Operational amplifier

From Wikipedia, the free encyclopedia

Jump to: navigation, search

A Signetics μa741 operational amplifier, one of the most successful op-amps.

An operational amplifier ("op-amp") is a DC-coupled high-gain electronic voltage amplifier
with a differential input and, usually, a single-ended output.[1] An op-amp produces an output
voltage that is typically hundreds of thousands times larger than the voltage difference between
its input terminals.[2]
Operational amplifiers are important building blocks for a wide range of electronic circuits. They
had their origins in analog computers where they were used in many linear, non-linear and
frequency-dependent circuits. Their popularity in circuit design largely stems from the fact that
characteristics of the final elements (such as their gain) are set by external components with little
dependence on temperature changes and manufacturing variations in the op-amp itself.
Op-amps are among the most widely used electronic devices today, being used in a vast array of
consumer, industrial, and scientific devices. Many standard IC op-amps cost only a few cents in
moderate production volume; however some integrated or hybrid operational amplifiers with
special performance specifications may cost over $100 US in small quantities. Op-amps may be
packaged as components, or used as elements of more complex integrated circuits.
The op-amp is one type of differential amplifier. Other types of differential amplifier include the
fully differential amplifier (similar to the op-amp, but with two outputs), the instrumentation
amplifier (usually built from three op-amps), the isolation amplifier (similar to the
instrumentation amplifier, but with tolerance to common-mode voltages that would destroy an
ordinary op-amp), and negative feedback amplifier (usually built from one or more op-amps and
a resistive feedback network).

Contents
[hide]
• 1 Circuit notation
• 2 Operation
○ 2.1 Ideal and real op-amps
• 3 History
○ 3.1 1941: First (vacuum tube) op-amp
○ 3.2 1947: First op-amp with an explicit non-inverting input
○ 3.3 1949: First chopper-stabilized op-amp
○ 3.4 1961: First discrete IC op-amps
○ 3.5 1962: First op-amps in potted modules
○ 3.6 1963: First monolithic IC op-amp
○ 3.7 1966: First varactor bridge op-amps
○ 3.8 1968: Release of the μA741
○ 3.9 1970: First high-speed, low-input current FET design
○ 3.10 1972: Single sided supply op-amps being produced
○ 3.11 Recent trends
• 4 Classification
• 5 Applications
○ 5.1 Use in electronics system design
○ 5.2 Basic single stage amplifiers
 5.2.1 Non-inverting amplifier
 5.2.2 Inverting amplifier
○ 5.3 Positive feedback configurations
○ 5.4 Positive voltage level detector
○ 5.5 Negative voltage level detector
○ 5.6 Sine to square wave converter
○ 5.7 Other applications
• 6 Limitations of real op-amps
○ 6.1 DC imperfections
○ 6.2 AC imperfections
○ 6.3 Non-linear imperfections
○ 6.4 Power considerations
• 7 Internal circuitry of 741 type op-amp
○ 7.1 Input stage
 7.1.1 Constant-current stabilization system
 7.1.2 Differential amplifier
 ○ 7.2 Class A gain stage
○ 7.3 Output bias circuitry
○ 7.4 Output stage
• 8 See also
• 9 Notes
• 10 References
• 11 Further reading
• 12 External links

[edit] Circuit notation

Circuit diagram symbol for an op-amp

The circuit symbol for an op-amp is shown to the right, where:

• : non-inverting input

• : inverting input

• : output

• : positive power supply

• : negative power supply

The power supply pins ( and ) can be labeled in different ways (See IC power supply
pins). Despite different labeling, the function remains the same — to provide additional power
for amplification of the signal. Often these pins are left out of the diagram for clarity, and the
power configuration is described or assumed from the circuit.
[edit] Operation
The amplifier's differential inputs consist of a input and a input, and ideally the op-amp
amplifies only the difference in voltage between the two, which is called the differential input
voltage. The output voltage of the op-amp is given by the equation,
where is the voltage at the non-inverting terminal, is the voltage at the inverting terminal
and AOL is the open-loop gain of the amplifier. (The term "open-loop" refers to the absence of a
feedback loop from the output to the input).

Typically the op-amp's very large gain is controlled by negative feedback, which largely determines the
magnitude of its output ("closed-loop") voltage gain in amplifier applications, or the transfer function required
(in analog computers). Without negative feedback, and perhaps with positive feedback for regeneration, an op-
amp acts as a comparator. High input impedance at the input terminals and low output impedance at the output
terminal(s) are important typical characteristics.
With no negative feedback, the op-amp acts as a comparator. The inverting input is held at ground (0 V) by the
resistor, so if the Vin applied to the non-inverting input is positive, the output will be maximum positive, and if
Vin is negative, the output will be maximum negative. Since there is no feedback from the output to either
input, this is an open loop circuit. The circuit's gain is just the GOL of the op-amp.

