404 PTFE
18
with bushing Chrome steel PTFE Chrome steel PTFE 316L PTFE
1.0718 1.0718 1.4404
19 Lock nut
Steel Steel 316L
1.0718 1.0718 1.4404
40 Cap H2
12L13 12L13 316L
1.1200, 1.8159, 1.7102 1.1200, 1.8159, 1.7102 1.4310
Spring, standard
Steel Steel Stainless steel
54
1.4310 1.4310 –
Spring, optional
Stainless steel Stainless steel –
1.1181 1.1181 1.4401
55 Stud
Steel Steel B8M
1.0501 1.0501 1.4401

Type 429
56 Nut
2H 2H 8M
1.4310 1.4310 1.4310
57 Pin
Stainless steel Stainless steel Stainless steel
Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401
60 Gasket
Graphite / 316 Graphite / 316 Graphite / 316
1.3541 1.3541 1.4401
61 Ball
Hardened stainless steel Hardened stainless steel 316
Note:

– LESER reserves the right to make changes.

– If several materials are specified LESER defines the material.
– LESER may use higher quality materials without giving prior notice
– Each component can be constructed of another material according to the customer's specification.
– All components exposed to pressure are highlighted in bold. The material will be specified according to DIN and ASTM here.

LWN 485.01-E 03/03

 Type 427, 429
Balanced bellows design

40 Cap H2

18 Adjusting screw with bushing

19 Lock nut

16 Upper spring plate

12 Spindle

9 Bonnet

54 Spring

14 Split ring

17 Lower spring plate

55 Stud

56 Nut

8 Guide with bushing

60 Gasket

11 Bonnet spacer
Type 429

15 Balanced bellows

60 Gasket

22 Lift stoppers

57 Pin

61 Ball

7 Disc

5 Seat

1 Body

03/04 LWN 485.01-E

Type 427, 429
Balanced bellows design

Materials
Item Component Type 4275 / 4295 Type 4272 / 4292 Type 4294

0.7043 1.0619 1.4408

1 Body
Ductile Gr. 60-40-18 SA 216 WCB SA 351 CF8M
1.4404 1.4404 1.4404
5 Seat
316L 316L 316L
1.4122 1.4122 1.4404
7 Disc
Hardened stainless steel Hardened stainless steel 316L
1.4104, 1.0501 1.4104, 1.0501, 1.0570 1.4404
Guide
Chrome steel or steel Chrome steel or steel 316L
8
1.4104 tenifer 1.4104 tenifer –
with bushing
Chrome steel tenifer Chrome steel tenifer –
0.7040 0.7040 1.4408
9 Bonnet
Ductile Gr. 60-40-18 Ductile Gr. 60-40-18 SA 351 CF8M
1.4404 1.4404 1.4404
11 Bonnet spacer
316L 316L 316L
1.4404 1.4404 1.4404
12 Spindle
316L 316L 316L
1.4104 1.4104 1.4404
14 Split ring
Chrome steel Chrome steel 316L
1.4571 1.4571 1.4571
15 Balanced bellows
316Ti 316Ti 316Ti
1.0718 1.0718 1.4404
16/17 Spring plate
Steel Steel 316L
Adjusting screw 1.4104 PTFE 1.4104 PTFE 1.4404 PTFE
18
with bushing Chrome steel PTFE Chrome steel PTFE 316L PTFE
1.0718 1.0718 1.4404
19 Lock nut
Steel Steel 316L
1.4404 1.4404 1.4404
22 Lift stoppers
316L 316L 316L
1.0718 1.0718 1.4404
40 Cap H2
12L13 12L13 316L
1.1200, 1.8159, 1.7102 1.1200, 1.8159, 1.7102 1.4310

Type 429
Spring, standard
Steel Steel Stainless steel
54
1.4310 1.4310 –
Spring, optional
Stainless steel Stainless steel –
1.4401 1.4401 1.4401
55 Stud
8M B8M B8M
1.4401 1.4401 1.4401
56 Nut
8M B8M B8M
1.4310 1.4310 1.4310
57 Pin
Stainless steel Stainless steel Stainless steel
Graphite / 1.4401 Graphite / 1.4401 Graphite / 1.4401
60 Gasket
Graphite / 316 Graphite / 316 Graphite / 316
1.3541 1.3541 1.4401
61 Ball
Hardened stainless steel Hardened stainless steel 316
Note:

– LESER reserves the right to make changes.

– If several materials are specified LESER defines the material.
– LESER may use higher quality materials without giving prior notice
– Each component can be constructed of another material according to the customer’s specification.
– All components exposed to pressure are highlighted in bold. The material will be specified according to DIN and ASTM here.

LWN 485.01-E 03/05

 Type 427, 429
How to order – Example for numbering system – Type 429

1 Article Number
2 Set Pressure
3 Connections

4292.7172 5 bar H45

1 2 3 4 Please enter the units (in gauge)! Please refer to page 03/13.

429 2 . 717 2 The specified pressure range may

not be exceeded!
1 Valve type 427, 429
Type 429 – with closed bonnet
Type 427 – with open bonnet

2 Material code

Code Body material

2 1.0619 (WCB)
4 1.4408 (CF8M)
0.7043
5
(Ductile Gr. 60-40-18)

3 Valve code
Automatically determines nominal
diameter and body material (see
page 03/09).

Code Lifting device

2 Gas-tight cap H2
Type 429

3 Plain lever H3
4 Packed lever H4
Plain lever with
5 H3
open bonnet

03/06 LWN 485.01-E

Type 427, 429

4 Options
5 Documentation
6
Code and Medium

J22 H01 L30 2.0

Type 427, 429 Option code Please select the necessary

1 2
documentation:
• O-ring disc
Tests, Option
2 . 0
CR “K” J21
EPDM “D” J22 Certifications: code
FKM “L” J23 DIN EN 10204-3.2: TÜV-Nord 1 Code
FFKM “C” J20 Certification for set pressure M33 2. CE / VdTUEV
• Disc 1.4404 / 316L L44 3. ASME Section VIII
• Disc 1.4404 / 316L stellited J25 LESER CGA (Certificate H03 + CE / VdTUEV
• Balanced bellows for Global Application)
- Bonnet, open (Type 427) J68 2 Medium
- Acceptance test certificate 3.1
- Bonnet, closed (Type 429) J78 .0 steam / gases / liquids
acc.to DIN EN 10204
• Elastomer bellows J79 (only valid for CE / VdTUEV)
- Declaration of conformity as per
• High temperature alloy spring X01
pressure equipment directive
• Stainless steel spring X04
PED 97/23/EC
• Adapter for lift indicator H4 J39
• Lift indicator J93
• Test gag Material quality certificate:
- Cap H2 J70 DIN EN 10204-3.1
- Packed lever H4 J69
• O-ring damper Component Option code
- Cap H2 J65 Body H01
- Packed lever H4 J66 Bonnet L30
• Heating jacket Cap / lever cover L31
- Couplings G 3/8 H29 Disc L23
G 3/4 H30 Screws N07
- Flange DN 15 H31 Nuts N08

Type 429
DN 25 H32
• Drain hole G 1/4 J18
G 1/2 J19
• Oil and grease free J85
• Materials
- NACE N78

Option code applies

only if not standard

LWN 485.01-E 03/07

 Type 427, 429
How to order – Article numbers

Type 429 Type 429

Cap H2 Plain lever H3
Closed bonnet Closed bonnet
Conventional design Conventional design

Type 429
Packed lever H4
Type 429

Closed bonnet
Conventional design

Type 427 Type 429

Plain lever H3 Cap H2
Open bonnet Closed bonnet
Conventional design Balanced bellows design

03/08 LWN 485.01-E

Type 427, 429
How to order – Article numbers

Article numbers
DNI 15 20 25 32 40 50 65 80 100 125 150
DNO 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Body material: 0.7043 (Ductile Gr. 60-40-18)
Bonnet H2 Art.-No. 4295. 8612 8622 8632 8642 8652 8662 8672 8682 8692 – –
closed H3 Art.-No. 4295. 8613 8623 8633 8643 8653 8663 8673 8683 8693 – –
H4 Art.-No. 4295. 8614 8624 8634 8644 8654 8664 8674 8684 8694 – –
open H3 Art.-No. 4275. 8615 8625 8635 8645 8655 8665 8675 8685 8695 – –
Body material: 1.0619 (WCB)
Bonnet H2 Art.-No. 4292. 7122 7132 7142 7152 7162 7172 7182 7192 7202 7212 7222
closed H3 Art.-No. 4292. 7123 7133 7143 7153 7163 7173 7183 7193 4203 7213 7223
H4 Art.-No. 4292. 7124 7134 7144 7154 7164 7174 7184 7194 4204 7214 7224
open H3 Art.-No. 4272. 7125 7135 7145 7155 7165 7175 7185 7195 4205 7215 7225
Body material: 1.4408 (CF8M)
Bonnet H2 Art.-No. 4294. 7242 7252 7262 7272 7282 7292 7302 7312 7322 – –
closed H4 Art.-No. 4294. 7244 7254 7264 7274 7284 7294 7304 7314 7324 – –

