Installation and Configuration manual

Crew Voice and Video Recording

System (CVVRS)

Spec no: RDSO/2015/EL/SPEC/0118

REV-0 issued on 17.09.2015

Prepared by:
Kaamney Electronics Pvt. Ltd.
Add: C-8 Sector 88 Noida UP-201305

Email: [email protected]
 Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Installation Procedure for CVVRS in Electric Loco

1. Place the item No (a) (Base plate) of indoor camera (Ref Drg) enclosure at proper location as marked in
drawing at four places inside the driver cabin of loco.

2. Weld the edges of the said base plate to the body of loco at four locations.

3. Welding to be proper and without blow holes.

4. Remove the extra weld sludge by filing/ grinding.

5. Provide a coating of paint on the welded portion to prevent from rusting.

6. Mount the indoor camera’s (Item No 1) at all the four locations by M4 screws (Item 10 a).

7. Place the item no (c) (base plate) of outdoor camera enclosure at the location (near flash light) as marked in
the drawing. (One number Only)

8. Weld the edges of the said base plate to the body of loco.

9. Welding to be proper and without blow holes.

10. Remove extra weld & sludge by filing/ grinding.

11. Provide a coating of paint on the welded portion to prevent from rusting = mount the outdoor camera (Item
No 2) with M4 screws (item 10a).

12. Assembly of DC-DC convertor and NVR to be done on NVR mounting plate (Item No 5) with M4x12 screw, nut, plain
washer & Spring washer (Ref assembly photo)

13. Mounting of NVR Mtg plate assembly to be done at proper location by drilling four holes on the body matching to
NVR mtg plate (Item 5). Do Mounting & tapping on them use M6x30 Screw (item 10) to tight on it with loco body.

14. Mounting GPS antenna inside flasher light box space. Do wiring using CAT 6 cable (item 8). Route the wire through
PVC conduit of dia 25mm and 12mm as reflected in schematic diagram. Also route GPS antenna wire upto NVR
Mounting plate assembly.

15. Connect Connector (Item 9) M12- D code at 12 terminals (Each camera and on NVR) with proper sequence of wires.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 1 of 32
 Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

16. Use 1.5 Sqmm (Twin wire) for supply of 110V DC form MCB of the panel in the loco to the DC-DC convertor at its
input terminal. Loose connection not allowed.

17. Use cable tie as per requirement at various places to tie the flexible conduit.

18. The connectors of NVR, indoor camera & outdoor cameras to be connected to their matching connectors.

19. The protection covers (b&d) respectively for indoor camera & outdoor cameras to be fixed with M4x8 (Item 10)
screws only after doing testing and adjustment of lenses for proper view.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 2 of 32
 Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

CVVRS SCHEMETIC DIAGRAM

2 4

Indoor * * Indoor
Camera Camera

1 6

Outdoor Outdoor
Camera * * Camera

3 5
Indoor Indoor
* *
Camera Camera

110 VDC from SB2 Panel

through DC MCB (DP)
+ve (red) -ve(black) Cat 6 Cable

*Here use 12mm flexible conduit

Δ Here use 25mm flexible conduit

NVR DC-DC
(110-24)

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 3 of 32
 Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

CVVRS Wiring Layout (Electric Loco Type WAP-7)

C3 C4

SB2 Panel Cat 6 Cable

NVR

C1 C2 C5 C6

PLAN VIEW

C1 C6

====== ======
NVR Assly. ====== ======
=

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 4 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

BOM

S.No. Item Cat No Qty. Reference

1. Inside Camera(C2,C3,C4,C5) DS-2CD6510D-I 4
2. Outside Camera(C1,C6) DS-2XM6522WD-I 2
3. Indoor Camera Enclosure Figure 1 4 Figure 1
4. Outdoor camera Enclosure Figure 2 2 Figure 2
5. NVR Mtg Plate Figure 3 1 Figure 3
6. NVR DSM7508HNI/GW/WI 1
7. Power Supply 24V DC 100W KB 110-24VDC 100W 1
8. Cat 6 Cable D-Link 90-100 Mtr
9. Connector M12 D-Code 12
10. Hardware:-
a)M4x12 Cheese head Screw M4x12 Cheese head Screw 24
b) M4x8 Cheese head Screw M4x8 Cheese head Screw 36
c) M6x30 Hex head Screw M6x30 Hex head Screw 4
d) Plain washer M4 Plain washer M4 24+36
e) Spring washer M4 Spring washer M4 24+36
f) Plain washer M6 Plain washer M6 4
g) Spring washer M6 Spring washer M6 4

Additional material for wiring-

S.No Item Specification Qty.

