Bulletin 2101/ 2107

MODEL 2101

HIGH CAPACITY
GAS CHLORINATOR

The principal use of the REGAL Gas Chlorinator is to CAPACITIES

chlorinate water, wastewater and industrial process water Dual scale metering tubes with maximum capacities of 1000 and 2000 pounds
with gas chlorine. The simple, efficient design has made per 24 hours of chlorine gas with corresponding metric scales of 20 and 40 kilograms
REGAL Gas Chlorinators the industry standard. Built with per hour. The minimum feed rate is 1/20th of maximum for each metering tube.
heavy duty corrosion resistant parts, REGAL Chlorinators
provide safe, long-lasting service. FLOW RATE ADJUSTMENT
Manually adjustable by means of a flow rate control valve located at the top
The REGAL Model 2101 Gas Chlorinators are totally vacuum-
of the flow meter. Flow rate is then regulated by a special spring-opposed
operated solution feed type, for high chlorine gas feed rates up
diaphragm operated valve. The system is automatic. It will go off and on as the
to 2000 pounds per 24 hours (40 kg/hr). REGAL Model 2101
ejector water is turned off and on and will return to the pre-set flow rate.
Chlorinators are modular in design allowing placement of the
vacuum regulator at or near the chlorine storage area, while EJECTOR REQUIREMENTS
locating the flow metering and control panel where convenient Model 2101 Gas Chlorinators are tested to give the best operation in the system
to the operator. The Chlorinators are of the vacuum operated being treated. Generally, the amount of water (GPM) required to operate the
solution-feed type, designed for mounting directly on a chlorine ejector depends upon the chlorine flow rate, the ejector back pressure, and the
manifold header valve. A highly efficient, water operated, water supply pressure which is available. In all cases, the minimum pressure
vacuum-producing ejector assembly also contains a back flow differential and water flow for your installation should be determined prior to
check valve. Chlorine gas flow rate is regulated by a spring installation and start up.
opposed diaphragm regulator which is also the safety shut-off
valve. All components are connected by safe vacuum piping. OPERATION
Should vacuum be interrupted for any reason anywhere in the The vacuum regulator is clamped on the header valve of a chlorine cylinder or ton
system the safety shut-off/inlet valve immediately closes, shutting container manifold. The ejector assembly is either wall mounted or supported by
off the chlorine supply from the pressurized source. rigid pipe. A chlorine flow meter/rate valve panel is located between these two
units and a vacuum line connects the three components.
FEATURES
Water, under pressure is forced through the ejector nozzle which creates a strong
• Fewer parts, simpler design for less down time, easier
vacuum in the ejector body. This pulls gas into the ejector through a special back-
maintenance and lower costs, year after year.
flow check valve and then into the nozzle outlet. The gas mixes with the ejector
• Materials that stand up to ultraviolet degradation and chlorine water and is discharged through the diffuser into the water being treated.
attack…wet or dry.
The ejector vacuum is transmitted back to the chlorinator through the vacuum
• Limited Warranty for the life of the chlorinator on vital line; then through the rate valve and the flow meter and to the back of the
parts…diaphragm and inlet spring against corrosion. diaphragm. With sufficient vacuum, the diaphragm moves backward, opening
• Combined O-ring/diaphragm sealing of the front and back body the spring loaded inlet regulating valve to allow chlorine to enter from the cylinder.
parts helps prevent air leaks into the system and eliminates the
The chlorine passes through the flow rate indicating meter, flow rate adjusting
need for special tightening tools.
valve and to the ejector.
• Inlet safety valve "capsule" allows easy removal with minimal
disassembly for inspection or cleaning with no special tools.
SPECIFICATIONS
The chlorinator shall be a vacuum-operated, solution- REGAL MODEL 2101
feed type, for mounting directly on the auxiliary HIGH CAPACITY GAS CHLORINATOR REMOTE METER
header valve of a wall manifold. It shall be REGAL PANEL ASSEMBLY
Model 2101 manufactured by Chlorinator Incorporated, SERIES 2000
Stuart, Florida and shall have a maximum capacity VACUUM
CHLORINE GAS MANIFOLD (PRESSURE) REGULATOR
of 2000 pounds per 24 hours (40kg/hr). (Optional)

