H.264/H.

265 (HEVC)
IPTV ENCODER & STREAMER
SERIES

OVERVIEW AND QUICK START

USER MANUAL
IRENIS Encoder & Streamers | User Manual

APPLİCATİON EXAMPLE:

Author: Rri, August 2017, Version: V1.3 -2-

IRENIS Encoder & Streamers | User Manual

Thank you for choosing our products. Please contact us if you have any question – see last page
This manual applies to the following models: (depending on changes in model types and ranges
this is a subject to change w/o further notice)

H.264 Video Encoder Series

One channel HDMI H.264 encoder

• Support H.264Baseline Profile / H.264Main

Profile / H.264High Profile
HDE-264
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS

One channel VGA H.264 encoder

• Support H.264Baseline Profile / H.264Main

Profile / H.264High Profile
VGE-264
• Support up to 720P, 1080P HD video input
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF

One channel SDI H.264 encoder ,with one

channel SDI looping out

• Support H.264Baseline Profile / H.264Main

SDE-264
Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS

Mini HDMI+CVBS H.264 video encoder

• Support H.264Baseline Profile / H.264Main

Profile / H.264High Profile
ADE-264 • Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF

Author: Rri, August 2017, Version: V1.3 -3-

IRENIS Encoder & Streamers | User Manual

H.264 HDMI+VGA decoder

• H.264Baseline/High/Main Profile decoding

• MJPEG/JPEG Baseline decoding
VHE-264 • Audio decoding MPEG1 Audio Layer 2
• Support Network interface full-duplex mode 100M
• 1 channel HDMI/vga/audio output
• Support up to 1080P/60hz HD video output
• Support HTTP, UTP, RTSP protocol

16 channels HDMI H.264 encoder in rack

• Support H.264Baseline Profile / H.264Main

Profile / H.264High Profile
HDE-16264 • Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF

16 channels HDMI + CVBS H.264 encoder

in rack

• Support H.264Baseline Profile / H.264Main

ADE-16264 Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF

4 channels HDMI H.264 video encoder

• Support H.264Baseline Profile / H.264Main

Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
HDE-4264 • Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
• Dimensions : 430mm x 250mm x 45mm
(LxWxH)
• Net Weight: 3KG

Author: Rri, August 2017, Version: V1.3 -4-

IRENIS Encoder & Streamers | User Manual

4 channels HDMI + CVBS H.264 video

encoder

• Support H.264Baseline Profile / H.264Main

Profile / H.264High Profile
• Support up to 720P, 1080P HD video input
ADE-4264 • Support HDCP protocol and HD blue-ray
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
• Dimensions : 430mm x 250mm x 45mm
(LxWxH)
• Net Weight: 3KG

4 channels SDI H.264 video encoder

• Support H.264Baseline Profile / H.264Main

Profile / H.264High Profile
SDE-4264
• Support up to 720P, 1080P HD video input
• Support 1080P@60fps
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF
• Dimensions : 430mm x 250mm x 45mm
(LxWxH)
• Net Weight: 3KG

Author: Rri, August 2017, Version: V1.3 -5-

IRENIS Encoder & Streamers | User Manual

19” 1 RU Encoder Series

H.264 Video Encoder into 1 RU case with

HDMI input+BNC input+Independent Audio
ADE-1264
• Support 1080P@60fps
• Single channel IP output
• Support HTTP,RTMP,RTSP,UDP,ONVIF
protocol
• Support unicast and multicast

H.265 Video Encoder into 1 RU case with

HDMI input

HDE-1265 • Support H.264BP/MP/HP

• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps

H.265 Video Encoder into 1 RU case with

SDI input

• Support H.264BP/MP/HP
SDE-1265
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps

H.264 Video Encoder into 1 RU case with

4CH HDMI input
HDE-4264
• Support 1080P@60fps
• 4 channel IP output
• Support HTTP,RTMP,RTSP,UDP,ONVIF
protocol
• Support unicast and multicast

Author: Rri, August 2017, Version: V1.3 -6-

IRENIS Encoder & Streamers | User Manual

H.265 (HEVC) Video Encoder Series

One channel H.265 HDMI video encoder

• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
HDE-265 • Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps

One channel H.265 SDI video encoder

• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
SDE-265 • Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps

