Scribd
Upload
76 views1 page

FT918BBI (1) Cheque Nipco

Uploaded by

Roberto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
76 views1 page

FT918BBI (1) Cheque Nipco

Uploaded by

Roberto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

www.nibco.

com
AHEAD OF THE F L O W® Revised 9/28/2009

Class 125 Iron Body Check Valves


Bolted Bonnet • Horizontal Swing • *Renewable Seat and Disc

125 PSI/8.6 Bar Saturated Steam to 353º F/178º C


200 PSI/13.8 Bar Non-Shock Cold Working Pressure
to -20º F to 150º F/-29º C to 66º C◆

CONFORMS TO MSS SP-71 TYPE 1


MATERIAL LIST F-918-B
PART SPECIFICATION Flanged
1. Body Bolt Steel ASTM A 307
2. Identification Plate Aluminum
3. Bonnet Cast Iron ASTM A 126 Class B T-918-B
4. Body Gasket Synthetic Fibers Threaded
5. Body Nut Steel ASTM A 307
6. Side Plug Brass ASTM B 16 Alloy C36000
7. Hanger Pin Brass ASTM B 16 Alloy C36000
8. 2 Hanger Ductile Iron ASTM A 536
Cast Bronze ASTM B 584 Alloy C84400
9. 1 Disc or ASTM A 536 Ductile Iron with
Bronze Face Ring
10. Seat Ring Cast Bronze ASTM B 584 Alloy C84400
11. Disc Nut Brass ASTM B 16 Alloy C36000
12. Body Cast Iron ASTM A 126 Class B
13. 1 Disc Bolt Brass ASTM B 16 Alloy C36000
14. Disc Plate Cast Iron ASTM A 126 Class B
15. Disc Cage Cast Iron ASTM A 126 Class B
1 2" thru 4" have Bronze ASTM B 62 Disc.

5" thru 12" have Iron Disc with Bronze Disc Face Rings and Disc Bolt.
2 10" is Ductile Iron ASTM A 536. F-918-B
Flg x Flg

DIMENSIONS—WEIGHTS—QUANTITIES
Dimensions
F-918-B T-918-B
Size A A B D E F-918-B T-918-B
In. mm. In. mm. In. mm. In. mm. In. mm. In. mm. Lbs. Kg. Lbs. Kg.
2 50 8.00 203 6.50 165 3.94 100 6.00 152 .63 16 24 11 15 7
2¹⁄₂ 65 8.50 216 7.50 191 4.50 114 7.00 178 .69 17 35 16 26 12
3 80 9.50 241 8.00 203 5.13 130 7.50 191 .75 19 47 21 31 14
4 100 11.50 292 9.38 238 6.13 156 9.00 229 .94 24 80 36 54 24
5 125 13.00 330 x x 6.81 173 10.00 254 .94 24 100 45 80 36
6 150 14.00 356 x x 8.00 203 11.00 279 1.00 25 146 66 121 54
8 200 19.50 495 x x 9.44 240 13.50 343 1.13 29 274 124 x x
10 250 24.50 622 x x 12.06 306 16.00 406 1.19 30 426 193 x x
12 300 27.50 699 x x 16.13 410 19.00 483 1.25 32 675 306 x x
Note: On pump discharge, the preferred check valves are: T-918
- inline, spring assisted, center-guided, lift checks NPT x NPT
- spring assisted twin (double) disc
- swing design with lever and weight or lever and spring
You should also install the check valve as for far from the pump as possible and at a minimum length of 5
times the pipe diameter. Flow straighteners may be required.
* Proper machining facilities required.
WARNING: Do not use for Reciprocating Air
x Not available this size. Compressor Service.
2¹⁄₂" thru 12" are available with lever and weight or lever and spring.
NIBCO Iron Body Check Valves may be installed
◆For detailed Operating Pressure, refer to Pressure Temperature Chart on page 111. in both horizontal and vertical lines with upward
flow or in any intermediate position.

NIBCO INC. WORLD HEADQUARTERS • 1516 MIDDLEBURY ST. • ELKHART, IN 46516-4740 • USA • PH: 1.800.234.0227
TECH SERVICES PH: 1.888.446.4226 • FAX: 1.888.234.0557 • INTERNATIONAL OFFICE PH: +1.574.295.3327 • FAX: +1.574.295.3455 63
www.nibco.com

You might also like