Ordering number:ENN2277A

Monolithic Linear IC

LA3607

7-Band Graphic Equalizer

Features Package Dimensions

• 7-band graphic equalizer for one channel can be formed unit:mm
easily by externally connecting capacitors and variable 3021B-DIP20
resistors which fix fo (resonance frequency).
[LA3607]
• Series connection of the LA3607 makes multiband avail-
able. 20 11

• Boost, cut amount can be varied by external resistors.

7.62
6.4
• Highly stable to capacitive load.

0.25
1 10
24.2

3.9max
3.25

3.3
0.67 2.54 0.5 1.2

Specifications SANYO : DIP20

Absolute Maximum Ratings at Ta = 25˚C

Parameter Symbol Conditions Ratings Unit
Maximum Supply Voltage VCC max 20 V
Allowable Power Dissipation Pd max 300 mW
Operating Temperature Topr –20 to +75 ˚C
Storage Temperature Tstg –40 to +125 ˚C

Operating Conditions at Ta = 25˚C

Parameter Symbol Conditions Ratings Unit
Recommended Supply Voltage VCC 8 V
Operating Voltage Range VCC op 5 to 15 V

Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.

SANYO Electric Co.,Ltd. Semiconductor Company

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
12800TH (KT)/8270TS/O137KI/8236KI, TS No.2277–1/6
 LA3607

Operating Characteristics at Ta = 25˚C, VCC=8V, RL=10kΩ, Rg=600Ω, See specified Test Circuit.
Ratings
Parameter Symbol Conditions Unit
min typ max
Quiescent Current Icco Quiescent 7 9 mA
Voltage Gain VG f=1kHz, Vin=–10dB at all flat mode –3.8 –0.8 +2.2 dB
f=60Hz 10 12 14 dB
f=150Hz 10 12 14 dB
f=400Hz 10 12 14 dB
Boost Amount BOOST f=1kHz 10 12 14 dB
f=2.5kHz 10 12 14 dB
f=6kHz 10 12 14 dB
f=15kHz Vo=–10dB is taken as 10 12 14 dB
0dB at all flat mode at
f=60Hz f=1kHz. –14 –12 –10 dB
f=150Hz –14 –12 –10 dB
f=400Hz –14 –12 –10 dB
Cut Amount CUT f=1kHz –14 –12 –10 dB
f=2.5kHz –14 –12 –10 dB
f=6kHz –14 –12 –10 dB
f=15kHz –14 –12 –10 dB
Total Harmonic Distortion THD f=1kHz, Vo=1.0V at all flat mode input 0.02 0.1 %
Output Noise Voltage VNO All flat, input short, B.P.F., 10Hz to 30kHz 7 40 µV

Test Method : VCC=8V, RL=10kΩ, Rg=600Ω

Item SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 Conditions
Icco 1 F F F F F F F 2 1
VG 2 F F F F F F F 1 1 f=1kHz, VIN=–10dB
BOOST1 2 B F F F F F F 1 1 f=60Hz
BOOST2 2 F B F F F F F 1 1 f=150Hz
BOOST3 2 F F B F F F F 1 1 f=400Hz
BOOST4 2 F F F B F F F 1 1 f=1kHz
BOOST5 2 F F F F B F F 1 1 f=2.5kHz
BOOST6 2 F F F F F B F 1 1 f=6kHz
BOOST7 2 F F F F F F B 1 1 f=15kHz
CUT1 2 C F F F F F F 1 1 f=60Hz
CUT2 2 F C F F F F F 1 1 f=150Hz
CUT3 2 F F C F F F F 1 1 f=400Hz
CUT4 2 F F F C F F F 1 1 f=1kHz
CUT5 2 F F F F C F F 1 1 f=2.5kHz
CUT6 2 F F F F F C F 1 1 f=6kHz
CUT7 2 F F F F F F C 1 1 f=15kHz
THD 2 F F F F F F F 1 1 f=1kHz, Vo=1.0V
VNO 2 F F F F F F F 2 2

No.2277–2/6
 LA3607

Test Circuit

Equivalent Circuit Block Diagram

Sample Application Circuit

No.2277–3/6
 LA3607

Sample Printed Circuit Pattern (Cu-foilde side)

fo (resonance frequency)
In the sample application circuit, fo for each of 7 bands is set as follows :
fo=60Hz, 150Hz, 400Hz, 1kHz, 2.5kHz, 6kHz, 15kHz
fo is calculated using the following formula.
1
fo=
2π √ C1 · C2 · R1 · R2
Q (quality factor)
Q is calculated using the following formula.

√ C2 · R1
Q= C1 · R2

When Q is increased, the frequency band affected by the resonance circuit is narrowed and a clear distinction be-
tween this band and adjacent band is provided, but the frequency response swells greatly at all boost mode and the
peak of the composite frequency is lowered. The above must be considered to fix C1, C2.

Description of external parts

C1, C2 : Capacitors used to fix fo (resonance frequency)
C3 : Input capacitor. Decreasing the capacitor value lowers the frequency response at low frequencies.
C4 : Decoupling capacitor. Decreasing the capacitor value makes the effect of power supply stronger, whereby
repple is liable to occur.
C5 : Power capacitor.
C6 : Putput capacitor. Decreasing the capacitor value lowers the frequency response at low frequencies.

Proper cares in using IC

· Maximum supply voltage VCC max 20V must not be exceeded. The operating voltage is in the range of 5 to 15V.
· Application of power with the pin-to-pin spaces shorted causes breakdown or deterioration of the IC to occur.
When mounting the IC on the board of applying power, make sure that the pin-to-pin spaces are not shorted with
solder, etc.

No.2277–4/6
LA3607

No.2277–5/6
 LA3607

Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer's
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer's products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be expor ted without obtaining the expor t license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.

This catalog provides information as of January, 2000. Specifications and information herein are subject
to change without notice.

PS No.2277–6/6
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.