Adding negative feedback via the voltage divider Rf,Rg reduces the gain. Equilibrium will be established when
Vout is just sufficient to reach around and "pull" the inverting input to the same voltage as Vin. As a simple
example, if Vin = 1 V and Rf = Rg, Vout will be 2 V, the amount required to keep V– at 1 V. Because of the
feedback provided by Rf,Rg this is a closed loop circuit. Its over-all gain Vout / Vin is called the closed-loop gain
ACL. Because the feedback is negative, in this case ACL is less than the AOL of the op-amp.
The magnitude of AOL is typically very large—10,000 or more for integrated circuit op-amps—

and therefore even a quite small difference between and drives the amplifier output nearly
to the supply voltage. This is called saturation of the amplifier. The magnitude of AOL is not well
controlled by the manufacturing process, and so it is impractical to use an operational amplifier
as a stand-alone differential amplifier. If predictable operation is desired, negative feedback is
used, by applying a portion of the output voltage to the inverting input. The closed loop feedback
greatly reduces the gain of the amplifier. If negative feedback is used, the circuit's overall gain
and other parameters become determined more by the feedback network than by the op-amp
itself. If the feedback network is made of components with relatively constant, stable values, the
unpredictability and inconstancy of the op-amp's parameters do not seriously affect the circuit's
performance.
If no negative feedback is used, the op-amp functions as a switch or comparator.
Positive feedback may be used to introduce hysteresis or oscillation.
[edit] Ideal and real op-amps

An equivalent circuit of an operational amplifier that models some resistive non-ideal

parameters.
An ideal op-amp is usually considered to have the following properties, and they are considered
to hold for all input voltages:
• Infinite open-loop gain (when doing theoretical analysis, a limit may be taken as open
loop gain AOL goes to infinity).
• Infinite voltage range available at the output (vout) (in practice the voltages available from

the output are limited by the supply voltages and ). The power supply sources are
called rails.
• Infinite bandwidth (i.e., the frequency magnitude response is considered to be flat
everywhere with zero phase shift).

• Infinite input impedance (so, in the diagram, , and zero current flows from
to ).
• Zero input current (i.e., there is assumed to be no leakage or bias current into the device).

• Zero input offset voltage (i.e., when the input terminals are shorted so that , the
output is a virtual ground or vout = 0).
• Infinite slew rate (i.e., the rate of change of the output voltage is unbounded) and power
bandwidth (full output voltage and current available at all frequencies).
• Zero output impedance (i.e., Rout = 0, so that output voltage does not vary with output
current).
 • Zero noise.
• Infinite Common-mode rejection ratio (CMRR).
• Infinite Power supply rejection ratio for both power supply rails.
These ideals can be summarized by the two "golden rules":
I. The output attempts to do whatever is necessary to make the voltage difference
between the inputs zero.
II. The inputs draw no current.[3]:177
The first rule only applies in the usual case where the op-amp is used in a closed-loop design
(negative feedback, where there is a signal path of some sort feeding back from the output to the
inverting input). These rules are commonly used as a good first approximation for analyzing or
designing op-amp circuits.[3]:177
In practice, none of these ideals can be perfectly realized, and various shortcomings and
compromises have to be accepted. Depending on the parameters of interest, a real op-amp may
be modeled to take account of some of the non-infinite or non-zero parameters using equivalent
resistors and capacitors in the op-amp model. The designer can then include the effects of these
undesirable, but real, effects into the overall performance of the final circuit. Some parameters
may turn out to have negligible effect on the final design while others represent actual limitations
of the final performance, that must be evaluated.
[edit] History

GAP/R's K2-W: a vacuum-tube op-amp (1953)

ADI's HOS-050: a high speed hybrid IC op-amp (1979)

An op-amp in a modern DIP

[edit] 1941: First (vacuum tube) op-amp
An op-amp, defined as a general-purpose, DC-coupled, high gain, inverting feedback amplifier,
is first found in U.S. Patent 2,401,779 "Summing Amplifier" filed by Karl D. Swartzel Jr. of Bell
labs in 1941. This design used three vacuum tubes to achieve a gain of 90 dB and operated on
voltage rails of ±350 V. It had a single inverting input rather than differential inverting and non-
inverting inputs, as are common in today's op-amps. Throughout World War II, Swartzel's design
proved its value by being liberally used in the M9 artillery director designed at Bell Labs. This
artillery director worked with the SCR584 radar system to achieve extraordinary hit rates (near
90%) that would not have been possible otherwise.[4]
[edit] 1947: First op-amp with an explicit non-inverting input
In 1947, the operational amplifier was first formally defined and named in a paper by Professor
John R. Ragazzini of Columbia University. In this same paper a footnote mentioned an op-amp
design by a student that would turn out to be quite significant. This op-amp, designed by Loebe
Julie, was superior in a variety of ways. It had two major innovations. Its input stage used a long-
tailed triode pair with loads matched to reduce drift in the output and, far more importantly, it
was the first op-amp design to have two inputs (one inverting, the other non-inverting). The
differential input made a whole range of new functionality possible, but it would not be used for
a long time due to the rise of the chopper-stabilized amplifier.[5]
[edit] 1949: First chopper-stabilized op-amp
In 1949, Edwin A. Goldberg designed a chopper-stabilized op-amp.[6] This set-up uses a normal
op-amp with an additional AC amplifier that goes alongside the op-amp. The chopper gets an AC
signal from DC by switching between the DC voltage and ground at a fast rate (60 Hz or
400 Hz). This signal is then amplified, rectified, filtered and fed into the op-amp's non-inverting
input. This vastly improved the gain of the op-amp while significantly reducing the output drift
and DC offset. Unfortunately, any design that used a chopper couldn't use their non-inverting
input for any other purpose. Nevertheless, the much improved characteristics of the chopper-
stabilized op-amp made it the dominant way to use op-amps. Techniques that used the non-
inverting input regularly would not be very popular until the 1960s when op-amp ICs started to
show up in the field.
In 1953, vacuum tube op-amps became commercially available with the release of the model K2-
W from George A. Philbrick Researches, Incorporated. The designation on the devices shown,
GAP/R, is an acronym for the complete company name. Two nine-pin 12AX7 vacuum tubes
were mounted in an octal package and had a model K2-P chopper add-on available that would
effectively "use up" the non-inverting input. This op-amp was based on a descendant of Loebe
Julie's 1947 design and, along with its successors, would start the widespread use of op-amps in
industry.
[edit] 1961: First discrete IC op-amps

GAP/R's model P45: a solid-state, discrete op-amp (1961).

