0% found this document useful (0 votes)

136 views

Service Manual, Rev. N: Kodak Dryview 8300 Laser Imager

This service manual provides information for servicing the Kodak DryView 8300 LASER IMAGER. It contains 9 sections covering specifications, installation, adjustments, disassembly/reassembly, additional information, theory of operation, troubleshooting, illustrated parts breakdown, and diagrams. The manual includes warnings about the hazardous voltage used in the device and laser radiation safety. It provides compliance information for various regulatory agencies.

Uploaded by

edgar Bilbao Rocha

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

136 views

Service Manual, Rev. N: Kodak Dryview 8300 Laser Imager

Uploaded by

edgar Bilbao Rocha

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 284

Return to CD-ROM Collection Menu

Kodak DryView 8300 LASER IMAGER

SERVICE MANUAL, Rev. N

Revision History
Warnings and Cautions
Agency, Regulatory, and CE Marking Compliance
Section 1 – Specifications
Section 2 – Installation
Section 3 – Adjustments
Section 4 – Disassembly/Reassembly
Section 5 – Additional Information
Section 6 – Theory of Operation
Section 7 – Troubleshooting
Section 8 – Illustrated Parts Breakdown
190-8110
78-6970-7393-6 Section 9 – Diagrams
Revision History
The original issue and revisions of this Service Manual for the Kodak DryView 8300 LASER IMAGER are
identified as follows:
Issue Date (Rev. A): 12/96, Rev. B: 3/97, Rev. C: 5/97, Rev. D: 8/97, Rev. E: 10/97, Rev. F: 3/98, Rev.
G: 8/98, Rev. H: 4/99, Rev. J: 10/99, Rev. K: 3/00, Rev. L: 8/00, Rev. M: 3/01, Rev. N: 9/01.
The current Section by Section revision configuration of the manual is as follows:

Section Text Pages Changed in

Rev. Current Revision (N)
Title/a N Title and a pages
Warnings M –
TOC M –
1 M –
2 M –
3 K –
4 M –
5 N 5-2, -25, -26, -27
6 M –
7 M –
8 N 8-6, -7, -9, -12, -13
9 M –
Warnings and Cautions

Warnings and Cautions

Read and understand all instructions before using.

! WARNING
This equipment is operated with hazardous voltage which can shock, burn, or cause
death.
Remove wall plug before servicing equipment. Never pull on cord to remove from outlet. Grasp plug and
pull to disconnect.
Do not operate equipment with a damaged power cord.
Do not use an extension cord to power this equipment.
Use only the power cord supplied with the equipment.
Position the power cord so it will not be tripped over or pulled.
Connect this equipment to a grounded outlet.
Do not place a portable multiple socket outlet (power strip) on the floor. Mount the power strip on a wall or
on the underside of a table.

! WARNING
Do not use in the presence of flammable anesthetics, oxygen or nitrous oxide. This equipment does not
have a gas sealed electronics enclosure and could ignite any flammable or explosive gases present in its
environment.

! WARNING
Not protected against ingress of liquids including bodily fluids.

! WARNING
For continued protection against fire, replace fuses only with fuses of the same type and fuse rating.

! CAUTION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. Those limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

2001 March Rev. M 1908110 i

Service Manual

! CAUTION

This equipment is intended to connect to other medical devices. Installation and service maintenance are
to be performed only by qualified service personnel.

! CAUTION

Do not substitute or modify this equipment without approval of Eastman Kodak Company.

! CAUTION

U.S. Federal law restricts sale of this device to or on the order of a licensed health care practitioner.

! CAUTION

Avoid Laser Beam

This equipment employs an invisible 25 milliwatt laser. Laser radiation may be present
when the machine operates without panels or covers installed.
Use of controls or adjustments, or performance of procedures other than those specified herein, may
result in eye damage.
Covers shall be removed by authorized service personnel only.
There are no “user’ serviceable parts in this machine other than the charcoal odor filter.

! CAUTION
Avoid touching the developer drum when removing film jams from the imager. The developer drum may
become hot during extended imager operation.

D8300–134A

ii 1908110 2001 March Rev. M

Warnings and Cautions

Type B Applied Part

DANGER – Invisible Laser Radiation When Open. Part No:

Avoid Direct Exposure to Beam. Serial No:
ATTENTION – Rayonnement Laser Invisible En Cas Options:
DÕOuverture. Exposition Dangereuse 100 – 240 Volts 50 – 60 Hz 6.3 / 3.2 Amps
Au Faisceau.
CAUTION: Disconnect Power Before Servicing.
VORSICHT – Unsichtbare
.. Laserstrahlung Wenn Abdeckung
ATTENTION: Couper Le Courant Avant D’ourvir
Geoffnet. Nicht Dem Strahl Aussetzen. L’Appareillage Pour Service.
VARNING – Osynlig Laserstrlning.
.. .. Laserstrining
.. Nar ACHTUNG: Gerat Vom NetzTrennen Bevor Service.
Denna Del A Oppnad. Strlen Ar Farlig. This equipment complies with part 15 of the FCC Rules: And Radio Interference
Regulation of the Canadian Department of Communication.

Operation of this equipment in a residential area may cause unacceptable

interference to radio and television reception requiring the operator to take
whatever steps are necessary to correctÊthe interference.

This product complies with CDRH Regulation 21 CFR Subchapter J.

Class 1 laser product to IEC 825. Date of Manufacture

Laser klasse 1 produkt nach IEC 825.
Laser de cate gories 1 IEC 825.

Agency Approvals

Class 1 laser product to IEC 825.

Laser klasse 1 produkt nach IEC 825.
Laser de cate gories 1 IEC 825. Made in USA

D8300–134A

! CAUTION
General External Cleaning: This equipment may be cleaned with a damp cloth using water with mild
detergent, or commercial electronic equipment cleaner.

Classifications
UL Classified

File Number E163816

Control Number 48VF

Medical Equipment
UL 2601-1 CAN/CSA No. 601.1

!
Classified by Underwriters Laboratories Inc. With Respect to Electric Shock, Fire, Casualty and
Medical Hazards only in Accordance with UL 2601-1, CAN/CSA C22.2 No. 601.1 and IEC 601-1.

2001 March Rev. M 1908110 iii

Service Manual

BLANK PAGE

iv 1908110 2001 March Rev. M

Agency, Regulatory, and CE Marking

Agency, Regulatory, and CE Marking Compliance

All Agency, Regulatory, and CE Marking information may be found in the User Guide for this model.

2001 March Rev. M 1908110 v

Service Manual

BLANK PAGE

vi 1908110 2001 March Rev. M

Section 1 – Specifications

1-1. Dimensions
Height: 46 cm (18 in.)
Width: 46 cm (18 in.)
Depth: 66 cm (26 in.)
Weight: 56 Kg (124 lb.)

1-2. Electrical
Phase: Single
Voltage: U.S.: 100 – 120 VAC ± 10%
OUS: 100 – 240 VAC ± 10%
Frequency: 50 – 60 Hz ± 3 Hz
Current: 6.3/3.2 Amperes

1-3. Operating Environment

Temperature: 15° to 32° C (59° to 90° F)
Relative Humidity: 15% to 75% RH,
Noncondensing
Magnetic Field: ≤100 Gauss

1-4. Non-Operating Environment:

Shock/Vibration: The shipping carton must pass the standard NSTA shock/vibration test.
Temperature: The shipping carton and boxes of pouched film are capable of protecting the media from
damage (other than sensitometric change) over the temperature range –30° C for 96 hours to 65° C for 24
hours.
Humidity: The shipping carton and boxes of pouched film are capable of protecting the media from
damage (other than sensitometric change) over the humidity range 15% RH for 96 hours to 85% RH for
24 hours.

1-5. Hardware Interface (Input Modules)

• Low Resolution Analog
• High Resolution Analog
• 3M Standard Digital
• SCSI
• Network

1-6. Control Interfaces

• Control Panel
• Remote Keypad
• Host

2001 March Rev. M 1908110 1-1

Service Manual

1-7. Output
First Print
(After Ready indicator lights): 110 sec.
Subsequent Prints: 55 Prints/hr

1-8. Film Characteristics

Size: 8 x 10 in.
Cartridge Capacity: 100 Sheets

1-9. Options
• Second Input Module
• Internal Magneto/Optical Drive
• Footswitch

1-10. Memory
4-32 MB

1-2 1908110 2001 March Rev. M

Section 2 – Installation

2-1. Installation Checklist

Procedure See paragraph

j Unpack the IMAGER. 2-2
j Connect system cables and external devices. 2-3
j Apply power to the system. 2-4
j Set the installation parameters, and perform the Mark Install Date:
j For systems with Digital Input Modules. 2-5-1
j For systems with Analog Input Modules. 2-5-2
j For systems with SCSI Input Modules. 2-5-3
j For systems with Network Input Modules. 2-5-4
j Set the customer preference parameters:
j For Digital Input Modules. 2-6
j For Analog Input Modules. 2-6
j For SCSI Input Modules. 2-6
j For Network Input Modules. 2-6
j Final checkout. 2-7

2-2. Unpacking

!
Caution
The IMAGER weighs about 135 pounds. Do not attempt to lift it from the shipping box without
help. If another Kodak employee is unavailable, ask the customer’s maintenance staff to lift the
unit and set it on a cart or table.

After the IMAGER is set on a cart or table, open the accessories box and remove the power cord, cables,
and optional keypad(s) and footswitch(es).

