www.Vidyarthiplus.

com
Optical and M icrowave Lab M anual

Dr. N.G.P. INSTITUTE OF TECHNOLOGY

COIMBATORE – 48.

DEPARTMENT
OF
ELECTRONICS AND COMMUNICATION ENGINEERING

OPTICAL AND MICROWAVE LABORATORY MANUAL

Class : IV B.E – ECE - A&B
Regulation : 2008
Semester : 07
Lab Code : 080290061

Prepared by Verified by
Mr.S.SHANMUG RAJU Ms.V.SANGEETHAPOORANI Dr.S.SURESH KUMAR
AP/ECE AP/ECE DIRECTOR-RESEARCH,HoD/ECE
Dr.N.G.P.IT Dr.N.G.P.IT Dr.N.G.P.IT

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

35
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

CYCLE I

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

36
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

37
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Ex No: 1 STUDY OF THE CHARACTERISTICS OF REFLEX

Date: KLYSTRON

AIM:
To Study of the characteristics of reflex klystron and to determine the electronic tuning range

EQUIPMENTS REQUIRED:
SNo. EQUIPMENT SPECIFICATION QUANTITY
1 Klystron power supply SKPS-610 1
2 Klystron tube with Klystron Mount 2K-25, XM-251 1
3 Isolator XI-621 1

4 Frequency meter XF-710 1

5 Variable Attenuator XA-520 1

6 Detector Mount XD 451 1
7 Wave Guide Stand XU-535 2

8 Oscilloscope -- 1
9 BNC Cable -- 1
10 Cooling Fan --- 1

THEORY:
The Reflex Klystron makes the use of velocity modulation to transform a continuous electron
beam into microwave power. Electron emitted from the cathode are accelerated and passed through the
positive resonator towards negative reflector, which retards and finally, reflects the electrons and
electrons turn back through the resonator. Suppose an rf-field exists between the resonators, the
electrons travelling forward will be accelerated or retarded, as the voltage at the resonator changes in
amplitude. The accelerated electrons leave the resonator at an increased velocity and the retarded
electrons will leave at the reduced velocity. The electron leaving the resonator will need different time
to return, due to change in velocities. As a result, returning electrons group together in bunches, As the
electron bunches pass through resonator, they interact with the voltage at resonator grids. If the bunches
pass the grid at such a time that

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

38
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

MODEL GRAPH:

MEASUREMENT TABLE:

REPELLER
MODE AMPLITUDE (V) FREQUENCY(GHz)
VOLTAGE(V)

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

39
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

electrons are slowed down by the voltage then energy will be delivered to the resonator and klystron
will oscillate. Fig shows the relationship between output power, frequency and reflector voltages.

The frequency is primarily determined by the dimensions of resonant cavity. Hence, by

changing the volume of resonator, mechanical tuning of Klystron is possible. Also a small frequency
change can be obtained by adjusting the reflector voltage. This is called Electronic Tuning.

PROCEDURE:
1. Set up the components and equipments as shown in fig.

2. Keep the position of variable attenuator at minimum attenuation position.

3. Set mode selector switch to FM-MOD position, FM amplitude and Fm frequency knob at mid
position, keep beam voltage knob fully anticlockwise and reflector voltage knob to fully clockwise and
Beam switch to ‘OFF’ position.

4. Keep the time/division scale of oscilloscope around 100Hz frequency measurement and volt/div to
lower scale.

5. Switch ON the Klystron Power Supply and Oscilloscope.

6. Switch ON Beam voltage switch and set beam voltage to 300V by beam voltage control knob.

7. Keep amplitude knob of FM Modulator to maximum position and rotate the reflector voltage
anticlockwise to get modes as shown in fig.2 on the oscilloscope. The horizontal axis represents axis
represents reflector voltage axis and vertical represents output power.

8. By changing the reflector voltage and amplitude of FM modulation, any mode of Klystron tube can
be seen on Oscilloscope.

RESULT:

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

40
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

SET UP FOR STUDY OF GUNN DIODE

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

41
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Ex No: 2
CHARACTERISTICS OF GUNN DIODE
Date:

AIM:
To Study of the characteristics of Gunn diode and to determine the threshold voltage that
corresponds to maximum current.