One channel H.265 VGA video encoder

• Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
VDE-265 • Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
H.265 Video Encoder into 1 RU case with
HDMI input
• Support H.264BP/MP/HP
HDE- • Support H.265 Main Profile
1265 • Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
H.265 Video Encoder into 1 RU case with SDI
input
• Support H.264BP/MP/HP
SDE- • Support H.265 Main Profile
1265 • Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps

Author: Rri, August 2017, Version: V1.3 -7-

IRENIS Encoder & Streamers | User Manual

H.264/H.265 Wireless Video Encoder Series

1 channel SDI input encoder

• Connect the internet by Wifi or ethernet port

SWE-264 • 1 Channel SDI input;
• 1 channel SDI loop output.
• Same specification as SDE-264

1 channel H.265 SDI video encoder with 1

channel SDI loop out with wifi

• Connect the internet by Wifi or ethernet port

SWE-265 • Support H.264BP/MP/HP
• Support H.265 Main Profile
• Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS
• Support 1080p@60fps
One channel HDMI H.264 encoder with wifi

• Support H.264Baseline Profile /H.264Main

Profile / H.264High Profile
HWE-264 • Support up to 720P, 1080P HD video input
• Support HDCP protocol and HD blue-ray
• Support protocol HTTP, UTP, RTSP, RTMP,
ONVIF, HLS

Almost all models with ONVIF support can be used with following protocols:
“ONVIF S, “ONVIF C” or “ONVIF G”

Statement:

Text and pictures herein are subject to changes w/o notifications.

The user manual will be updated in real time without special notice.

This user manual is provided only as a reference guide for technicians as examples.

Author: Rri, August 2017, Version: V1.3 -8-

IRENIS Encoder & Streamers | User Manual

Default Values

The factory default administrator account: admin

The factory-default user password: admin
The factory default IP address: 192.168.0.31 or 192.168.1.168
Please change these account settings according to your local policy and network. -> Do not forget to
safe and backup the configuration.

1 PRODUCT OVERVIEW

The H.264/H.265 Encoder is a hardware device used for high-definition video signal (up to 1080p HD
resolution) encoding and network transmission, using the latest and high-efficient HD digital video
compression technology H.264/H.265, with the characteristics of reliable, high-definition, low bitrate and
low latency. Connect the HDMI/SDI/VGA high-definition video signal to start the encoding process, after
the compression processing by the DSP chip, the output of the standard TS network stream can be
started.

The launch of these devices fills the gap in the industry, which is a direct replacement for the traditional
capture card for software coding method, using hard-coded chipsets, the system is more stable, and the
picture quality is more perfect. They can be used in a wide variety of demands for high-definition video
and high-resolution / high frame rate re-assembling for IP based network transmission. Its powerful
scalability makes it more easier to respond to the needs of different industries and can be used as live
video encoder. Industrial controlled, precision design, small size, easy installation, the power is less
than 5W, which is energy-saving and more stable.

2 PRODUCT FEATURES

• High-performance hardware encoding

• h.265 video coding efficiency (depending on Model, downward compatible to h.264)
• h.264 BP/MP/HP
• AAC / G.711 Advanced Audio Coding format quality
• CBR / VBR rate: 16Kbps ~ 12Mbps
• 1000Mbit/s network interface using full duplex mode
• A mainstream and second stream can be sent to different IP-connections
• Supports up to 720P, 1080P @ 60HZ HD video input
• Support image parameter settings
• HDCP protocol and Blu-ray
• HTTP, UTP, RTSP, RTMP, RTP, ONVIF protocol
• The mainstream and second stream can be used with different network protocol for their
transmissions
• WEB interface with 2 Languages: English and optional Chinese for Asian customers
• Support remote management in WAN (WEB)
• Support customized settings for the resolution
• Support one step to restore the factory configuration
• Support SDK / individual development

Author: Rri, August 2017, Version: V1.3 -9-

IRENIS Encoder & Streamers | User Manual

3 APPLICATIONS

• IPTV
• Digital Signage
• Video Conference
• Hotel IPTV System
• Live Broadcast Feeds
• Campus IPTV System
• IP Recording System
• Medical video broadcast and recording system
• Live video education system
• IP Video Recording (DVR/NVR)
• 4G mobile broadcast HD front capturing