1. Conduit Flexible 25mm Ø As per requirement.
2.. Conduit Flexible 12mm Ø As per requirement.
3. PVC Wire 1.5 Sqmm As per requirement.
4. MCB (DP) 2A 110V DC As per requirement.
5. Cable Tie 3-4 Inch As per requirement.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 5 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Protection cover, base plate, NVR assembly Images

Fig 1
(B: Indoor camera protection cover) (A: Indoor camera base plate) (Indoor camera with base plate)

Fig 2
(D: Outdoor camera protection cover) (C: base plate for outer camera) (Outdoor camera with base plate)

Fig 3
(NVR mounting plate) (NVR assembly)

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 6 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Installation pictures in Electric Loco Type WAP-7

a) First the camera base is mounted.
b) Then the camera is mounted on the base.
c) Once the camera is installed, tested and all view and lens adjustments are done, then the camera
cover is mounted for protection.

1) Indoor Saloon camera positioning right side (inside loco cab):

2) Indoor Saloon camera left side (inside cab):

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 7 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

3) Outdoor Camera positioning and mounting (on either end of loco)

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 8 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Images taken during initial trials at DMW to finalize the design and placement (for Ref only)

A) Indoor camera

B) Outdoor camera

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 9 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

3) NVR assembly unit (with DC-DC Converter and NVR mounting)

NVR Base Plate NVR unit assembly

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 10 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

4) Network Video Recorder (NVR)

a) The six cameras are to be connected from POE1 – POE8 (use any 6 ports as shown in below figure)
b) The output of the DC-DC converter (24VDC) to be connected to “Power” port on the rear panel of
the NVR device, shown in the below image.

NVR Rear Panel

5) M12 D-coded connector configuration and colour coding

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 11 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

6) Camera view:

Note: Please note that the camera and NVR mounting placement is for reference only.
The location may vary depending upon the type of loco and space availability.

************************ THE END***********************

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 12 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Installation and Configuration manual for CVVRS in Electric Loco Type WAP-7

1) NVR Physical Interfaces:

Front Panel on NVR

Rear Panel of NVR

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 13 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

2) Peripheral Connection Interfaces on NVR:

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 14 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

3) Hard disk Installation process in NVR

Perform the following steps to install the HDD on the mobile NVR.

Step 1:
Prepare the tools and components for installation: one 2.5-inch SATA HDDs, antistatic gloves, key to
hard disk lock, cross screwdriver, conventional screws and sunk screws.

Step 2:
Insert the key and turn in counter clockwise to open the hard disk lock, unfasten the screws counter
clockwise and pull out the hard disk box.

Note:
The hard disk lock is locked when the keyhole stands upward and is open when the keyhole stands
leftward.

Step 3:
Loosen and remove the two set screws marked in the figure with the screwdriver, and then take the
hard disk apart.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 15 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Step 4:

The assembly parts of the hard disk box are shown in the figure.

Step 5:
Place the HDD into the hard disk box, with the PCB facing downward.

Step 6:
After the HDD is fully placed into the bracket, reverse the hard disk box and flat the HDD. There are
two disk sockets in the bracket and tightly insert the first HDD into the one at the bottom.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 16 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Step 7:
Tighten the four screws marked in the figure to fix the HDD.
Note:
For some certain HDDs, only the two upside screws are available. Tighten the two screws and go to
the next step.

Step 8:
Tighten the two set screws on the left and right sides of the hard disk box, shown in the figure, to fix
the inserted HDD.

Step 9:
Align the two sharp edges of the hard disk box marked in the figure, and assemble the whole hard
disk box.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 17 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Step 10:
Tighten the two set screws of the hard disk box, as shown in the figure.

Step 11:
Insert the hard disk box back to the mobile NVR, and then tighten the screws clockwise.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 18 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

4) USB mouse operations

A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this device. To use a
USB mouse:
1. Plug USB mouse into one of the USB interfaces on the front panel of the device.

2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the
possible reason may be that the two devices are not compatible

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 19 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Chapter 2 Basic Operations

2.1 Setting Admin Password
Purpose:
For the first-time access, you need to activate the device by setting an admin password. No
operation is allowed before activation.
Steps:
1. Input the same password in the text field of Create New Password and Confirm New Password.

2. Click OK to save the password and activate the device.

2.2 Main Page

Using USB mouse, Right click on the screen, and then select the Menu item on the right-click menu
to enter the main page.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 20 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Figure 2. 2 Main Page

Click the sub-menu icon on the screen to enter the interface of the sub-menu.

Right click on the screen to go to the previous page or exit from the main page.

2.3 Local Network Settings

Steps:
1. Enter the Local Network Settings interface.
Menu>Basic Settings>Network.

