Effective

Revision TABLE OF CONTENT

Date
Draft

CISTRON DETAILING MANUAL

SR.NO. TABLE OF CONTENT PAGE NO.

1. HOLE SIZE 1

2. GENERAL 2 &3

3. WELD DESIGNATION 4

4. GENERAL WELDING 5&6

5. JOIST INFORMATION 7, 8, 9 & 10

6. ERECTION DRAWING - CHECK LIST 11

7. COLUMN – CHECK LIST 12

8. BEAM & PART DRAWING - CHECK 13

LIST
9. 14
DO’S & DON’T

Prepared By Approved By CISTRON

KSR JN

1
 Effective
Revision HOLE SIZE
Date
Draft

NORMAL HOLE DIMENSIONS (IN) ASD.

REFER: TABLE-1 Vol-I pg 5 - 268

HOLE DIMENSIONS
BOLT
DIA METER STANDARD OVERSIZE SHORT - SLOT (WIDTH LONG - SLOT (WIDTH X
(DIA) (DIA) X LENGTH ) LENGTH)

1/2 9/16 5/8 9/16 x 11/16 9/16 x 1 1/4

5/8 11/16 13/16 11/16 x 7/8 11/16 x 1 9/16
3/4 13/16 15/16 13/16 x 1 13/16 x 1 7/8
7/8 15/16 1 1/16 15/16 x 1 1/8 15/16 x 23/16
1 1 1/16 1 1/4 1 1/16 x 1 5/16 1 1/16 x 2 1/2
> - 1 - 1/8 d + 1/16 d + 5/16 d + 1/16) x (d + 3/8) (d + 1/16) x ( 2.5 x d)

MINIMUM EDGE DISTANCE (IN)

(CENTER OF THE HOLEa TO EDGE OF CONNECTED PART)
AT ROLLED EDGES OF
NORMAL BOLT OR AT SHEARED EDGES PLATES, SHAPES OR BARS
RIVET DIA (IN) GASCUT OR SAW-CUT EDGESb
1/2 7/8 3/4
5/8 1 1/8 7/8
3/4 1 1/4 1
C
7/8 1 1/2 1 1/8
C
1 1 3/4 1 1/4
1 1/8 2 1 1/2
1 1/4 2 1/4 1 5/8
OVER 1 1/4 1 3/4 x DIA 1 1/4 x DIA
a,b,c - CHECK WITH PROJECT INCHARGE

BASE PLATE HOLES

ASD LRFD
ANCHOR BOLT SIZE HOLE SIZE ANCHOR BOLT SIZE HOLE SIZE
3/4 TO 1 IN BOLT SIZE + 5/16 ¾ 1115/16
5/16
1 TO 2 IN BOLT SIZE + 1/2 7/8 1 9/16
OVER 2 IN BOLT SIZE + 1 1 1 13/16

1¼ 2 1/16

LEVELLING PLATE HOLES PLATE WASHER - BOLT SIZE + 1/16

Prepared By Approved By CISTRON

KSR JN

2
 Effective
Revision GENERAL
Date
Draft

Prepared By Approved By CISTRON

KSR JN

3
 Effective
Revision GENERAL
Date
Draft

GENERAL GUIDE

JOISTS ARE BOLTED TO BEAM IF ITS LENGTH IS 40’-0” AND ABOVE.

GALVANIZED ITEMS & ROLLED MEMBERS TO BE DETAILED SEPERATELY

NO BEVEL CUT FOR THE BEAM UPTO ¼” BEVEL

ROOF OPENINGS TO BE DETAILED AS A SINGLE FRAME

NO CLOSURE PLATES FOR HORIZONTAL TUBE MEMBERS AND VERTICAL TUBE

BRACINGS.
BUT PROVIDE CLOSURE PLATES ONLY FOR TUBE COLUMNS.

GUSSET PLATES SHALL BE ROUNDED OF TO 1/2 OR 1/4 (TO THE NEAREST

1/4" - ON THE HIGHER SIDE)

STANDARD FLAT BARS TO BE USED AS FAR AS POSSIBLE (REFER AISC

MANUAL AND CLIENT MANUAL FOR AVAILABLE STANDARDS)

BENT PLATES SHALL BE MAXIMUM 10’-0” IN LENGTH FOR SHOP OR SITE

WELD.
IF TWO 10’-0” LENGTH OF BENT PLATES (EDGE BENT PLT) REST ON BEAM
THEN DON’T WELD PLTS.
JUST BUTT TOGETHER THERE SHOULD BE A NOTE “BUTT TIGHT NO WELD”

