Bounded or Guided Transmission

Media
Guided media, which are those that provide a conduit from one device to another,
include Twisted-Pair Cable, Coaxial Cable, and Fibre-Optic Cable.
A signal travelling along any of these media is directed and contained by the physical
limits of the medium. Twisted-pair and coaxial cable use metallic (copper) conductors
that accept and transport signals in the form of electric current. Optical fibre is a cable
that accepts and transports signals in the form of light.

Twisted Pair Cable

This cable is the most commonly used and is cheaper than others. It is lightweight,
cheap, can be installed easily, and they support many different types of network. Some
important points :

 Its frequency range is 0 to 3.5 kHz.

 Typical attenuation is 0.2 dB/Km @ 1kHz.
 Typical delay is 50 µs/km.
 Repeater spacing is 2km.

A twisted pair consists of two conductors(normally copper), each with its own plastic
insulation, twisted together. One of these wires is used to carry signals to the receiver,
and the other is used only as ground reference. The receiver uses the difference
between the two. In addition to the signal sent by the sender on one of the wires,
interference(noise) and crosstalk may affect both wires and create unwanted signals. If
the two wires are parallel, the effect of these unwanted signals is not the same in both
wires because they are at different locations relative to the noise or crosstalk sources.
This results in a difference at the receiver.
Twisted Pair is of two types:

 Unshielded Twisted Pair (UTP)

 Shielded Twisted Pair (STP)
Unshielded Twisted Pair Cable
It is the most common type of telecommunication when compared with Shielded
Twisted Pair Cable which consists of two conductors usually copper, each with its own
colour plastic insulator. Identification is the reason behind coloured plastic insulation.
UTP cables consist of 2 or 4 pairs of twisted cable. Cable with 2 pair use RJ-
11 connector and 4 pair cable use RJ-45 connector.

Advantages of Unshielded Twisted Pair Cable

 Installation is easy
 Flexible
 Cheap
 It has high speed capacity,
 100 meter limit
 Higher grades of UTP are used in LAN technologies like Ethernet.

It consists of two insulating copper wires (1mm thick). The wires are twisted together in
a helical form to reduce electrical interference from similar pair.

Disadvantages of Unshielded Twisted Pair Cable

  Bandwidth is low when compared with Coaxial Cable
 Provides less protection from interference.

Shielded Twisted Pair Cable

This cable has a metal foil or braided-mesh covering which encases each pair of
insulated conductors. Electromagnetic noise penetration is prevented by metal casing.
Shielding also eliminates crosstalk (explained in KEY TERMS Chapter).
It has same attenuation as unshielded twisted pair. It is faster the unshielded and
coaxial cable. It is more expensive than coaxial and unshielded twisted pair.

Advantages of Shielded Twisted Pair Cable

 Easy to install
 Performance is adequate
 Can be used for Analog or Digital transmission
 Increases the signalling rate
 Higher capacity than unshielded twisted pair
 Eliminates crosstalk
Disadvantages of Shielded Twisted Pair Cable

 Difficult to manufacture
 Heavy

Performance of Shielded Twisted Pair Cable

One way to measure the performance of twisted-pair cable is to compare attenuation
versus frequency and distance. As shown in the below figure, a twisted-pair cable can
pass a wide range of frequencies. However, with increasing frequency, the attenuation,
measured in decibels per kilometre (dB/km), sharply increases with frequencies above
100kHz. Note that gauge is a measure of the thickness of the wire.

Applications of Shielded Twisted Pair Cable

 In telephone lines to provide voice and data channels. The DSL lines that are
used by the telephone companies to provide high-data-rate connections also use
the high-bandwidth capability of unshielded twisted-pair cables.
  Local Area Network, such as 10Base-T and 100Base-T, also use twisted-pair
cables.

Coaxial Cable
Coaxial is called by this name because it contains two conductors that are parallel to
each other. Copper is used in this as centre conductor which can be a solid wire or a
standard one. It is surrounded by PVC installation, a sheath which is encased in an
outer conductor of metal foil, barid or both.
Outer metallic wrapping is used as a shield against noise and as the second conductor
which completes the circuit. The outer conductor is also encased in an insulating
sheath. The outermost part is the plastic cover which protects the whole cable.
Here the most common coaxial standards.

 50-Ohm RG-7 or RG-11 : used with thick Ethernet.

 50-Ohm RG-58 : used with thin Ethernet
 75-Ohm RG-59 : used with cable television
 93-Ohm RG-62 : used with ARCNET.
Coaxial Cable Standards
Coaxial cables are categorized by their Radio Government(RG) ratings. Each RG
number denotes a unique set of physical specifications, including the wire gauge of the
inner conductor, the thickness and the type of the inner insulator, the construction of the
shield, and the size and type of the outer casing. Each cable defined by an RG rating is
adapted for a specialized function, as shown in the table below:

Coaxial Cable Connectors

To connect coaxial cable to devices, we need coaxial connectors. The most common
type of connector used today is the Bayonet Neill-Concelman (BNC) connector. The
below figure shows 3 popular types of these connectors: the BNC Connector, the BNC
T connector and the BNC terminator.
The BNC connector is used to connect the end of the cable to the device, such as a TV
set. The BNC T connector is used in Ethernet networks to branch out to a connection to
a computer or other device. The BNC terminator is used at the end of the cable to
prevent the reflection of the signal.
There are two types of Coaxial cables:
1. BaseBand
This is a 50 ohm (Ω) coaxial cable which is used for digital transmission. It is mostly
used for LAN's. Baseband transmits a single signal at a time with very high speed. The
major drawback is that it needs amplification after every 1000 feet.