With the birth of the transistor in 1947, and the silicon transistor in 1954, the concept of ICs
became a reality. The introduction of the planar process in 1959 made transistors and ICs stable
enough to be commercially useful. By 1961, solid-state, discrete op-amps were being produced.
These op-amps were effectively small circuit boards with packages such as edge-connectors.
They usually had hand-selected resistors in order to improve things such as voltage offset and
drift. The P45 (1961) had a gain of 94 dB and ran on ±15 V rails. It was intended to deal with
signals in the range of ±10 V.
[edit] 1962: First op-amps in potted modules

GAP/R's model PP65: a solid-state op-amp in a potted module (1962)

By 1962, several companies were producing modular potted packages that could be plugged into
printed circuit boards.[citation needed] These packages were crucially important as they made the
operational amplifier into a single black box which could be easily treated as a component in a
larger circuit.
[edit] 1963: First monolithic IC op-amp
In 1963, the first monolithic IC op-amp, the μA702 designed by Bob Widlar at Fairchild
Semiconductor, was released. Monolithic ICs consist of a single chip as opposed to a chip and
discrete parts (a discrete IC) or multiple chips bonded and connected on a circuit board (a hybrid
IC). Almost all modern op-amps are monolithic ICs; however, this first IC did not meet with
much success. Issues such as an uneven supply voltage, low gain and a small dynamic range held
off the dominance of monolithic op-amps until 1965 when the μA709[7] (also designed by Bob
Widlar) was released.
[edit] 1966: First varactor bridge op-amps
Since the 741, there have been many different directions taken in op-amp design. Varactor bridge
op-amps started to be produced in the late 1960s. They were designed to have extremely small
input current and are still amongst the best op-amps available in terms of common-mode
rejection with the ability to correctly deal with hundreds of volts at their inputs.
[edit] 1968: Release of the μA741
The popularity of monolithic op-amps was further improved upon the release of the LM101 in
1967, which solved a variety of issues, and the subsequent release of the μA741 in 1968. The
μA741 was extremely similar to the LM101 except that Fairchild's facilities allowed them to
include a 30 pF compensation capacitor inside the chip instead of requiring external
compensation. This simple difference has made the 741 the canonical op-amp and many modern
amps base their pinout on the 741s. The μA741 is still in production, and has become ubiquitous
in electronics—many manufacturers produce a version of this classic chip, recognizable by part
numbers containing 741. The same part is manufactured by several companies.
[edit] 1970: First high-speed, low-input current FET design
In the 1970s high speed, low-input current designs started to be made by using FETs. These
would be largely replaced by op-amps made with MOSFETs in the 1980s. During the 1970s
single sided supply op-amps also became available.
[edit] 1972: Single sided supply op-amps being produced
A single sided supply op-amp is one where the input and output voltages can be as low as the
negative power supply voltage instead of needing to be at least two volts above it. The result is
that it can operate in many applications with the negative supply pin on the op-amp being
connected to the signal ground, thus eliminating the need for a separate negative power supply.
The LM324 (released in 1972) was one such op-amp that came in a quad package (four separate
op-amps in one package) and became an industry standard. In addition to packaging multiple op-
amps in a single package, the 1970s also saw the birth of op-amps in hybrid packages. These op-
amps were generally improved versions of existing monolithic op-amps. As the properties of
monolithic op-amps improved, the more complex hybrid ICs were quickly relegated to systems
that are required to have extremely long service lives or other specialty systems.
[edit] Recent trends
Recently supply voltages in analog circuits have decreased (as they have in digital logic) and
low-voltage op-amps have been introduced reflecting this. Supplies of ±5 V and increasingly
3.3 V (sometimes as low as 1.8 V) are common. To maximize the signal range modern op-amps
commonly have rail-to-rail output (the ouput signal can range from the lowest supply voltage to
the highest) and sometimes rail-to-rail inputs.
[edit] Classification
Op-amps may be classified by their construction:
• discrete (built from individual transistors or tubes/valves)
• IC (fabricated in an Integrated circuit) - most common
• hybrid
IC op-amps may be classified in many ways, including:
• Military, Industrial, or Commercial grade (for example: the LM301 is the commercial
grade version of the LM101, the LM201 is the industrial version). This may define
operating temperature ranges and other environmental or quality factors.
 • Classification by package type may also affect environmental hardiness, as well as
manufacturing options; DIP, and other through-hole packages are tending to be replaced
by Surface-mount devices.
• Classification by internal compensation: op-amps may suffer from high frequency
instability in some negative feedback circuits unless a small compensation capacitor
modifies the phase- and frequency- responses; op-amps with capacitor built in are termed
"compensated", or perhaps compensated for closed-loop gains down to (say) 5, others:
uncompensated.
• Single, dual and quad versions of many commercial op-amp IC are available, meaning 1,
2 or 4 operational amplifiers are included in the same package.
• Rail-to-rail input (and/or output) op-amps can work with input (and/or output) signals
very close to the power supply rails.
• CMOS op-amps (such as the CA3140E) provide extremely high input resistances, higher
than JFET-input op-amps, which are normally higher than bipolar-input op-amps.
• other varieties of op-amp include programmable op-amps (simply meaning the quiescent
current, gain, bandwidth and so on can be adjusted slightly by an external resistor).
• manufacturers often tabulate their op-amps according to purpose, such as low-noise pre-
amplifiers, wide bandwidth amplifiers, and so on.
[edit] Applications