2001 March Rev. M 1908110 2-1

Service Manual

2-3. Connecting Cables and External Devices

1. Attach the power cord.
2. If a footswitch is to be used, attach its cable to the 9–pin serial connector on the input module.
3. If a keypad is to be used:
a. Attach the keypad cable to the 9-pin serial connector on the input module, or if a foot switch is
used, attach the keypad cable to the extra connector on the footswitch cable.
b. Remove the right side cover of the imager (procedure 4-2-1). Make sure that the switch on the
input module is set (pressed in) to select ±12 V rather than RTS/CTS. (±12 V selects keypad
control.)
4. If customers want the 8300 IMAGER to acquire images using the Ultrasound Print or Remote
Acquire keys, inform them that they will have to purchase the Kodak DryView REMOTE ACQUIRE
UNIT (78-8114-2797-6) through sales.

2-3-1. For Digital Input Modules

1. Attach the data cable from the host to the 37-pin connector on the input module.
2. If host control is required (no keypad):
a. Attach the control cable from the host to the 9-pin connector on the input module.
b. Remove the right side cover of the imager (procedure 4-2-1).
c. Make sure that the switch on the input module is set (pressed) to select RTS/CTS.

2-3-2. For Analog Input Modules

1. Attach the video cable from the host to the lower BNC connector on the input module.

Note
If the modality provides an external clock, first try video acquisition without it. Use external clock only
if good video acquisition is not possible without it.

2. If the customer is using an external clock, connect the cable to the upper BNC connector.
3. If host control is required (no keypad):
a. Attach the control cable from the host to the 9-pin connector on the input module.
b. Remove the right side cover of the imager (procedure 4-2-1).
c. Make sure that the switch on the input module is set (pressed) to select RTS/CTS.

2-3-3. For SCSI Input Modules

1. Connect the SCSI device(s). (These include devices such as an external MO drive or a Bernoulli
drive.)
2. Make sure that the unit address of each device is set, and the last device in the line is terminated. If
no devices are connected to P5, internal termination should be set on via menu option (Table 2-1).
3. If there are no external devices connected to the IMAGER, P4 on the SCSI Input Module must be
terminated with an external terminator and P5 terminated internally via menu option (Table 2-1).

2-2 1908110 2001 March Rev. M

Section 2 – Installation

Table 2-1. Termination Options

2-8 1908110 2001 March Rev. M

Section 2 – Installation

Table 2-3. Setting the Analog Installation Parameters

Parameter Options Action

1. ASPECT RATIO 0.50 to 2.00 Set to an initial value of 1.0. After acquiring
a first image, changes to this value may be
necessary.
This parameter should be adjusted to what
is seen on the modality’s monitor. If a circle
or square test pattern cannot be brought up
on the monitor, have the operator make a
square or rectangle with the characters
from the unit’s keyboard.
(Note: The clocks per line parameter must
be set correctly before you attempt to set
up Aspect Ratio.)
Measure the sides of the square or
rectangle on the monitor and compare
these values to what appears on the film.
The ratio should be equivalent. A value of
.9 is typical for many Ultrasound modalities.
2. VIDEO INTERFACE
1. PIXEL CLOCK Range: 7.5 to 35 Modify or enter as required, following the
menu instructions. The number is checked
after the last digit is entered, and an audible
alarm sounds if the value is not within
range. Re-enter an acceptable value.
2. CLOCKS PER LINE 1 to 1460 Modify or enter the total pixels in a
(Same as pixels per line or horizontal line (horizontal active + horizontal
horizontal total) delay + front porch), following the menu
instructions.
3. HORIZONTAL ACTIVE 1 to 1280 Modify or enter the number of active pixels
per line following the menu instructions.
4. HORIZONTAL DELAY 1 to 512 Modify or enter the pixel number that
satisfies horizontal delay (back porch +
sync), following the menu instructions.
5. VERTICAL ACTIVE 1 to 1024 Modify or enter the required number of
vertical lines following the menu
instructions.
6. VERTICAL DELAY 1 to 500 Modify or enter the pixel number that
satisfies vertical delay (back porch),
following the menu instructions.
7. INTERLACE ON or OFF Modify or enter to indicate if video is
interlaced following the menu instructions.
Interlaced video is typical for ultrasound.
8. EXTERNAL CLOCK ON or OFF If an external clock is used, this setting
must be ON. This menu option will be
removed at a future date. Recommended
default is OFF.

2001 March Rev. M 1908110 2-9

Service Manual

Parameter Options Action

9. CLOCK DELAY Follow the menu instructions to eliminate
instances of pixel shifting at very high
frequencies (30 Mhz). This menu option will
be removed at a future date.
Video Interface (Cont.)
10. START/FRAME ODD or EVEN Follow the menu instructions to set the
correct start frame, which is typically odd.
11. PERFORM VIDEO Follow the menu instructions to
CALIBRATION automatically set the gain and offset for
printed images. If set correctly, the black in
the image area should almost match the
borders (within 0.01 to 0.03).
Note
To perform a successful video calibration, the darkest and lightest areas on the image must be
identified and selected. Some images will require cropping. Cropping can be done by selecting a
percentage of an area within the image.

The reduced image area is defined and positioned by determining start points and end points
along the X and Y axes. The start point is selected first along its X and Y axis followed by the end
point along its X and Y axis. Refer to Figure 2-1 for examples. The printout will be the full image.
Video Calibration Submenu
1. START POINT X = aa The arrow keys or numeric keypad are used
PERCENTAGE Y = bb to set the values for aa and bb within a
range of 0 to 100. Set the aa value first for
the start point on the horizontal axis. Next,
set the bb value for the start point on the
vertical axis. An audible alarm sounds if a
value is out of range. To repeat the entry
process, press CLEAR. Default is 0.
2. END POINT X = aa The arrow or numeric keys can be used to
PERCENTAGE Y = bb set the values for aa and bb within a range
of 1 to 100. Set the aa value first for the
end point on the horizontal axis. Next, set
the bb value for the end point on the vertical
axis. An audible alarm sounds if a value is
out of range. To repeat the entry process,
press CLEAR. Default is 100.
3. START To perform the video calibrate function,
CALIBRATION press ENTER. During calibration, the gas
gauge increments, then displays when
calibration is finished.

2-10 1908110 2001 March Rev. M

Section 2 – Installation

X = 20 to 90% X = 0 to 80%
Y = 20 to 80% Y = 20 to 80%

0 20 X 90 100 0 X 80 100
0 WAA 3.50 MHZ
0 WAA 3.50 MHZ
OUT 25.12% OUT 25.12%
60DB C5 E4 60DB C5 E4
FR 17 HZ FR 17 HZ
20 20

Y Y

80 80

FL = 5.5 CM FL = 5.5 CM
100 100
8300–158L

Figure 2-1.

Parameter Options Action

12. Black Level Offset 0 – 100 Leave at 0 unless darker background is
desired. At 100, a 5% darker background is
obtained.
13. White Level Offset 0 – 100 Leave at 0 unless brighter whites are
desired. At 100, 5% brighter image data is
obtained.

Note Note
After determining the correct video parameters, After determining the correct video
record them in the Service History Log. If the CPU parameters, record them in the Service
PWA is replaced in the future, these video History Log. If the CPU PWA is
parameters must be entered into the new CPU PWA. replaced in the future, these video
parameters must be entered into the
Note new CPU PWA.
If menu items 14 through 16 are selected, all video
parameters change to a scripted value. If ENTER is Note
pressed at menu item 14, items 1 through 6 change If menu items 14 through 16 are
to the parameters for the Acuson 128. selected, all video parameters change
to a scripted value. If ENTER is
pressed at menu item 14, items 1
through 6 change to the parameters for
the Acuson 128.
14. 750 X 480 If default values are desired, press ENTER.
(Acuson 128) If EXIT is pressed, no changes are made.

2001 March Rev. M 1908110 2-11

Service Manual

Parameter Options Action

15. 640 X 480 If default values are desired, press ENTER.
(ATL) If EXIT is pressed, no changes are made.

16. 580 X 480 If default values are desired, press ENTER.

(ATL) If EXIT is pressed, no changes are made.

Note
If 3M protocol is selected, options 1–4 or the Serial
Control Interface become available.
3. SERIAL CONTROL For desired settings:
INTERFACE:
1. BAUD RATE 1200, 2400, 4800, Toggle between baud rates.
9600, or 19200
2. NUMBER OF DATA BITS 7 or 8 Toggle the data bit settings for desired
value.
3. NUMBER OF STOP BITS 1 or 2 Toggle the stop bit setting for desired value.
4. PARITY ODD, EVEN, or Toggle the parity setting between
NONE selections.
5. PROTOCOL 3M or Keypad Toggle the protocol setting between
selections. (In the future, there may be
additional OEM.)
6. MARK INSTALL DATE Date of install: If date is incorrect, change Date/Time
day/month/year parameter in the General Setup Menu.

7. MEMORY MANAGEMENT A = 4.0 MB Partition memory across two input modules

B = 4.0 MB as desired. If only one module is used, all
memory is assigned to it automatically.
Refer to paragraph 5-4 for how to configure
memory.
8. CALIBRATION ENABLE ON or OFF. Leave at ON (factory default). If necessary,
enable calibration following the menu
instructions.
9. MODULE ID Input module can If desired, rename the Input Module by
be renamed for the following the instructions on the Module ID
local display. menu.
10. EXPOSURES None. Do not change. The exposure number
indicates the total film count processed by
the CPU PWA currently installed in the
IMAGER.