2. BroadBand
This uses analog transmission on standard cable television cabling. It transmits several
simultaneous signal using different frequencies. It covers large area when compared
with Baseband Coaxial Cable.

Advantages of Coaxial Cable

 Bandwidth is high
 Used in long distance telephone lines.
 Transmits digital signals at a very high rate of 10Mbps.
 Much higher noise immunity
 Data transmission without distortion.
 The can span to longer distance at higher speeds as they have better shielding
when compared to twisted pair cable

Disadvantages of Coaxial Cable

 Single cable failure can fail the entire network.

 Difficult to install and expensive when compared with twisted pair.
 If the shield is imperfect, it can lead to grounded loop.
Performance of Coaxial Cable
We can measure the performance of a coaxial cable in same way as that of Twisted
Pair Cables. From the below figure, it can be seen that the attenuation is much higher in
coaxial cable than in twisted-pair cable. In other words, although coaxial cable has a
much higher bandwidth, the signal weakens rapidly and requires the frequent use of
repeaters.

Applications of Coaxial Cable

 Coaxial cable was widely used in analog telephone networks, where a single
coaxial network could carry 10,000 voice signals.
 Cable TV networks also use coaxial cables. In the traditional cable TV network,
the entire network used coaxial cable. Cable TV uses RG-59 coaxial cable.
 In traditional Ethernet LANs. Because of it high bandwidth, and consequence
high data rate, coaxial cable was chosen for digital transmission in early Ethernet
 LANs. The 10Base-2, or Thin Ethernet, uses RG-58 coaxial cable with BNC
connectors to transmit data at 10Mbps with a range of 185 m.

Fiber Optic Cable

A fibre-optic cable is made of glass or plastic and transmits signals in the form of light.
For better understanding we first need to explore several aspects of the nature of light.
Light travels in a straight line as long as it is mobbing through a single uniform
substance. If ray of light travelling through one substance suddenly enters another
substance (of a different density), the ray changes direction.
The below figure shows how a ray of light changes direction when going from a more
dense to a less dense substance.

Bending of a light ray

As the figure shows:

 If the angle of incidence I(the angle the ray makes with the line perpendicular to
the interface between the two substances) is less than the critical angle, the
ray refracts and moves closer to the surface.
 If the angle of incidence is greater than the critical angle, the ray reflects(makes
a turn) and travels again in the denser substance.
  If the angle of incidence is equal to the critical angle, the ray refracts and moves
parallel to the surface as shown.

Note: The critical angle is a property of the substance, and its value differs from one
substance to another.
Optical fibres use reflection to guide light through a channel. A glass or plastic core is
surrounded by a cladding of less dense glass or plastic. The difference in density of the
two materials must be such that a beam of light moving through the core is reflected off
the cladding instead of being refracted into it.

Internal view of an Optical fibre

Propagation Modes of Fiber Optic Cable

Current technology supports two modes(Multimode and Single mode) for propagating
light along optical channels, each requiring fibre with different physical characteristics.
Multimode can be implemented in two forms: Step-index and Graded-index.
Multimode Propagation Mode
Multimode is so named because multiple beams from a light source move through the
core in different paths. How these beams move within the cable depends on the
structure of the core as shown in the below figure.
  In multimode step-index fibre, the density of the core remains constant from
the centre to the edges. A beam of light moves through this constant density in a
straight line until it reaches the interface of the core and the cladding.
The term step-index refers to the suddenness of this change, which contributes
to the distortion of the signal as it passes through the fibre.
 In multimode graded-index fibre, this distortion gets decreases through the
cable. The word index here refers to the index of refraction. This index of
refraction is related to the density. A graded-index fibre, therefore, is one with
varying densities. Density is highest at the centre of the core and decreases
gradually to its lowest at the edge.

Single Mode
Single mode uses step-index fibre and a highly focused source of light that limits
beams to a small range of angles, all close to the horizontal. The single-mode fibre itself
is manufactured with a much smaller diameter than that of multimode fibre, and with
substantially lower density.
The decrease in density results in a critical angle that is close enough to 90 degree to
make the propagation of beams almost horizontal.

Fibre Sizes for Fiber Optic Cable

Optical fibres are defined by the ratio of the diameter or their core to the diameter of
their cladding, both expressed in micrometers. The common sizes are shown in the
figure below:

Fibre Optic Cable Connectors

There are three types of connectors for fibre-optic cables, as shown in the figure below.
The Subscriber Channel(SC) connector is used for cable TV. It uses push/pull locking
system. The Straight-Tip(ST) connector is used for connecting cable to the networking
devices. MT-RJ is a connector that is the same size as RJ45.

Advantages of Fibre Optic Cable

Fibre optic has several advantages over metallic cable:

 Higher bandwidth
 Less signal attenuation
 Immunity to electromagnetic interference
 Resistance to corrosive materials
 Light weight
 Greater immunity to tapping

Disadvantages of Fibre Optic Cable

There are some disadvantages in the use of optical fibre:
  Installation and maintenance
 Unidirectional light propagation
 High Cost

Performance of Fibre Optic Cable

Attenuation is flatter than in the case of twisted-pair cable and coaxial cable. The
performance is such that we need fewer(actually one tenth as many) repeaters when
we use the fibre-optic cable.

Applications of Fibre Optic Cable

 Often found in backbone networks because its wide bandwidth is cost-effective.

 Some cable TV companies use a combination of optical fibre and coaxial cable
thus creating a hybrid network.
 Local-area Networks such as 100Base-FX network and 1000Base-X also use
fibre-optic cable.