Data Sheet PIUHFENd

Ultipleat® High Flow Series

Filter Cartridges

Description
The Ultipleat® High Flow filter is a large-diameter, coreless,
single open-ended, pleated cartridge with an inside-to-
outside flow pattern.

The filter’s unique crescent-shaped pleat geometry,

combined with its large 152.4 mm (6-inch) diameter and
proprietary range of available Pall filter media, allows you
to use significantly fewer filters and smaller housings for
high flow-rate applications.

Features and Benefits

• Coreless large diameter cartridge, synthetic construction,
to minimize waste disposal
• High flow rate per filter cartridge
♦ Up to 40 times fewer cartridges to change out
♦ Up to 50% smaller filter system possible
• Available in a variety of filter lengths and grades
• Absolute-rated filter medium for reproducible performance
• Features proprietary unique crescent-shaped pleat
geometry
• Inside-to-outside flow pattern that traps contaminant
inside the element, thus preventing polluting the treated
water during the cartridge change-out
• Handle for easy cartridge replacement

Materials of Construction

Filter Medium Filter Medium Support/Drainage End Caps Wrap Materials

Type Materials
HDC® II Medium High-Area Polypropylene Polypropylene Glass-Filled Polypropylene and
Structure Polypropylene Polyolefin Hotmelt
Profile® Medium in Pleated Polypropylene Polypropylene Glass-Filled Polypropylene
Ultipleat Format Depth Structure Polypropylene
Ultipor® GF Resin Bonded Glass Fiber / Polyester / Nylon Glass-Filled Polyester and
Medium Polyester Support Acetal Polyamide Hotmelt
Ultipleat CAS Pleated Polypropylene / Polypropylene Glass-Filled Polypropylene
Medium Polyether Sulfone Membrane Polypropylene
Operating Conditions1
Polypropylene Medium/ Glass Fiber Medium
CAS Composite Medium
Maximum Differential Pressure2 3.44 bard at 82˚C 3.44 bard at 121˚C
(normal inside-to-outside flow) 50 psid at 180˚F 50 psid at 250˚F
1) Maximum temperature in aqueous systems is 60°C / 140°F for GF medium.
2) For fluids compatible with the filter element at the stated temperature.

Ordering Information/Specifications
Filter Cartridge Part Number: HFU s l u Code-Filter O-Ring u Material
Code Filter Dimensions, Suggested Maximum H13 (Standard for glass fiber Nitrile
s (nominal) Water Flow Per Cartridge- and aramid fiber filters)
Diameter (in / mm) US gpm / L /min / MGD H13U 3 Nitrile U-Cup
x Length (in / mm)
J (Standard for Ethylene Propylene
620 6 / 152.4 x 20 / 508 175 / 663 / 0.25 polypropylene filters)
640 6 / 152.4 x 40 / 1016 350 / 1325 / 0.5 JU 3 Ethylene Propylene U-Cup
660 6 / 152.4 x 60 / 1524 500 / 1900 / 0.7 H4 Silicone
680 6 / 152.4 x 80 / 2032 500 / 1900 / 0.7 H Fluoroelastomer
3) U-Cup seal is standard for the 1 micron composite filter.

Filter Cartridge Pressure Drop (typical) per Filter Length Shown4

Medium Grade Absolute Liquid 508 mm / 20 inch length 1016 mm /40 inch length 1524 mm / 60 inch length 2032 mm / 80 inch length
Type l Removal Rating
(microns) at 99.98% psid/100gpm mbar/M3/hr psid/100gpm mbar/M3/hr psid/100gpm mbar/M3/hr psid/100gpm mbar/M3/hr
by particle count5
HDC II J060 6 0.158 0.48 0.080 0.24 0.058 0.17 0.040 0.12
Medium J100 10 0.120 0.36 0.060 0.18 0.040 0.12 0.030 0.09
J200 20 0.100 0.30 0.050 0.15 0.033 0.10 0.025 0.08
Profile UY0206 2 1.091 3.31 0.540 1.64 0.362 1.10 0.270 0.82
Medium in UY045 4.5 0.489 1.48 0.242 0.73 0.162 0.49 0.121 0.37
Ultipleat UY060 6 0.395 1.20 0.196 0.59 0.131 0.40 0.098 0.30
Format UY100 10 0.344 1.04 0.170 0.52 0.114 0.35 0.085 0.26
UY200 20 0.243 0.74 0.120 0.36 0.080 0.24 0.060 0.18
UY4007 40 0.182 0.55 0.090 0.27 0.060 0.18 0.045 0.14
UY7007 70 0.040 0.12 0.020 0.06 0.013 0.04 0.010 0.03
UY10007 90 0.027 0.08 0.013 0.04 0.009 0.03 0.007 0.02
Ultipor GF GF020 2 0.219 0.66 0.110 0.33 0.073 0.22 0.055 0.17
Medium GF060 6 0.180 0.55 0.090 0.27 0.060 0.18 0.045 0.14
GF100 10 0.159 0.48 0.080 0.24 0.053 0.16 0.040 0.12
GF200 20 0.119 0.36 0.060 0.18 0.040 0.12 0.030 0.09
GF400 7 29 0.100 0.30 0.050 0.15 0.033 0.10 0.025 0.08
Ultipleat CAS010 1 1.496 4.54 0.740 2.25 0.496 1.51 0.370 1.12
CAS
Medium

4) Multiply this value by the total system flow to determine the aqueous pressure drop. For fluids other than water, multiply this value by the fluid’s
viscosity at the operating temperature in centipoise. This value is the pressure drop across the Ultipleat High Flow filter(s) only; it must be added
to the pressure drop contribution from the Ultipleat High Flow filter housing.
5) The test procedure used is an adaptation of ISO 4572, modified to determine the micron size above which particles are quantitatively removed.
6) 2 micron at 99% efficiency.
7) Precision evaluation of the 99.98% removal efficiency for these coarse grades is not possible with the ISO modified test procedure utilized. The
removal efficiency was determined by the maximum spherical particle analysis.

Visit us on the Web at www.pall.com

Pall Corporation has offices and plants throughout the world. For Pall representatives in your
25 Harbor Park Drive area, please go to www.pall.com/contact
Port Washington, NY 11050 Because of technological developments related to the products, systems, and/or services
+1 516 484 3600 telephone described herein, the data and procedures are subject to change without notice. Please
+1 800 289 7255 toll free US consult your Pall representative or visit www.pall.com to verify that this information remains
valid. Products in this document may be covered by one or more patent numbers. For a
complete list of Pall’s patents please visit www.pall.com/main/about-pall/patents.page.
Portsmouth-UK
+44 (0)23 9230 3303 telephone
+44 (0)23 9230 2507 fax © Copyright 1999, 2015 Pall Corporation. Pall, , Ultipleat, HDC, Ultipor, and Profile are trademarks of Pall
Corporation.
® Indicates a Pall trademark registered in the USA. Filtration. Separation. Solution.SM and BETTER LIVES. BET-
TER PLANET. are service marks of Pall Corporation.

PIUHFENd Produced in the USA November 2015