Type 429

LWN 485.01-E 03/09

 Type 427, 429
Pressure temperature ratings

Metric units
DNI 15 20 25 32 40 50 65 80 100 125 150
DNO 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Body material: 0.7043 (Ductile Gr. 60-40-18)
DIN flange Inlet PN 16 – –
Outlet PN 16 – –
Minimum set pressure
p [barg] S/G/L 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 – –

Min. set pressure1)

standard bellows p [barg] S/G/L 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 – –

Min. set pressure

low pressure bellows p [barg] S/G/L – 2.0 2.0 2.0 1.8 1.9 1.8 1.8 1.2 – –

Maximum set pressure

p [barg] S/G/L 40 40 40 40 40 40 35 35 30 – –

Max. set pressure

with special spring p [barg] S/G/L 40 40 40 40 40 40 40 35 30 – –

Temperature2) min. [°C] -60 – –

acc. to DIN EN max. [°C] +350 – –

1)
Min. set pressure of standard bellows = max. set pressure of bellows for low set pressure.
2)
The temperature is limited by the soft seal material (see page 99/10). The values given here are valid for EPDM.
Between -10°C and the lowest specified application temperature, proceed acc. to AD 2000-Merkblatt W10.

Metric units
DNI 15 20 25 32 40 50 65 80 100 125 150
DNO 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Type 429

Actual orifice area

113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Body material: 1.0619 (WCB)
DIN flange Inlet PN 40
Outlet PN 40
Minimum set pressure
p [barg] S/G/L 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5

Min. set pressure1)

standard bellows p [barg] S/G/L 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0

Min. set pressure on

low pressure bellows p [barg] S/G/L – 2.0 2.0 2.0 1.8 1.9 1.8 1.8 1.2 1.2
request
Maximum set pressure
p [barg] S/G/L 40 40 40 40 40 40 35 35 30 32 16

Max. set pressure

with special spring p [barg] S/G/L 40 40 40 40 40 40 40 35 30 32 16

Temperature2) min. [°C] -85

acc. to DIN EN max. [°C] +450

03/10 LWN 485.01-E

Type 427, 429
Pressure temperature ratings

Metric units
DNI 15 20 25 32 40 50 65 80 100 125 150
DNO 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
Body material: 1.4408 (CF8M)
DIN flange Inlet – –
Outlet – –
Minimum set pressure
p [barg] S/G/L 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 – –

Min. set pressure1)

standard bellows p [barg] S/G/L 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 – –

Min. set pressure

low pressure bellows p [barg] S/G/L – 2.0 2.0 2.0 1.8 1.9 1.8 1.8 1.2 – –

Maximum set pressure

p [barg] S/G/L 40 40 40 40 40 31.6 31.0 30 22 – –

Max. set pressure

with special spring p [barg] S/G/L 40 40 40 40 40 40 31 30 22 – –

Temperature2) min. [°C] -270 – –

acc. to DIN EN max. [°C] +400 – –

1)
Min. set pressure of standard bellows = max. set pressure of bellows for low set pressure.
2)
The temperature is limited by the soft seal material (see page 99/10). The values given here are valid for EPDM.
Between -10°C and the lowest specified application temperature, proceed acc. to AD 2000-Merkblatt W10.

Type 429

LWN 485.01-E 03/11

 Type 427, 429
Dimensions and weights

Metric units
DNI 15 20 25 32 40 50 65 80 100 125 150
DNO 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]

Weight 5 6 6 8 9 12 15 20 33 48 65
[kg] with bellows 6.3 6.4 6.4 8.4 9.6 13 16 21.6 35.6 52.1 78.4
Centre to face Inlet a 90 95 100 105 115 125 145 155 175 200 225
[mm] Outlet b 90 95 100 105 115 125 145 155 175 200 225
Height (H4) Standard H max. 310 307 311 320 320 360 476 525 609 743 865
[mm] Bellows H max. 359 337 341 355 355 425 536 595 684 823 960
Support brackets A 277
[mm] B 160
(Drilled only on request, C Ø 18
option code H42) D 278
E 21

Body material: 0.7043 (Ductile Gr. 60-40-18)

DIN flange1) Inlet PN 40 – –
Outlet PN 40 – –
Body material: 1.0619 (WCB)
DIN flange1) Inlet PN 40
Outlet PN 40
Body material: 1.4408 (CF8M)
DIN flange1) Inlet PN 40 – –
Outlet PN 40 – –
1)
Standard flange class For other flange drillings, see page 03/13.
Type 429

Conventional design Support brackets Balanced bellows design

03/12 LWN 485.01-E

Type 427, 429
Flange drillings

Flange drillings
DNI
15 20 25 32 40 50 65 80 100 125 150
DNO
15 20 25 32 40 50 65 80 100 125 150
Valve size 1/2" x 1/2" 3/4" x 3/4" 1" x 1" 1 1/4" x1 1/4" 1 1/2" x1 1/2" 2" x 2" 21/2" x 21/2" 3" x 3" 4" x 4" 5" x 5" 6" x 6"
Actual orifice diameter d0 [mm] 12 18 18 18 23 29 37 46 60 74 92
Actual orifice area A0 [mm2] 113 254 254 254 416 661 1075 1662 2827 4301 6648
Body material: 0.7043 (Ductile Gr. 60-40-18), 1.0619 (WCB), 1.4408 (CF8M)
PN 10 * * * * * * H44 H44 H44 H44 H44
PN 16 * * * * * * H45 H45 H45 H45 H45
DIN EN 1092
PN 25 * * * * * * * * * * *
Inlet
PN 40 * * * * * * * * * * *
CL150 H64 H64 H64 H64 H64 H64 H64 H64 [H64] H64 H64
ASME B16.51)
CL300 [H65] – H65 H65 – [H65] [H65] – – – –
PN 10 * * * * * * H50 H50 H50 H50 H50
PN 16 * * * * * * H51 H51 H51 H51 H51
DIN EN 1092
PN 25 * * * * * * * * * * *
Outlet
PN 40 * * * * * * * * * * *
CL150 H79 H79 H79 H79 H79 H79 H79 H79 [H79] H79 H79
ASME B16.51)
CL300 H80 – H80 H80 – [H80] [H80] – – – –

Flange facings
Information Standard Inlet Outlet Remark
General
Flange, undrilled – H38 H39
Linde-V-Nut, Form V48 Linde Standard 420-08 J07 J08 Groove: Rz = 16
Linde-V-Nut, Form V48A LWN 313.36 J05 J06 Groove: Rz = 4, e.g. for hydrogen
Lens-shape seal form L DIN 2696
J11 J12
(without lens-shape seal) LWN 313.35
According to DIN EN 1092
Flange facings Remark
Inlet Outlet
DIN EN 1092 Rz specification
(also see LWN 313.40) PN 10 – PN 40 PN 10 – PN 40 acc. to DIN EN 1092 in µm

Form B1 Seal. strip.: Rz = 12.5 – 50

* *

Type 429
Sealing strip
Form B2 L36 L38 Seal. strip.: Rz = 3.2 – 12.5
only for steel flange

Tongue, Form C1) H94 H92

Groove, Form D1) H93 H91
Male, Form E H96 H98
Female, Form F H97 H99
O-ring Male, Form G J01 J02
O-ring Female, Form H J03 J04
According to ASME B16.5
Smooth Finish2) Serrated Finish RTJ-Groove

Body material Inlet Outlet Inlet Outlet Inlet Outlet Inlet Outlet
Pressure Pressure
Option code Option code Option code Option code
level level

0.7043, 1.0619, 1.4408 all all L52 L53 – – – –

* *
1)
LESER manufactures the groove at flanged valves by milling. If a customer demands a turned surface in the soil of the groove according to DIN EN 1092-1
an additional option code is necessary: “S01: soil of the groove drilled”.
2)
Smooth finish is not defined in the effective standards.

For an explanation of signs and symbols, refere to page 00/07.

Note: Flange drillings and facings always meet the requirements of mentioned flange standards.
Flange thickness and outer diameter may deviate from flange standard.