DIP pinout for 741-type operational amplifier

Main article: Operational amplifier applications
[edit] Use in electronics system design
The use of op-amps as circuit blocks is much easier and clearer than specifying all their
individual circuit elements (transistors, resistors, etc.), whether the amplifiers used are integrated
or discrete. In the first approximation op-amps can be used as if they were ideal differential gain
blocks; at a later stage limits can be placed on the acceptable range of parameters for each op-
amp.
Circuit design follows the same lines for all electronic circuits. A specification is drawn up
governing what the circuit is required to do, with allowable limits. For example, the gain may be
required to be 100 times, with a tolerance of 5% but drift of less than 1% in a specified
temperature range; the input impedance not less than one megohm; etc.
A basic circuit is designed, often with the help of circuit modeling (on a computer). Specific
commercially available op-amps and other components are then chosen that meet the design
criteria within the specified tolerances at acceptable cost. If not all criteria can be met, the
specification may need to be modified.
A prototype is then built and tested; changes to meet or improve the specification, alter
functionality, or reduce the cost, may be made.
[edit] Basic single stage amplifiers
[edit] Non-inverting amplifier

An op-amp connected in the non-inverting amplifier configuration

In a non-inverting amplifier, the output voltage changes in the same direction as the input
voltage.
The gain equation for the op-amp is:

However, in this circuit V– is a function of Vout because of the negative feedback through the R1R2
network. R1 and R2 form a voltage divider, and as V– is a high-impedance input, it does not load it
appreciably. Consequently:

where

Substituting this into the gain equation, we obtain:

Solving for Vout:

If AOL is very large, this simplifies to

.
[edit] Inverting amplifier
An op-amp connected in the inverting amplifier configuration
In an inverting amplifier, the output voltage changes in an opposite direction to the input
voltage.
As with the non-inverting amplifier, we start with the gain equation of the op-amp:

This time, V– is a function of both Vout and Vin due to the voltage divider formed by Rf and Rin.
Again, the op-amp input does not apply an appreciable load, so:

Substituting this into the gain equation and solving for Vout:

If AOL is very large, this simplifies to

.
A resistor is often inserted between the non-inverting input and ground (so both inputs "see"
similar resistances), reducing the input offset voltage due to different voltage drops due to bias
current, and may reduce distortion in some op-amps.
A DC-blocking capacitor may be inserted in series with the input resistor when a frequency
response down to DC is not needed and any DC voltage on the input is unwanted. That is, the
capacitive component of the input impedance inserts a DC zero and a low-frequency pole that
gives the circuit a bandpass or high-pass characteristic.
The potentials at the operational amplifier inputs remain virtually constant (near ground) in the
inverting configuration. The constant operating potential typically results in distortion levels that
are lower than those attainable with the non-inverting topology.
[edit] Positive feedback configurations
Another typical configuration of op-amps is with positive feedback, which takes a fraction of the
output signal back to the non-inverting input. An important application of it is the comparator
with hysteresis, the Schmitt trigger.
[edit] Positive voltage level detector
A positive reference voltage Vref is applied to one of the op-amp's inputs. This means that the op-
amp is set up as a comparator to detect a positive voltage. If the voltage to be sensed, Ei, is
applied to op amp's (+) input, the result is a noninverting positive-level detector. When Ei is
above Vref, VO equals +Vsat. When Ei is below Vref, VO equals -Vsat.
If Ei, is applied to the inverting input, the circuit is an inverting positive-level detector: When Ei
is above Vref, VO equals -Vsat.
[edit] Negative voltage level detector
A negative voltage detector is a circuit that detects when input signal Ei crosses the negative
voltage -Vref. When Ei is above -Vref, VO equals +Vsat. When Eiis below -Vref, VO equals
-Vsat.When Ei is above -Vref, VO equals -Vsat, and when Eiis below -Vref, VO equals +Vsat.
[edit] Sine to square wave converter
The zero detector will convert the output of a sine-wave from a function generator into a
variable-frequency square wave. If Ei is a sine wave, triangular wave, or wave of any other shape
that is symmetrical around zero, the zero-crossing detector's output will be square.
Because of the wide slew-range and lack of positive feedback, the response of all the level
detectors described above will be relatively slow. Using a general-purpose op-amp, for example,
the frequency of Ei for the sine to square wave converter should probably be below 100 Hz.[citation
needed]

