Scribd
Upload
74 views

1 - DDA Line Drawing Algorithm

The DDA (Digital Differential Analyzer) algorithm is an incremental scan conversion method used to draw lines on a raster display. It works by taking unit steps along the coordinate axis with the greatest change between the line's endpoints, and calculating the corresponding values along the other axis. This avoids floating point multiplications and is faster than using the line equation directly. The algorithm handles two cases based on whether the slope is less than or greater than one.

Uploaded by

BEKAN FAYERA
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
74 views

1 - DDA Line Drawing Algorithm

The DDA (Digital Differential Analyzer) algorithm is an incremental scan conversion method used to draw lines on a raster display. It works by taking unit steps along the coordinate axis with the greatest change between the line's endpoints, and calculating the corresponding values along the other axis. This avoids floating point multiplications and is faster than using the line equation directly. The algorithm handles two cases based on whether the slope is less than or greater than one.

Uploaded by

BEKAN FAYERA
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

DDA LINE DRAWING ALGORITHM

DDA algorithm is an incremental scan conversion method. Here we perform


calculations at each step using the results from the preceding step. The characteristic of
the DDA algorithm is to take unit steps along one coordinate and compute the
corresponding values along the other coordinate. The unit steps are always along the
coordinate of greatest change, e.g. if dx = 10 and dy = 5, then we would take unit steps
along x and compute the steps along y.

 Suppose at step i we have calculated (xi, yi) to be a point on the line. Since the next
point (x i+1,y i+1) should satisfy ?y/? x =m where ?y= y i+1–yi and ? x= x i+1–xi , we
have y i+1= yi + m? x or x i+1=xi+ ? y/m

 These formulas are used in DDA algorithm as follows. When |m| ? 1, we start with x =
x1’? (assuming that x1’ <x2’) and y = y1’, and set ? x =1( i.e., unit increment in the x
direction). The y coordinate of each successive point on the line is calculated using y
i+1= yi + m.

When |m| >1, we start with x= x1’ and y= y1’ (assuming that y1’ < y2’), set ? y =1 ( i.e.,
unit increment in the y direction). The x coordinate of each successive point on the line
is calculated using x i+1=xi+ 1/m. This process continues until x reaches x2’(for m| ? 1
case )or y reaches y2’ (for m| > 1 case ) and all points are scan converted to pixel points.

The explanation is as follows: In DDA algorithm we have to find the new point xi+1 and
yi+1 from the existing points xi and yi. As a first step here we identify the major axis and
the minor axis of the line to be drawn. Once the major axis is found we sample the major
axis at unit intervals and find the value in the other axis by using the slope equation of
the line.

For example if the end points of the line is given as (x1,y1)= (2,2) and (x2, y2)= (9,5).
Here we will calculate y2-y1 and x2-x1 to find which one is greater. Here y2-y1 =3 and
x2-x1 =7; therefore here the major axis is the x axis. So here we need to sample the x axis
at unit intervals i.e.? x = 1 and we will find out the y values for each ? x in the x axis
using the slope equation.

 In DDA we need to consider two cases; one is slope of the line less than or equal to one
(|m| ? 1)and slope of the line greater than one (m| > 1). When |m| ? 1 means y2-y1 = x2-
x1 or y2-y1 <x2-x1.In both these cases we assume x to be the major axis. Therefore we
sample x axis at unit intervals and find the y values corresponding to each x value.

We have the slope equation as

?y=m?x

           y2-y1 = m (x2-x1)

In general terms we can say that y i+1 - yi = m(x i+1 - xi ). But here ? x = 1; therefore the
equation reduces to y i+1= yi + m = yi + dy/dx.

When m| > 1 means y2-y1> x2-x1 and therefore we assume y to be the major axis. Here

we sample y axis at unit intervals and find the x values corresponding to each y value.
We have the slope equation as

?y=m?x

y2-y1 = m (x2-x1)

In general terms we can say that y i+1 - yi = m(x i+1 - xi ). But here ? y = 1; therefore the
equation reduces to 1 = m(x i+1 - xi). Therefore

x i+1=xi+ 1/m

x i+1=xi+ dx/dy

DDA Algorithm is given below:

procedure DDA( x1, y1, x2, y2: integer);

var

            dx, dy, steps: integer;

            x_inc, y_inc, x, y: real;

begin

            dx := x2 - x1; dy := y2 - y1;

            if abs(dx) > abs(dy) then

            steps := abs(dx); {steps is larger of dx, dy}


else

            steps := abs(dy);

            x_inc := dx/steps; y_inc := dy/steps;

            {either x_inc or y_inc = 1.0, the other is the slope}

            x:=x1; y:=y1;

            set_pixel(round(x), round(y));

            for i := 1 to steps do

begin

             x := x + x_inc;

             y := y + y_inc;

              set_pixel(round(x), round(y));

end;

end; {DDA}

The DDA algorithm is faster than the direct use of the line equation since it calculates
points on the line without any floating point multiplication.

Advantages of DDA Algorithm

1. It is the simplest algorithm and it does not require special skills for implementation.
2. It is a faster method for calculating pixel positions than the direct use of equation y =
mx + b. It eliminates the multiplication in the equation by making use of raster
characteristics, so that appropriate increments are applied in the x or v direction to find
the pixel positions along the line path.

Disadvantages of DDA Algorithm

1. Floating point arithmetic in DDA algorithm is still time-consuming.


2. The algorithm is orientation dependent. Hence end point accuracy is poor.

You might also like