Gyro & LOG to NMEA Converter

Model SR01-40
(3rdgeneration “Lehmkuhl Repeater")

• Gyro Signal Converter “LR40” • Speed LOG to NMEA Converter

... converts old type Gyro signals such as ... converts 200 or 400 pulses per n. mile to
Synchro 360X and 90X, “Sperry Step” 6-step per NMEA Speed sentence.
deg., AnschützMicro Step and C.Plath(Sperry)
Micro Step.
• NMEA HEADING & ROT OUTPUT • ALARM Signals
... HEADING data output as NMEA or as Course ... SR01-40 has ALARM relay output:
Bus, Tokimek, Yokogawa, “Lehmkuhl” Normally Open (NO) and Normally Closed
LR22/40/60, Robertson SKR80/82 formats. (NC) Relay Contacts and the option for NMEA
alarm communication.

SR01-40 can drive several

SR01-02 Digital Heading & ROT Display units

www.ScanRepeater.com E-Mail: [email protected]

Fort Lauderdale, FL - USA * Kolbotn (Oslo) – Norway * London - UK
 SR01-40
…new generation Step/Synchro/LOG to NMEA Converter

190.0 33.0
175.0

M3-8 PAN,Poz
UP ALIGN DWN ALARM
+Flat Washer
SYNCHRO CPU +Lock Washer
STEP ALIGN
4 Places
*
LOG ALARM

141.0 128.0
+24V DC
0V DC(-)

TxD1+

TxD2+
TxD1 -

TxD2 -
RxD1+

RxD2+
RxD1 -

RxD2 -
LOG +

198.0
R+/R-

GND1

GND2
LOG -
COM
GND

NO
NC

S1
S2
S3
R1
R2

POWER ALARM LOG SYNCHRO / STEP SERIAL-1 SERIAL-2

P1 P2 P3 P4 P5

M5 GROUNDING Bolt

31.0

TIE-WRAPs
TIE-WRAPs

MAINS POWER ALIGN BUTTON LOG INPUT

A separate Button is provided to put the unit in
24V DC +30%, - 20% * Max 2 Watt ALIGN Mode. Then each digit can be adjusted up or SR01-40 accepts 200 or 400 pulses per nautical mile and converts to
The SR01-40 has no ON/OFF switch. down by the arrow buttons. Align Button and the UP NMEA Speed output.
ARROW (↑) and the DOWN ARROW (↓).
PHYSICAL SECIFICATION DATA (NMEA) INPUT / OUTPUT
ALARM BUTTON
Temp. (operational): -15 deg C / +55 deg C SR01-40 has a dedicated ALARM REST button for The SR01-40 has two independent Full Duplex Communication Channels.
Physical Protection: IP22 acknowledging and re-setting any alarms NOTE: Both data INPUT and OUTPUT are fully isolated.

GENERAL DESCRIPTION ALARMS NMEA PROTOCOLS supported

$HEHDT,xxx.x,a*hh<CR><LF>
The SR01-40 is a low cost, high quality unit for Alarms are displayed by activating the ALARM LED, $--THS,xxx.x,a*hh<CR><LF>
converting old type Gyrocompass and Speed the ALARMA RELAY and by Flashing an Alarm $--HDM,xxx.x,a*hh<CR><LF>
LOG signals to NMEA. Code in main Display. $--ROT,x.x,a *hh<CR><LF>
SR01-04 also computes Rate of Turn (ROT) and The ALARM Relay has one Normally Open Contact Speed protocol (Output):
you can elect to output the NMEA ROT sentence $--VBW,x.x,,A,,,,,,,*hh
(NO) and one Normally Closed (NC) contact. NMEA
in addition to the NMEA HEADING sentence $--VHW,x.x,T,x.x,M,x.x,N,x.x,K*hh<CR><LF>
ALARM communication is also available. SR01-40
has NO sound alarm. Sperry proprietary protocol:
The SR01-40 can also be used as a Protocol and $PPLAN,,,,,,,,a*hh<CR><LF>.
Baude Rate Converter. SET-UP PROGRAMMING Yokogawa old NMEA protocol:
HEADING / LOG DISPLAY Set-Up is done on 3 DIL Switches located under the $HEHRCxxxxx,-xxx*hh<CR><LF>
lid. However as noted below, the SR01-40 will adjust Tokimec / Robertson RGC11 protocol
The display shows the Gyro Heading or the LOG automatically to the applied Gyro Compass Signal STX K xxx.x L xx.x ETX.
speed as read exported on NMEA by the SR01- voltage levels and Frequencies.
40. Anschütz, Course Bus Protocol
STX <b1><b2> ..<b11><b12> .. CS ETX
GYRO COMPASS INPUT SIGNALS
NOTE that the SR01-40 must be Aligned to the Lehmkuhl LR40 Binary Protocol
Gyro Compass Heading. Synchro Signals: All 360X and 90 X Synchro
- With Alarm data
Signals.SR01-40 adjusts Automatically to the signal
OPERATION CONTROL level applied. APROVALS
UP (↑) and DOWN (↓) For 1X, 2X, 11X and 36X Synchro Signals please use
Type Approval will be provided later.
These are used for Brilliance Control and for SR01-60.
Aligning the Heading Display value DIMENSIONS in mm
6-Step per degree:(“Sperry Step”) 24, 35, 50& 70
BRILLIANCE CONTROL: volts. Positive or Negative Reference. SR01-40 Width:190 x Height: 198 x Depth: 33
Press the UP ARROW (↑) to increase brilliance adjusts Automatically to the signal level applied.
or the DOWN ARROW (↓) to decrease WEIGHT
brilliance. Anschütz Micro Step is decoded
Unit Net weight: 0.8 kg.
C. Plath (Sperry) Micro Step is decoded.
Gross Weight for Shipping: 1.0 kg

www.scanrepeater.comE-Mail: [email protected]
DOC#: SR01-40 DataSheet v1.0 Revision No: 00 - Date: 12.11.2012, 22:40:52 Page 2 of 3 pages
 SR01-40
…new generation Step/Synchro/LOG to NMEA Converter

SCANDINAVIAN MICRO SYSTEMS

Contact Page
Scandinavian Micro Systems provides a range of Navigation Instruments such as
SR01-02 Digital Heading & ROT Repeater, SR01-40 and SR01-60 Step & Synchro to
NMEA and SR03-01Mk2 Universal NMEA to analog Step or Synchro Drive unit.

SR01-60 is ideal for use with our New Heading & ROT Repeater;
SR01-02 (see picture below)

SR01-40 SR01-02

Location & Contact Name: Phone / e-mail Delivery Address

Opeegaard Naeringspark
SCANDINAVIN MICRO SYSTEM – Norway +47 6681 2740
Tollaasveien 34 – Lager
Jan Steinsland: email: [email protected]
1414 TROLLAASEN, Norway
Marina Mile Business Park
SCANDINAVIN MICRO SYSTEM – USA 2800 West State Road 84, Suite 101
+1 954 583 5700
Oddbjorn Steinsland, e-mail: [email protected] FORT LAUDERDALE,
Florida 33312, USA
c/o Stephen Ingamells
SCANDINAVIN MICRO SYSTEM – UK 13 Trinity Road
+44 20 8550 6458
Stephen Ingamells, e-mail [email protected] ILFORD, Essex- IG6 2BQ
United Kingdom

Please contact us at [email protected] or [email protected]

or visit us at www.scansys.no or www.ScanRepeater.com

www.scanrepeater.comE-Mail: [email protected]
DOC#: SR01-40 DataSheet v1.0 Revision No: 00 - Date: 12.11.2012, 22:40:52 Page 3 of 3 pages