4 INTERFACE DESCRIPTION

4.1 The interfaces of H.264HDMI encoder and WIFI encoder are almost similar：

4.2 The interfaces of H.264SDI encoder and WIFI encoder are similar：

4.3 H.264VGA Encoder：

Author: Rri, August 2017, Version: V1.3 - 10

-
IRENIS Encoder & Streamers | User Manual

4.4 HDMI CVBS HD Encoder：

4.5 The interfaces of H.265 HDMI encoder and WIFI encoder are similar：

4.6 The interfaces of H.265 SDI encoder and WIFI encoder are similar：

4.7 The interfaces of H.264VGA encoder and WIFI encoder are similar：

From Left to Right:

A. Power input----- 12V/DC（12V/1A，5V/2A optional）

B. RST=RESET button ------ useful to reset the device to factory defaults . After power on ,
press it for about 15 seconds to reset the device to default IP 192.168.0.31
(192.168.1.168 – depending on Model)
C. AUDIO/Video input------ Input HD HDMI, SDI, VGA, Audio signals
D. 1000BaseT Ethernet port RJ45
E. Status Indicator：
1) Will flash while pressing the RESET button. Reset is successful when the light turns
off . Slow Flashing show: Video input , image capturing and compression is working..
2) If the indicator light keeps on, the Video source acquisition and compression has
some problem like resolution/format our out of Input specification. Sync failed...
3) If the indicator LED flashes slowly but the output stream is not working , there might
be a problem with the streaming server part.

Author: Rri, August 2017, Version: V1.3 - 11

-
IRENIS Encoder & Streamers | User Manual

5 WEB SERVER SETTINGS

Step 1: Reset & initialization

Connect the power supply to turn on the encoder and use a pin to press RST on the encoder
for min. 10 seconds (better 15), it will be restarted and initialized. The default Route IP of the
WEB-IF is 192.168.0.31 or 192.168.1.168 (This default Address may vary depending on model) after
initialization and can be recognized from the sticker at the bottom:

Step 2: Change the administrator’s computer IP

Set the administrator’s computer IP as: 192.168.0.* or 192.168.1.*to avoid IP conflicting with
the units own IP address IP 192.168.0.*: (use an IP setting “*” in the number range between
2-254 except .0.31 or .1.168) Remark: .0 is often the network router, .1 often the Gateway of
the used router.

Step 3: Login the menu with the web browser:

Enter 192.168.0.31 (or 192.168.1.168) in your Browser window.

Default user Name: admin

Default password: admin

You might end up in the chinese Language Menu if operating the unit for the first time: (That might
be obsolete depending on SW Versions...)

Author: Rri, August 2017, Version: V1.3 - 12

-
IRENIS Encoder & Streamers | User Manual

nd
So please change it to English using the submenu upper right corner use the 2 item:

You are entering the STATUS window:

You'll get more information if scrolling down:

The sub-menus are at the bottom.

Author: Rri, August 2017, Version: V1.3 - 13

-
IRENIS Encoder & Streamers | User Manual

Enter Network settings submenu (bottom-menu):

DHCP might not be a good idea because your local network router would handover an
IP Address from his pool which you can only get by entering the router itself.

Remark: DNS settings might not be necessary because the device would not need to
use them to translate domains <-> IP addresses.

Please change the settings to your local network values and scroll down to safe it by
pressing SET UP:

You can set the DNS values

according to your local router
values. The HTTP and RTSP
ports should be set for the unicast
/ http streaming default selected
ports

Author: Rri, August 2017, Version: V1.3 - 14

-
IRENIS Encoder & Streamers | User Manual

Enter the SYSTEMS Menu to reboot your device and to enable the new settings
or do a SW-update:

configure a planned scheduled restart:

Or upgrade the Firmware and initialize a reboot:

Author: Rri, August 2017, Version: V1.3 - 15

-
IRENIS Encoder & Streamers | User Manual

Do not forget to re-adjust your PC/LAPTOP IP-Settings to your local network addresses
if you changed the IP address.

Re-enter into the unit's WEB-IF by using the new address.

Author: Rri, August 2017, Version: V1.3 - 16

-
 IRENIS Encoder & Streamers | User Manual

5.1 STATUS DİSPLAY

Input status: when you input the HD signal source, it will show resolution of video input, if it’s
blank here: No video input detected .

Main-stream Status: Showing the resolution of the main-stream you set and multicast address.
You can control the multicast address by VLC or other Video receiving software supporting
that.

Second (Sub) stream Status: Showing the resolution of the second-stream and its configured
address:

Note: The Preview is only possible

if already configured:

Popup:

Please open FLV or HLS stream.