LWN 485.01-E 03/13

 Type 427, 429
Order information – Spare parts

Spare parts
DNI 15 20 25 32 40 50
DNO 15 20 25 32 40 50
Actual orifice diameter
12 18 18 18 23 29
d0 [mm]
Actual orifice area
113 254 254 254 416 661
A0 [mm2]
Disc (item 7): Metal seat Material-No. / Art.-No.
Disc 1.4122 212.3439.9000 211.0139.9000 211.0139.9000 211.0139.9000 211.0239.9000 211.0339.9000
Detachable lifting aid 1.4404 212.3449.9000 211.0149.9000 211.0149.9000 211.0149.9000 211.0249.9000 211.0349.9000
Disc (item 7): Soft seal Material-No. / Art.-No.
Disc CR “K” – 200.6849.9051 200.6849.9051 200.6849.9051 200.6849.9051 200.7049.9051
EPDM “D” – 200.6849.9041 200.6849.9051 200.6849.9041 200.6849.9051 200.7049.9041
FKM “L” – 200.6849.9071 200.6849.9051 200.6849.9071 200.6849.9051 200.7049.9071
FFKM “C” – 200.6849.9091 200.6849.9051 200.6849.9091 200.6849.9051 200.7049.9091
O-ring (item 7.4): Soft seal Material-No. / Art.-No.
O-ring CR “K” – 502.0171.2651 502.0171.2651 502.0171.2651 502.0249.3551 502.0313.3551
EPDM “D” – 502.0171.2641 502.0171.2641 502.0171.2641 502.0249.3541 502.0313.3541
FKM “L” – 502.0171.2671 502.0171.2671 502.0171.2671 502.0249.3571 502.0313.3571
FFKM “C” – 502.0171.2691 502.0171.2691 502.0171.2691 502.0249.3591 502.0313.3591
Bellows (item 15): 1.4571 Material-No. / Art.-No.
Standard bellows 400.0149.0000 400.0149.0000 400.0149.0000 400.0149.0000 400.0249.0000 400.0349.0000
Conversion kit, standard1) 5021.1030 5021.1034 5021.1034 5021.1034 5021.1035 5021.1036
Low pressure bellows – 400.0149.0021 400.0149.0021 400.0149.0021 400.0249.0021 400.0349.0021
Conversion kit low pressure1) Please specify application conditions
Gasket – body / bonnet (item 60) Material-No. / Art.-No.
Gasket Graphite + 1.4401 500.0407.0000 500.0407.0000 500.0407.0000 500.0407.0000 500.0407.0000 500.0507.0000
Option code L68 Gylon (PTFE compliance) 500.0405.0000 500.0405.0000 500.0405.0000 500.0405.0000 500.0405.0000 500.0505.0000
Ball (item 61): Material-No. / Art.-No.
Ball Ball Ø [mm] 6 6 6 6 6 6
1.4404 510.0104.0000 510.0104.0000 510.0104.0000 510.0104.0000 510.0104.0000 510.0104.0000
Split ring (item 14): Material-No. / Art.-No.
Split ring Spindle Ø [mm] 12 12 12 12 12 12
1.4404 251.0149.0000 251.0149.0000 251.0149.0000 251.0149.0000 251.0149.0000 251.0149.0000
Pin (item 57) Material-No. / Art.-No.
Type 429

Pin 1.4310 480.0505.0000 480.0505.0000 480.0505.0000 480.0505.0000 480.0505.0000 480.0705.0000

O-ring damper Material-No. / Art.-No.
Conversion kit H2 5021.1060 – 5021.1060 5021.1060 5021.1060 5021.1060
Conversion kit H4 5021.1064 – 5021.1064 5021.1064 5021.1064 5021.1064
1)
Pressure range, see page 03/10 – 03/11

A conversion kit includes the following components:

Item. Components No.

8 Guide with bushing 1

11 Bonnet spacer 1
12 Spindle 1
15 Bellows 1
55 Stud 4, 8 dependant on valve size
60 Gasket 2, 3 dependant on valve size
Installation instruction LWN 037.05 1

Refer to page 03/04

03/14 LWN 485.01-E

Type 427, 429
Order information – Spare parts

Spare parts
DNI 65 80 100 125 150
DNO 65 80 100 125 150
Actual orifice diameter
37 46 60 74 92
d0 [mm]
Actual orifice area
1075 1662 2827 4301 6648
A0 [mm2]
Disc (item 7): Metal seat Material-No. / Art.-No.
Disc 1.4122 211.0439.9000 211.0639.9000 212.0539.9000 212.0639.9000 211.1239.9000
Detachable lifting aid 1.4404 211.0449.9000 211.0649.9000 212.0549.9000 212.0649.9000 212.0749.9000
Disc (item 7): Soft seal Material-No. / Art.-No.
Disc CR “K” 200.7149.9051 200.7249.9051 200.7349.9051 200.7449.9051 on request
EPDM “D” 200.7149.9041 200.7249.9041 200.7349.9041 200.7449.9041 on request
FKM “L” 200.7149.9071 200.7249.9071 200.7349.9071 200.7449.9071 200.7549.9071
FFKM “C” 200.7149.9091 200.7249.9091 on request on request on request
O-ring (item 7.4): Soft seal Material-No. / Art.-No.
O-ring CR “K” 502.0408.3551 502.0503.3551 502.0660.5351 502.0819.5351 on request
EPDM “D” 502.0408.3541 502.0503.3541 502.0660.5341 502.0819.5341 on request
FKM “L” 502.0408.3571 502.0503.3571 502.0660.5371 502.0819.5371 502.1041.5371
FFKM “C” 502.0408.3591 502.0503.3591 on request on request on request
Bellows (item 15): 1.4571 Material-No. / Art.-No.
Standard bellows 400.0449.0000 400.0549.0000 400.0649.0000 400.0749.0000 400.0849.0000
Conversion kit, standard1) 5021.1037 5021.1038 5021.1039 Component parts Component parts
Low pressure bellows 400.0449.0021 400.0549.0021 400.0649.0021 400.1107 400.0849.0021
1)
Conversion kit low pressure Please specify application conditions – –
Gasket – body / bonnet (item 60) Material-No. / Art.-No.
Gasket Graphite + 1.4401 500.0907.0000 500.1007.0000 500.1507.0000 500.1807.0000 500.2107.0000
Option code L68 Gylon (PTFE compliance) 500.0905.0000 500.1005.0000 500.1505.0000 500.1805.0000 500.2105.0000
Ball (Item 61): Material-No. / Art.-No.
Ball Ball Ø [mm] 9 9 12 12 15
1.4404 510.0204.0000 510.0204.0000 510.0304.0000 510.0304.0000 510.0404.0000
Split ring (item 14): Material-No. / Art.-No.
Split ring Spindle Ø [mm] 16 16 16 20 24
1.4404 251.0249.0000 251.0249.0000 251.0249.0000 251.0349.0000 251.0449.0000
Pin (item 57) Material-No. / Art.-No.

Type 429
Pin 1.4310 480.0705.0000 480.0705.0000 480.1005.0000 480.1005.0000 480.1105.0000
O-ring damper Material-No. / Art.-No.
Conversion kit H2 5021.1061 5021.1061 – – –
Conversion kit H4 5021.1065 5021.1065 – – –
1)
Pressure range, see page 03/10 – 03/11
One bellows conversion set includes the following components:

Item. Components No.

8 Guide with bushing 1

11 Bonnet spacer 1
12 Spindle 1
15 Bellows 1
55 Stud 4, 8 dependant on valve size
60 Gasket 2, 3 dependant on valve size
Installation instruction LWN 037.05 1

Refer to page 03/04

LWN 485.01-E 03/15

 Type 427, 429
Available options For more information, also see
“Accessories and options” as of page 99/01.

Heating jacket Drain hole Open bonnet

H29, H30: Coupling G 3/8, G 3/4 J18: G 1/4 See Art.-No.
H31, H32: Flange DN15, DN25 J19: G 1/2

O-ring disc Balanced bellows Conversion set for

J20: FFKM “C” J68: Open bonnet balanced bellows
J21: CR “K” J78: Closed bonnet Art.-No. see page 02/14
J22: EPDM “D”
J23: FKM “L”

Screwed cap H2 Plain lever H3 Packed lever H4

H2 H3 H4
Type 429

O-ring damper H2 O-ring damper H4 Lift indicator Test gag

J65 J66 J39: Adaptor H4 J69: H4
J93: Lift indicator J70: H4

03/16 LWN 485.01-E

Type 427, 429
Approvals

Approvals
DNE 15 – 150
DNA 15 – 150
Actual orifice diameter
12 – 92
d0 [mm]
Actual orifice area
113 – 6648
A0 [mm2]
Europa Coefficient of discharge Kdr
PED / DIN EN ISO 4126-1 Approval-No. 072020111Z0008/0/04
S/G 0.13
L The valve is component tested for liquids with thermal expansion.
Germany Coefficient of discharge α w
PED / AD 2000-Merkblatt A2 Approval-No. TÜV SV 610
Proportional safety valve S/G 0.13
L The valve is component tested for liquids with thermal expansion.
China Coefficient of discharge α w
AQSIQ Approval-No. For current Approval-No. see www.leser.com
S/G 0.13
L The valve is component tested for liquids with thermal expansion.
Belarus Coefficient of discharge α w
GOSPROMNAZADOR Approval-No. For current Approval-No. see www.leser.com
S/G 0.13
L The valve is component tested for liquids with thermal expansion.
Classification societies
on request
Information:
According to AD 2000-Merkblatt A2 Chap. 10.3, the discharge coefficient “... for normal or proportional safety valves, should not exceed the
value αw= 0.08 for S/G or the value αw = 0.05 for L.” Since the actual αw value for liquids is below the requirements of the AD 2000-Merkblatt
for the Series 429, it is not possible to accord a discharge coefficient αw.