2-12 1908110 2001 March Rev. M

Service Manual

Table 2-7. Video Installation Parameters for NTSC C-ARM

HORIZONTAL VERTICAL VIDEO CAL

OEM MODEL AR P-C C/L HA HD VA VD X Y
FLS 14.32 908 768 123 484 16
GE E413-DSM 14.87 944 767 155 484 16
*STENOSCOP 14.75 945 730 155 588 16
DSM
*STENOSCOP 14.75 947 750 155 588 16
MDA (PC)
*STENOSCOP 29.5 945 730 155 584 18
MD10 (DR7)
OEC 902, 2000, 2500 10.32 656 526 103 484 16
7700 15.61 960 512 275 495 16
9000, 9400 10.32 656 526 103 484 16
*9600 12.91 824 640 140 480 16
DRX5 10.32 656 526 103 484 16
SPA 1000 US 10.32 656 526 103 484 16
*UROVIEW 2600 12.91 824 640 140 480 16
PHILIPS BV 25 19.17 1217 1006 182 480 14
*BV25 GOLD, 28.02 1779 1280 266 480 14
*BV26, *BV29, 26.69 1695 1280 253 480 14
*BV212
*BV 300 20.25 1292 1063 192 480 14
SIEMENS *Siremobile 2000, 13.44 848 524 226 512 36
*Compact
ZIEHM *EXPOSCOP 14.20 900 550 253 540 35
CB7-D
* = Qualified

2-28 1908110 2001 March Rev. M

Section 2 – Installation

Table 2-8. Video Installation Parameters for NTSC Nuclear Medicine

HORIZONTAL VERTICAL VIDEO CAL

OEM MODEL AR P-C C/L HA HD VA VD X Y
ADAC *PEGASUS **30.00 1415 1024 319 820 32
ELSCINT APEX 13.30 851 639 143 493 33
SP4 13.30 795 635 94 531 11
209, 410 13.30 852 708 138 542 23
SP6, SPX 14.30 850 684 70 531 11
HELIX 14.30 850 720 137 590 10
GE *Starcam 2000 32.02 928 696 200 540 35
Starcam 3000, 32.02 928 696 200 540 35
3200, 4000
PICKER *PCS Plus – 0.9 12.50 794 642 132 488 7 0 - 100 0 - 100
DYNAPRO
W/S – Port “BW” and “IN” needs to be typed at the work station’s command
BW2 prompt.
SIEMENS ORBITER 13.30 824 650 100 492 7
* = Qualified
** = Requires NPSW3MIF – ADAC #2143-5525
SMV *DS7, *DST, 30.00 896 578 168 512 35
*NXT
TOSHIBA 602 27.20 816 522 151 419 20
* = Qualified

Table 2-9. Abbreviations for Tables 2-6 thru 2-8

Pix Clk Pixel Clock

C/L Clocks per line = Horizontal Total
HA Horizontal Active
HD Horizontal Delay
VA Vertical Active
VD Vertical Delay

2001 March Rev. M 1908110 2-29

Service Manual

2-10. 8300 IMAGER Contrast and Density Requirements

Note
The information in this paragraph applies to systems with software earlier than Version 4.2. For
systems with version 4.2 or later software, refer to paragraph 2-11.

A contrast test will create twelve numbered image tables of the last acquired image in memory. The first
six tables in the IMAGER are saggy curves intended for use with Ultrasound and Nuclear Medicine. Table
1 has a midtone brightness slightly lower than linear perceived brightness, with 2 through 6 having
progressively higher midtone brightness.
Tables 7, 9, and 11 typically appear in the first column of the second contrast test sheet and duplicate
tables from the familiar 713C0 transfer function. Table 7 resembles 713C0 table 6. Table 9 resembles
713C0 table 9, and table 11 resembles 713C0 table 12. These tables are commonly used by Ultrasound,
DSA, and C-Arm users. 713C0 has a higher midtone brightness than 693C0 for the same image Dmax.
Tables 8, 10, and 12 typically appear in the second column of the second contrast test sheet and
duplicate tables from the familiar 693C0 transfer function. Table 8 resembles 693C0 table 3. Table 10 is
linear and resembles 693C0 table 6. Table 12 resembles 693C0 table 9. These tables are applied over a
wide range of modalities that include MR, CT, CR, and Workstations. These contrasts are good choices
for starting points when printing preferences are not known.
Use Table 2-10 as a guide in anticipating what the customer may want to see from a particular modality.

2-30 1908110 2001 March Rev. M

Section 2 – Installation

Based on Field Test results the following density and contrast settings in Table 2-10 are recommended:
Table 2-10. Density and Contrast Settings Based on Field Test Results
Modality Manufacturer Study Contrast Density Sharpness Comments
Nuclear ADAC, Picker, Whole 3 , 4, 5, 6 5 through 8 Auto
Medicine SMV, Park body
Medical
Nuclear ADAC, Picker, Cardiac 6, 11 5 through 8 Auto
Medicine SMV, Park
Medical
Nuclear Toshiba All 1 or 2 5 or 6 Auto Check Toshiba
Medicine Camera Calibration
Ultrasound All All 3 through 6 8 through 12 Auto US Dmax
preferences are
trending to 2.4 and
higher
C-ARM All All 7,9,11 14 through 16 Auto
SDI, DST All All 7,9,11 14 through 16 Auto Curves 5 through 6
can lower
background density
if req’d.
Verify DSI camera
calibration.
MRI, CT All All 8,10,12 14 through 16 Auto Phillips may prefer
curves 2 through 5
Workstation All All Requires
workstation ULUT
contact Service
Engineering

Notes:
1. All contrast choices should be considered to meet customer preferences. The recommendations
given above are the most commonly used settings for the noted modalities.
2. The recommendations above refer to ULUT U1_109B, the default factory-installed ULUT.
3. The contrast test typically uses the last acquired image on a direct connection. If a contrast test is
performed with an MO disk, the first image on the disk is used.
4. The next paragraph describes ULUT options that are available with systems that have version 4.2 or
higher software. These systems can upload several new sets of contrast tables (from the SYSTEM
section of 83upgrad folder), using a terminal program such as Windows 95, Hyper-Terminal.

Note
The IMAGER system software must be at Version 4.2 or higher to take advantage of the new ULUT
options that can be stored in menu item MODALITY GROUPS. Follow the instructions to transfer a
text file in the same way that new machine code would be uploaded. Upload the new ULUT text file,
and the IMAGER will reprogram its flash memory with the new table. See the instructions in
paragraph 2-8 for further details on using a terminal program to transfer text files via the service port
of the IMAGER.

2001 March Rev. M 1908110 2-31

Service Manual

2-11. New ULUT Options

When Ver. 4.2 or higher software is uploaded to an 8300 IMAGER, a new menu item labeled “Modality
Groups” will be available in the Installation menu. Up to 11 different sets of contrast user look up tables
(ULUTs) can be uploaded into Modality Groups for selection by the technician. The file 8300ml03.txt,
located in the 4.4 or 4.6 “system” file folders in the 83upgrad folder on the Service CD-ROM, Rev. P,
contains seven sets of ULUTs that will reside in Modality Group locations 0–6. Before Ver. 4.2, the user
had to choose the most acceptable contrast table from only one set, which was actually a combination of
tables borrowed from more complete sets. With Ver 4.2 and later, and 8300ml03.txt loaded, that original
set will now reside in Modality Group location 0, and the IMAGER will default to that set if no other is
selected. (NOTE: With Ver. 4.2 and later, if 8300ml03.txt is not uploaded, the original set, U1_109B, will
reside in all 11 Modality Group locations, 0-10.) The following information summarizes the characteristics
of the contrast ULUT sets which will reside in Modality Groups 0–10 once software Ver. 4.2 or higher is
uploaded to the IMAGER.
Set 0: U1_109B (original set for the 8300 IMAGER)
This ULUT Set is the original standard ULUT Set for the 8300 IMAGER. It offers a variety of curve shapes
and mid-tone brightnesses, as can be seen from the graph in Figure 2-3, which shows all 12 ULUTs in this
set. Because this ULUT Set has such a diversity of curve shapes, with no simple relationship between
Contrast setting and either mid-tone brightness or mid-tone contrast, this set may be useful primarily as a
“finder” set, helping a user to decide on some other ULUT Set (e.g., UPMSV3K, 693C0, or 713C0) as a
preferred set, within which the curve shape varies in a more continuous way with Contrast setting than it
does in this ULUT Set.

Figure 2-3.

2-32 1908110 2001 March Rev. M

Section 2 – Installation

Set 0: U1_109B (C = 1 through 6)

The first six ULUTs (Contrast settings 1 through 6) of the U1_109B ULUT Set are “saggy” (i.e., non
S-shaped) curves, as shown in Figure 2-4. These are the most-used subset of the UPMSV3K ULUT
curves, which will reside in the Modality Groups as Set 1.

Figure 2-4.
For the above curves, overall image brightness increases as the Contrast setting is increased from 1 to 6.
These curves are often preferred over S-shaped curves by radiologists who are working with modalities
such as ultrasound or nuclear medicine.
Set 0: U1_109B (C = 7 through 12)
The remaining ULUTs (contrast settings 7 through 12) of the U1_109B ULUT Set consists of two groups,
each comprised of three S-shaped curves (see Figure 2-5).