Author: Rri, August 2017, Version: V1.3 - 17

-
 IRENIS Encoder & Streamers | User Manual

5.2 NETWORK SETTINGS - WIFI

You can set the network with either Ethernet or WIFI. Only devices with WIFI support can use a
WLAN connection.

Instruction of wifi network Setup: 3 different settings can be chosen

A. Ethernet: Only connected by ethernet (default configuration)

B. Wifi: Only connect with WLAN . Hint: If you entered the wrong password or SSID during
WIFI mode will cause the system being unable to connect to Wirelesss LAN. Opening the web-
Interface will fail. Please press the reset button to restore the default settings to solve the
problem)
C. Auto: Automatically detect if you have ethernet or wifi connected.

Author: Rri, August 2017, Version: V1.3 - 18

-
 IRENIS Encoder & Streamers | User Manual

a. The Default IP of the device is 192.168.0.32 (depending on model) . If IP setting has been
forgotten after changing, you can RST= reset it to default IP following the reset to default
settings procedure like explained before.
b. If you don’t need to use a network cable, and when you reboot the device, it will access to
WIFI status if it’s equipped with WIFI . Please kindly note the different features for WIFI
versions.

5.3 MAIN STREAM ENCODING SETTINGS:

We assume, that the user already well knows the relevant terms and abbreviations for
Video-Encoding and their technical background.

Chose your codec:

Author: Rri, August 2017, Version: V1.3 - 19

-
IRENIS Encoder & Streamers | User Manual

MAİN STREAM SETTİNG:

 Enc type: h.264 & h.265 (is optional dep. on model)
Note: h.264 version can only use h.264 codec, h.265 model can both
 Profile: baseline profile / main profile / high profile ( note: h.265 version choose main
profile)
 Frame rate: 5-60 (If the input resolution is 720i/50,1080i50, the frame rate will be set to
25)
 Bitrate mode: VBR / CBR variable or constant (incl. zero pakets)
 Group of picture: 5-200, shows picture quality, default setting is almost sufficient
 Bitrate: 16-1200K (Network bandwidth setting)
Note: You can modify the above parameters without rebooting the encoder

SELECTİNG YOUR OUTPUT SCREEN SİZE/RESOLUTİON:

Note: The encoder is not intent to use for upscaling purpose i.e. 720 -> 1080. It
always depends on the Input resolution and size. Downscaling is possible:

Author: Rri, August 2017, Version: V1.3 - 20

-
IRENIS Encoder & Streamers | User Manual

Main - Stream protocol settings:

HTTP: /main enable/disable
HTTP port: 1-65535 optional
RTSP: /main enable/disable
RTSP port: 1-65535 optional
Multicast IP: 232.255.42.42 disable/RTP/UDP optional
Multicast port: 1-65535 optional
RTMP server IP: can be set according your streaming media server values
RTMP server port: 1-65535 optional
RTMP app name: can be set by yourself
RTMP stream name: can be set by yourself
RMTP user name: User for your server
RMTP password name: and Password for your server
ONVIF : enable/disable (IP-Camera protocol support)

Note: ONVIF Settings depending on SW and device model types

Note: We recommend to chose not all streams and protocolls at the same time.

Author: Rri, August 2017, Version: V1.3 - 21

-
IRENIS Encoder & Streamers | User Manual

Note: For TS URL, HLS URL, RTSP URL, the Network IP address of the device is the Unicast
distribution address. You do not need to fill in this addrerss by yourself becasue its already related
to the GbE network IP.
Multicast IP adresses and ports need to be considered in the IANNA recommended range to avoid
conflicts within your local network and router/switches:

https://www.iana.org/assignments/multicast-addresses/multicast-addresses.xhtml

TS once pack:

is the packet size send by the encoder streamer.

Usually we suggest to set it to 7.
For example for UDP:
1 packet is 188, 7 pack size will be 188*7+46=1362

Author: Rri, August 2017, Version: V1.3 - 22

-
IRENIS Encoder & Streamers | User Manual

MAİN STREAM LİVE VİEW:

You can play the stream address by your computer if you installed i.e. the VLC Player software
or use an IPTV STB by setup the RTSP or HTTP stream addresses:
Easiest way: copy and paste the URL from the main window

and open VLC – network stream:

Press Play/Wiedergabe:

Author: Rri, August 2017, Version: V1.3 - 23

-
IRENIS Encoder & Streamers | User Manual

You can check the video information if you like by VLC:

Author: Rri, August 2017, Version: V1.3 - 24

-
 IRENIS Encoder & Streamers | User Manual

Second stream Live View: You can play the stream address by your computer if you installed
the Video Lan Client (VLC , freeware for almost all plattforms) similar to the shown procedure
above.
CVBS Live View (depending on Model): You can play the stream address by your computer if
you installed the VLC.