Type 429

LWN 485.01-E 03/17

 Type 427, 429
Capacities – Steam

Calculation of the capacity for saturated steam acc. to AD 2000-Merkblatt A2 with 10% overpressure.
Capacities at 1 bar and lower are calculated at 0.1 bar overpressure.

Metric units AD 2000-Merkblatt A2 [kg/h]

DNI 15 20 25 32 40 50 65 80 100 125 150
DNO 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
) 2
LEOS/G* [inch ] 0.023 0.053 0.053 0.053 0.086 0.137 0.222 0.343 0.584 0.889 1.374
Set pressure [bar] Capacity [kg/h]
1.5 22 50 50 50 81 130 211 326 555 843 1304
2 27 60 60 60 98 155 253 391 665 1012 1564
3 35 79 79 79 130 206 336 519 883 1343 2076
4 44 99 99 99 162 257 419 647 1101 1675 2589
5 53 119 119 119 194 308 501 775 1318 2005 3099
6 61 138 138 138 225 358 584 902 1534 2334 3608
7 70 157 157 157 256 408 664 1026 1746 2655 4104
8 78 176 176 176 288 458 746 1152 1960 2982 4609
9 87 196 196 196 320 508 827 1278 2175 3308 5114
10 96 215 215 215 351 558 909 1404 2389 3635 5618
12 113 254 254 254 414 658 1072 1656 2818 4286 6625
14 130 291 291 291 476 756 1231 1903 3238 4925 7612
16 147 330 330 330 539 856 1394 2154 3665 5575 8617
18 164 368 368 368 601 956 1557 2406 4093 6226
20 181 407 407 407 665 1056 1720 2658 4522 6879
22 198 444 444 444 726 1154 1878 2903 4938 7511
24 215 483 483 483 789 1254 2041 3155 5368 8165
26 232 522 522 522 852 1355 2205 3408 5798 8820
28 249 561 561 561 915 1455 2369 3662 6230 9477
30 267 600 600 600 979 1557 2534 3917 6663 10136
32 284 639 639 639 1043 1658 2699 4172 10797
34
36
Type 429

38
40
)
* LEO S/G = LESER Effective Orifice steam/gases please refer to page 00/11
“How to use” capacity tables, refer to page 00/09

03/18 LWN 485.01-E

Type 427, 429
Capacities – Air

Calculation of the capacity for air acc. to AD 2000-Merkblatt A2 with 10% overpressure at 0 °C and 1013 mbar.
Capacities at 1 bar and below are calculated with 0.1 bar overpressure.

Metric units AD 2000-Merkblatt A2 [mn3/h]

DNI 15 20 25 32 40 50 65 80 100 125 150
DNO 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
) 2
LEOS/G* [inch ] 0.023 0.053 0.053 0.053 0.086 0.137 0.222 0.343 0.584 0.889 1.374
Set pressure [bar] Capacity [mn3/h]
1.5 27 60 60 60 98 156 253 391 666 1013 1565
2 32 72 72 72 118 188 306 472 803 1222 1889
3 43 97 97 97 159 252 410 634 1079 1641 2536
4 54 122 122 122 199 316 515 796 1354 2060 3184
5 65 147 147 147 239 381 620 958 1629 2479 3831
6 76 171 171 171 280 445 724 1120 1905 2897 4478
7 87 196 196 196 320 509 829 1281 2180 3316 5126
8 98 221 221 221 361 574 934 1443 2455 3735 5773
9 109 246 246 246 401 638 1038 1605 2731 4154 6420
10 120 271 271 271 442 702 1143 1767 3006 4573 7068
12 142 320 320 320 523 831 1353 2091 3557 5410 8362
14 164 370 370 370 604 960 1562 2414 4107 6248 9657
16 186 419 419 419 684 1088 1771 2738 4658 7086 10952
18 208 469 469 469 765 1217 1981 3062 5209 7923
20 230 518 518 518 846 1345 2190 3385 5759 8761
22 252 568 568 568 927 1474 2400 3709 6310 9598
24 274 617 617 617 1008 1603 2609 4033 6861 10436
26 296 667 667 667 1089 1731 2818 4356 7411 11274
28 318 717 717 717 1170 1860 3028 4680 7962 12111
30 341 766 766 766 1251 1989 3237 5004 8513 12949
32 363 816 816 816 1332 2117 3447 5327 13786
34 385 865 865 865 1413 2246 3656 5651
36 407 915 915 915 1494 2375 3865

Type 429
38 429 964 964 964 1575 2503 4075
40 451 1014 1014 1014 1655 2632 4284

*) LEO S/G = LESER Effective Orifice steam/gases please refer to page 00/11
“How to use” capacity tables, refer to page 00/09

LWN 485.01-E 03/19

 Type 427, 429
Capacities – water

Acc. to AD 2000-Merkblatt A2, the LESER safety valve type 427, 429 can be used for thermal expansion in spite of having no component testing
for liquids. To calculate the water capacity table, a coefficient of discharge of αw = 0.05 was used.

Calculation of the capacity for water as per AD 2000-Merkblatt A2 with 10% overpressure at 20 °C.
Capacities at 1 bar and below are calculated with 0.1 bar overpressure.

Metric units AD 2000-Merkblatt A2 [103kg/h]

DN 15 20 25 32 40 50 65 80 100 125 150
DNO 15 20 25 32 40 50 65 80 100 125 150
Actual orifice diameter
12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Actual orifice area
113 254 254 254 416 661 1075 1662 2827 4301 6648
A0 [mm2]
) 2
LEOL* [inch ] 0.009 0.020 0.020 0.020 0.033 0.053 0.085 0.132 0.225 0.342 0.528
Set pressure [bar] Capacity [103kg/h]
1.5 0.30 0.67 0.67 0.67 1.09 1.73 2.81 4.34 7.39 11.2 17.4
2 0.34 0.77 0.77 0.77 1.25 1.99 3.24 5.02 8.53 13.0 20.1
3 0.42 0.94 0.94 0.94 1.54 2.44 3.97 6.14 10.4 15.9 24.6
4 0.48 1.09 1.09 1.09 1.77 2.82 4.59 7.09 12.1 18.4 28.4
5 0.54 1.21 1.21 1.21 1.98 3.15 5.13 7.93 13.5 20.5 31.7
6 0.59 1.33 1.33 1.33 2.17 3.45 5.62 8.69 14.8 22.5 34.7
7 0.64 1.44 1.44 1.44 2.35 3.73 6.07 9.38 16.0 24.3 37.5
8 0.68 1.54 1.54 1.54 2.51 3.99 6.49 10.0 17.1 26.0 40.1
9 0.72 1.63 1.63 1.63 2.66 4.23 6.88 10.6 18.1 27.5 42.6
10 0.76 1.72 1.72 1.72 2.80 4.46 7.26 11.2 19.1 29.0 44.9
12 0.84 1.88 1.88 1.88 3.07 4.88 7.95 12.3 20.9 31.8 49.1
14 0.90 2.03 2.03 2.03 3.32 5.27 8.58 13.3 22.6 34.3 53.1
16 0.97 2.17 2.17 2.17 3.55 5.64 9.18 14.2 24.1 36.7 56.7
18 1.02 2.30 2.30 2.30 3.76 5.98 9.73 15.0 25.6 38.9
20 1.08 2.43 2.43 2.43 3.96 6.30 10.3 15.9 27.0 41.0
22 1.13 2.55 2.55 2.55 4.16 6.61 10.8 16.6 28.3 43.0
24 1.18 2.66 2.66 2.66 4.34 6.90 11.2 17.4 29.6 45.0
26 1.23 2.77 2.77 2.77 4.52 7.19 11.7 18.1 30.8 46.8
28 1.28 2.87 2.87 2.87 4.69 7.46 12.1 18.8 31.9 48.6
30 1.32 2.97 2.97 2.97 4.86 7.72 12.6 19.4 33.0 50.3
32 1.37 3.07 3.07 3.07 5.02 7.97 13.0 20.1 51.9
34 1.41 3.17 3.17 3.17 5.17 8.22 13.4 20.7
36 1.45 3.26 3.26 3.26 5.32 8.46 13.8
Type 429

