VDM Metals GmbH

on behalf of VDM Metals International GmbH

Inspection certificate 225901/0 Page: 1/2
DIN EN 10204/01.05 3.1 printed: 17. JUN 2021
Order No. Purchase Order No.
46046067 Service-Center

ISO 9001, EN 9100

TÜVNord Approval
VDM Metals International GmbH Trademark
Stock & Service Center VDM® Alloy 601
Plettenberger Str. 2 NICROFER 6023 H
D - 58791 Werdohl 2.4851
Product
sheet, hot rolled, solution annealed, descaled, sheared

Specification Material
DIN EN 10095:2018-12 NiCr23Fe
DIN 17742:2020-12 NiCr 23 Fe
DIN 17750 05/2021
ASTM B 168 - 19 UNS N06601
ASME BPVC.II.B-2019 SB-168 UNS N06601
SAE AMS5870 REV. F UNS N06601
Item Pcs Dimension [mm] Cast Lot Delivery No.
31 6 3,000 x 2000,0 x 6000,0 154242 105167479 8682033572
33 2 4,000 x 2000,0 x 6000,0 154242 105167481 8682033572

Analysis (weight %)
Cast country of manufacturer country of melt
154242 Germany Germany
LE=combustion analysis analysed corresponding to ASTM E1019-18 (acc)
OE=optical emission analysis analysed corresponding to ASTM E1086-14 (acc), ASTM E3047-16 (acc)
RF=X-ray fluorescence spectroscopy analysed corresponding to ASTM E572-13 (acc), ASTM E1085-16 (acc), ASTM E1621-13 (acc), ASTM E2465-19 (acc)
DIN EN 10095:2018-12; DIN 17742:2020-12; ASTM B 168 - 19; ASME BPVC.II.B-2019 SB-168; SAE AMS5870 REV. F
Cast Melting Pr. C S Cr Ni Mn Si Ti Cu Fe P Al
154242 EF/VD top 0,06 0,003 22,63 60,30 0,66 0,19 0,38 0,02 R14,23 0,006 1,34
Meth LE LE RF RF RF RF RF RF RF RF
Cast Melting Pr. Co B
154242 EF/VD top 0,03 0,002
Meth RF OE
Sample Condition Tensile Test Hardness Test
solution annealed 1 DIN EN ISO 6892-1 06.2020 meth.B10 (acc) / transverse specimen 1 DIN EN ISO 6506-1 02.2015 (acc)
2 ASTM E8/E8M - 21 (acc) / transverse specimen 2 ASTM E18 - 20 (acc)
Temp Yield0.2% Yield1.0% Tensile Elongation RoA
Lot Sample No. [°C] [MPa] [MPa] [MPa] A [%] A [%] [%] HBW 2.5/187.5 /A HRBW
105167479 192-K1 1 RT 255 298 652 A 53,0 1 148 surface
105167479 192-K1 2 RT 257 657 50 54,2 2 78,2 surface
105167481 129-K1 1 RT 281 308 646 A 55,6 1 164 surface
105167481 129-K1 2 RT 278 654 50 54,7 2 78,0 surface

(acc)-marked test standards are accredited according to ISO 17025:2018

We herewith certify, that the material is in conformance with the above mentioned specifications Mark of the Inspector E

EMail [email protected]
Q *225901-0-E*
Mustafa Sezer , authorized inspection representative Date of release: 17.06.2021

This certified test report shall not be reproduced except in full, without the written approval of VDM Metals. The recording of false, fictitious or fraudulent statements or entries on the
certificate may be punished as a felony under federal law.

VDM Metals GmbH Chairman of the Supervisory Board: Bernardo Velázquez Herreros
Division Plate & Sheet Management Board: Dr. Niclas Müller (Chairman),
Plettenberger Straße 2, D-58791 Werdohl Daniel Azpitarte Zemp, Frank Morris, Rolf Schencking
Postfach 18 20, D-58778 Werdohl Commercial register: Iserlohn local court, #5327
Telephon: +49 2392 550 Company domicile: Werdohl
Internet: www.vdm-metals.com
VDM Metals GmbH
on behalf of VDM Metals International GmbH
Inspection certificate 225901/0 Page: 2/2
DIN EN 10204/01.05 3.1 printed: 17. JUN 2021
Order No. Purchase Order No.
46046067 Service-Center

Sample Condition Bend Test

solution annealed 1 ASTM E290 - 14 (acc) / transverse specimen

Bend.- Angle
Lot Sample No. Gauge [°]
105167479 192-K1 1 2,0 180 without cracks
105167479 192-K1
105167481 129-K1 1 2,0 180 without cracks
105167481 129-K1
Heat Treatment Lot
1157°C/8min./air cooling 105167479
1160°C/11min./air cooling 105167481
Spectral-analytical mix-up test / PMI check was performed to 100%: without objection
Dimensional and visual inspection performed: without objection
No mercury contamination; no Radium, Luminous or Alpha source materials were used in the manufacture or testing of the items furnished.

No weld repairs performed.

Certified quality management system for material manufacturers according to pressure equipment directive 2014/68/EU, Annex I, point 4.3 - TÜV NORD Systems
GmbH & Co. KG, Certification Body for Pressure Equipment, Notified Body, Code no. 0045

VDM Metals International GmbH has complied with all producer requirements of AS6279 and has instructed and received confirmation by its outsourced toll
manufacturer VDM metals GmbH accordingly.
The material VDM® Alloy 601 is not approved for pressure equipment application.

VDM Metals GmbH Chairman of the Supervisory Board: Bernardo Velázquez Herreros
Division Plate & Sheet Management Board: Dr. Niclas Müller (Chairman),
Plettenberger Straße 2, D-58791 Werdohl Daniel Azpitarte Zemp, Frank Morris, Rolf Schencking
Postfach 18 20, D-58778 Werdohl Commercial register: Iserlohn local court, #5327
Telephon: +49 2392 550 Company domicile: Werdohl
Internet: www.vdm-metals.com