5.4 OSD SETTINGS (OVERL AY A PICTURE/ TX T TO THE ENCODED S TRE AM )

To be able to OVERLAY text and advertisements to your encoded stream, the unit supports up to
4 zones:

Note: You can insert two couples of TEXT and 3 pictures simultaneously overlaying the picture
Tex1 X: 0-1920 is optional, display the left and right position of the text
Tex1 X: 0-1080 is optional, display the up and down position of the text
Font1 size: 8-72 is optional
Alpha1: 0-128 is optional, Alpha-blending – transparency setting
Color1: choose the color you want to display
Bg1: choose background color for the text on the video overlay

Author: Rri, August 2017, Version: V1.3 - 25

-
IRENIS Encoder & Streamers | User Manual

Tex1: input the content of the text you want to display

These features are varying depending on model and versions.

or a prepared picture according to the values given in the WEB-IF for uploading to the unit:

looks like there is a translation issue of the upload-button ;-)

OSD insertion Picture Setting

Picture1…4: disable/ enable (disable: no images , enable: insert the images)
Pictures X: 4-1920 is optional to set the left and right position of the picture
Pictures Y: 4-1080 is optional to set the up and down position of the picture
Alphal: 0-128 is optional
Picture1 name: display the name of the picture1
Upload picture1: choose to upload the image, supporting *.bmp format of the picture and
limited filesize : less than 500kbyte
Requirements
• The settings of the three pictures to be inserted must be identical.
• Transparent background of the picture setting:
should be of RGB values: R－177，G－204，B－233 or see WEBIF hints
Author: Rri, August 2017, Version: V1.3 - 26
-
IRENIS Encoder & Streamers | User Manual

example:

Picture quality setting (dep. on model)

Brightness: 0-100 is optional (to adjust the brightness of the image)
Contrast: 0-100 is optional (to adjust the contrast of the image)
Hue: 0-100 is optional (to adjust the hue of the image)
Saturation: 0-100 is optional (to adjust the saturation of the image)

Author: Rri, August 2017, Version: V1.3 - 27

-
IRENIS Encoder & Streamers | User Manual

CSC:

is for Video color, Contrast & brightness settings just in case the user want
to change them appart from the original passed Picture settings.

HINT: If you change parameters or enable features, following popup message will
appear:

This doesn't mean to restart your encoder! – It means your Receiver should be tuned
again to the stream (i.e. switch or reload the channel on your Irenis IPTV SetTopBox to
re-initialize the decoding process)

Author: Rri, August 2017, Version: V1.3 - 28

-
 IRENIS Encoder & Streamers | User Manual

SECOND (SUB) STREAM OUTPUT SETTINGS

Note: The method of the setting is nearly the same with mainstream code setting:

The sub-Stream has some slightly different setup:

Because the RTMP Server can only obtain a stream once from the same address.

Author: Rri, August 2017, Version: V1.3 - 29

-
 IRENIS Encoder & Streamers | User Manual

Please asure the corresponding picture settings if downscaling i.e. from 16:9 to 5:4 would
squeeze the picture:

5.5 CVBS ENCODING SETTINGS (DEP. ON MODEL)

Author: Rri, August 2017, Version: V1.3 - 30

-
 IRENIS Encoder & Streamers | User Manual

5.6 AUDIO ENCODING SETTINGS

Audio bitrates: 48k, 64k, 128k, 160k, 192k, 256k

Audio type: AAC (depending on model) and more...
Audio digital gain: 2x, 4x, 8x, used to adjust volume
Audio input mode: digital/analog
Example 1:

Example 2:

Author: Rri, August 2017, Version: V1.3 - 31

-
IRENIS Encoder & Streamers | User Manual

6 WIFI SETTING HİNTS

Hint shown above: If you want to configure the HD encoder, you need to set the fixed IP of the
computer first . See chapter above – similar to Ethernet Settings.