The Model 2101 Gas Chlorinator shall consist of the

VENT LINE
following components: One (1) remote mounted
vacuum regulator, one (1) wall mounted chlorine gas FLEXIBLE
DRIP
CONNECTORS
flow meter panel with rate valve, and one (1) ejector/ LEG
HEATER
check valve assembly. The vacuum regulator shall
mount on the wall manifold auxiliary header valve
by means of a positive yoke type clamp, having an A/C POWER SOURCE
integral tightening screw with slide bar handle. All
metallic bolts shall mate with metallic threaded nut CHLORINE TON
CONTAINERS
or inserts. Plastic mating threads for metallic bolts
shall not be acceptable. REGAL
EJECTOR ASSEMBLY 1" VACUUM PIPING
All vacuum regulating and safety functions, including
a pressure-relief (vent), shall be incorporated in the
BOOSTER PUMP
manifold or ton container mounted vacuum regulator (By Others) BALL VALVE
2" PIPE UNION
unit. The inlet safety shut-off/vacuum regulating (By Others)

valve shall be of capsulated construction, easily SPRAY DIFFUSER

removable as a unit from the outlet side of the yoke

WATER FLOW
for ease of inspection, cleaning or maintenance.
Vacuum shall be created by an ejector assembly
constructed of corrosion resistant plastic. The assembly
shall consist of a fixed throat, orifice type nozzle;
also, a spring loaded back check valve to prevent VACUUM REGULATOR DIMENSIONS
water from entering the gas system.
Model 2101
All materials used in REGAL Gas Chlorinators have Vacuum Regulator Manifold Mounted
been carefully chosen for their excellent corrosion- 1000/2000 PPD (20/40 Kg/Hr)
resistant, ultra-violet resistant properties plus their
ability to withstand stresses far greater than will be 5.0
127
encountered in actual use.

1.88
CONTENTS GUIDE MODEL 2101 48
1 each Model A-2821 Vacuum Regulator with 1 NPT

5/8" Vent and 1" NPT Vacuum Fittings

DIMENSIONS: INCHES
1 each Model A-2551 (1000 PPD) or A-2552 MILLIMETERS
(2000 PPD) Remote Meter Panel with 1" NPT
Vacuum Fittings (For Wall Mounting) 9.0
229 8.0
1 each Model A-2920 (1000 PPD) or A-2922 203
5.81 3.0
(2000 PPD) Ejector Assembly including Nozzle, 148 76
2.88
Back Pressure Check Valve and 1" NPT 73 DIA.
Vacuum Fitting
5.81
25' VT-3, 5/8" Vent and Vacuum Tubing 4.0 148
102
10 each G-201 Lead Cylinder Gaskets
1 each Z-296 Rate Valve Tool
1 each Z-297 Vent Line Bug Screen
Approximate Shipping Weight: 23 lbs

