Scribd
Upload
31 views8 pages

Mazda Manual

Uploaded by

Jemeca Mejias
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
31 views8 pages

Mazda Manual

Uploaded by

Jemeca Mejias
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

18

MAZDA
MAZDA MANUAL

CONTENTS
APPLICATIONS
7

SPECIAL FUNCTIONS

REMOTE CONTROL PROGRAMMING

15

18
APPLICATIONS

VEHICLE YEAR KEY TYPE


7 PROG
626 ALL Y LUCAS
XEDOS ALL Y LUCAS
DEMIO ALL Y LUCAS
121 ALL Y PATS

15

18
SPECIAL FUNCTIONS
MAZDA CODE CONVERTER

VEHICEL SELECTION

LEXUS From the VEHICLE SELECTION MENU 7


MAZDA
select MAZDA.
MITSUBISHI
NISSAN

PRESS ENTER KEY

DIAGNOSTIC MENU
> PATS 2
> P.C.M Select MAZDA PIN CODE
> MAZDA PIN CODE

PRESS ENTER KEY 15

Press ENTER Key


MAZDA CODE CONVERTER
18

PRESS ENTER KEY


Enter serial number from LUCAS Im-
SERIAL CODE
mobiliser mounted at the back of the
IGNITION KEY assembly.
__________
Code can be found on the label.
IS CODE CORRECT
OK=ENTER CLEAR=BACK NOTE : ONLY LUCAS IMMOBILISERS
WILL WORK CORRECTLY.
MAZDA MECS
Please WAIT for the code to be calcu-
PLEASE WAIT lated.

NOTE : THIS WILL TAKE 10


MINUTES !
SPECIAL FUNCTIONS
MAZDA CODE CONVERTER

MAZDA MECS

SER No. The screen will then display the


7 603-611-2057 converted pin code.
PINCODE : 7355-4316

PRESS ENTER KEY

KEY PROGRAMMING PROCEDURE

PROCEDURE FOR WHEN THERE ARE NO KEYS OR ONLY 1 PREPROGRAMMED KEY


AND YOU NEED TO PROGRAM MORE KEYS

IMPORTANT : You must have at least 2 keys to perform this procedure. If


there are no pre-programmed keys, you will have to provide 2 new keys. If
there is only one pre-programmed key, you will have to provide at least one
15 more.

IMPORTANT : YOU MUST USE A FACTORY KEY TO PROGRAM, YOU CANNOT


USE AFTERMARKET KEYS FOR THIS PROCEDURE.

18 1. Cut the mechanical cuts on each new transponder key.


2. Insert the first key and turn the ignition ON and then back to the OFF posi-
tion 5 times. You must NOT leave the ignition in the ON position for more
than 1 second.
3. Turn the key back to ON position and watch the flashing security light on
the Dashboard. The light should flash rapidly, 300 mS ON and 300mS OFF.
4. Within 20 seconds, turn the key to the LOCK position for 5 minutes. After 5
minutes the security light should decrease in flashing to 1.2 seconds be-
tween flashes.
5. Within 20 seconds, enter the CODEWORD (Password). NOTE : SEE HOW TO
ENTER CODEWORD under the Mazda code converter section.
6. When you have entered the codeword, the security light should remain ON
and not flash.
7. The car should now start. Start the car and the security light should stay lit
for between 1 and 2 seconds.
8. Within 20 seconds, remove the first key and insert the second key and start
the car. The security light should stay lit for between 1 to 2 seconds.
9. Stop if you have no more keys, and wait 30 seconds for the car to exit pro-
gramming mode.
SPECIAL FUNCTIONS
PROGRAMMING PROCEDURE

PROCEDURE FOR WHEN THERE ARE 2 OR MORE PREPROGRAMMED KEYS

1. Cut the mechanical cuts on each new transponder key.


2. Insert the first key and turn the ignition ON and then back to the OFF posi- 7
tion 5 times. You must NOT leave the ignition in the ON position for more
than 1 second.
3. Turn the first pre-programmed key back to the ON position, the security
light should stay ON.
4. Turn the first key back to the LOCK position.
5. Insert the second pre-programmed key and start the car. The security light
should stay lit for between 1 and 2 seconds. Turn back to the LOCK position
and remove key.
6. Insert the first pre-programmed key and start the car. The security light
should stay lit for between 1 and 2 seconds. Turn back to the LOCK position
and remove key.
7. Insert the next pre-programmed key or a new key and start the car. The
security light should stay lit for between 1 and 2 seconds. Turn back to the
LOCK position and remove key. Repeat for any further additional keys, up 15
to 8 maximum in total.
8. Stop if you have no more keys, and wait 30 seconds for the car to exit pro-
gramming mode.