EQUIPMENTS REQUIRED:

SNo. EQUIPMENT SPECIFICATION QUANTITY

1. Gunn power supply GS-610 1

2. Gunn oscillator XM-55 1

3. Pin modulator XM-55 1

4. Isolator XI-621 1

5. Frequency meter XF-710 1

6. Variable Attenuator XA-520 1

7. Detector Mount XD-451 1

8. VSWR Meter SW-115 1

9. BNC Cable -- 1

10. Cooling Fan --- 1

11. Wave Guide Stand --- 2

PROCEDURE:
1. Set the components as shown in the fig.
2. Keep the control knobs of Gunn power supply as below

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

42
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

MEASUREMENT TABLE:

FREQUENCY(GHz)
GUNN BIAS POWER
CURRENT(mA) MICROMETER FREQUENCY
VOLTAGE(V) LEVELS(dB)
READING IN GHz

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

43
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Meter Switch - OFF

Gunn bias knob - Fully anticlockwise

PIN bias knob - Fully anticlockwise

PIN Mode frequency - Any position

3. Set the micrometer of Gunn oscillator for required frequency of operation

4. Switch ON the Gunn power supply

5. Measure the Gunn diode current corresponding to various Gunn bias voltages through the
digital panel meter and meter switch. Do not exceed the bias voltage above 10 volts

6. Tune the output in the VSWR meter through frequency control knob of modulation

7. If required then change the range db switch of VSWR meter to higher db position to get
deflection on VSWR meter. Any level can be set through variable attenuator and gain control
knob of VSWR meter.

8. Measure the frequency meter and detune it.

9. Plot the voltage and current readings on the graph as shown in fig.

10 Measure the threshold voltage which corresponds to maximum current.

Note: Do not keep Gun bias knob position at threshold position for more than 10-15 seconds
reading should be obtained as fast as possible. Otherwise due to excessive heating, gun diode
may burn.

RESULT:

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

44
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

MULTI HOLE DIRECTIONAL (MHD) COUPLER:

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

45
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Ex No: 3 STUDY OF POWER DISTRIBUTION IN

Date: DIRECTIONAL COUPLER

AIM:
To study the function of multihole directional coupler by measuring the following
parameters

i. Mainline and auxiliary-line VSWR

ii. The coupling factor and directivity of the coupler

EQUIPMENTS REQUIRED:

SNo. EQUIPMENT SPECIFICATION QUANTITY

1. Klystron power supply SKPS-610 1

2. Klystron tube with Klystron Mount 2K-25, XM-251 1

3. Isolator XI-621 1
4. Frequency meter XF-710 1

5. Variable Attenuator XA-520 1

6. Detector Mount XD 451 1

7. Matched Termination XL 400 2

8. MHD Coupler XK 620 1

9. Waveguide Stand -- 2

10. BNC Cable -- 1

11. VSWR meter -- 1

12. Cooling Fan -- 1

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

46
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

MEASUREMENT TABLE:

ATTENUATOR POWER(dB)
WITH COUPLER

FORWARD REVERSE DIRECTIVITY COUPLING

WITHOUT FACTOR
DIRECTION DIRECTION
COUPLER (dB)
i-arm Auxiliary i-arm Auxiliary (dB)
arm arm

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

47
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

THEORY:
A directional coupler is a device with which it is possible to measure the incident and
reflected wave separately. It consist of wo transmission line the main arm and auxiliary arm,
electromagnetically coupled to each other. The power entering in the main arm gets divided
between port2 and 3 and almost no power comes out in port 4. Power entering at port2 is divided
between port1 and 4.

The coupling factor is defined as

Coupling (db) = 10 log10(P1/P2)

Where port2 is terminated.

Isolation (db) = 10 log10(P2/P3)

Where P1 is matched.

With built-in termination and power entering at Port1, the directivity of the coupler is a measure
of separation between incident wave and the reflected wave.Directivity is measured indirectly,

Directivity D (db)= 10 log10(P2/P1)

Main line VSWR is SWR measured, looking into the main line input terminal when the
matched loads are placed at all other ports.