NOTE: No interconnecting vacuum piping

is included.
 ®

MODEL 2107

HIGH CAPACITY
AUTOMATIC
SWITCHOVER
GAS CHLORINATOR

The principal use of the REGAL Gas Chlorinator is to chlorinate ADDITIONAL FEATURES
water, wastewater and industrial process water with gas chlorine. • System Back-up – Each cylinder’s chlorinator has its own vacuum regulating
The simple, efficient design has made REGAL Gas Chlorinators diaphragm and safety/inlet valve insuring that chlorination can be continued if service
the industry standard. Built with heavy duty corrosion resistant should be required on either chlorinator.
parts, REGAL Chlorinators provide safe, long-lasting service. • Corrosion-resistant, Factory-adjusted Detent Mechanism – Detent does not require
any field adjustment assuring that cylinder switchover will occur at the proper time,
The REGAL Model 2107 Automatic Switchover Gas Chlorinators are
and that all available gas in supply cylinder will be used.
totally vacuum-operated chlorination systems which are designed to
• In-Use/Stand-by Indication – Prominent indicator on face quickly tells which is the
automatically switch the chlorine feed from an empty chlorine source
stand-by cylinder and which cylinder is in use.
to a full chlorine source. It is also designed to provide system-backup.
• Pre-tested/Pre-set – The entire REGAL 2107 Gas Chlorinator is tested as a system at
Should a problem develop with either vacuum regulator, chlorination
the factory and no field adjustment or calibration is required to place it into operation.
can be continued. The Chlorinators are of the vacuum operated solution
feed type, designed for mounting directly on a chlorine manifold CAPACITIES
header valve. The switchover chlorinators are self-actuating, eliminating Dual scale metering tubes with maximum capacities of 1000 and 2000 pounds per 24
the need for a separate switchover module. A separate chlorine gas hours of chlorine gas with corresponding metric scales of 20 and 40 kilograms per hour.
flowmeter and rate control valve panel may be located wherever it is The minimum feed rate is 1/20th of the maximum for each metering tube.
most convenient for the operator and connected between the vacuum
regulator junction at the pressure relief (vent) valve, and the ejector, FLOW RATE ADJUSTMENT
by means of safe vacuum piping. The ejector assembly contains a back Manual adjustment is by means of a flow rate control valve located at the top of the
flow check valve. Chlorine gas flow rate is regulated by a spring- flow meter/rate valve panel. Flow rate is then regulated by a special spring-loaded,
opposed diaphragm regulator which is also the automatic safety shut- diaphragm-operated valve in the vacuum regulator. The system is automatic. It will
off valve. Should vacuum be interrupted for any reason anywhere in turn off and on as the ejector water supply is turned off and on and will return to the
the system the safety shut-off/inlet valve immediately closes, shutting preset flow rate.
off the chlorine supply from the pressurized chlorine source. A pressure
relief valve designed to “vent” the system also provides a central EJECTOR REQUIREMENTS
interconnection point for the vacuum piping. Model 2107 Gas Chlorinators are tested to give the best operation in the system
being treated. Generally, the amount of water (GPM) required to operate the ejector
FEATURES depends upon the chlorine flow rate, the ejector back pressure, and the ejector water
• Fewer parts, simpler design for less down time, easier maintenance supply pressure which is available. In all cases, the minimum pressure differential and
and lower costs, year after year. water flow for your installation should be determined prior to installation and start up.
• Materials that stand up to ultraviolet degradation and chlorine OPERATION
attack…wet or dry. The vacuum regulator is clamped on the header valves of chlorine cylinder or ton
• Limited Warranty for the life of the chlorinator on vital parts… container manifolds.The vacuum line is connected from each vacuum regulator unit to
diaphragm and inlet spring against corrosion. the wall mounted, pressure relief (vent) valve, and a single vacuum line connects the
• Combined O-ring/diaphragm sealing of the front and back body outlet of the pressure relief valve to a wall mounted, flow meter/rate valve panel. The
parts helps prevent air leaks into the system and eliminates the need ejector assembly is either wall mounted or supported by rigid pipe, and is connected
for special tightening tools. to the flow meter/rate valve panel with a single vacuum line.
• Inlet safety valve "capsule" allows easy removal with minimal
disassembly for inspection or cleaning with no special tools.
OPERATION (continued)
Water, under pressure is forced through the ejector REGAL MODEL 2107
HIGH CAPACITY AUTOMATIC SWITCHOVER GAS CHLORINATORS
nozzle which creates a strong vacuum in the ejector
SERIES 2000
body. This pulls gas into the ejector through a special VACUUM REGULATOR
CHLORINE GAS MANIFOLD
back-flow check valve and then into the nozzle outlet. (PRESSURE) (Optional)
The gas mixes with the ejector water and is discharged REMOTE METER PANEL ASSEMBLY

through the solution piping into the water being treated. FLEXIBLE
DRIP
LEG
CONNECTORS HEATER
The ejector vacuum is transmitted through the vacuum
A/C POWER
line to the rate valve and the flow meter; then through SOURCE

the connector on the pressure relief (vent) valve and on 1" VACUUM PIPING

to the back of the operating chlorinator diaphragm. PRESSURE

RELIEF VALVE REGAL
With sufficient vacuum, the diaphragm moves backward, (Vent) EJECTOR ASSEMBLY

opening the spring loaded inlet regulating valve to allow

chlorine to enter from the chlorine source. The chlorine DRIP
BOOSTER PUMP
(By Others)
FLEXIBLE 2" PIPE
passes through the chlorinator and the flow rate indicating CONNECTORS
LEG
HEATER
UNION

meter/flow rate adjusting valve to the ejector.