HOW TO ENTER THE CODEWORD (PASSWORD) 18

The Codeword can be obtained by inserting the serial number from the Immobi-
liser ECU into the Mazda Code program on the tester. The codeword is 8 digits.
(For this procedure we will use : 23234223)

1. Before you start, the security light on the dash should be flashing on and
off for 1.2 seconds each for ON and OFF.
2. Turn the ignition key to the ON position while the security light is not illumi-
nated. Count the illumination flashes 2 times while the light is not illumi-
nated and turn the key to the lock position.
3. Within 30 seconds of turning the key to the LOCK position, turn the ignition
key to the ON position while the security light is not illuminated. Count the
illumination flashes 3 times while the light is not illuminated and turn the
key to the lock position.
SPECIAL FUNCTIONS
4 Within 30 seconds of turning the key to the LOCK position, turn the ignition
key to the ON position while the security light is not illuminated. Count the
illumination flashes 2 times while the light is not illuminated and turn the
key to the lock position.
5 Within 30 seconds of turning the key to the LOCK position, turn the ignition
7 key to the ON position while the security light is not illuminated. Count the
illumination flashes 3 times while the light is not illuminated and turn the
key to the lock position.
6 Within 30 seconds of turning the key to the LOCK position, turn the ignition
key to the ON position while the security light is not illuminated. Count the
illumination flashes 4 times while the light is not illuminated and turn the
key to the lock position.
7 Within 30 seconds of turning the key to the LOCK position, turn the ignition
key to the ON position while the security light is not illuminated. Count the
illumination flashes 2 times while the light is not illuminated and turn the
key to the lock position.
8 Within 30 seconds of turning the key to the LOCK position, turn the ignition
key to the ON position while the security light is not illuminated. Count the
illumination flashes 2 times while the light is not illuminated and turn the
15 key to the lock position.
9 Within 30 seconds of turning the key to the LOCK position, turn the ignition
key to the ON position while the security light is not illuminated. Count the
illumination flashes 3 times while the light is not illuminated and turn the
key to the lock position.
18 10 If you have entered the code correctly the security light will stop flashing
and stay illuminated. If a mistake has been made, wait 45 seconds and try
again.

NOTE 1 : The ignition key should not be turned ON twice within one non illumi-
nation cycle.
NOTE 2 : The ignition key should not be turned ON during an illumination cycle.
NOTE 3 : The ignition key should not be turned to LOCK twice within one illumi-
nation cycle.
REMOTE CONTROL PROGRAMMING
626

1. Make sure the drivers side door is open.


2. Turn Ignition ON, and then back OFF.
3. Remove the key , and then repeat steps 1-2 2 more times.
4. Press the light switch that operates the courtesy light on the drivers door A post, and make
sure the light goes out. Repeat this 2 times. 7
5. When the car makes a beep sound, press the Lock button on the remote control 2 times, the
car should make a beep sound.
6. Repeat for additional remote.

2004 Mazda 3

Procedure

1. Open driver side door and leave open.


2. Lock and Unlock the drivers door using the power door lock switch on the door.
3. Insert key into the ignition.
4. Turn Key to ON position and return to Lock (off) position. Do this 3 times within 10 seconds.
LEAVE key in the ignition in Lock (off) position.
5. Close and open the drivers door 3 times. Leave door open after this step
6. ECU should respond by locking and unlocking the doors once.
7. Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.
8. Additional remotes, repeat Step 7 for up to 3 remotes total.
15
9. Remove the key from the ignition and the ECU will respond a final time with a series
(about four ) of door locks and unlocks. Procedure complete.

18

You might also like