Figure 2-5.

One group (curves 7, 9, and 11) is somewhat brighter than the other (curves 8, 10, and 12). Within either
group, increasing the Contrast setting increases the mid-tone contrast and decreases the contrast in the
near-black and near-white portions of the input range. (The reason for indexing by two instead of one in
this ULUT Set is to make a 2x3 image contrast test film easier to study visually, since all three images for
a given brightness group will then be in the same column on the film.) Curves 7, 9, and 11 are a subset of
the 713C0 ULUT Set (Modality Group Set 3), while curves 8, 10, and 12 are a subset of the 693C0 ULUT
Set (Modality Group Set 2). The applicability of the 693C0-type and 713C0-type curves to various
modalities is discussed below in the descriptions of the 693C0 and 713C0 ULUT Sets.

2001 March Rev. M 1908110 2-33

Service Manual

Set 1: UPMSV3K
This ULUT Set consists of a more complete set of “saggy” curves, providing a wider choice of
brightnesses than curves 1–6 of the U1_109B ULUT Set (see Figure 2-6). It is widely used in applications
including ultrasound, nuclear medicine, and others where an “S-shaped” response is not desired.
Because this ULUT Set is suitable for most ultrasound and nuclear medicine applications, it is an
appropriate choice for a majority of IMAGER users.

Figure 2-6.

For these curves, overall image brightness increases as the Contrast setting is increased from 1 to 12.
The brighter curves in this set are often preferred by radiologists working in ultrasound or nuclear
medicine.
Set 2: 693C0
This ULUT Set consists entirely of “S-shaped” curves with a mid-tone brightness that gives an
approximately “linear in perceived brightness” response, especially for the central Contrast settings of this
set (Figure 2-7).

Figure 2-7.

This ULUT Set is very suitable for CT, MR and C-Arm applications. It is also sometimes useful for nuclear
medicine applications. Increasing the Contrast setting from 1 to 12 increases the mid-tone contrast and
decreases the contrast in the near-black and near-white portions of the image.

2-34 1908110 2001 March Rev. M

Section 2 – Installation

Set 3: 713C0
This ULUT Set is comprised of a family of “S-shaped” curves similar to the 693C0 curves, but with a
somewhat elevated brightness (see Figure 2-8).

Figure 2-8.

This ULUT Set has rather wide applicability. It is often used for ultrasound, nuclear medicine, and DSA
and may also be used in other modalities where a brightness greater than that from the 693C0 Set is
desired.
Set 4: WKSTN83A
Most of the curves in this ULUT Set are designed to give a “linear in density” response, while the other
curves in this set are designed to give an approximate “linear in brightness” response. Because of its
linear in density curves, this ULUT Set is uniquely suitable for use with certain modalities or workstations
(e.g., Toshiba nuclear medicine or some Siemens workstations) that are designed to work with an
IMAGER which has a linear in density characteristic. Overall, this ULUT Set offers the choices seen in
Figure 2-9.

Figure 2-9.

2001 March Rev. M 1908110 2-35

Service Manual

Set 4: WKSTN83A (C = 1 through 8)

The linear in density curves in this ULUT Set are associated with contrast settings of 1 through 8
(Figure 2-10).

Figure 2-10.

The best curve (Contrast setting) to use in order to obtain a linear in density response depends on the
current Density (Dmax) setting, as indicated in the following table.

Contrast Setting for

Density Setting “Linear in Density” Response
15,16 1
13,14 2
11,12 3
9,10 4
7,8 5
5,6 6
3,4 7
1,2 8

When the Contrast setting is chosen from the above table for this ULUT Set, the printed density should
decrease in approximately equal steps of Optical Density as the Digital Input is increased by a given step
size.

2-36 1908110 2001 March Rev. M

Section 2 – Installation

Set 4: WKSTN83A (C = 9 through 12)

The approximately “linear in brightness” curves in this ULUT Set are obtained at Contrast settings of 9
through 12 (Figure 2-11). As the contrast setting is increased from 9 to 11, mid-tone contrast is increased
slightly while the contrast in the near-black and near-white portions of the image is decreased slightly.
Curve 12 is a repeat of curve 9. For further details on these “693C0-type” curves, see the description of
the 693C0 ULUT Set above.

Figure 2-11.

Sets 5 – 10: These ULUT Set numbers are reserved for future use. At present, each one contains a
repeat occurrence of the default ULUT Set. It is anticipated that future general ULUT releases may be
stored as Sets 6, 7, etc., while a custom ULUT Set may be stored as Set 10.

2001 March Rev. M 1908110 2-37

Service Manual

2-12. Installing Network Interface Board Software Upgrades

The Network Interface Board contains its own firmware that is independent of the system firmware. When
a Network Board is replaced, this firmware, called Network Interface Software (NIS), may have to be
updated.
1. Attach a PC to the serial service port and prepare for the upgrade as instructed in steps 1 through 8 of
paragraph 2-8.
2. To determine the level of the firmware on the board, press the TEST button on the Local Panel of the
IMAGER, and use the Arrow keys to display software versions.

Note
You can also review the versions remotely by using the Debug function (CTRL D) (see paragraph
7-1-2).

Note
Early production Network Boards incorrectly show the firmware revision level as 2.1. If the board
indicates this level, it must be updated.

3. Check the revision level of the latest NIS software on the MIS CDROM collection under the folder
83upgrade/network. (The CD will show the latest and former revision levels.)
4. If the Network Board does not contain the latest level firmware, download from the CDROM and
upload to the IMAGER. The procedure for loading is the same as that described in paragraph NO TAG
or 2-8 for system software, except that two files must be uploaded.
a. Start with the file named Network X-X.1 (where X–X is the software release number). This file is
small and takes only a short time to upload.
b. Continue with the file named Network X-X. 2. This file will take about 8 minutes to upload,
depending on what the baud rate is set at.

2-38 1908110 2001 March Rev. M

Section 3 – Adjustments

3-1. Processor Temperature Calibration

Specification
The temperatures displayed on the front panel must equal the temperatures displayed on the temperature
meter, approximately 122.2 ±1°C.

Note
This procedure should be performed whenever the processor drum or CPU PWA is replaced, or if
drum temperatures are suspected of causing image quality problems.

Special Tools
Temperature meter with probe and block

Note
A probe with a bar type element must be used to perform this procedure. Probes with circular type
elements will not provide accurate readings.

Note
The temperature meter and probe must be calibrated together as a pair at least once per year. If the
probe breaks, a new probe and the meter must be sent in for calibration. Refer to procedure 5-2 for
details.

Note
The temperature meter must be at room temperature when performing this procedure. If the meter
has been brought in from a hot or cold vehicle, allow it to acclimate to room temperature before use.

Calibration Procedure
1. Install the block on the probe as shown in Figure 3-1. Clean the probe with alcohol.

8-3/8”

Figure 3-1.

2000 March Rev. K 1908110 3-1

Service Manual

2. From the local panel menu, disable Film Calibration.

3. Remove the film tray and open the top cover.
4. Open the processor cover. Verify that the processor rollers are clean and free of deposits.

!
Caution
Deposits on the processor rollers could be knocked loose by the temperature probe, resulting in
damage to the surface of the drum. If necessary, clean the processor before continuing with this
procedure.

5. Close the processor cover.

6. Remove the left side panel.
7. Disconnect the mechanical processor drive arm from the top cover push rod.
8. Defeat the safety interlock. The recommended method is to use the serial service port/CPU
connector/cable.
9. Insert the film tray and film saver. Pull the film saver out approximately 1/4 inch to satisfy the local
panel message.
10. Wait for the IMAGER to warm back up to operating temperature.
11. Swing open the top wire film guide assembly to gain access to the processor entrance slot.
12. Set the meter to display temperatures in Celsius.

!
Caution

Hot Surface

The surfaces around the processor entrance slot are hot, and hot air exits through the slot. Do not
touch the surfaces around the slot, and do not hold the block outside the slot for prolonged periods
of time.

13. Center the probe and block where the center tine of the wire film guide assembly would be if in place.

14. Insert the probe in the processor entrance slot. Allow the rotation of the drum to pull in the probe until
the block reaches the outer edge of the slot.

Leftmost Tine Center Tine

Outer edge of Processor Entrance Slot

Figure 3-2.

3-2 1908110 2000 March Rev. K

Section 3 – Adjustments

15. Allow the block to rest squarely in the slot.

16. On the local panel, access the Cal Processor Center Temp submenu under the Installation menu.
17. Set the temperature displayed on the local panel to match the maximum temperature reading
displayed on the meter.
18. Continue monitoring the temperature for approximately five minutes to ensure that the temperature
change is taking effect.
Note
To display an updated temperature reading on the local panel, exit and re-enter the Cal Processor
Center Temp submenu.

19. Once the center temperature has stabilized, remove and clean the probe. Wait a full five minutes
before proceeding.

!
Caution
To prevent damage to the surface of the processor drum, remove and clean the probe after taking
each temperature reading.

20. Repeat steps 13 through 18, but align the edge of the probe this time with the left edge of the
processor entrance chute (refer to Figure 3-2), and access the Cal Processor End Temp submenu on
the local panel.
Note
Do not attempt to take a temperature reading at the right end of the processor. The probe will
interfere with the processor entrance switch.