[edit] Other applications

• audio- and video-frequency pre-amplifiers and buffers
• voltage comparators
• differential amplifiers
• differentiators and integrators
• filters
• precision rectifiers
• precision peak detectors
• voltage and current regulators
• analog calculators
• analog-to-digital converters
• digital-to-analog converter
• voltage clamps
• oscillators and waveform generators
Most single, dual and quad op-amps available have a standardized pin-out which permits one
type to be substituted for another without wiring changes. A specific op-amp may be chosen for
its open loop gain, bandwidth, noise performance, input impedance, power consumption, or a
compromise between any of these factors.
[edit] Limitations of real op-amps
Real op-amps differ from the ideal model in various respects.
IC op-amps as implemented in practice are moderately complex integrated circuits; see the
internal circuitry for the relatively simple 741 op-amp below, for example.
[edit] DC imperfections
Real operational amplifiers suffer from several non-ideal effects:
Finite gain
Open-loop gain is infinite in the ideal operational amplifier but finite in real operational
amplifiers. Typical devices exhibit open-loop DC gain ranging from 100,000 to over 1
million. So long as the loop gain (i.e., the product of open-loop and feedback gains) is
very large, the circuit gain will be determined entirely by the amount of negative
feedback (i.e., it will be independent of open-loop gain). In cases where closed-loop gain
must be very high, the feedback gain will be very low, and the low feedback gain causes
low loop gain; in these cases, the operational amplifier will cease to behave ideally.
Finite input impedances
The differential input impedance of the operational amplifier is defined as the impedance
between its two inputs; the common-mode input impedance is the impedance from each
input to ground. MOSFET-input operational amplifiers often have protection circuits that
effectively short circuit any input differences greater than a small threshold, so the input
impedance can appear to be very low in some tests. However, as long as these operational
amplifiers are used in a typical high-gain negative feedback application, these protection
circuits will be inactive. The input bias and leakage currents described below are a more
important design parameter for typical operational amplifier applications.
Non-zero output impedance
Low output impedance is important for low-impedance loads; for these loads, the voltage
drop across the output impedance of the amplifier will be significant. Hence, the output
impedance of the amplifier limits the maximum power that can be provided. In a
negative-feedback configuration, the output impedance of the amplifier is effectively
lowered; thus, in linear applications, op-amps usually exhibit a very low output
impedance indeed. Negative feedback can not, however, reduce the limitations that Rload
in conjunction with Rout place on the maximum and minimum possible output voltages; it
can only reduce output errors within that range.
Low-impedance outputs typically require high quiescent (i.e., idle) current in the output
stage and will dissipate more power, so low-power designs may purposely sacrifice low
output impedance.
Input current
Due to biasing requirements or leakage, a small amount of current (typically ~10
nanoamperes for bipolar op-amps, tens of picoamperes for JFET input stages, and only a
few pA for MOSFET input stages) flows into the inputs. When large resistors or sources
with high output impedances are used in the circuit, these small currents can produce
large unmodeled voltage drops. If the input currents are matched, and the impedance
looking out of both inputs are matched, then the voltages produced at each input will be
equal. Because the operational amplifier operates on the difference between its inputs,
 these matched voltages will have no effect (unless the operational amplifier has poor
CMRR, which is described below). It is more common for the input currents (or the
impedances looking out of each input) to be slightly mismatched, and so a small offset
voltage can be produced. This offset voltage can create offsets or drifting in the
operational amplifier. It can often be nulled externally; however, many operational
amplifiers include offset null or balance pins and some procedure for using them to
remove this offset. Some operational amplifiers attempt to nullify this offset
automatically.
Input offset voltage
This voltage, which is what is required across the op-amp's input terminals to drive the
output voltage to zero,[8][nb 1] is related to the mismatches in input bias current. In the
perfect amplifier, there would be no input offset voltage. However, it exists in actual op-
amps because of imperfections in the differential amplifier that constitutes the input stage
of the vast majority of these devices. Input offset voltage creates two problems: First, due
to the amplifier's high voltage gain, it virtually assures that the amplifier output will go
into saturation if it is operated without negative feedback, even when the input terminals
are wired together. Second, in a closed loop, negative feedback configuration, the input
offset voltage is amplified along with the signal and this may pose a problem if high
precision DC amplification is required or if the input signal is very small.[nb 2]
Common mode gain
A perfect operational amplifier amplifies only the voltage difference between its two
inputs, completely rejecting all voltages that are common to both. However, the
differential input stage of an operational amplifier is never perfect, leading to the