Auxiliary line VSWR is SWR measured in the auxiliary line looking into the output
terminal when the matched loads are placed on other terminals

Main line insertion loss is the attenuation introduced in the transmission line by insertion of
coupler. It is defined as

Insertion loss (dB) = 10 log10 (P1/P2)

PROCEDURE:

A. Main Line SWR Measurement

1. Set up the equipments as shown in fig

2. Energies the microwave sources for particular frequency of operation as described in

the procedures given in the operation of Klystron tube/Gunn Oscillator

3. Follow the procedure as described for VSWR measurement(low and medium SWR
measurement)

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

48
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

4. Repeat the same for other frequencies.

B. Auxiliary Line SWR Measurement

1. Set up the components and equipments as shown in fig

2. Energies the microwave sources for particular frequency of operation as described in

the operation of Klystron tube/Gunn Oscillator

3. Measure SWR as described in the experiment of SWR measurement (low and medium
SWR measurement)

4. Repeat the same for other frequencies.

C. Measurement of Coupling Factor, Insertion loss, Isolation & Directivity

1. Set up the components and equipments as shown in fig

2. Energies the microwave sources for particular frequency of operation

3. Remove the multi hole directional coupler and connect the detector mount of the
Frequency meter. Tune the Detector for maximum output.

4. Set any reference level of Power on VSWR meter with the help of variable
attenuator, Gain control knob of VSWR meter and note down the
reading (reference level let X)

5. Insert the directional coupler as shown in second fig 3. With detector to the
auxiliary port 3 and matched termination to port 2, without changing the position
of variable attenuator and gain control knob of VSWR meter

6. Note down the reading on VSWR meter on the scale with the help of range – dB
switch if required. let it be Y

7. Calculate coupling factor which will be X-Y=C(dB)

8. Now carefully disconnect the detector from the auxiliary port 3 and match
termination from port 2 without disturbing the set-up

9. Connect the matched termination to the auxiliary port 3 and detector to port 2 and
measure the reading on VSWR meter, Suppose it is Z.

10. Compute the insetiopn loss X-Z dB

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

49
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

11. Repeat the steps from 1 to 4.

12. Connect the directional coupler in the reverse direction i.e., port 2 to frequency
meter side. Matched termination to port 1 and detector mount to prt 3 without
disturbing the position of the variable attenuator and gain control knob of VSWR
meter.

13. Measure and note down the reading on VSWR meter. Let it be Yd. X- Yd gives
Isolation (dB)

14. Compute the Directivity as Y-Yd= I-C

15. Repeat the same for other frequencies.

RESULT:

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

50
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

51
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Ex No: 4 STUDY OF POWER DISTRIBUTION IN MAGIC

Date: TEE

AIM:

Study of Magic Tee

EQUIPMENTS REQUIRED:

SNo. EQUIPMENT SPECIFICATION QUANTITY

1. Klystron power supply SKPS-610 1

2. Klystron tube with Klystron Mount 2K-25, XM-251 1

3. Isolator XI-621 1
4. Frequency meter XF-710 1

5. Variable Attenuator XA-520 1

6. Detector Mount XD 451 1

7. Matched Termination XL 400 2

8. Magic Tee XK 620 1

9. Waveguide Stand -- 2

10. BNC Cable -- 1

11. VSWR meter -- 1

12. Cooling Fan -- 1

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

52
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

MEASUREMENT TABLE:

Pin = ______dB

SCATTERING
PARAMETER
VSWR METER
ORIENTATION OF MAGIC TEE READING (dB)

INPUT ARM OUTPUT ARM OUTPUT POWER(dB)

P01 P12

P13(E-Plane)

P14(H-Plane)

P02 P21

P23(E-Plane)

P24(H-Plane)

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

53
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

THEORY:

The device magic Tee is a combination of E and H palne Tee. Arm 3 is the H-arm and
arm 4 is the E-arm. If the power is fed into arm 3 (H-arm) the electric field divides equally
between arm 1 and 2 wih the same phase, and no electric field exists in arm 4. If power is fed in
arm 4(E-arm). It divides equally into arm and 2 but out of phase with no powerto arm 3. Further,
if power is fed in arm 1 and 2 simultaneously it is added in arm 3 (H-arm) and it is subtracted in
E-arm i.e arm 4

The basic parameters to be measured for magic Tee are defined below

A. Input VSWR

Value of SWR corresponding to each port, as a load to the line while other ports are
terminated in matched load.

B. Isolation

The Isolation between E and H arms is defined as the ration of the power supplied by the
generator connected to the E-arm (port 4) to the power detected at H-arm (port3) when
side arms 1 and 2 terminated in matched load.

Hence Isolation (dB) = 10 log10(P4/P3)

Similarly, isolation between other ports may also be defined.

C. COUPLING FACTOR

It is defined as Cij= 10-α/20

Where α is the attenuation / isolation in dB when I is input arm and j is output

arm

Thus α=10 log10(P4/P3)

Where P3 is the power delievered to arm I and P4 is power detected at j arm

PROCEDURE:
A.VSWR MEASUREMENTS AT PORTS

1. Set up the components and equipments as shown in fig. Keeping E arm towards slotted
line and match the termination to other ports.