21. Once the left end temperature has stabilized, remove and clean the probe. Wait a full five minutes
before proceeding.
22. Re-check the center zone temperature. If the local panel and meter readings differ by more than one
degree, repeat steps 13 through 22.
23. Remove the safety interlock defeat mechanism.
24. Reconnect the mechanical processor drive arm to the top cover push rod. Replace the left side panel.
Close the top cover and install the film tray.
25. From the local panel, enable Film Calibration.

2000 March Rev. K 1908110 3-3

Service Manual

3-2. Processor Drum Stripper Assembly

Specification
There must be a gap of 0.005 ± 0.001 inches between the processor drum and the stripper.

Special Tools
Feeler Gauge

Measurement
1. Remove the film tray and open the top cover.
2. Open the processor cover.
3. Verify that the processor drum and stripper are clean and free of deposits. If not, clean the processor
(refer to procedure NO TAG) before proceeding with this measurement procedure.

!
Caution

Hot Surface

The processor drum and stripper assembly are hot. Take care when checking the gap.

Note
When checking the gap, the roller assemblies at each end of the stripper must remain in contact with
the drum. Avoid lifting the entire stripper assembly when trying to slide the gauge between the drum
and stripper.

4. Try to slide a 0.004 feeler gauge between the drum and the stripper. If the gauge does not fit, the gap
is too small; perform the adjustment procedure.
5. Try to slide the 0.006 feeler gauge between the drum and the stripper. If the gauge fits, the gap is too
big; perform the adjustment procedure.

3-4 1908110 2000 March Rev. K

Section 3 – Adjustments

Adjustment for the One-Pad Stripper Assembly

Note
The stripper gap is changed by adjusting the position of the roller assemblies located at each end of
the stripper. Adjust one roller assembly at a time. Recheck the measurement after each adjustment.

1. Loosen the roller assembly securing screws.

2. Insert a flat screwdriver in the adjustment slot.
3. Rotate the screwdriver clockwise to increase the gap and counterclockwise to decrease it.
4. Tighten the roller assembly securing screws.
5. Recheck the measurement.

Top View from Front

Adjustment Slot Roller Assembly 8300–19C

Figure 3-3.

Adjustment for the Two-Pad Stripper Assembly

1. Adjust the allen screw (using a 3/32 inch Allen head ball driver) to obtain the proper gap between the
stripper and drum.
2. Turn the screw clockwise to decrease the gap and counter clockwise to increase it.
3. Recheck the Measurement.

Adjustment Screw

Roller Assembly

Figure 3-4.

2000 March Rev. K 1908110 3-5

Service Manual

3-3. One Sheet and Two Sheet Switches

Specification
DS2 on the CPU PWA must light when one sheet of film is detected between the separator rollers. DS1
(and DS2) on the CPU PWA must light when two sheets of film are detected between the rollers.

Special Tools
4/11/7 Mil Test Film
Two sheets of 7 mil film (14 mil)

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Remove power.
3. Remove the right side panel, and remove the lower input module.
4. Remove the access plate.
5. Swing open the wire film guide.
6. Turn on power.
7. Verify that DS1 and DS2 are not lit.
8. Insert the 4-mil portion of the test film between the separator rollers.
9. Reach down from above and rotate the upper separator roller to drive the film forward until the 4 mil
film is underneath the roller bearing (Figure 3-5).

Note
DS2 should light when one sheet of 4 mil film is initially detected. DS1 (and DS2) should light when
two sheets of 7 mil film are initially detected. Use the following steps to make the adjustments for
DS1 and DS2.

Top View from Right Side

Upper
Separator
Roller

Roller
Bearing

Figure 3-5.

10. If DS2 is not lit:

a. Loosen the one sheet sensor bracket securing screw.
b. Insert a flat blade screwdriver in the adjustment slot. Rotate the screwdriver to move the sensor
bracket just enough to light DS2.

3-6 1908110 2000 March Rev. K

Section 3 – Adjustments

c. Tighten the bracket securing screw.

d. Remove the test film.
11. If DS2 is already lit:
a. Insert a flat blade screwdriver in the adjustment slot.
b. Rotate the screwdriver to move the sensor bracket down until DS2 turns off.
c. Rotate the screwdriver in the opposite direction to where DS2 initially illuminates.
d. Remove the test film.
12. Insert two sheets of 7 mil film between the separator rollers.
13. Reach down from above. Rotate the upper separator roller to drive both sheets of film forward until
they are under the roller bearing.
14. DS2 should light again.
15. If DS1 does not light:
a. Loosen the two sheet sensor bracket securing screws.
b. Insert a flat blade screwdriver in the adjustment slot. Rotate the screwdriver to move the sensor
bracket enough to light DS1.
c. Tighten the bracket securing screw, and remove the two sheets of 7 mil film.
16. If DS1 is already lit:
a. Insert a flat blade screwdriver in the adjustment slot.
b. Rotate the screwdriver to move the sensor bracket until DS1 turns off.
c. Rotate the screwdriver in the opposite direction to where DS1 initially illuminates.
d. Remove the two sheets of 7 mil film.
17. Insert the 7 mil portion of the 4/11/7 mil test film between the separator rollers.
18. Reach down from above. Rotate the upper separator roller to drive the sheet of film forward until it is
under the roller bearing.
19. Verify that DS2 lights, but DS1 does not.
20. Continue to rotate the separator roller so the 11 mil portion of the test film is under the roller bearing.
21. Verify that DS2 is still lit and that DS1 remains unlit.
22. Back the test film out of the IMAGER.

Two Sheet Sensor

One Sheet Sensor
DS1
DS2

Figure 3-6.

2000 March Rev. K 1908110 3-7

Service Manual

3-4. Capstan Media Sense Switch

Specification
The switch must actuate when there is no film between the capstan roller and the pinch rollers, and
deactuate when film is present.

Special Tools
4 Mil Test Film

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Swing open the wire film guide.
3. Remove the left and right side panels.

Right Side View

Adjustment Screw

Figure 3-7.

3-8 1908110 2000 March Rev. K

Section 3 – Adjustments

4. Rotate the capstan several times while observing the switch arm.
5. Rotate the capstan to where the arm movement reaches the maximum point of travel (arm in the
position that is closest to the top of the unit).
6. Adjust the screw on the arm to where the switch initially actuates, and then tighten it one quarter turn
clockwise.
7. Rotate the capstan several times to verify that the switch does not deactuate.
8. Insert the 4-mil test film between the capstan roller and the upper pinch roller.
9. Turn the flywheel counterclockwise to drive the film between the capstan roller and the lower pinch
roller.
10. Verify that the switch deactuates. If not, back off the adjustment screw to the point where the switch
just deactuates.
11. Remove the film, and verify that the switch actuates.

Left Side View

Capstan Roller

Upper
Pinch
Roller

Lower
Pinch
Roller

Flywheel

Figure 3-8.

2000 March Rev. K 1908110 3-9

Service Manual

3-5. Film Saver Switch

Specification
The switch must actuate when the film saver is installed. When actuated, there should be a gap from
.001 to .002 inches between the actuator arm and the switch.

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Remove the right side panel.
3. Remove the MO drive (if present).
4. Insert the film tray and film saver.
5. Verify that the switch actuates when the film saver is inserted. If not:
a. Loosen the switch bracket mounting screws.
b. Move the bracket as required to actuate the switch.
c. Tighten the bracket mounting screws.

Figure 3-9.

3-10 1908110 2000 March Rev. K

Section 3 – Adjustments

3-6. Film Out Switch

Specification
The switch must actuate when the film tray is empty. When actuated, there should be a gap from 0.001 to
.002 inches between the actuator arm and the switch.

Note
When the film tray is empty (or removed), the actuator bar should rest on the limit pin.

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Remove the right side panel.
3. Remove the MO drive (if present).
4. Remove all film from film tray, and insert empty film tray.
5. Verify that the switch actuates when the actuator arm drops into slot in film tray. If not:
a. Loosen the switch bracket mounting screws.
b. Move the bracket as required to actuate the switch.
c. Tighten the bracket mounting screws.

Figure 3-10.

2000 March Rev. K 1908110 3-11

Service Manual

3-7. Film Tray In-Place Switch

Specification
The switch must actuate when the film tray is removed.

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Remove the right side panel.
3. Verify that the switch actuates when the film tray is removed. If not:
a. Loosen the switch bracket mounting screws.
b. While holding the actuator lever in its leftmost position, move the bracket as required to actuate
the switch.
c. Tighten the bracket mounting screws.

Figure 3-11.

3-12 1908110 2000 March Rev. K

Section 3 – Adjustments

3-8. Film Tray Lock Switch

Specification
The switch is actuated as long as a film tray is fully installed in the imager or the tray is fully removed.
The switch is deactuated when the mechanical release is actuated or when the solenoid is actuated for
5-10 seconds, during the tray ejection procedure.

Measurement
1. Remove the film tray and open the top cover.
2. Remove both side panels and the front panel.
3. Verify that the switch is actuated. If not, loosen the switch securing screws slightly. Reposition the
switch so that it is actuated, then tighten the securing screws.

Note
The switch securing screws thread into a nut plate. Do not loosen them too much or the nut plate
may fall off.

4. Slide the film tray half way into the imager.

5. Verify that the switch is deactuated. If not, loosen the switch securing screws slightly. Reposition the
switch so that it is deactuated, then tighten the securing screws.
6. Remove the film tray, then repeat steps 3 through 5.