amplification of these identical voltages to some degree. The standard measure of this
defect is called the common-mode rejection ratio (denoted CMRR). Minimization of
common mode gain is usually important in non-inverting amplifiers (described below)
that operate at high amplification.
Temperature effects
All parameters change with temperature. Temperature drift of the input offset voltage is
especially important.
Power-supply rejection
The output of a perfect operational amplifier will be completely independent from ripples
that arrive on its power supply inputs. Every real operational amplifier has a specified
power supply rejection ratio (PSRR) that reflects how well the op-amp can reject changes
in its supply voltage. Copious use of bypass capacitors can improve the PSRR of many
devices, including the operational amplifier.
Drift
Real op-amp parameters are subject to slow change over time and with changes in
temperature, input conditions, etc.
Noise
Amplifiers generate random voltage at the output even when there is no signal applied.
This can be due to thermal noise and flicker noise of the devices. For applications with
high gain or high bandwidth, noise becomes a very important consideration.
[edit] AC imperfections
The op-amp gain calculated at DC does not apply at higher frequencies. To a first approximation,
the gain of a typical op-amp is inversely proportional to frequency. This means that an op-amp is
characterized by its gain-bandwidth product. For example, an op-amp with a gain bandwidth
product of 1 MHz would have a gain of 5 at 200 kHz, and a gain of 1 at 1 MHz. This low-pass
characteristic is introduced deliberately, because it tends to stabilize the circuit by introducing a
dominant pole. This is known as frequency compensation.
Typical low cost, general purpose op-amps exhibit a gain bandwidth product of a few megahertz.
Specialty and high speed op-amps can achieve gain bandwidth products of hundreds of
megahertz. For very high-frequency circuits, a completely different form of op-amp called the
current-feedback operational amplifier is often used.
Other imperfections include:
Finite bandwidth
All amplifiers have a finite bandwidth. This creates several problems for op amps. First,
associated with the bandwidth limitation is a phase difference between the input signal
and the amplifier output that can lead to oscillation in some feedback circuits. The
internal frequency compensation used in some op amps to increase the gain or phase
margin intentionally reduces the bandwidth even further to maintain output stability when
using a wide variety of feedback networks. Second, reduced bandwidth results in lower
amounts of feedback at higher frequencies, producing higher distortion, noise, and output
impedance and also reduced output phase linearity as the frequency increases.
Input capacitance
Most important for high frequency operation because it further reduces the open loop
bandwidth of the amplifier.
Common mode gain
See DC imperfections, above.
[edit] Non-linear imperfections
Saturation
output voltage is limited to a minimum and maximum value close to the power supply
voltages.[nb 3] Saturation occurs when the output of the amplifier reaches this value and is
usually due to:
• In the case of an op-amp using a bipolar power supply, a voltage gain that
produces an output that is more positive or more negative than that maximum or
minimum; or
• In the case of an op-amp using a single supply voltage, either a voltage gain that
produces an output that is more positive than that maximum, or a signal so close
to ground that the amplifier's gain is not sufficient to raise it above the lower
threshold.[nb 4]
Slewing
the amplifier's output voltage reaches its maximum rate of change. Measured as the slew
rate, it is usually specified in volts per microsecond. When slewing occurs, further
increases in the input signal have no effect on the rate of change of the output. Slewing is
usually caused by internal capacitances in the amplifier, especially those used to
implement its frequency compensation.
Non-linear input-output relationship
The output voltage may not be accurately proportional to the difference between the input
voltages. It is commonly called distortion when the input signal is a waveform. This
effect will be very small in a practical circuit if substantial negative feedback is used.
[edit] Power considerations
Limited output current
The output current must be finite. In practice, most op-amps are designed to limit the
output current so as not to exceed a specified level — around 25 mA for a type 741 IC
op-amp — thus protecting the op-amp and associated circuitry from damage. Modern
designs are electronically more rugged than earlier implementations and some can sustain
direct short circuits on their outputs without damage.
Limited dissipated power
The output current flows through the op-amp's internal output impedance, dissipating
heat. If the op-amp dissipates too much power, then its temperature will increase above
some safe limit. The op-amp may enter thermal shutdown, or it may be destroyed.
Modern integrated FET or MOSFET op-amps approximate more closely the ideal op-amp than
bipolar ICs when it comes to input impedance and input bias and offset currents. Bipolars are
generally better when it comes to input voltage offset, and often have lower noise. Generally, at
room temperature, with a fairly large signal, and limited bandwidth, FET and MOSFET op-amps
now offer better performance.
[edit] Internal circuitry of 741 type op-amp
Though designs vary between products and manufacturers, all op-amps have basically the same
internal structure, which consists of three stages:

A component level diagram of the common 741 op-amp. Dotted lines outline: current mirrors
(red); differential amplifier (blue); class A gain stage (magenta); voltage level shifter (green);
output stage (cyan).
1. Differential amplifier – provides low noise amplification, high input impedance, usually a
differential output.
2. Voltage amplifier – provides high voltage gain, a single-pole frequency roll-off, usually
single-ended output.
 3. Output amplifier – provides high current driving capability, low output impedance,
current limiting and short circuit protection circuitry.
[edit] Input stage
[edit] Constant-current stabilization system
The input stage DC conditions are stabilized by a high-gain negative feedback system whose
main parts are the two current mirrors on the left of the figure, outlined in red. The main purpose
of this negative feedback system—to supply the differential input stage with a stable constant
current—is realized as follows.
The current through the 39 kΩ resistor acts as a current reference for the other bias currents used
in the chip. The voltage across the resistor is equal to the voltage across the supply rails (

) minus two transistor diode drops (i.e., from Q11 and Q12), and so the current has

value . The Widlar current mirror built by Q10, Q11,

and the 5 kΩ resistor produces a very small fraction of Iref at the Q10 collector. This small
constant current through Q10's collector supplies the base currents for Q3 and Q4 as well as the
Q9 collector current. The Q8/Q9 current mirror tries to make Q9's collector current the same as
the Q3 and Q4 collector currents. Thus Q3 and Q4's combined base currents (which are of the
same order as the overall chip's input currents) will be a small fraction of the already small Q10
current.
So, if the input stage current increases for any reason, the Q8/Q9 current mirror will draw current
away from the bases of Q3 and Q4, which reduces the input stage current, and vice versa. The
feedback loop also isolates the rest of the circuit from common-mode signals by making the base
voltage of Q3/Q4 follow tightly 2Vbe below the higher of the two input voltages.
[edit] Differential amplifier
The blue outlined section is a differential amplifier. Q1 and Q2 are input emitter followers and
together with the common base pair Q3 and Q4 form the differential input stage. In addition, Q3
and Q4 also act as level shifters and provide voltage gain to drive the class A amplifier. They
also help to increase the reverse Vbe rating on the input transistors (the emitter-base junctions of
the NPN transistors Q1 and Q2 break down at around 7 V but the PNP transistors Q3 and Q4
have breakdown voltages around 50 V).[9]
The differential amplifier formed by Q1–Q4 drives a current mirror active load formed by
transistors Q5–Q7 (actually, Q6 is the very active load). Q7 increases the accuracy of the current
mirror by decreasing the amount of signal current required from Q3 to drive the bases of Q5 and
Q6. This configuration provides differential to single ended conversion as follows:
The signal current of Q3 is the input to the current mirror while the output of the mirror (the
collector of Q6) is connected to the collector of Q4. Here, the signal currents of Q3 and Q4 are
summed. For differential input signals, the signal currents of Q3 and Q4 are equal and opposite.
Thus, the sum is twice the individual signal currents. This completes the differential to single
ended conversion.
The open circuit signal voltage appearing at this point is given by the product of the summed
signal currents and the paralleled collector resistances of Q4 and Q6. Since the collectors of Q4
and Q6 appear as high resistances to the signal current, the open circuit voltage gain of this stage
is very high.
The base current at the inputs is not zero and the effective (differential) input impedance of a 741
is about 2 MΩ. The "offset null" pins may be used to place external resistors in parallel with the
two 1 kΩ resistors (typically in the form of the two ends of a potentiometer) to adjust the
balancing of the Q5/Q6 current mirror and thus indirectly control the output of the op-amp when
zero signal is applied between the inputs.
[edit] Class A gain stage
The section outlined in magenta is the class A gain stage. The top-right current mirror Q12/Q13
supplies this stage by a constant current load, via the collector of Q13, that is largely independent
of the output voltage. The stage consists of two NPN transistors in a Darlington configuration
and uses the output side of a current mirror as its collector load to achieve high gain. The 30 pF
capacitor provides frequency selective negative feedback around the class A gain stage as a
means of frequency compensation to stabilise the amplifier in feedback configurations. This
technique is called Miller compensation and functions in a similar manner to an op-amp
integrator circuit. It is also known as 'dominant pole compensation' because it introduces a
dominant pole (one which masks the effects of other poles) into the open loop frequency
response. This pole can be as low as 10 Hz in a 741 amplifier and it introduces a −3 dB loss into
the open loop response at this frequency. This internal compensation is provided to achieve
unconditional stability of the amplifier in negative feedback configurations where the feedback
network is non-reactive and the closed loop gain is unity or higher. Hence, the use of the
operational amplifier is simplified because no external compensation is required for unity gain
stability; amplifiers without this internal compensation may require external compensation or
closed loop gains significantly higher than unity.
[edit] Output bias circuitry
The green outlined section (based on Q16) is a voltage level shifter or rubber diode (i.e., a VBE
multiplier); a type of voltage source. In the circuit as shown, Q16 provides a constant voltage
drop between its collector and emitter regardless of the current through the circuit. If the base
current to the transistor is assumed to be zero, and the voltage between base and emitter (and
across the 7.5 kΩ resistor) is 0.625 V (a typical value for a BJT in the active region), then the
current through the 4.5 kΩ resistor will be the same as that through the 7.5 kΩ, and will produce
a voltage of 0.375 V across it. This keeps the voltage across the transistor, and the two resistors
at 0.625 + 0.375 = 1 V. This serves to bias the two output transistors slightly into conduction
reducing crossover distortion. In some discrete component amplifiers this function is achieved
with (usually two) silicon diodes.
[edit] Output stage
The output stage (outlined in cyan) is a Class AB push-pull emitter follower (Q14, Q20)
amplifier with the bias set by the Vbe multiplier voltage source Q16 and its base resistors. This
stage is effectively driven by the collectors of Q13 and Q19. Variations in the bias with
temperature, or between parts with the same type number, are common so crossover distortion
and quiescent current may be subject to significant variation. The output range of the amplifier is
about one volt less than the supply voltage, owing in part to Vbe of the output transistors Q14 and
Q20.
The 25 Ω resistor in the output stage acts as a current sense to provide the output current-limiting
function which limits the current in the emitter follower Q14 to about 25 mA for the 741. Current
limiting for the negative output is done by sensing the voltage across Q19's emitter resistor and
using this to reduce the drive into Q15's base. Later versions of this amplifier schematic may
show a slightly different method of output current limiting. The output resistance is not zero, as it
would be in an ideal op-amp, but with negative feedback it approaches zero at low frequencies.
Note: while the 741 was historically used in audio and other sensitive equipment, such use is
now rare because of the improved noise performance of more modern op-amps. Apart from
generating noticeable hiss, 741s and other older op-amps may have poor common-mode
rejection ratios and so will often introduce cable-borne mains hum and other common-mode
interference, such as switch 'clicks', into sensitive equipment.
The "741" has come to often mean a generic op-amp IC (such as uA741, LM301, 558, LM324,
TBA221 - or a more modern replacement such as the TL071). The description of the 741 output
stage is qualitatively similar for many other designs (that may have quite different input stages),
except:
• Some devices (uA748, LM301, LM308) are not internally compensated (require an
external capacitor from output to some point within the operational amplifier, if used in
low closed-loop gain applications).
• Some modern devices have rail-to-rail output capability (output can be taken to positive
or negative power supply rail within a few millivolts).
[edit] See also
Electronics portal