Prepared By Approved By CISTRON

KSR JN

4
 Effective
Revision WELD DESIGNATION
Date
Draft

Prepared By Approved By CISTRON

KSR JN

5
 Effective
Revision GENERAL WELDING
Date
Draft

Prepared By Approved By CISTRON

KSR JN

6
 Effective
Revision GENERAL WELDING
Date
Draft

Prepared By Approved By CISTRON

KSR JN

7
 Effective
Revision JOIST INFORMATION
Date
Draft

S.J.I. OPEN WEB STEEL JOIST TOP CHORD WIDTH

TOP CHORD TOP CHORD
JOIST TYPE JOIST TYPE
WIDTH WIDTH

8K1, 10K1, 12K1, 12K3, 12K5 18 LH 06 TO 18 LH 08

14K1, 14K3, 14K4 20 LH 07, 20 LH 08
16K2, 16K3, 16K4, 16K6, 16K7 24 LH 07, 24 LH 07
4" 18K3, 18K4, 18K5 6" 28 LH 07, 28 LH 08
( ± 1") 20K3, 20K4 ( ± 1") 32 LH 07, 32 LH 08
22K4, 22K5 36 LH 07 TO 36 LH 09
24K4, 24K5 40 LH 08, 40 LH 09
44 LH 09

16 K9 18 LH 09
18K6, 18K7 20 LH 09, 20 LH 10
20K5, 20K6 24 LH 09, 24 LH 10, 24 LH 11
4 1/2 " 22K6, 22K7 7" 28 LH 09 TO 28 LH 12
( ± 1") 24K6, 24K7 ( ± 1") 32 LH 09 TO 32 LH 12
26K5, 26K6, 26K7 36 LH 10 TO 36 LH 12
40 LH 10 TO 40 LH 12
44 LH 10 TO 44 LH 12
48 LH 10, 48 LH 11, 48 LH 13

18 K9, 18 K10 28 LH 13
20 K7, 20 K9, 20 K10 32 LH 13 TO 32 LH 15
22 K9, 22 K10, 22K11 8" 36 LH 13 TO 36 LH 15
24 K8, 24 K9, 24 K10, 24 K12 ( ± 1") 40 LH 13 TO 40 LH 15
26 K8, 26 K9, 26 K10, 26 K12 44 LH 13 TO 44 LH 15
5" 28 K6 TO 28 K10, 28 K12 48 LH 14, 48 LH 15
( ± 1") 30 K7 TO 30 K12
18 LH 02 TO 18 LH 05
20 LH 02 TO 20 LH 06 40 LH 16
9"
24 LH 03 TO 24 LH 06 44 LH 16, 44 LH 17
( ± 1")
28 LH 05, 28 LH 06 48 LH 16, 48 LH 17
32 LH 06
FOR JOIST BEARING DEPTH AND GAGE REFER ATTACHMENT – 1
STABILIZER PLATE REFER ATTACHMENT – 2
MINIMUM BEARING
MIN. EXT. OVER WALL
JOIST TYPE ON STEEL PLATE WIDTH (┴ TO
SUPPORT
SUPPORT JOISTS)
K – SERIES 4" 2 1/2 " 6"
VS - SERIES 4" 2 1/2 " N.A.
LH, DLH 6" 4" 9"

JOIST GIRDERS 6" 4" 9"

Prepared By Approved By CISTRON

KSR JN

8
 Effective
Revision JOIST INFORMATION
Date
Draft

Prepared By Approved By CISTRON

KSR JN

9
 Effective
Revision JOIST INFORMATION
Date
Draft

N.J BOUROS JOIST STANDARDS

JOIST TYPE SEAT DEPTH HOLE SIZE HOLE GAGE

JG 7 ½” 13/16 X 1 ¼ SLOTS 5”

LH, DLH 5” 13/16 X 1 ¼ SLOTS 4”

K, KCS 2½ 9/16 X 2 SLOTS 3½

VS 2½ NA NA
COMMON JOIST STANDARDS

JG 7 ½” 7/8 X 1 ¼ SLOTS 5”

LH, DLH 5” 7/8 X 1 ¼ SLOTS 4”

K, KCS 2½ 5/8 X 1 SLOTS 3½

HONCOCK JOIST STANDARDS

JG 7 ½” 13/16 X 1 ½ SLOTS 4”

LH, DLH 5” 13/16 X 1 ½ SLOTS 3 ½”

K, KCS 2½ 5/6 X 1 ¼ SLOTS 3 ½”

VULCROFT JOIST STANDARDS

JG 7 ½” 13/16 X 2 SLOTS 5”

LH, DLH 5” 13/16 X 2 SLOTS 4”

K, KCS 2½ 9/16 X 2 SLOTS 3¼

Prepared By Approved By CISTRON

KSR JN

10
 Effective
Revision JOIST INFORMATION
Date
Draft

Prepared By Approved By CISTRON

KSR JN

11
 Effective ERECTION DWG – CHECK
Revision
Date LIST
Draft

ERECTION DWG - CHECK LIST

MARK
Sl.
No.
PROJECT : DRG NO:


1. TITLE BLOCK FOR CUSTOMER, CLIENT, PROJECT & PLAN DETAILS

2. NORTH MARK
3. GRIDS AND DIMENSIONS WITH DESIGN INPUT
4. COLUMN ORIENTATION AND ALL MEMBER SIZES WITH DESIGN INPUT
5. ANY COLUMN AWAY FROM GRIDS MARK DIMENSIONS IN "X" AND "Y" DIR.
6. ERECION MARKS GIVEN PROPER LEFT SIDE OF BEAM

7. FLOOR OPENINGS AND ENSURE FOR DECK CLOSING (OPENING SYMBOL)

8. MARK EDGE OF SLAB/DECK AND CHECK CLOSURE PLATE / ANGLE

THE FLOOR BEAMS ARE IN SAME ELEVATION, ELEVATION CAN MARK COMMON IN
9.
THE TITLE, CHANGING ELEVATION SHOULD MARK IN PLAN
10. BRACINGS - VERTICAL BRACINGS TO BE SHOWN IN ELEVATION
11. FOR ANGLES AND CHANNELS MARK ORIENTATION
COLUMN ENDS WITH FLOOR BEAM "BELOW" TO BE MARKED IN COLUMN E-MARK &
12.
COLUMN STARTS FROM THE FLOOR LEVEL "ABOVE" TO BE MARKED

13.
MARK SLOPE SYMBOL IN SLOPING AREAS
14. MARK "CAMBER", IN BEAMS (REFER PROJECT REQUIREMENT)

15. MOMENT CONNECTIONS MARK SYMBOL WHERE REQUIRED

16. ALL FIELD WELDING DETAILS TO BE SHOWN (TAKE SECTIONS)
17. KEYPLAN TO BE DRAWN & DETAILING AREA SHOULD MARKED
18. MATCH LI NE / SEQ LINE MARKED CORRECTLY.
19. ALL EMBEDS / ATTACHMENTS MARKED IN PLAN / SECTION
20 GENERAL NOTES FOR SECTION DRG NOS AND CONNECTION DRGS,

ERECTOR NOTE - PROJECT NON-STD BOLTS AND REMOVAL OF ERECTION AIDS TO

21
BE MARKED

Prepared By Approved By CISTRON

KSR JN

12
 Effective
Revision COLUMN - CHECK LIST
Date
Draft

COLUMN - CHECK LIST

MARK
Sl.
No.
PROJECT : DRG NO:


1. COLUMN DIRECTION WITH PLAN NORTH

2. BASE PLATE ELEVATION & WELDING, BASE PLATE HOLES

3. WITH ANCHOR BOLT DETAILS FOR BOLT PITCH & DIMENSIONS
4. COLUMN ELEVATION
5. CUTTING LENGTH & DIMENSION
6. PART FIXING DIMENSION

7. HOLE FIXING DIMENSION

8. WELDING / BOLTING DTAILS FOR ALL PARTS

9. PROPER / REQD SECTIONS TAKEN

10. PART QUANTITY

11. ' NO PAINT' REQUIREMENTS

12. 'OSHA' REQUIREEMNTS

13. LIFTING HOLE REQUIREMENTS

14. FOR EDGE PREPERATION (BEVEL TO GIVE)

15. B.O.M & MATCH QUANTITY & LENGTH

16. SHOP BOLT QTY

17. PRESENTATION

Prepared By Approved By CISTRON

KSR JN

13
 Effective
Revision BEAM – CHECK LIST
Date
Draft

BEAM - CHECK LIST

MARK
Sl.
No.
PROJECT : DRG NO:


1. ORIENTATION MARK

2. CUTTING LENGTH & ASSEMBLY LENGTH

3. PART FIXING DIMENSION
4. HOLE FIXING DIMENSION
5. WELDING / BOLTING DETAILS FOR ALL PARTS
6. PROPER / REQD SECTIONS TAKEN

7. PART QUANTITY

8. ' NO PAINT' FINISH REQUIREMENTS

9. FOR EDGE PREPERATION (BEVEL TO GIVE) (REMARKS IF ANY)

10. B.O.M & MATCH QUANTITY & LENGTH

11. SHOP & FIELD BOLT QTY

12. PRESENTATION, PROPER SCALE

13. CHAMBER

14. SLOT SIZE & DIRECTION

15. FLANGE CUT & CHIP NOTES

16. REMARKS BENT PLATE, PLAIN MATERIAL BEVEL CUT

17. CONNECTING SIDE MARK
18. NO CROSSING DIMENSION

CHECK LIST - PART DRAWING

MARK
Sl.
No.
PROJECT : DRG NO:


1. CUTTING DIMENSIONS

2. HOLE LOCKING DIMENSOINS

3. HOLE DIAMETER OTHER THAN U.N.O. MARKED IN TITLE BLOCK
4. SLOT DIMENSION AND DIRECTION SYMBOL
5. PART MARK
6. EDGE PREPERATION

Prepared By Approved By CISTRON

KSR JN

14
 Effective
Revision DO’S & DONT
Date
Draft

Prepared By Approved By CISTRON

KSR JN

15