Front View

Figure 3-12.

2000 March Rev. K 1908110 3-13

Service Manual

3-9. Capstan Belt

Specification
The belt must be tight enough to prevent slippage between the belt and the flywheel. The longest span of
the belt should deflect approximately 1/6 inch when finger pressure is applied.

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Remove the left side panel.
3. Check the tension of the belt. If the tension requires adjustment:
a. Remove the Motor Control PWA.
b. Loosen the belt tensioner assembly securing screws.
c. Slide the belt tensioner assembly up or down as required.
d. Tighten the belt tensioner assembly securing screws.

Belt Tensioner Assembly

Figure 3-13.

3-14 1908110 2000 March Rev. K

Section 3 – Adjustments

3-10. Separator Roller Belt

Specification
The belt is adjusted as loosely as possible, while ensuring that the belt teeth mesh properly with the teeth
on the gears. The belt should not jump teeth when film is fed through the separators.

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Remove the left side panel.
3. Run transport test.
4. Check the tension of the belt while feeding film as during a transport test. If the tension requires
adjustment:
a. Stop transport test.
b. Loosen the belt tensioner.
c. Slide the belt tensioner up or down as required.
d. Tighten the belt tensioner.
e. Recheck tension.

Belt Tensioner

Figure 3-14.

2000 March Rev. K 1908110 3-15

Service Manual

3-11. Main Drive Belt

Specification
The teeth on the belt must mesh properly with the teeth on the gears while film is fed. The longest span of
the belt should deflect a maximum of 1/2 inch when finger pressure is applied.

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Remove the left side panel.
3. Check the tension of the belt. If the tension requires adjustment:
a. Loosen the belt tensioner securing screw.
b. Rotate the belt tensioner as required.
c. Tighten the belt tensioner securing screw.

Belt
Tensioner

1/2 inch

Figure 3-15.

3-16 1908110 2000 March Rev. K

Section 3 – Adjustments

3-12. Processor Belt

Specification
The teeth on the belt must mesh properly with the teeth on the gears. The longest span of the belt should
deflect a maximum of 1/2 inch when finger pressure is applied.

Measurement/Adjustment
1. Remove the film tray and open the top cover.
2. Remove the left side panel.
3. Check the tension of the belt. If the tension requires adjustment:
a. Loosen the belt tensioner assembly securing screw.
b. Rotate the belt tensioner assembly as required.
c. Tighten the belt tensioner assembly securing screw.

1/2 inch

Belt Tensioner
Assembly

Figure 3-16.

2000 March Rev. K 1908110 3-17

Service Manual

3-13. Processor Drive Arm Gear

Specification
The processor drive arm gear must positively engage with the processor gear. The teeth on each gear
must not bottom out on the opposite gear.

Measurement
1. Remove the film tray and open the top cover.
2. Remove the left side panel.
3. Close the top cover.
4. Verify that the processor drive arm gear engages properly with the processor gear. If not:
a. Loosen the lock nut on the adjustment screw.
b. Rotate the adjustment screw as required.
c. Tighten the lock nut.

Processor Gear

Processor Drive
Arm Gear

Adjustment
Screw

Lock Nut

Figure 3-17.

3-18 1908110 2000 March Rev. K

Section 4 – Disassembly/Reassembly

4-1. Reassembly
After performing a disassembly procedure, reverse the steps for reassembly.

4-2. Covers and Panels

4-2-1. Left or Right Side Cover

1. Remove the film tray.

! Warning
When the power cord is plugged in, hazardous voltages are present in some areas of the IMAGER.
These voltages can cause severe injury or death.
2. Raise the top cover.
3. Remove three screws.
4. Grasp the cover by the bottom and pull out to remove it.

Figure 4-1.

2001 March Rev. M 1908110 4-1

Service Manual

4-2-2. Front Panel

1. Turn off power and disconnect the power cord.

! Warning
When the power cord is plugged in, hazardous voltages are present in some areas of the IMAGER.
These voltages can cause severe injury of death.

2. Remove the film tray.

3. Remove both the left and right side covers (see paragraph 4-2-1).
4. Remove two screws from the bottom of the cover.
5. Loosen two screws (one on each side).
6. Pull the cover off from the front.

Figure 4-2.

4-2 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-2-3. Rear Panel

1. Turn off power and disconnect the power cord from the rear of the machine.

! Warning
When the power cord is plugged in, hazardous voltages are present in some areas of the IMAGER.
These voltages can cause severe injury or death.

2. Remove the left side cover (see paragraph 4-2-1).

3. Disconnect P1 and P2 from the Motor Control PWA.

Note
Do not remove the screws that hold the exhaust fan to the rear panel.

4. Remove nine screws from the rear panel, and remove the panel

Figure 4-3.

2001 March Rev. M 1908110 4-3

Service Manual

4-2-4. Capstan Roller Front Cover

1. Remove the film tray.
2. Turn off power and disconnect the power cord.

! Warning
When the power cord is plugged in, hazardous voltages are present in some areas of the IMAGER.
These voltages can cause severe injury or death.

3. Raise the top cover.

4. Remove three screws from front capstan cover.
5. Remove the cover.

Figure 4-4.

4-4 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-3. Electronic Circuit Modules/PWAs/Components

4-3-1. Interface Modules

Note
For Network Interface Boards: If possible, access and record the installation and customer preference
parameters for this board from the Local Panel.

Disassembly
1. Turn off power and disconnect the power cord.
2. Remove the external cables from the PWA.
3. Remove the right side cover (see paragraph 4-2-1).
4. Remove the cables (if any) that connect to the PWA.
5. Remove the four screws that secure the PWA to the inside of the machine.
6. Remove the two screws that secure the external connector plate to the machine.
7. Slide the PWA out the back of the machine.
Reassembly
1. Make sure that all four mounting screws are installed when you mount the interface module in the
IMAGER. If they are not, the ground of the interface module may be affected.
2. For a Network Interface Module: Make sure the the module is installed in the top (A) slot.

Note
When a Network Interface Board is replaced, you may have to update the firmware on the new
board. (See paragraph 2-12 for instructions.) Also, you must reload the parameters recorded earlier
(see Note at beginning of Disassembly) or stored in the Service History Log.

Note
When a Digital or Analog Interface Board is replaced, be sure to place the CTS/RTS – ±12V Switch in
the CTS/RTS position for host control or in the ±12V position for remote keypad control.

Figure 4-5.

2001 March Rev. M 1908110 4-5

Service Manual

4-3-2. CPU PWA

Note: If possible, access and record the installation and customer preference parameters from the
local panel.

1. Turn off power and disconnect the power cord.

2. Remove the right side cover (paragraph 4-2-1).
3. Disconnect all electrical plugs from the PWA.
4. Remove six screws.
5. Slide the CPU PWA toward the machine front to disconnect it from the input module(s).
6. Install new CPU PWA and transfer the memory SIMMs from the old CPU PWA. Refer to 4-3-2-1.
7. Install the latest software (see paragraph NO TAG or 2-8) that is available in CDROM folder 83 upgrad.
8. Reload the parameters recorded earlier (see Note above) or stored in the Service History Log.
9. Recalibrate drum temperature (paragraph 3-1), and update the film count.

Figure 4-6.

4-6 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-3-2-1. SIMMs in the CPU PWA

Note
When installing SIMMs, always use a wrist strap to prevent damage from electro-static discharge.

1. Turn off power and disconnect the power cord.

2. Remove the right side cover. (See paragraph 4-2-1.)
3. If replacing a SIMM, push back retaining clips on both sides of the SIMM and lift. (See Figure 4-7 for
the approximate angle.)
4. Pull the SIMM out of the connector.

Note
If installing just one SIMM, always use the bottom slot on the CPU PWA.

5. Install the SIMM in the connector at an angle with the key toward the front of the imager (Figure 4-7),
and then push down to secure in place with the retaining clips.

Figure 4-7.

2001 March Rev. M 1908110 4-7

Service Manual

4-3-3. Motor Control PWA

1. Turn off power and disconnect the power cord.
2. Remove the left side cover (see paragraph 4-2-1).
3. Disconnect all electrical plugs from the PWA.
4. Remove four screws.
5. Remove the PWA.

Figure 4-8.

4-8 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-4. Electronic Modules

4-4-1. Optics Module

1. Turn off power and disconnect the power cord.
2. Remove the rear panel (see paragraph 4-2-3).
3. Disconnect cable plugs P1 and P2 from the optics module.
4. Remove three Allen screws.
5. Lift the optics module out of the machine.

Figure 4-9.

2001 March Rev. M 1908110 4-9

Service Manual

4-4-2. Power Module

1. Turn off power and disconnect the power cord.
2. Remove the left and right side covers (see paragraph 4-2-1).
Note
The front panel may be loosened to facilitate removal.
3. Disconnect the electrical connectors from the right side of the module (Figure 4-10).
4. Disconnect the fan motor connector from the Motor Control PWA.

Figure 4-10.
5. Remove one screw from the left side of the power module and disconnect the electrical connector from
the power switch cable (Figure 4-11).
6. Slide the power module out the left side of the machine (Figure 4-11).

Figure 4-11.