38 1.49 3.35 3.35 3.35 5.47 8.69 14.1

40 1.53 3.43 3.43 3.43 5.61 8.91 14.5
)
* LEOL = LESER Effective Orifice liquids please refer to page 00/11
“How to use” capacity tables, refer to page 00/09

03/20 LWN 485.01-E

 Accessories
and Options
Contents Chapter/Page

Overview 99/02
Caps and levers 99/04
Metal seat 99/06
Disc with soft seal 99/08
Soft seal disc 99/10
Disc 99/11
Balanced bellows 99/12
Heating jacket 99/14
O-ring damper 99/16
Elastomer bellows 99/18
Lift indicator 99/19
Lift stoppers 99/20

Options

LWN 485.01-E 99/01

 Accessories and Options
Overview

Options
Type Option code 431, 433 431, 433 PN 160 427, 429
Disc (item 7):
Disc with detachable lifting aid J26 ✓ * *
Bull race disc J24 ✓ ✓ ✓
Seal type (item 5 and 7)
Disc 1.4404 L44 ✓ ✓ ✓
Metal seat
Disc 1.4404 stellited J25 ✓ ✓ ✓
CR “K” J21 ✓ ✓ ✓
NBR “N” J30 ✓ ✓ ✓
O-Ring

EPDM “D” J22 ✓ ✓ ✓

FKM “L” J23 ✓ ✓ ✓
Soft seal
FFKM “C” J20 ✓ ✓ ✓
SP “T” J49 ✓ on request –
Sealing
plate

PCTFE “G” J48 ✓ on request –

PTFE “A” J44 ✓ on request –
Bellows (item 15, item 70)
Standard bellows J68 ✓ ✓ ✓
Open
bonnet
Low pressure bellows J68J63 ✓ – ✓

Standard bellows J78 ✓ ✓ ✓

Bonnet
Low pressure bellows J78J63 ✓ – ✓
closed
Other materials J25 + Material name ✓ ✓ ✓

EPDM J79 ✓ – ✓
Elastomer
bellows
NBR J87 ✓ – ✓
Caps and levers (item 40)
H2 ✓ ✓ ✓
H3 ✓ ✓ ✓
H4 ✓ ✓ ✓
Spring (item 54)
High temperatue alloy 1.8159 / 1.7102 X01 ✓ ✓ ✓
Stainless steel 1.4310 X04 ✓ ✓ ✓
Options

99/02 LWN 485.01-E

Accessories and Options
Overview

Options
Type Option code 431, 433 431, 433 PN 160 427, 429
Test gag
H2 J70 ✓ ✓ ✓
H4 J69 ✓ ✓ ✓
Bonnet (item 9)
closed ✓ ✓ ✓
open ✓ ✓ ✓
Heating jacket
✓ ✓ ✓
Lift indicator
Lifting device H2, H4 J39J93 ✓ ✓ ✓
Lift stoppers
Bush J51 ✓ ✓ ✓
Gag H2 J52 ✓ ✓ ✓
Gag H4 J50 ✓ ✓ ✓
Drain hole
G 1/4 J18 ✓ ✓ ✓
1
G /2 J19 ✓ ✓ ✓
O-ring damper (item 40)
H2 H65 ✓ ✓ ✓
H4 H66 ✓ ✓ ✓
Bursting disc
H2 ✓ ✓ ✓

Options

LWN 482.01-D 99/03

 Accessories and Options
Caps and levers – subassembly item 40

Cap H2 Packed lever H4

1

12

2 14 1.5

25 13

25 3a
24

24
1.6
23
23

1.8
1.10
1.7
1.11

1.9

1.4

Plain lever H3 Test gag

Cap H2: J70
Packed lever H4: J69
12

14 93.5
93
6
13
3b
1
22 BLOCKED
23 Remove screw
after testing

24

10

Test gag The test gag is used to:

– perform the pressure test in a system without
The test gag prevents the spindle from lifting and keeps the disassembling the safety valve
safety valve tight while the system pressure exceeds the set – be able to make an adjustment to each individual valve
pressure. in systems with multiple safety valves
Options

The test gag must be removed after testing, otherwise

the safety valve will not protect the system against
impermissible overpressure.

99/04 LWN 485.01-E

Accessories and Options
Caps and levers – subassembly item 40

Materials
Steel Stainless steel

Item. Component Cap H2 Plain lever H3 Packed lever H4 Cap H2 Packed lever H4

– 0.7040 0.7040 – 1.4408

1 Lever cover
– Gr. 60-40-18 Gr. 60-40-18 – CF8M
1.0718 – – 1.4404 –
2 Cap
Steel – – 316L –
– – 1.4571 – 1.4571
3a Spacer
– – 316Ti – 316Ti
– 1.4401 – – –
3b Hex screw
– B8M – – –
– 1.4021 1.0718 – 1.4404
4 / 1.4 Shaft / bolt
– 420 Steel – 316L
– – 1.0531 – 1.4571
1.5 Lifting fork
– – Steel – 316Ti
– 0.7040 1.0036 – 1.4301
6 / 1.6 Lever
– Gr. 60-40-18 Steel – 304
– – 1.4401 – 1.4301
1.7 Washer
– – 316 – 304
– – A2/Poly – 1.4401
1.8 Nut
– – 2H – 8M
– – FKM – –
1.9 O-Ring
– – FKM – –
– – – – Graphite
1.9 Packing ring precast
– – – – Graphite
– Carbon steel Carbon steel – –
10 / 1.10 Retaining clip
– Carbon steel Carbon steel – –
– – – – 1.4104
1.10 Nut
– – – – Chrome steel
– – – – 1.4404
1.10 Packing gland
– – – – 316L
– – Carbon steel – –
1.11 Support ring
– – Carbon steel – –
– 1.0718 1.0718 – 1.4404
12 Spindle cap
– Carbon steel Carbon steel – 316L
– Steel Steel – 1.4401
13 Pin
– Steel Steel – 8M
– 1.4571 1.4571 – 1.4571
14 Securing ring
– 316Ti 316Ti – 316Ti
– Plastic – – –
22 Plug
– Plastic – – –
Plastic Plastic Plastic Plastic Plastic
23 Seal
Plastic Plastic Plastic Plastic Plastic
1.4541 1.4541 1.4541 1.4541 1.4541
24 Seal wire
321 321 321 321 321
1.4435 – – 1.4435 1.4435
25 Sealing nose
316L – – 316L 316L
1.4401 – 1.4401 1.4401 1.4401
93 Test gag
B8M – B8M B8M B8M
Fiber – Fiber Fiber Fiber
93.5 Washer
Options

Fiber – Fiber Fiber Fiber

Note:

– LESER reserves the right to make changes

– LESER may use higher quality materials without giving prior information
– Each component can be constructed of another material according to the customer's specification.

LWN 485.01-E 99/05

 Accessories and Options
Metal seat – seat / nozzle, item 5 and disc subassembly item 7

With LESER, the metal seat surfaces (disc and seat) are Improved tightness (Option code J86) is available on request.
optically lapped planar to guarantee high seal tightness.
LESER safety valves are delivered with a standard seal tight-
ness acc. to API 527.

Series 431 / 433 Series 431 / 433 PN 160 Series 427 / 429

1 1 1

3
2

Stellited sealing surface

The sealing surfaces of stainless steel discs and seats / – for high-pressure applications
nozzles can be stellited by weld cladding. Stellite is a cobalt- with highly stressed sealing surfaces
chrome non-ferrous alloy with increased hardness, corrosion
– for high-temperature applications in order to prevent
resistance, and abrasion resistance even at high temperatures.
permanent deformation of the sealing surface as a
consequence of the material properties of the seat and disc
LESER recommends stellited sealing surfaces for Modulate
Action safety valves (seat / nozzle and disc (1.4404 / 316L)) - use with abrasive media in order to increase the abrasion
in the following applications: resistance of the sealing surface

Series 441
431 / 433 Series 431 / 433 PN 160

7.1

7.1

5
5

Materials for disc and seat / nozzle, see page 99/09.