Below screen will appear

2. Select Interface as “Rear Interface”

Fill in the below values:

IP address: 192.168.1.40
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1

As shown below:

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 21 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Click on Apply and OK.

The device might ask for reboot, for the changes to take effect.
If so, click Yes to allow system to reboot.

2.4 IPC Settings

Purpose:
IP camera can be added to the mobile NVR, and thus you can get the live view or record the video of
the connected IP cameras. You can also set the parameters of the connected IP camera or delete it
according to the actual needs.

Click the IPC icon on the Other Settings interface to enter the IP Camera Settings interface.

2.4.1 Activating IP Cameras

Purpose:
Before adding the cameras, make sure the IP cameras to be added are in active status.
Steps:
1. Enter IPC Settings interface.
Menu > Other Settings > IPC Settings

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 22 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

2. Click to select an Inactivated IP camera.

3. Activate the selected IP camera.
Option 1: Quick Activation
Click the Quick Activation button. Thus the IP camera password is set as the same with the Mobile
NVR password.

4. Select the activated IP camera and go to “Edit” option.

Assign the IP in the same range as that of NVR, i.e. 192.168.1.xxx
xxx denotes any number from 0-255, other than the one assigned to NVR.
(For eg in this case, xxx can be any number other than 40)

So, we can assign the below IP address to 6 different cameras, like:

192.168.1.42
192.168.1.43
192.168.1.44
192.168.1.45
192.168.1.46
192.168.1.47

Assign IP address to all the 6 cameras as shown above.

2.4.2 Adding IP Cameras

Adding IP Camera Automatically
Purpose:
The online IP cameras in the same network segment with the system will be displayed on a list.
Steps:
1. Click to select the IP camera on the list.
2. Click the QuickAdd button, and the selected IP camera will be added automatically.

Make sure the IP camera password is the same with mobile NVR, or adding IP camera will fail.
The icon indicates the IP camera is offline;
The icon indicates the connected IP camera works properly.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 23 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

2.4.4 Deleting IP Cameras

If required, use the below process for deleting any IP camera.
1. Select the IP camera on the list, and click Delete button.
2. Confirm the pop-up dialog box, and the selected IP camera is deleted from the system.

2.4.5 If all 6 cameras are connected, IPC settings and live view will be like this:

The icon indicates the connected IP camera works properly.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 24 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

The small red icon on top right of each camera display, indicates that the recording is working
fine.

2.5 Display Settings

Purpose:
You can set the system time, select the CVBS output standard, enable the password, configure the
DST settings, etc.
Steps:
1. Enter the Display Settings interface.
Menu>Other Settings>Display

2. Select the CVBS output standard as PAL.

3. Set the system time.
4. Select the VGA resolution from the drop-down list.

The VGA resolution is only configurable when the Mobile NVR is connected to a VGA monitor. And
you can set it as
1024*768/60Hz, 1280*720/60Hz, 1280*1024/60Hz or 1920*1080/60Hz.

5. Check the checkbox of Enable Password enable the password authentication before operations.

2.6 Camera Settings

Purpose:
You can configure the camera name, OSD (On Screen Display) settings, etc.

The settings of OSD, standing for On Screen Display, include the display of camera name, date and
week and the corresponding position information.
Steps:
1. Enter the Camera Settings interface.
Menu>Other Settings>Camera

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 25 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

2. Select the camera from the drop-down list.

3. Input the camera name as desired in the text field.
4. Check the checkboxes to display the camera name, date or week on the live view interface of
selected camera.
5. Select the date format and time format according to the actual needs.
7. Click the Set button of More Setting, and you can configure the video parameters:

Image Settings
Perform the following steps to adjust the video parameters, including Brightness, Contrast,
Saturation and Hue.
1) Click the Set button of Image Settings to enter the Image Settings interface.
2) Select the parameter item, press Enter key on the remote control, and use the Direction keys to
adjust the
value of the selected item.
3) You can click Default to restore the default video parameters.
4) Click OK to save the new settings.

2.7 Preview Settings

Purpose:
You can configure the dwell time of live view window, set the camera order, enable/disable the
audio preview, etc.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 26 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Steps:
1. Enter the Preview Settings interface.
Menu>Other Settings>Preview

2. Select the video output from the drop-down list according to the actual needs.
3. Select the preview mode, dwell time for live view, and then enable/disable the audio output.
Preview Mode: select the window division mode for live view.
Dwell Time: the switch interval of the live view screen. The screen will be switched to the next one
after the
selected dwell time.
Enable Audio Output: Enables/disables audio output for the selected video output.
4. Click the Set button to set the camera order.
Perform the following steps to set the camera order for display:

1) Use the Direction keys on the remote control to select the icon on the screen, and press
the Enter
key to go to the previous / next display window.
2) Select the display window, and press Enter key on the remote control to enter the edit mode.
3) Press Direction keys on the remote control to select the camera for display.