4-10 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-4-3. Densitometer Assembly

1. Turn off power and disconnect the power cord.
2. Remove the film tray.
3. Raise the top cover.
4. Remove the top plate by removing three screws.
5. Remove the right side cover to access the CPU PWA.
6. Disconnect the inline connector leading from P4 on the CPU PWA.
7. Disconnect P3 from the CPU PWA.
8. Remove vertically aligned screws from the left and right ends of the densitometer assembly, then
remove it. (The exit sensor is also installed on the mounting plate.)

Figure 4-12.

2001 March Rev. M 1908110 4-11

Service Manual

4-4-4. Local Panel

1. Turn off power and disconnect the power cord.
2. Remove the film tray.
3. Raise the top cover.
4. Remove four screws.
5. Disconnect the electrical connector and remove the local panel.

Figure 4-13.

4-12 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-4-5. SCSI Drive (Option)

1. Turn off power and disconnect the power cord.
2. Remove the right side cover (see paragraph 4-2-1).
3. Remove the front panel (see paragraph 4-2-2).
4. Disconnect the cable leading from electrical plug P3 on the power module.
5. Disconnect the large signal cable from the SCSI drive.
6. Remove three screws and remove the SCSI drive.

Figure 4-14.

2001 March Rev. M 1908110 4-13

Service Manual

4-5. Switches and Sensors

4-5-1. Top Cover Interlock

1. Turn off power and disconnect the power cord.
2. Remove the left side cover (see paragraph 4-2-1).
3. Remove the three screws securing the exhaust fan to the rear panel, and move the fan out of the way
(Figure 4-15).
4. Disconnect the two electrical wires from the switch (Figure 4-16).
5. Remove two attaching screws and remove the interlock switch.

Figure 4-15.

Figure 4-16.

4-14 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-5-2. Processor Entrance Sensor

1. Turn off power and disconnect the power cord.
2. Remove the processor assembly (see paragraph 4-7-1).
3. Remove four screws from the entrance guide plates.
4. Disconnect the electrical connector.
5. Push the feet of the sensor housing toward the frame to release the sensor.

Figure 4-17.

2001 March Rev. M 1908110 4-15

Service Manual

4-5-3. Processor Exit Sensor

Figure 4-18.

4-16 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-5-4. One Sheet and Two Sheet Sensors

1. Turn off power and disconnect the power cord.
2. Remove the right side cover (see paragraph 4-2-1).
3. If there is an interface module in the lower (B) location, remove it (see paragraph 4-2-3).
4. Remove three screws, and remove the cover plate (Figure 4-19).
5. Remove the two screws securing the one sheet and two sheet sensor bracket (Figure 4-20).
6. Disconnect the electrical connector from the sensor, and remove the sensor from the bracket.

Figure 4-19.

Figure 4-20.

2001 March Rev. M 1908110 4-17

Service Manual

4-5-5. Capstan Media Sense Switch

1. Turn off power and disconnect the power cord.
2. Remove the right side cover (see paragraph 4-2-1.
3. Remove the upper input module (Figure 4-21 and paragraph 4-2-3).
4. Disconnect the leads from the switch (Figure 4-22).
5. Remove two screws, and remove the switch.

Figure 4-21.

Figure 4-22.

4-18 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-5-6. Film Out and Film Saver in Place Switches

1. Turn off power and disconnect the power cord.
2. Remove the right side cover (see paragraph 4-2-1).
3. Remove the SCSI drive, if one is used (see paragraph 4-5-5).
4. Disconnect the leads from the switch.
5. Remove two screws and remove the switch.

Figure 4-23.

2001 March Rev. M 1908110 4-19

Service Manual

4-5-7. Film Tray in Place Switch

1. Turn off power and disconnect the power cord.
2. Remove the right side cover (see paragraph 4-2-1).
3. Remove the CPU PWA (see paragraph 4-3-2).
4. Disconnect the leads from the switch.
5. Remove two screws and remove the switch.

Figure 4-24.

4-20 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-6. Film Feed Components

4-6-1. Film Tray Lock Assembly

1. Turn off power and disconnect the power cord.

! Warning
When the power cord is plugged in, hazardous voltages are present in some areas of the IMAGER.
These voltages can cause severe injury or death.

2. Remove the left and right side covers (see paragraph 4-2-1.
3. Remove the front panel (see paragraph 4-2-2).
4. Disconnect the film tray release solenoid electrical plug from P9 of the Motor Control PWA.

Note
The solenoid wires (white) are in a mini plug that can be disconnected separately from the other mini
plugs in the P9 connector (see the inset in the illustration).

5. Remove the two screws attaching the power switch box. Carefully pull the box away from the chassis
and turn it to expose the wire connections.
6. Disconnect the power switch in-line connector.
7. Disconnect the four leads attaching to the power line filter in the switch box.
8. Disconnect the two electrical leads from the film tray lock switch.
9. Remove three attaching screws, and remove the film tray lock assembly.

Figure 4-25.

2001 March Rev. M 1908110 4-21

Service Manual

4-6-2. Film Feed Roller Assembly

1. Turn off power and disconnect the power cord.
2. Remove the power module (paragraph 4-4-2).
3. Remove the processor (paragraph 4-7-1).
4. Remove two setscrews each from two belt pulleys, and remove the pulleys and belts (Figure 4-26).
5. Remove one setscrew from the roller.
6. Remove shaft and roller.
Reassembly hint: Line up all pulleys and belts so that setscrew holes are aligned over shaft flats before
securing the pulleys to the shafts.

Figure 4-26.

4-22 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-6-3. Separator Assembly

1. Turn off power and disconnect the power cord.
2. Remove the left and right side covers (see paragraph 4-2-1).
3. Remove the CPU PWA (see procedure 4-3-2).
4. Remove the three attaching screws from the separator block on the right side (Figure 4-27).
5. Remove the separator belt (Figure 4-28) from the clutches on the left side (see paragraph 4-8-3).
6. Disconnect plug P8 from the Motor control PWA.
7. Remove four screws from the separator block on the left side.
8. Pull the separator assembly out the left side of the machine.

Figure 4-27.

Figure 4-28.

2001 March Rev. M 1908110 4-23

Service Manual

4-6-4. Capstan Roller

1. Turn off power and disconnect the power cord.
2. Remove left and right covers (paragraph 4-2-1).
3. Remove the rear panel (paragraph 4-2-3).
4. Remove the capstan roller front cover (paragraph 4-2-4).
5. Pivot the wire guides for access (Figure 4-29).
6. Remove the capstan belt (paragraph 4-8-7).
7. Remove the attaching screw and clamp, and remove the capstan drive gear (Figure 4-30).
8. Remove the CPU PWA (procedure 4-3-2).
9. Remove the E-ring, washer and bearing from the right end of the capstan roller (Figure 4-31).
10. Remove the bearing from the left end of the roller (Figure 4-31).
11. Slide the capstan roller to the left until it clears the right side chassis, and remove it.

Figure 4-29.

4-24 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

Figure 4-30.

Figure 4-31.

2001 March Rev. M 1908110 4-25

Service Manual

4-6-5. Capstan Pinch Rollers

1. Turn off power and disconnect the power cord.
2. Remove the left and right side covers (paragraph 4-2-1).
3. Remove the capstan roller (paragraph 4-2-4).
4. Remove the upper (A) input module (paragraph 4-3-1).
5. Remove two screws from the bearing block on the left side (Figure 4-32). (Rotate the capstan pulley
as necessary to access the screws.)
6. Remove two screws from the bearing block on the right side (Figure 4-33).
7. Pivot the capstan pinch roller assembly and remove it from the machine.

Note
Prevent the assembly from coming apart when reinstalling. Two different size springs hold roller in
place.

Figure 4-32.

Figure 4-33.

4-26 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-7. Processor Components

4-7-1. Processor Assembly

1. Turn off power and disconnect the power cord.
2. Allow the processor to cool down.
3. Remove the left and right side covers (see paragraph 4-2-1).
4. Disconnect the plugs from P2, P3, and P4 of the CPU PWA (Figure 4-34).
5. Disconnect the plug from P5 of the power module.
6. Remove four attaching screws from the processor assembly (Figure 4-35).
7. Lift the processor assembly from the machine.

Note
If the processor is replaced with a new processor, temperature must be calibrated after reassembly.
See paragraph 3-1.

Figure 4-34.

Figure 4-35.

2001 March Rev. M 1908110 4-27

Service Manual

4-7-2. Processor Half

1. Turn off power and disconnect the power cord.
2. Allow the processor to cool down.
3. Remove the left and right side covers (see paragraph 4-2-1).
4. Remove two screws (one from each side).
5. Unlatch the processor cover.
6. Remove the processor half.

Figure 4-36.

4-28 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-7-3. Processor Drum

1. Turn off power and disconnect the power cord.
2. Allow the processor to cool down.
3. Remove the processor half (see paragraph 4-7-7).
4. Disconnect the plugs from P2 of the CPU PWA and P5 of the power module (Figure 4-37).
5. Disconnect the ground wire from the right side of the processor assembly.
6. Remove two locking plates (one from each side) of the processor drum (Figure 4-38).
7. Turn the bearing blocks to align the flats for removal. Then lift the drum from the machine.

Note
If the drum is replaced with a new drum, calibrate processor temperature after reassembly. See
paragraph 3-1.

Figure 4-37.

Figure 4-38.