• Operational amplifier applications

• Differential amplifier
• Instrumentation amplifier
• Active filter
• Current-feedback operational amplifier
• Operational transconductance amplifier
• George A. Philbrick
• Analog computer
• Negative feedback amplifier
[edit] Notes
1. ^ This definition hews to the convention of measuring op-amp parameters with respect to
the zero voltage point in the circuit, which is usually half the total voltage between the
amplifier's positive and negative power rails.
2. ^ Many older designs of operational amplifiers have offset null inputs to allow the offset
to be manually adjusted away. Modern precision op-amps can have internal circuits that
automatically cancel this offset using choppers or other circuits that measure the offset
voltage periodically and subtract it from the input voltage.
3. ^ That the output cannot reach the power supply voltages is usually the result of
limitations of the amplifier's output stage transistors. See "Output stage," below.
 4. ^ The output of older op-amps can reach to within one or two volts of the supply rails.
The output of newer so-called "rail to rail" op-amps can reach to within millivolts of the
supply rails when providing low output currents.
[edit] References
1. ^ MAXIM Application Note 1108: Understanding Single-Ended, Pseudo-Differential and
Fully-Differential ADC Inputs — Retrieved November 10, 2007
2. ^ Analog devices MT-044 TUTORIAL
3. ^ a b Horowitz, Paul; Hill, Winfield (1989). The Art of Electronics. Cambridge, UK:
Cambridge University Press. ISBN 0521370957. http://books.google.com/books?
id=bkOMDgwFA28C&pg=PA177&lpg=PA177#v=onepage&q&f=false.
4. ^ Jung, Walter G. (2004). "Chapter 8: Op Amp History". Op Amp Applications
Handbook. Newnes. p. 777. ISBN 9780750678445. http://books.google.com/books?
id=dunqt1rt4sAC. Retrieved 2008-11-15.
5. ^ Jung, Walter G. (2004). "Chapter 8: Op Amp History". Op Amp Applications
Handbook. Newnes. p. 779. ISBN 9780750678445. http://books.google.com/books?
id=dunqt1rt4sAC. Retrieved 2008-11-15.
6. ^ http://www.analog.com/library/analogDialogue/archives/39-05/Web_ChH_final.pdf
7. ^ A.P. Malvino, Electronic Principles (2nd Ed. 1979. ISBN 0-07-039867-4) p. 476.
8. ^ D.F. Stout Handbook of Operational Amplifier Circuit Design (McGraw-Hill, 1976,
ISBN 007061797X ) pp. 1–11.
9. ^ The uA741 Operational Amplifier

[edit] Further reading

• Basic Operational Amplifiers and Linear Integrated Circuits; 2nd Ed; Thomas L Floyd;
593 pages; 1998; ISBN 9780130829870.
• Design with Operational Amplifiers and Analog Integrated Circuits; 3rd Ed; Sergio
Franco; 672 pages; 2001; ISBN 9780072320848.
• Operational Amplifiers and Linear Integrated Circuits; 6th Ed; Robert F Coughlin; 529
pages; 2000; ISBN 9780130149916.
• Op-Amps and Linear Integrated Circuits; 4th Ed; Ram Gayakwad; 543 pages; 1999;
ISBN 9780132808682.
[edit] External links
Wikimedia Commons has media related to: Operational amplifiers

Wikiversity has learning materials about Operational amplifier

 The Wikibook Electronics has a page on the topic of
Op-Amps

• Introduction to op-amp circuit stages, second order filters, single op-amp bandpass filters,
and a simple intercom
• Hyperphysics – descriptions of common applications
• Single supply op-amp circuit collection
• Op-amp circuit collection
• Opamps for everyone Downloadable book.
• MOS op amp design: A tutorial overview
• High Speed OpAmp Techniques very practical and readable - with photos and real
waveforms
• Op Amp Applications Downloadable book. Can also be bought
• Operational Amplifier Noise Prediction (All Op Amps) using spot noise
• Operational Amplifier Basics
• History of the Op-amp from vacuum tubes to about 2002. Lots of detail, with schematics.
IC part is somewhat ADI-centric.
• IC Op-Amps Through the Ages
• ECE 209: Operational amplifier basics – Brief document explaining zero error by naive
high-gain negative feedback. Gives single OpAmp example that generalizes typical
configurations.
• Loebe Julie historical OpAmp interview by Bob Pease
• www.PhilbrickArchive.org - A free repository of materials from George A Philbrick /
Researches - Operational Amplifier Pioneer
Retrieved from "http://en.wikipedia.org/wiki/Operational_amplifier"
Categories: Electronic amplifiers | Linear integrated circuits
Hidden categories: All articles with unsourced statements | Articles with unsourced statements
from January 2009 | Articles with unsourced statements from February 2011
Personal tools
• Log in / create account
Namespaces
• Article
• Discussion
Variants
Views
• Read
• Edit
• View history
Actions
Search
Top of Form
Special:Search

Bottom of Form
Navigation
• Main page
• Contents
• Featured content
• Current events
• Random article
• Donate to Wikipedia
Interaction
• Help
• About Wikipedia
• Community portal
• Recent changes
• Contact Wikipedia
Toolbox
• What links here
• Related changes
• Upload file
• Special pages
• Permanent link
• Cite this page
Print/export
• Create a book
• Download as PDF
• Printable version
Languages
• ‫العربية‬
• Български
• Català
• Česky
• Dansk
• Deutsch
• Español
• Esperanto
• Euskara
• ‫فارسی‬
• Français
• Galego
• 한국어
• िहनदी
• Hrvatski
• Bahasa Indonesia
• Italiano
• ‫עברית‬
• Lietuvių
• Magyar
• മലയാളം
• Nederlands
• 日本語
• Norsk (bokmål)
• Norsk (nynorsk)
• Polski
• Português
• Русский
• Slovenčina
• Slovenščina
• Српски / Srpski
• Suomi
• Svenska
• தமிழ்
• Türkçe
• ᨅᨔ ᨕᨘᨁᨗ
• Українська
• Tiếng Việt
• 中文
• This page was last modified on 30 March 2011 at 16:04.
• Text is available under the Creative Commons Attribution-ShareAlike License;
additional terms may apply. See Terms of Use for details.
Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-profit
organization.
• Contact us
• Privacy policy
• About Wikipedia
• Disclaimers