The character “X” means no camera will be displayed on the selected window.
4) Press Enter key on the remote control to confirm the settings.
5) Click OK to save the new settings and exit.

For mouse operations, you can click the icon to select the display window, and click the
icon to set the
camera for display.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 27 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

5. Click the Apply button to save the new settings and click OK to exit.

Chapter 4 Record Settings

4.1 Configuring Encoding Parameters
4.1.1 Initializing the HDD

Before you start:

Install at least one HDD on the mobile NVR for video data storage.
Steps:
1. Enter the HDD Management interface.
Menu>HDD

2. Select the hard disk from the drop-down list. You can view the status, free space and capacity of
the HDD.
3. Set the overwrite mode to Yes or No to enable or disable the disk overwriting function for the
selected HDD.
Note:

 If the hard disk is installed correctly and formatted, the status is displayed as normal or
sleeping.
 The disk overwriting function is enabled by default. If the disk overwriting function is
disabled, the recording will stop when the hard disk is full.

4.1.2 Configuring Record Settings

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 28 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Purpose:
You can configure the transmission stream type, the resolution, frame rate, etc.
Steps:
1. Enter the Record Settings interface.
Menu>Basic Settings>Record

2. Select the camera from the drop-down list.

3. Configure the following settings:
Encoding Parameters
Main Stream (Normal): used for schedule recording;
Main Stream (Event): used for event recording;
Sub Stream: used for network transmission.

Note:

When Main Stream (Event) is selected as the encoding parameters, the settings of stream type,
resolution,
bitrate type, video quality, frame rate and max. bitrate are the same with that of Main Stream
(Normal) and
cannot be configured.

Stream Type
Video and Video & Audio are selectable.
Resolution
Select the resolution for the selected camera and stream type. 1080P (1920*1080), XVGA
(1280*960), and
HD720P (1280*720) are selectable.
Bitrate Type
Variable and Constant are selectable.
The video quality is configurable when you select Variable to the bitrate type; and the video quality
is set as
Medium by default and cannot be edited when you select Constant to the bitrate type.
Video Quality
If you select Variable to the bitrate type, you can set the video quality as Highest, Higher, Medium,
Low, Lower
and Lowest.
Frame Rate

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 29 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

Frame rate refers to the frequency of the image frame after compression. With other parameters
constant, reduce
the video frame rate, and you can lower the maximum bitrate to some extent.
Max. Bitrate(Kbps)
Select the fixed value provided by the system or customize the maximum bitrate as desired.

4.4 Searching Record Files

Purpose:
You can search and play back the record files stored on the device.
Steps:
1. Enter the Video Search interface.
Menu>Video Search

2. Select the camera and video type from the drop-down list, and then specify the start time and end
time for search.
3. Click the Play button, and you can play back the searched record files directly.
A playback toolbar appears at the bottom of the playback interface.
Click-and-drag the slider with the mouse, and you can adjust the playback process as desired.
Click the icon and you can enable / disable to audio of the record files.
Click the icon and you can start / stop clipping the record files and save the video clips when
exiting from
the playback interface.

4. Click the Search button, and the record files will be displayed on a list.
Select the record file, click the Play button, and you can play back the selected record file.
Select the record files, click the Export button, and you can export the record files for backup.

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 30 of 32
Item: Crew Voice and Video Recording System (CVVRS) Ref doc: KE/2019-20/CVVRS/QC/001
Spec no: RDSO/2015/EL/SPEC/0118 REV-0 issued on 17.09.2015 Date: 20/12/2019

7.2 Configuring Satellite Positioning

Purpose:
The built-in GNSS module supports both GPS (Global Positioning System) and BDS (BeiDou
Navigation Satellite System,
reserved), contributing to the device positioning and speed limit alarm.
Steps:
1. Enter the Satellite Positioning Settings interface.
Menu>Basic Settings>Position

2. Select the mode of the Position Module.

Built-in: Obtain data from the satellite positioning module built in the mobile NVR. (USE THIS
OPTION)
3. Check the checkbox of Satellite Time Adjusting and then select the time zone in which the device
locates.
4. Select the speed unit and input the speed limit value.
6. Click the Set button of Display Channel, and select the connected IP cameras. Then the device
positioning information
will be displayed on the selected channels.
7. Click OK to save the new settings and exit.
You can view the device positioning status on the Positioning Status interface
(Menu>Status>Position).

***************THE END**********************

Kaamney Electronics Pvt. Ltd.

C-8, Sector 88, Noida, UP-201305

Page 31 of 32