2. Energise the microwave sources for particular frequency of operation

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

54
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

3. Measure VSWR of E arms as described in measurement of SWR for low and medium
value

5. Connect another arm to slotted line and terminate the other port with matched
termination. Measure the VSWR as above. Similarly, VSWR of any port can be
measured.

B. Measurement of Isolation and Coupling factor

1. Remove the tunable probe and magic Tee from the slotted line and connect the detector
mount to slotted line.

2. Energise the microwave sources for particular frequency of operation and tune the
detector mount for maximum output

3. With the help of variable attenuator and gain control knob of VSWR meter, set any
power level in VSWR meter and note down. Let it be P3.

4. Without disturbing the position of variable attenuator and gain control knob, carefully
place the Magic Tee after slotted line. Keeping H arm connected to slotted line,
detector to E arm and matched termination to arm 1 and 2. Note down the reading of
VSWR meter. Let it be P4.

5. Determine the Isolation between port 3 and 4 as P3-P4 in dB.

6. Determine th e coupling coefficient from equation given in the theory part.

7. The same experiment may be repeated for other ports also.

8. Repeat the above experiment fo r other frequencies.

RESULT:

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

55
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

56
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Ex No: 5
MEASUREMENT OF THE GAIN AND POLAR
Date: PATTERN OF HORN ANTENNA

AIM:
To measure the polar pattern and the gain of a waveguide horn antenna.

EQUIPMENTS REQUIRED:
SNo. EQUIPMENT SPECIFICATION QUANTITY
1 Klystron power supply SKPS-610 1
2 Klystron tube with Klystron Mount 2K-25, XM-251 1
3 Isolator XI-621 1

4 Frequency meter XF-710 1

5 Variable Attenuator XA-520 1

6 Detector Mount XD 451 1
7 Wave Guide Stand XU-535 2

8 Oscilloscope -- 1
9 BNC Cable -- 1
10 Cooling Fan --- 1

THEORY:
If a transmission line, propagating energy is left open at one end , there will be radiation
from this end. In case of a rectangular waveguide this antenna presents a mismatch of about 2
and it radiates in many directions. The match will improve if the open waveguide is a horn
shape.

The radiation pattern of an antenna is a plot of field strength of the power intensity as a
function of the aspect angle at a constant distance from the radiating antenna. An antenna pattern
is ofcourse three dimensional but for practical reasons it is normally presented as a two

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

57
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

MEASUREMENT TABLE:
Frequency =

S =

ANGLE (degrees) VT (v) VR (v) GAIN

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

58
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

dimensional pattern in one or several planes. An antenna pattern consists of several lobes , the
main lobe, side lobes and the back lobe. The major power is concentrated in the main lobe and it
is required to keep the power in the side lobes and back lobe as low as possible. The power
intensity at the maximum in the main lobe compared to the power intensity achieved from an
imaginary omnidirectional antenna (radiating equally in all directions) with the same power fed
to the antenna is defined as gain of the antenna.

3db beam width

This is the angle between the two poits on a main lobe where the power intensity is half
the maximum power intensity. The antenna pattern measurement is always done in far field
region.

Far field pattern is achieved at a minimum distance of

2D2
-----
(for rectangular Horn “Antenna”)
λ0
Where D is size of the broad wall of horn aperture and λ0 is free space wave length.

It is also very important to avoid reflection; antenna measurement is done at outdoor

ranges or in anechoic chambers made of absorbing materials.

Antenna measurements are mostly made with unknown antenna as receiver, therefore
several methods are there to measure the gain of antenna. One method is to compare the
unknown antenna with standard gain antenna with known gain. Another method is to use two
identical antennas. One as a transmitter and other as receiver and from following formula the
gain can be calculated.

Ptλ0G1 G2
Pr = --------------------
(4πS) 2
Where Pt is transmitted power, Pris received power, G1, G2 is gain of transmitting and
receiving antenna, S is the radial distance between two antennas.

λ0 is free space wavelength.

If both transmitting and receiving antennas are identical having gain G then,
Ptλ0 G2
Pr = --------------------;
(4πS)2

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

59
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

In the above equation and can be measured and gain can be computed .As from the above
equation it is not necessary to know the absolute value of Pr and Pt. Only ratio is required which
can be measured by VSWR meter.