A/C POWER WATER FLOW
When the operating chlorine source starts to run out, SOURCE

the vacuum starts to build up in the system causing the

CHLORINE TON CONTAINERS
diaphragm of the chlorinator on "stand by" to be drawn
back, overcoming a detent mechanism and opening the
safety/inlet valve. This allows chlorine gas to be with-
drawn from the "stand by" chlorine source to satisfy VACUUM REGULATOR DIMENSIONS
the increased system vacuum and the vacuum falls back
to the operating level. The original chlorine supply also Model 2107
continues to feed until it is empty, virtually assuring that Automatic Switchover Vacuum Regulator Manifold Mounted
there will be no interruption of chlorination and that full 1000/2000 PPD (20/40 Kg/Hr)
use will be made of all available chlorine. This also reduces
5.0
the possibility and risk of returning containers with 127
9.0
229 9.69
some remaining gas to the supplier. 5.81 4.63 246
148 117
2.88
SPECIFICATIONS 73 DIA.
The chlorinator system shall be a vacuum-operated, 1.88
48
solution-feed type, and shall automatically switch the 1 NPT
5.81
4.0 148
chlorine supply form an empty chlorine source to a full 102
chlorine source. It shall be REGAL Model 2107 manufactured
by Chlorinators Incorporated, Stuart, Florida, and shall have
a maximum capacity of 2000 pounds per 24 hours (40 kg/hr). DIMENSIONS: INCHES
MILLIMETERS
The Model 2107 Vacuum Operated Automatic Switchover
Gas Chlorinator shall consist of the following components:
Two (2) automatic switchover vacuum regulators, one (1)
wall mounted pressure relief (vent) valve, one (1) wall CONTENTS GUIDE MODEL 2107
mounted chlorine gas flow meter panel with rate valve, 2 each Model A-2817 Switchover Vacuum Regulators with 1" NPT Vacuum Fittings Flowmeter
and one (1) ejector/check valve assembly. The automatic and Rate Valve are on Remote Meter Panel
switchover vacuum regulators shall mount on wall 1 each Model A-2551 (1000 PPD) or A-2552 (2000 PPD) Remote Meter Panel with 1" NPT
manifold auxiliary header valves by means of a positive Vacuum Fittings (For Wall Mounting)
yoke type clamp, having an integral tightening screw
with slide bar handle. All metallic bolts shall mate with 1 each Model A-2920 (1000 PPD) or A-2922 (2000 PPD) Ejector Assembly including Nozzle,
metallic threaded nuts or inserts. Plastic mating threads Back Pressure Check Valve and 1" NPT Vacuum Fitting
for metallic bolts shall not be acceptable. 1 each Model MS-25 1" SLP Tee with 5/8" Vacuum Tube Fitting for Vent Connection
Each chlorinator vacuum regulator shall have its own 1 each Model A-300V4 Pressure Relief (Vent) Valve
diaphragm, safety shut- off/ inlet valve and switchover
detent mechanism, thereby, allowing chlorination to 25' VT-3, 5/8" Vent Tubing
continue should it become necessary to remove either 10 each G-201 Lead Cylinder Gaskets
vacuum regulator for service for cleaning or servicing.
Switchover detent mechanism, shall be made of corrosion 1 each Z-296 Rate Valve Tool
resistant material and shall not require any field adjustment. 1 each Z-297 Vent Line Bug Screen
Vacuum shall be completely created by an ejector Approximate Shipping Weight: 30 lbs
assembly constructed of corrosion resistant plastic. The
assembly shall consist of a fixed throat, orifice type NOTE: No interconnecting vacuum piping is included.
nozzle; also, a spring loaded back check valve to prevent
water from entering the gas system.
All materials used in REGAL Gas Chlorinators have been
carefully chosen for their excellent corrosion-resistant,
ultra-violet resistant properties plus their ability to
withstand stresses far greater than will be encountered
in actual use.

1044 SE Dixie Cutoff Road, Stuart, FL 34994 USA

Tel: 772-288-4854 • Fax: 772-287-3238 • www.regalchlorinators.com • E-mail: [email protected]
Pub. No. 0514-4 © 2014 Chlorinators Inc. Printed in USA