Scribd
Upload
202 views

EXT Switch EXT Switch

Uploaded by

Endang Wahyudi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
202 views

EXT Switch EXT Switch

Uploaded by

Endang Wahyudi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

EXT switch

EXT switch

EXT switch
General information on the EXT switch
Some critical, remote-activated functions are blocked until the driver has enabled re-
mote activation by pressing the EXT switch. This is a general safety function which
is used in a number of bodywork functions. Remote activation enabled is indicated
by the EXT lamp coming on in the instrument cluster.

If EXT is deactivated, all active EXT-dependent functions will be turned off.

316 856
There are two choices of switch that can be used to allow remote activation. An ad-
justable parameter that can be changed with SDP3 (Scania Diagnos & Programmer
3) makes it possible to choose which switch is to be used.
The following options are available: More information on the parameter is found in the following documents:

• Spring-loaded – Spring-loaded switch (standard from factory) • Parameters – Bodywork adaptation (current electrical system, with BCI)
• 2-position – Switch with 2 positions • Adjustable parameters – Other bodywork functions (earlier electrical system,
with BWS)
Function of spring-loaded switch
The spring-loaded switch has the following functions.

• Remote activation is enabled after the switch has been reset once.
• Remote activation is not enabled when the switch is reset once again.
• Remove activation is never enabled immediately after the key in the starter lock
has be turned to drive position without first resetting the switch once.

Function of 2-position switch


In this version remote activation is enabled when the switch is reset from the OFF
position to the ON position. This can only occur when the starter lock is in the drive
position. If the switch is in the ON position when the starter lock is in the drive po-

11:30-01/07 Utgåva 2 en-GB 1 (4)


©
Scania CV AB 2016, Sweden
EXT switch
EXT switch

sition, the switch must first be set to OFF and then set to ON in order to enable remote
activation.

11:30-01/07 Utgåva 2 en-GB 2 (4)


©
Scania CV AB 2016, Sweden
EXT switch
EXT switch

Bodywork functions requiring EXT remote activa-


tion must first have been confirmed by the driver
Present electrical system, with BCI
Information under this heading applies to vehicles manufactured according to the ta-
ble.

Vehicle production period


Production site Chassis serial number
2014-11-17 –
Södertälje 2 105 883 –
Zwolle 5 371 386 –
Angers 9 192 404 –
2015-01-02 –
São Bernardo do Campo 3 872 768 –

The following bodywork functions require remote activation to have first been con-
firmed by the driver via operation of the EXT switch

• Engine speed control


• Remote engine start
• Remote engine shutdown
• Alternating main beam flashing
• Remote activation of visibility and lighting functions

11:30-01/07 Utgåva 2 en-GB 3 (4)


©
Scania CV AB 2016, Sweden
EXT switch
EXT switch

Earlier electrical system, with BWS


Information under this heading applies to vehicles manufactured according to the ta-
ble.

Vehicle production period


Production site Chassis serial number
– 2014-11-17
Södertälje – 2 105 882
Zwolle – 5 371 385
Angers – 9 192 493
– 2015-01-02
São Bernardo do Campo – 3 872 767

The following bodywork functions require remote activation to have first been con-
firmed by the driver via operation of the EXT switch
• Remote hand throttle
• Remote engine speed control
• Remote engine start
• Remote activation of main beam flasher
• Remote horn activation

The following bodywork functions can be selected via SDP3 if the function requires
the EXT switch to be in the ON position for activation:
• Monitored remote engine shutdown
• Remote hazard warning signal activation

11:30-01/07 Utgåva 2 en-GB 4 (4)


©
Scania CV AB 2016, Sweden

You might also like