PROCEDURE

A. Antenna Radiation Pattern

1. Setup the equipments as shown in the figure1. Keeping the axis of both antenna in same
line.
2. Energize the Gunn Oscillator for maximum output at desired frequency with square wave
modulation by tuning square wave amplitude and frequency of modulating signal of
Gunn Power Supply and by tuning the detector.
3. Also tune the S S tuner in the line for maximum output ( if S STunner is in the setup)
4. Obtain full scale deflection (0db) on normal db scale (0-1-db) at any convenient range
swith position of the VSWR meter by gain control knob of VSWR meter or by variable
attenuator.
5. Tune the receiving horn to the left in 2 or 5 steps upto 4-5 and note the corresponding
VSWR db reading in normal db range. When necessary , change the range switch to next
higher range and add 10 db to the observed value.
6. Repeat the above step but this time turn the receiving horn to the right and note down the
readings.
7. Plot a relative power pattern i.e. output vs. angle.
8. From diagram determine 3db width (beam width) of the horn antenna.

B. Gain Measurement

1. Setup the equipments as shown in the figure1. Both horns should be in line.
2. Keep the range db switch meter at 50db position with gain control full.
3. E Energize the Gunn Oscillator for maximum output at desired frequency with
modulating amplitude and frequency of Gunn Power Supply and by tuning of detector.
4. Obtain full scale deflection in VSWR meter with variable attenuator.
5. Replace the transmitting horn by detector mount and change the appropriate db position
to get the deflection. On scale (do not touch the gain control knob). Note and record the
range db position and deflection of VSWR meter,
6. Calculate the difference in db between the power measured in steps 4 and 5.

RESULT

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

60
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

61
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Ex No: 6 DETERMINTAION OF GUIDE

WAVELENGTH, FREQUENCY
Date:
MEASUREMENT

AIM:
To determine the frequency and wavelength in a rectangular waveguide working in TE
mode.

EQUIPMENT:

SNo. EQUIPMENT SPECIFICATION QUANTITY

1 Klystron power supply SKPS-610 1
2 Klystron tube with Klystron Mount 2K-25, XM-251 1
3 Isolator XI-621 1

4 Frequency meter XF-710 1

5 Variable Attenuator XA-520 1

6 Slotted section XS 651 1
7 Tunable Probe XP-655 1

8 VSWR Meter SW-115 1

9 Movable Short XT-4813 1
10 Wave Guide Stand XU-535 2

11 Matched Termination XL-400 1

12 Oscilloscope -- 1

13 BNC Cable -- 1

14 Cooling Fan --- 1

THEORY
For dominant TE mode rectangular waveguide Io,Igand Ic are related as below

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

62
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

(1/⅄o2) = (1/⅄g2) + (1/⅄c2)

where Io is free space wavelength

Ig is guide wavelength

Ic is cutoff wavelength

For TE mode, I =2a where “a” is broad dimension of waveguide.

PROCEDURE
1. Setup the components and equipments as shown in figure.
2. Setup variable attenuator at minimum attenuation position.
3. Keep the control knobs of VSWR meter as below:
Range-50db
Input switch- crystal low impedance
Meter switch-normal position
Gain(Coarse & Fine)- Mid position
4. Keep the control knobs of Klystron power supply as below
Beam voltage- OFF
Mod-switch-AM
Beam Voltage knob-Fully anticlockwise
Reflector Voltage- Fully clockwise
AM- Amplitude knob- Around fully clockwise
AM- Frequency knob – Around Mid position
5. Switch ON the Klystron power supply, VSWR Meter and cooling fan switch.
6. Switch ON the beam voltage switch and set beam voltage around 250V-300V with help
of beam voltage knob.
7. Adjust the reflector voltage to get some deflection in VSWR meter.
8. Maximize the deflection with AM amplitude and frequency control knob of power
supply.
9. Tune the plunger of Klystron Mount for maximum deflection.
10. Tune the reflector voltage knob for maximum deflection .
11. Tune the probe for maximum deflection in VSWR Meter.
12. Tune the frequency meter knob to get a ‘dip’ on the VSWR scale and note down the
frequency directly from frequency meter.
13. Replace the Termination with movable short, and detune the frequency meter.
14. Move the probe along the slotted line. The deflection in VSWR meter will vary. Move
the probe to a minimum deflection position, to get accurate reading. If necessary increase
the VSWR Meter range dbswitch to higher position. Note and record the probe position.
15. Move the probe to next minimum position and record the probe position again.