Hardness Metal seat

Material Hardness of the sealing surface

Value according to standard or Mean value LESER

EN ASME
manufacturer specification bearing material

EN 10088-3, 1.4122 hardened Chrome steel, hardened ≥ 40 HRC LWN 325.01 hardening process 42 – 46 HRC
EN 10272, 1.4404 SA 479 316L ≤ 215 HBW EN 10272 Table 7 16 – 19 HRC1)
EN 10272, 1.4404 stellited SA 479 316L stellited ≥ 35 HRC Manufacturer specification 40 HRC

HBW: BRINELL hardness acc. to DIN EN ISO 6506-1 / HRC: ROCKWELL hardness acc. to DIN EN ISO 6508-1
Options

1)
Rockwell hardnesses less than 20 HRC are not approved by the standard. LESER gives these values for better comparability.

99/06 LWN 485.01-E

Accessories and Options
Metal seat – seat / nozzle, item 5 and disc subassembly item 7

Standard and corrosiv service

Materials Disc – subassembly item 7

Item Component Steel Stainless steel
Type 431 / 433
1.4122 hardened 1.4404
1 Disc
Hardened stainless steel 316L
1.4404 1.4404
2 Lifting aid
316L 316L
Type 431 / 433 PN 160
1.4122 hardened 1.4404
1 Disc
Hardened stainless steel 316L
1.4104 1.4404
2 Lifting aid
Chrome steel 316L
1.4571 1.4571
3 Circlip
316Ti 316Ti
Series 427 / 429
1.4122 hardened 1.4404
1 Disc
Hardened stainless steel 316L

Materials Seat / nozzle item 5

Item Component Steel Stainless steel
All series

5 Seat / nozzle 1.4404

Stellited sealing surface

Materials Seat / nozzle item 5, disc item 7

Item Component Option code
Type 431 / 433, 431 / 433 PN 160
1.4404 stellited
7.1 Disc J25
316L stellited
1.4404 stellited
5 Seat / nozzle L61 / L62
316L stellited Options

LWN 485.01-E 99/07

 Accessories and Options
Disc with soft seal – subassembly item 7

LESER soft seals provide increased seal tightness for your application.

Construction features
• Different constructions for an expanded • An easier and faster replacement of the soft seal reduces
range of applications service costs.
• Large selection of soft seal materials for almost • Standard ARP O-ring dimensions facilitate easy
any application, and custom made for the respective worldwide procurement.
customer requirement • A standard hardness for each O-ring material for all
• The increased service life of the seal compared to set pressures simplifies the stocking of spare parts
metal seats reduces the service costs. and reduces warehousing costs.

Design of soft seal O-ring disc

Type 431 / 433 433 PN 160 427 / 429
Nominal size DN 15 DN 20 – DN 150 DN 15 DN 20 – DN 150
Pressure range 0.3 – 40 bar 0.2 – 20 bar 0.2 – 160 bar 1.5 – 40 bar
Option code

7.5 7.5

CR “K” J21 7.3 7.3

7.1
EPDM “D” J22
7.1 7.1
FKM “L” J23 7.2
7.4 7.4
FFKM “C” J20 7.5

For temperature application limits, media resistance, and option codes, see selection table on page 99/10.
Materials for soft sealing disc, see page 99/09

Materials Disc – subassembly item 7

Type 431 / 433 433 PN 160 427 / 429
DN 15 DN 20 – DN 150 DN 15 DN 20 – DN 150
0.3 – 40 bar 0.2 – 40 bar 0.2 – 160 bar 1.5 – 40 bar

Item 1.4404 Item 1.4404 Item 1.4404

Disc
7.1 316L 7.1 316L 7.1 316L
Item 1.4404 – Item 1.4404
Retainer
7.3 316L – 7.3 316L
Soft seal Item O-ring Item O-ring Item O-ring
Materials, see page 99/10 7.4 7.5 7.4
see Item 7.1 Item 1.4404 –
Lifting aid
– 7.2 316L –
Item 1.4401 – Item 1.4401
Nut
7.5 8M – 7.5 8M
Options

For temperature application limits, media resistance and option codes, see selection table on page 04/08.

99/08 LWN 485.01-E

Accessories and Options
Soft seal disc – subassembly item 7

Construction Disc with sealing plate

Type 431 / 433 433 PN 160 427 / 429
Option code Pressure range
SP: “T” J49 10 – 40 bar – –
PCTFE: “G” J48 1.0 – 30 bar – –
PTFE: “A” J44 1.0 – 10 bar – –

Design

7.5

7.3

7.1
On request Not available
7.4

Materials Disc – subassembly item 7

Type 431 / 433 433 PN 160 427 / 429
DN 15 DN 20 – DN 150 DN 15 DN 20 – DN 150
0.3 – 40 bar 0.2 – 40 bar 0.2 – 160 bar 1.5 – 40 bar

Item 1.4404 – –
Disc
7.1 316L – –
Item 1.4404 – –
Retainer
7.3 316L – –
Soft seal Item Sealing plate – –
Materials, see page 99/10 7.4 – –
see Item 7.1 – –
Lifting aid
– – –
Item 1.4401 – –
Nut
7.5 8M – –

For temperature application limits, media resistance and option codes, see selection table on page 04/08.
Options

LWN 485.01-E 99/09

 Accessories and Options
Soft seal

Soft seal selection

Abbrevation Trade name Code Option Tmin Tmax
Application2)
ASTM 14 (Designation) letter1) code [°C] [°C]
O-Ring

Paraffins, mineral oils, silicon oils and greases,

CR Neoprene® K J21 -40 100
water and aqueous solutions, refrigerants, ozone

Buna-N®
NBR N J30 -25 100 Hydraulic oils, plant and animal fats and oils
(Nitrile-Butadiene)

Buna-EP Hot water and hot steam up to 150 °C, 302 °F,
EPDM (Ethylene-Propylene- D J22 -45 150 many organic and inorganic acids, silicon oils and
Dine) greases FDA conforming compound

High temperatures (not hot steam), mineral oils and

Viton®
FKM (Fluorocarbon) L J23 20 180 greases, silicon oils and greases, plant and animal oils
and fats, ozone FDA conforming compound on request

Almost all chemicals, standard compound is Kalrez®

Kalrez®
FFKM (Perfluor) C J20 0 250 6375 with steam resistance FDA conforming compound
on request

Sealing plate

High-temperature and high-pressure applications

VESPEL SP-1® 3)
SP (Polyimide) T J49 -270 300 (no steam), chemical resistance, see manufacturer's
specifications

KEL-F® Low-temperature and refrigeration system applications,

PCTFE (Polychlorotri- G J48 -270 204 flammable media, gaseous acid up to 50 bar, 725 psig
fluoroethylene) at 60 °C, 140 °F

Teflon®
PTFE (Polytetrafluoro- A J44 -184 150 Almost all chemicals
ethylene)

Other not listed materials X For other materials, please contact your local representative or [email protected].

1)
The code letters are stamped on the disc (Item 1)
2)
The pressure and temperature application range must be observed in all cases. The chemical resistance is based on specifications from the soft
seal manufacturer. LESER assumes no guarantee.
3)
Only for DN 25, 1" x 2".
Options

99/10 LWN 485.01-E

Accessories and Options
Disc – subassembly item 7

Disc with detachable lifting aid

A detachable lifting aid can be supplied for the valve disc This makes it possible to have fast maintenance of the safety
on request as a variation of the standard disc with an inte- valve on site.
grally fixed lifting aid. The benefit of the detachable lifting aid The detachable lifting aid is standard with safety valves of type
is the easy re-lapping of the disc sealing surface on one disc. 431 / 433 PN 160.

Construction
Type 431, 433 431, 433 PN 160 427, 429

1 1
Construction
3
3
Safety valves
2
without lifting aid
2

Option code J26 –

*
Materials Disc with detachable lifting aid
Item Name Steel Stainless steel
Series 431 / 433
1.4122 hardened 1.4404
1 Disc
Hardened stainless steel 316L
1.4581 1.4581
2 Lifting aid
CF10M CF10M
1.4310 1.4310
3 Roll pin
Stainless steel Stainless steel
Series 431 / 433 PN 160
1.4122 hardened 1.4404
1 Disc
Hardened stainless steel 316L
1.4104 1.4404
2 Lifting aid
Chrome steel 316L
1.4571 1.4571
3 Circlip
316Ti 316Ti

Bull race disc

To prevent damages to the sealing surfaces from frequent disassembly, in particular for safety valves with short or regular
service intervals, the disc can be supplied in a bull race construction as a custom design.

Construction
Type 431, 433 431, 433 PN 160 427, 429

1
Construction
1 7

3 3

2
Options

Option code J24 J24 J24

LWN 485.01-E 99/11

 Accessories and Options
Balanced bellows – subassembly item 15

LESER offers a balanced bellows design for safety valves.

