Scribd
Upload
216 views

Classification On Basis of Fabrication

Monolithic integrated circuits (ICs) are fabricated on a single chip of silicon, with all active and passive components formed at the same time using diffusion steps. This allows for identical component characteristics, making monolithic ICs cheap and reliable. An example is the operational amplifier IC741. Advantages include small size, low cost, reliability, and ability to implement complex circuits. Disadvantages include poor component isolation, inability to include inductors, and low power ratings restricting use to low-power applications.

Uploaded by

Melkamu Fekadu
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
216 views

Classification On Basis of Fabrication

Monolithic integrated circuits (ICs) are fabricated on a single chip of silicon, with all active and passive components formed at the same time using diffusion steps. This allows for identical component characteristics, making monolithic ICs cheap and reliable. An example is the operational amplifier IC741. Advantages include small size, low cost, reliability, and ability to implement complex circuits. Disadvantages include poor component isolation, inability to include inductors, and low power ratings restricting use to low-power applications.

Uploaded by

Melkamu Fekadu
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Classification on basis of Fabrication

Monolithic Integrated Circuits


As the word implies, Monolithic Integrated Circuits are manufactured or
fabricated on a single chip of Silicon. All the active and passive circuit
components are formed at the same time, using diffusion steps.

Monolithic ICs are mostly used in applications where identical characteristics of


components are required and hence they are cheap and highly reliable.

Example of Monolithic IC
A classic example of a Monolithic IC is the operational amplifier IC741. It is an 8-
pin IC, first developed by Fairchild Semiconductors, and later by companies like
Motorola, National Semiconductors, etc.

This IC is available in the dual in-line package, with pins 2 and 3 as Inverting and
Non-Inverting inputs respectively and 6 as output. It requires a dual power
supply, with positive supply to pin 7 and negative supply to pin 4.

Advantages of Monolithic ICs


1. Smaller in size and less weight.
2. Low cost and less production time.
3. Highly reliable, due to no soldered joints and fewer interconnections.
4. Complex circuits can be fabricated easily, thus achieving improved
functional performance.
5. As components are fabricated very close to each other, small signal
operation is possible as it eliminates any chance of stray signal pickup.
6. No external projections required as all components are fabricated inside
the chip.

Disadvantages of Monolithic ICs


1. Fabrication of components very nearer to each other also results in poor
isolation between them.
2. Inductors cannot be fabricated on a Monolithic IC.
3. Small size causes low power rating and the IC can only be used for low
power applications.
increase in current.

Advantages and Disadvantages


of Monolithic ICs

Monolithic IC
The word ‘monolithic’is derived from the Greek monos, meaning ‘single’and lithos, meaning
‘stone’. Thus monolithic circuit is built into a single stone or single crystal i.e. in monolithic ICs,
all circuit components, (both active and passive) and their interconnections are formed into or on
the top of a single chip or silicon as shown in fig. 1 (a) and (b).

Fig 1 (a) : Monolithic IC in Can-Type Enclosure


Fig 1 (b): Monolithic IC in Plastic Package

Advantages of Monolithic ICs


1. Miniature in size. Since  the active and passive components  are integrated on to a silicon chip
using fabrication process , the IC becomes a lot smaller. When compared to a   discrete circuit, it
may be at least a thousand times smaller.
2. Due to small size, the weight of the IC also reduces, when compared to the discrete circuit.
3. For the production of hundreds of IC’s the cost of production is very low and less time
consuming. However,  to produce hundreds of discrete circuits on a PCB for  the same logic takes
more time and increase the cost factor.
4. The PCB consisting soldered joints will be less reliable. This problem is omitted in IC’s because of
no soldered joints, with fewer interconnections, and thus highly reliable.
5. The small size of IC’s causes lesser power consumption and lesser power loss.
6.  In a discrete circuitry, if a single transistor becomes faulty, the whole circuit may fail to work.
This transistor has to be desoldered and replaced. It is difficult to find out which component has
failed. This problem can be omitted in an IC by replacing an entire IC as it is low in cost.
7.  Increased operating speed because of absence of parasitic capacitance effect.
8. As the IC’s are produced in bulk the temperature coefficients and other parameters will be
closely matching.
9.  Improved functional performance as more complex circuits can be fabricated for achieving
better characteristics.
10. All IC’s are tested for operating ranges in very low and very high temperatures.
11. As all the components are fabricated very close to each other in an IC, they are highly suitable
for small signal operation, as there won’t be any stray electrical pickup.
12. As all the components are fabricated inside the chip, there will not be any external projections.
Since their invention, manufacturers have been manufacturing monolithic ICs to carry out all
types of functions. Commercially available ICs of this type can be used as amplifiers, voltage
regulators, crowbars, AM receivers, TV circuits and computer circuits.

Disadvantages of Monolithic ICs


However, the monolithic circuits have the following limitations or drawbacks:
1. Low power rating. Since monolithic ICs are of about the size of a discrete small signal transistor,
they typically have a maximum power rating of less than 1 watt. This limits their use to low-power
applications.
2. Poorer isolation between components.
3. No possibility of fabrication of inductors.
4. Small range of values of passive components used in the ICs.
5. Lack of flexibility in circuit design as for making any variation in the circuit, a new set of masks is
required.
 

You might also like