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

63
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

16. Calculate the guide wavelength as twice the distance between two successive minimum
position obtained as above.
17.
18. Measure the waveguide inner broad dimension ‘a’ which will be around 22.86 mm for X-
band.
19. Calculate the frequency by following equation

20. Verify the frequency obtained by frequency meter.

21. Above experiment can be verified at different frequencies.

RESULT:

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

64
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

65
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Ex No: 7 IMPEDANCE MEASUREMENT BY

Date: SLOTTED LINE METHOD

AIM:
To measure an unknown impedance using the smith chart.

EQUIPMENTS:

SNo. EQUIPMENT SPECIFICATION QUANTITY

1 Klystron power supply SKPS-610 1
2 Klystron tube with Klystron Mount 2K-25, XM-251 1
3 Isolator XI-621 1

4 Frequency meter XF-710 1

5 Variable Attenuator XA-520 1

6 Slotted section XS 651 1
7 Tunable Probe XP-655 1

8 VSWR Meter SW-115 1

9 Movable Short XT-4813 1
10 Wave Guide Stand XU-535 2

11 Matched Termination XL-400 1

12 S S Tuner XT 441

13 Oscilloscope -- 1

14 BNC Cable -- 1

15 Cooling Fan --- 1

THEORY:
The impedance at any point on a transmission line can be written in the form R+jX

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

66
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

For comparison SWR can be calculated

Where

Reflection co-efficient

Z0= characteristics impedance of w/g at operating frequency

Z= load impedance. The measurement is performed in following way.

The unknown device is connected to the slotted line and the position of one minima is
determined. The unknown device is replaced by movable short to the slotted line . Two
successive minima positions are noted.The twice of the difference between minima position will
be guidewave length. One of the minima is used as reference for impedance measurement .find
the difference of reference minima and minima position obtained from unknown load. Let it be
‘d’. Take a smith chart , taking ‘1’ as centre, draw a circle of radius equal to S. mark a point on
circumference of smith chart towards load side at a distance equal to d/g. join the centre with this
point . find the point where it cut the drawn circle.the co-ordinates of this point will show the
normalized impedance of load.

PROCEDURE:
1. Setup the components and equipments as shown in figure.
2. Setup variable attenuator at minimum attenuation position.
3. Keep the control knobs of VSWR meter as below:
Range - 50db position
Input switch - Crystal low impedance
Meter switch - Normal position
Gain(Coarse & Fine)- Mid position
4. Keep the control knobs of Klystron power supply as below
Beam voltage - ‘OFF’
Mod-switch -AM
Beam Voltage knob-Fully anticlockwise

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

67
www.Vidyarthiplus.com
 www.Vidyarthiplus.com
Optical and M icrowave Lab M anual

Reflector Voltage- Fully clockwise

AM- Amplitude knob- Around fully clockwise
AM- Frequency knob – Around Mid position
5. Switch ‘ON’ the Klystron power supply, VSWR Meter and cooling fan switch.
6. Switch ‘ON’ the beam voltage switch and set beam voltage around 250V-300V with help
of beam voltage knob.
7. Adjust the reflector voltage to get some deflection in VSWR meter.
8. Maximize the deflection with AM amplitude and frequency control knob of power
supply.
9. Tune the plunger of Klystron Mount for maximum deflection.
10. Tune the reflector voltage knob for maximum deflection .
11. Tune the probe for maximum deflection in VSWR Meter.
12. Tune the frequency meter knob to get a ‘dip’ on the VSWR scale and note down the
frequency directly from frequency meter.
13. Keep the depth of pin S S. Tuner to around 3-4 mm and lock it.
14. Move the probe along the slotted line to get maximum deflection.
15. Adjust VSWR meter gain control knob and variable attenuator until the meter indicates
1.0 on the normal db SWR scale.
16. Move the probe to next minimum position and note down the SWR S0 on the scale .also
note down the probe position. Let it be ‘d’.
17. Remove the SS tuner and matched termination and place movable short at slotted line.
The plunger of short should be at zero.
18. Note the position of two successive minima position .let it be as d1 and d2 .Hence λg =
2(d1- d2).
19. Calculate

d
-----
λg

20. Find out the normalized impedance as described in the theory section.
21. Repeat the same experiment for other frequency if required.

RESULT:

Dr .NGP INSTITUTE OF TECHNOLOGY DEPT: ECE YEAR & SEM : IV & 07

68
www.Vidyarthiplus.com