AB

Balanced bellows are used for two areas of applications:

- for compensation of the effect of back pressure
- for reliable sealing of the bonnet against the blow-off chamber

FO
Compensation of the effect of back pressure pa
The back pressure exerted on the back of the disc causes a force in the AS FC
closing direction (FC). The actual amount of the force is dependent on
the diameter of the seat and the amount of back pressure. The balanced
bellows forms a surface opposite the seat that matches the seat area.
The back pressure also affects this surface and creates pressure FO in
the opening direction, which compensates for the force in the closing
direction FC.
The combination of the forces is shown in the following table:

Effective area Back pressure Effective force Direction of force Compensation curves

Seat area = AS pa FC = pa x AS closing AS = AB

Bellows area = AB pa FO = pa x AB opening FC = FO

Sealing the bonnet from the outlet chamber

LESER´s balanced bellows seal the spring chamber to the blow-off chamber. That way, they protect the guides, moving parts,
and the spring against media-related affects such as dirt, corrosion, impurities, and also temperature.

Balanced bellows
Type 431 / 433 431 / 433 PN 160 427 / 429

Design 15.2 15.2

15.2
G 1/4 G 1/4 G 1 /4

15.3 15.3 15.3

11 11 11

15.1 15.1
15.1

Bonnet spacer * * *
Bellows housing – * –
The shield protects the bellows against flow turbulence when blowing off the valve. Vibrations in the bellows are reduced.
This guarantees a longer service life of the bellows.

Control DIN ISO 228-1, G 1/4 * * *

thread ASME B1.20.1 NPT 1/2" ✓ ✓ ✓
To check the effectiveness of the bellows, an inspection connection G 1/4 is inserted into the bonnet as per DIN ISO 228-1.
For safe discharge, especially of aggressive, toxic media, a discharge pipe G 1/4 can be installed if necessary.
Option code
Standard bellows J68 J68 J68
Bonnet
Low pressure bellows J68, J63 – J68, J63
open
Special materials S15 + material name S15 + material name S15 + material name
Standard bellows J78 J78 J78
Bonnet Low pressure bellows J78, J63 – J78, J63
closed Special materials S15 + material name S15 + material name S15 + material name
Options

Control thread NPT 1/2" J95 J95 J95

The following information can be found on the respective pages of the selected valve:
– dimensions and weights, see “Dimensions and weights” table
– set pressure, see “Pressure temperature ratings” table
– temperature ranges, see “Pressure temperature ratings” table

99/12 LWN 485.01-E

Accessories and Options
Balanced bellows – subassembly item 15

Materials Standard bellows

Item Component 431 / 433, 431 / 433 PN 160, 427 / 429

1.4404
15.1 Lower adaptor
316L
1.4404
15.2 Upper adaptor
316L
1.4571
15.3 Bellows
316Ti
1.4404
11 Bonnet spacer
316L
1.4401
55 Stud
B8M
Graphite / 1.4401
60 Gasket
Graphite / 316

Bellows made of Hasteloy® or other special materials are available on request.

Balanced bellows conversion kits

With the LESER bellows conversion set, conventional construction safety valves can be converted to a balanced bellows design
quickly and easily. The conversion set contains all the components needed for the conversion as well as a conversion guide.

Conversion kits
Item Component No. Materials Remark

1 1.4404
8 Guide
316L
1 1.4404
11 Bonnet spacer
316L
1 1.4404
12 Spindle
316L
1 1.4571
15 Bellows
316Ti
4, 8 dependant on valve size 1.4401
55 Stud
B8M
2, 3 dependant on valve size Graphite / 1.4401
60 Gasket
Graphite / 316
Installation 1 LWN 037.05
Instructions

Article numbers and spare parts, see the “Spare parts” section of the respective valve type.
Options

LWN 485.01-E 99/13

 Accessories and Options
Heating jacket

Application and construction

To protect systems with viscous, crystallising or sticky media, If there is no danger of the medium setting in the blowoff
LESER offers a heating jacket. chamber of the valve, then the balanced bellows don’t have to
be used. The position of the heating connections is shown in
The heating jacket has a welded design and covers the angle figures 1 to 3.
type body such that it allows the hot media (steam, oil, and so
on) to flow through the created space.
Specification for the heating jacket
In order to protect the spindle and moving parts against The operating data of the heating jacket is placed on an
sticking, a safety valve with a balanced bellows construction additional heating jacket rating plate on the heating jacket.
should be chosen for the heating jacket construction.

For safety valves with balanced bellows, the bonnet spacer

Slip-on flange
needed to accommodate the bellows is equipped with an Heating connections with flanges are designed for better orien-
additional heating jacket. Both heating jackets are joined by a tation than slip-on flanges
threaded pipe bend.
Nominal pressure rating: PN 25 as per EN 1092-1
Class 150 as per ANSI 16.5

DN
G DN

D G A DN A
DN
B B

C C E E

1. Heating connection with flange for 2. Heating connection with coupling 3. Heating connection with flange
balanced bellows construction
Options

99/14 LWN 485.01-E

Accessories and Options
Heating jacket

Heating jacket
DNI 15 15 20 25 32 40 50 65 80 100 125 150
Inlet valve size 1/2" x 1/2" 1/2" x 1/2" 3/4" x 3/4" 1" x 1" 11/4"x11/4" 11/2"x11/2" 2" x 2" 21/2"x21/2" 3" x 3" 4" x 4" 5" x 5" 6" x 6"
Actual orifice diameter
12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Materials
Body 1.0619 1.0619 1.0619
Series 429, 433 1.4408 1.4408 1.4408 1.4408 1.4408 1.4408 1.4408 optional optional optional – –
1.4408 1.4408 1.4408
Heating jacket 1.4541
321
Connections
Option code
DN 15, 1.4571, 1.4404
H 31 PN 25
Slip-on flange 316Ti, 316L – – – –
DIN
DN 25, – 1.4571, 1.4404
H 32
PN 25 – 316Ti, 316L – –
1 2
/ ", 1.4404
K 31
Slip-on flange CL150 316L – – – –
ANSI 1", – 1.4404
K 32
CL150 – 316L – –
1.4571
H 29 G 3/8"
Coupling 316Ti – – – –
DIN 2986 – 1.4571
H 30 G 3/4"
– 316Ti – –
Heating jacket 1.4404
H 33
Bonnet spacer 316L – –

Metric units
DNE 15 15 20 25 32 40 50 65 80 100 125 150
Inlet valve size 1 2
/ " x 1/2" 1 2
/ " x 1/2" 3 4
/ " x 3/4" 1" x 1" 11/4" x 11/4" 11/2" x 11/2" 2" x 2" 21/2" x 21/2" 3" x 3" 4" x 4" 5" x 5" 6" x 6"

Actual orifice diameter

12 12 18 18 18 23 29 37 46 60 74 92
d0 [mm]
Series 433, 429 Dimensions
[mm] A 95 95 95 95 105 120 130 150 170 165 – –

B 65 65 65 65 65 75 75 80 80 80 – –

C 83 83 83 83 95 95 95 110 120 145 – –

D 131 131 130 134 142 163 180 209 224 300 – –

E 110 110 110 110 120 121 121 136 150 176 – –

Slip-on flange DN 15 15 15 15 15 15 15 15 25 25 – –

[inch] Coupling G 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/4 3/4 – –

Series 433, 429 Operating pressure [bar]

Operating 20°C 25 25 25 25 25 25 25 15 15 15 – –
temperature 300°C 18 18 18 18 18 18 18 11 11 11 – –
Options

LWN 485.01-E 99/15

 Accessories and Options
O-ring damper – subassembly item 40

The O-ring damper successfully prevents or reduces the vibra- Flutter: “Abnormal rapid reciprocating motion of the movable
tions of the moving parts of a safety valve. parts of a pressure relief valve in which the disc does
not contact the seat.“ The causes of flutter with small
and difficult to measure amplitudes are vibrations
Background: coming from external sources. Possible external
In each safety valve, the moving parts – the disc, spindle, bottom sources are piston compressors or pumps. The vibra-
spring plate and spring – form a so-called spring-mass-system. tion can be transferred to the safety valve mechani-
As in all spring-mass-systems, the components can be stimu- cally via the connections or through the medium.
lated to start vibrating under unfavourable conditions (e.g. loss
of inlet pressure). Vibrations can also be triggered by external Based on extensive experience with safety valves, LESER
units and then transferred to the safety valve via the mechani- developed the o-ring damper on its certified test benches.
cal connection or the medium. In the event of resonances, the The o-ring damper prevents the vibration of moving parts
safety valve opens and closes in an uncontrolled way at a high or reduces them to a non-critical frequency and amplitude.
frequency and can’t discharge the accorded mass flow. Nevertheless, the safety valve operates within the limits of the
rules and regulations and standards. Through a special design,
In general, there are two types of uncontrolled vibrations (defini- the o-ring damper can be used for any type of vibrations.
tion as per ASME PTC 25-2001, Chapter 2.7):
LESER offers the o-ring damper integrated in the cap H2 and
Chatter: “Abnormal rapid reciprocating motion of the movable as a modified lifting device H4. For applications with friction-
parts of a pressure relief valve in which the disc con- reducing media, e.g. oil, a balanced bellows design is provided
tacts the seat.“ The reasons for chatter may include, to protect the o-ring damper against the medium.
among other things, too high inlet pressure loss,
inadmissible back pressure, or operation in partial
load ranges.