6.1 HD WIRELESS ENCODER SETTINGS

Connect the HD Encoders by the network cable, then open the browser to enter the network
setting chapter. Default setting as shown below can be modified to your needs:

Note:
1) Default IP of wifi can be 192.168.0.32 . When wifi connected successfully, you can access
to web control panel by 192.168.0.32 .
2) Wifi Encryption : WPA/WPA2 (Note: Some wireless routers have different encryption
mode, please select WPA/WPA2 for the encryption )
3) Input the WEP/WPA password string of the wireless router

Author: Rri, August 2017, Version: V1.3 - 32

-
IRENIS Encoder & Streamers | User Manual

7 TECHNICAL SPECIFICATIONS (DEP. ON MODEL)

Video
Input HDMI, SDI, CVBS according to the chosen model
Resolution 1920×1080_60i/60P, 1920×1080_50i, 1280×720_60p,
1280×720_50p and below
Encoding H.264/AVC Main Profile/High Profile ; H.265/HEVC Baseline
Profile; Audio AAC
Data Rate 0.8 Mbps ... 12 Mbps
Rate Control CBR/VBR
GOP Structure IBBP
Advanced Pretreatment De-interlacing, Noise Reduction, Sharpening

Audio
Encoding AAC, MP3
Sampling Rate Auto
Bit-rate 48K/64K/96K/128K/160K/192K/256k
Sampling Precision 16 bit
Data Rate 64 Kbps ~ 384 Kbps

System
System Support WINDOWS; LINUX
Ethernet/RJ45 1000Base-T Ethernet interface
Protocol HTTP, UDP, RTP, RTSP, RTMP, ONVIF (prot.: S,C,G)
Control Interface 100baseT by WEB-Browser

SAFETY AND OTHER RECOMMENDATİONS:

Assure climatic environment rules for electronic machines like this, Grounding rules as
well. Installation should be done by a certified electrician.

Important Notes!
This manual is for use by qualified personnel only. Handling this device or system requires special
electronic technical knowledge. To reduce the risk of electrical shock or damage to the equipment,
do not perform any servicing other than the installation and operating instructions contained in this
manual unless you are qualified to do so. This device operates in the given voltage and frequency
range without requiring manual adjustment.
Do not open the top case w/o unplugged power source because serious injury or death may be
the result! Inside are components under risk from electrostatic discharge. To avoid equipment
damages do not touch these components or, observe the respective handling rules!
For continued protection against fire, the fuses may only be replaced by identical fuses with the
same electrical specifications which are designed for the corresponding fuse positions.
No part of this publication may be reproduced in any form or by any means or used to make any
derivative work (such as translation, transformation or adaptation) without the written permission
from Blankom / IRENIS GmbH.

Author: Rri, August 2017, Version: V1.3 - 33

-
IRENIS Encoder & Streamers | User Manual

IRENIS GmbH reserves the right to revise this publication and make changes in its content from
time to time, whereby it shall not be obligatory for IRENIS GmbH to provide notification of such
revision or change.
IRENIS GmbH provides this manual without warranty of any kind, neither implied nor expressed,
this
includes also any warranties regarding the merchantability and fitness for a particular purpose.
IRENIS GmbH may improve this manual or make changes in the products described herein at any
point of time.

Installation Notes
All types of the IRENIS-BLANKOM family are single or 19“devices with 1 RU height might be
designed for installation in 19” racks. In addition to the front panel screws an internal module
support is required at the rack. Depending on the Frontend used and the operating adjustments,
the RF-input port carries DC Voltage (13V /18V, max. 400 mA).
By connecting a mains cable, the device can become functional without any auxiliary appliances.
The power supply units are designed for the wide range of 100-230V AC; a manual adjustment of
the voltage is not necessary.
For some models the second power connector is feeding another independent power supply for
internal redundancy. For a maximum of redundancy both power supplies should use different
circuits.
All the outputs are decoupled from one another. Thus, the circuit does not have any effect on the
functioning of the device. Connections that are not required need not to be terminated.
Suggestion: CAT 6E Ethernet cable for GbEthernet

CONTACT:

IRENIS GmbH
Owiesenkehre 1
D-22177 Hamburg - Germany

Managing Director: Dipl.Ing. Riccardo Rossini

Commercial Register: HRB 130657 / District Court Hamburg
Web: www.blankom.de E-Mail: [email protected] / [email protected]
Irenis-Direct Phone: +49 40 459747 Technical Hotline: +49 40 22864848

Author: Rri, August 2017, Version: V1.3 - 34

-