Available design
Cap H2 Packed lever H4

Design 82

22

83

27

15
82
13
22
14
83

27 1

Conventional design J65 J66

Option
code Balanced bellows
design J65, J78 J66, J78

O-ring temperature range

-20 °C to +180 °C
Options

99/16 LWN 485.01-E

Accessories and Options
O-ring damper – subassembly item 40

Availability
Cap H2 and Packed lever H4
Valve size Pressure range
Series 433
DN 15 0.5 – 40 bar
1
/2" 7.25 – 580 psig
DN 20 – DN 50 0.5 – 40 bar
3
/4" – 2" 7.25 – 580 psig
DN 65 – DN 80 0.5 – 35 bar
21/2" – 3" 7.25 – 508psig
DN 100 0.5 – 30 bar
4" 7.25 – 435 psig
DN 15 PN 160 O-ring disc 11.3 – 103 bar
1
/2" 164 – 1494 psig
DN 15 PN 160 steel disc 9.01 – 100 bar
1
/2" 131 – 1450 psig
Series 429
DN 15 – DN 50 0.5 – 40 bar
1
/2" – 2" 7.25 – 580 psig
DN 65 – DN 80 0.5 – 35 bar
21/2" – 3" 7.25 – 508 psig
DN 100 0.5 – 30 bar
4" 7.25 – 435 psig

LESER guarantees perfect operation of the o-ring damper through extensive testing on the certified test benches. If an o-ring damper
is needed for a pressure level that is not given in the table, then further tests are necessary. This leads to longer delivery times.
Please contact [email protected].

Materials
Item. Component Cap H2 Packed lever H4

– 1.4408
1 Lever cover
– CF8M
1.4404 1.4404
2 Cap H2
316L 316L
– 1.4401
13 Cylindrical pin
– B8M
– 1.4571
14 Securing ring
– 316Ti
– 1.4404
15 Spindle
– 316L
1.4404 1.4404
22 Clamping ring
316L 316L
1.4404 –
27 Bush
316L –
– PFTE 15% Glass
27 Nozzle
– PFTE 15% Glass
1.4310 1.4310
82 Spring
Stainless steel Stainless steel
FKM FKM
83 O-Ring
FKM FKM
Options

O-ring damper Conversion kit

see respective main parts list

LWN 485.01-E 99/17

 Accessories and Options
Elastomer bellows

Application
Bellows seal the spring chamber to the blow-off chamber. That The range of applications for the elastomer bellows is limited by:
way, they protect the guides, moving parts, and the spring against – Chemical resistance
media-related affects such as dirt, corrosion, and impurities. – Medium temperature
The elastomer bellows provides a cost-effective alternative to – Set pressure
the balanced bellows. – Back pressure

Elastomer bellows

Design
71

70

72

Easy, compact, and single-ply construction facilitates installation in small blow-off chambers.
Construction
The one-piece design also facilitates easy replacement and extends the service life.

Flexibility The special shape of the elastomer bellows provides good spindle mobility and
prevents wear and tear.
To check the effectiveness of the bellows, an inspection hole (Ø 10 mm) is put into the bonnet.
Inspection hole This makes it possible to check the seal tightness of the bellows.
In the event of a fault in the bellows, the medium leaks from this hole.
Construction height No change

Materials
Valve size DN 20 – 100 DN 20 – 150
Option code J79 J87 (DN 100 J87 + S70)
Item Component
70 EPDM 281 45 NBR 670
70 Elastomer bellows
70 EPDM 281 45 NBR 670
1.4301 1.4301
71 Hose clamp
304 304
1.4301 1.4301
72 Hose clamp
304 304

Operating conditions
Temperature ranges [°C] -50 to +130 -25 to +100
Set pressure max. [barg] 10
Built-up [barg] up to 3
Options

99/18 LWN 485.01-E

Accessories and Options
Lift indicator
The lift indicator is used in the process technology to monitor the 94
operating condition of a safety valve.

Depending on the type of valve, LESER equips the packed lever H4

or the bonnets with the receptacle for the lift indicator.

For safety valves with lift indicators, the opening of the valve
during opening or the lifting operation is signalled as of a specific
lift (min. 1mm).

LESER uses inductive DC lift indicators with two-wire technology

Type DIN EN 60947-5-6 (NAMUR). The indicators are approved for
use in explosion-prone areas of Zone 0 ( II 1 D Ex iaD 20 T6).
Other indicators that meet customer specifications can be used.

Technical data for lift indicators can be found on the manufac-

turer's homepage: Packed lever H4
www.pepperl-fuchs.com

Gas-tight construction on request

For installation instructions for lift indicators, see LWN 323.02-E.

Availability
Item. Name Option code

40 Packed lever H4 with receptacle for lift indicator M!8 x 1 [mm] J39

Lift indicator
94 J93
M18 x 1, used type = PEPPERL+FUCHS NJ5-18GK-N

Functional diagram
A, closed B, open

If the safety valve opens or if the safety valve is vented

(in both cases, min. 1 mm)
For a closed valve, the lift indicator is positioned on the side,
the lift indicator changes its state and switches.
in front of the coupling or the control sleeve.
If the lift indicator unscrews, e.g. due to vibrations,
there is also a switching operation.

Valve lift, min. 1

mm / 0.04 inch
Signal

closed open
High

Low
Options

Valve opens Time

LWN 485.01-E 99/19

 Accessories and Options
Lift restriction

The Lift restriction is used to adjust the safety valve to the required discharge mass flow and does not affect the operation
of the safety valve.

A lift stopper must meet the requirements of the following codes and standards.

Requirements

Code / Standards EN ISO 4126-1, Section 5.1.3 ASME Code case 1945-4 AD 2000-Merkblatt A2, Section 10.3

≥ 30% of the full lift ≥ 30% of the full lift

Lift not less than 1.0 mm
not less than 1.0 mm not less than 2.0 mm
– – αw [S/G] ≥ 0.08
Coefficient of discharge
– – αw [L] ≥ 0.05
– Capacity replaced by
Identification of the reduced Identification of the reduced
Name plate marking “Limited capacity”
coefficient of discharge coefficient of discharge
– Limited lift =____ mm

For valves with a lift stopper to adapt to the required discharge mass flow, this device must not have an
Design according to adverse effect on the operation of the valve. If it is adjustable, the lift stopper device must be setup
EN ISO 4126-1 such that the adjustable part can be mechanically secured and sealed.
The lift stopper device must be installed and sealed by the manufacturer.

Lift restriction
Lift restriction by bush Lift restriction by gag

93
Design
96

22

Cap H2: J52

Option code J51
Packed lever H4: J50
Availability
Series 433 ✓ ✓
Series 429 – –
Materials
Item. Component

1.4404 –
22 Bush
316L –
– 1.4401
93 Stud
Accessories

– B8M
– 1.4401
96 Nut
– 8M

99/20 LWN 485.01-E

LESER worldwide
Modulate

Modulate Action
André Ramseyer AG Hong Kong LESER
Action
Flamatt, Switzerland Shenzen, China
[email protected] [email protected]
Safety Relief Valves
LESER UK
Bristol,
United Kingdom
Series 433
[email protected]

LESER Polska
Series 429
Poznan, Poland
[email protected]

LESER LLC LESER S.A.R.L.

Charlotte (NC), Toulouse, France
USA [email protected]
[email protected] LESER LLP
Singapore
[email protected]

PROTEGO–LESER do BRASIL
Rio de Janeiro, Brazil
[email protected] LESER Office FAINGER LESER Valves
Middle East Mumbai, India
Bahrain [email protected]
LESER representative [email protected]

LESER stock and local assembly

Modulate Action
Edition January 2011 / 2000
LWN 485.01-E / 0777.5646 CATALOG
The-Safety-Valve.com The-Safety-Valve.com
LESER GmbH & Co. KG 20537 Hamburg, Wendenstr. 133-135 Fon +49 (40) 251 65-100 Email: [email protected]
20506 Hamburg, P.O. Box 26 16 51 Fax +49 (40) 251 65-500 www.leser.com