2001 March Rev. M 1908110 4-29

Service Manual

4-7-4. One-Pad Stripper Assembly

1. Turn off power and disconnect the power cord. Allow the processor to cool down.
2. Remove the processor drum ( paragraph 4-7-3).
3. Disconnect two springs from the stripper assy.
4. Remove two shoulder screws, one from each end of the stripper.
5. Remove the stripper assembly.
6. To install a new felt pad assembly:
a. Remove the standoffs securing the pad assy.
b. Note that the pad assembly has a wide bend in the metal backing plate, causing it to be inclined
by 1/8 inch when in place. As you install the new pad in the next step, tighten the standoffs only
enough so the new pad bends only slightly.
c. Tighten the standoffs while holding the felt pad against the metal stop of the stripper blade (toward
machine front).

Note
There must be no gap betwen the metal backing of the felt pad and the metal stop of the stripper
blade.

Figure 4-39.

4-30 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-7-5. Two-Pad Stripper Assembly

1. Turn off power and disconnect the power cord.
2. Allow the processor to cool down.
3. Remove the processor drum (paragraph 4-7-3).
4. Remove the screws from the ends of the stripper shaft.
5. Slide the stripper assembly to the right.
6. Lift out the assembly, using care not to lose the two end springs.
7. To install a new lower felt pad assembly, refer to the instructions for installing the pad for the One-Pad
Stripper in paragraph 4-7-4.
8. Replace the original top felt pad as follows:
a. Make sure that the felt of the top pad faces down toward the felt of the lower pad.
b. After the mounting screws are tightened, the top pad should float and move freely, and be allowed
to touch the lower felt pad.

Figure 4-40.

2001 March Rev. M 1908110 4-31

Service Manual

4-7-6. Lower Roller Assembly

1. Remove the processor drum (see procedure 4-7-3).
2. Remove the screw retaining clip from the right lower shaft (right side determined by facing the
machine).
3. To access screw on the left rear shaft, disconnect the spring and top cover push rod from the
mechanical processor drive arm.
4. Remove screw from left side of front shaft and left side of rear shaft.

Note
The drum belt bearing block screws may require removal, which will allow the bearing block to pivot
in order to remove the rear shaft from the left side.

5. Pull the shafts from the right side.

6. Remove the lower roller assembly.

Figure 4-41.

4-32 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-7-7. Ultem Film Entrance Guide

1. Remove lower roller assembly (see procedure 4-7-6).
2. Remove two shoulder screws.
3. Remove film guide.

Note
The shoulder screw heads should face down during assembly.

Figure 4-42.

2001 March Rev. M 1908110 4-33

Service Manual

4-7-8. Thermal Fuses

There were two early configurations of fuses in the processor drum: One used four fuses (two end zone
and two center zone, as shown in figure 4-43). The other used three fuses (two end zone and one center
zone. The current configuration has only two (192°) fuses (one center zone and one end zone).
Processors with the new configuration are identified by a 192° label attached to the slip ring plate.
If a fuse blows on an early configuration, the drum must be updated to the new configuration as described
below.
Upgrading an Early Configuration/Replacing Fuses
1. Remove the processor drum (procedure 4-7-3).
2. Remove the right side end cap (slip ring side).
3. Slide end zone fuse #1 (white wires) from its sleeve (see figure 4-43).
4. Cut both wires close to the crimped connectors (wire side) to remove the fuse.
5. Solder the wires together and slide the connection back into the sleeve.

End Zone Cut wires to

Fuse #4 Fuse, then
solder wires
together
End Zone
Fuse #1

Center Zone
Fuse #3
Center Zone
Fuse #2

Processor Drum Assembly 8300–187C

Figure 4-43.

6. Repeat steps 3 through 5 for center zone fuse # 2 (red wires), if the fuse is present.
7. Remove the left side end cap (gear side).
8. Slide end zone fuse #4 (white wires) from its sleeve.
9. To remove the fuse, cut both wires close to the crimped connectors (wire side).
10. Trim the leads of the new fuse to 1/2 inch (13 mm).

!
Caution
Heat from soldering may cause the new fuse to open. Use a heat sink (e.g., a hemostat) on the
fuse side to prevent damaging the fuse.

11. Twist the wires cut from end zone fuse #4 to the new fuse, and solder.

4-34 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

12. Slide the new fuse into the sleeve.

13. Slide center zone fuse #3 from its sleeve and repeat steps 8 through 12 for fuse #3.
14. Reassemble the drum, and reinstall it.
Replacing a New Configuration Fuse
1. Remove the processor drum (procedure 4-7-3), and remove the left end cap (gear side).
2. Slide the blown fuse (white wires for end fuse, red wires for center fuse) from its sleeve and unsolder
it.
3. Trim the leads of the new fuse to 1/2 inch (13 mm).

!
Caution
Heat from soldering may cause the new fuse to open. Use a heat sink (e.g., a hemostat) on the
fuse side to prevent damaging the fuse.

4. Solder the new fuse in place, slide it into the sleeve, and reassemble.

4-8. Drive Belts

4-8-1. Film Feed Belt

1. Turn off power and disconnect the power cord.
2. Remove the left side cover (see paragraph 4-2-1).
3. Remove the E-ring and washer from the film feed clutch shaft, and pull the clutch out to the end of the
shaft.
4. Loosen the two setscrews in the pulley on the end of the motor shaft, and remove the pulley and belt.

Figure 4-44.

2001 March Rev. M 1908110 4-35

Service Manual

4-8-2. Film Feed Roller Assembly Belts

1. Turn off power, and disconnect the power cord.
2. Remove the power module (see paragraph 4-4-2).
3. Remove the processor (see paragraph 4-7-1).
4. Remove the four screws attaching the film feed clutch.
5. Remove the film feed drive belt.
6. Remove three E-rings from the feed clutch shaft.
7. Remove the four setscrews attaching the two belt pulleys to the clutch drive shaft.
8. Pull the clutch drive shaft out the left side of the machine to free the two belts. Then remove the belts.

Figure 4-45.

4-36 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-8-3. Separation Belt

1. Turn off power and remove the left side cover (see paragraph 4-2-1).
2. Disconnect the tension spring for the cover rod.
3. Loosen the belt tensioner.
4. Remove the belt.
5. After replacing a belt, adjust belt tension (see paragraph 3-9).

Figure 4-46.

2001 March Rev. M 1908110 4-37

Service Manual

4-8-4. Main Belt

1. Turn off power and remove the separation belt (see paragraph 4-8-3).
2. Remove the main belt tensioner (Figure 4-47).
3. Remove the two screws attaching the bearing block for the drum belt assembly.
4. Pull the bearing block and drum belt assembly away from the chassis and slide the belt off the pulley
(Figure 4-48).
5. Remove the main belt.
6. After replacing the separation belt and main belt, adjust belt tension (see paragraphs 3-9 and 3-10).

Figure 4-47.

4-38 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

Figure 4-48.

2001 March Rev. M 1908110 4-39

Service Manual

4-8-5. Drum Belt/Common Bearings

1. Turn off power and remove the left side cover (see paragraph 4-2-1).
2. Disconnect the top cover rod and spring (Figure 4-49).
3. Loosen the main belt tensioner to provide slack in the the main belt.
4. Remove two screws attaching the bearing block for the drum belt assembly and slide the main belt off.
5. Separate the drum belt assembly from the bearing block.
6. Remove two E-rings (Figure 4-50).
7. Remove two sets of pulley setscrews.
8. Pull the two pulley shafts from the assembly bracket to free the belt and common bearings.

Figure 4-49.

4-40 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

9. Replace the drum belt.

10. Replace the common bearings.

Figure 4-50.

2001 March Rev. M 1908110 4-41

Service Manual

4-8-6. Processor Belt

1. Turn off power and remove the left side cover (see paragraph 4-2-1).
2. Loosen the screw for the tensioner assembly.
3. Pull down the tensioner and remove the belt.
4. After replacing a belt, adjust belt tension (see paragraph 3-11).

Figure 4-51.

4-42 1908110 2001 March Rev. M

Section 4 – Disassembly/Reassembly

4-8-7. Capstan Belt

1. Turn off power and remove the left side cover (see paragraph 4-2-1).
2. Remove the Motor Control PWA to gain access to the capstan belt tensioner (see paragraph 4-3-3).
3. Loosen the belt tensioner.
4. Slide the belt off the motor shaft. Then remove it from the capstan flywheel and turn it sideways to
slide it between the flywheel and the exhaust fan.
5. After replacing a belt, adjust belt tension (see paragraph 3-8).

Figure 4-52.

2001 March Rev. M 1908110 4-43

Service Manual

BLANK PAGE

4-44 1908110 2001 March Rev. M

Section 5 – Additional Information

5-1. Required Tools

In addition to standard hand tools (screwdrivers, wrenches, etc.), the tools listed in this subsection are
required to service the 8300 IMAGER. All the tools are available from Service Parts Management.
1. Fluke DVM, Model 87 (or equivalent) TL-4114
2. Dual trace oscilloscope TL-3348
Band Width: 0 to 100 MHz
Sensitivity: 0.5 mv
Accuracy: " 3%
3. Temperature Meter Kit (includes Minco temperature meter and 11-inch bar type probe, calibrated as a
pair at the factory) 78-8099-9500-0
4. Probe (11-inch bar type) 26-1011-8560-6

Note
If a new probe is ordered, the probe and meter must be sent in for calibration. See procedure 5-2.
5. Block (for use with probe) 78-8064-5583-4
6. 4/11/7 Mil Test Film 78-8096-3223-1
7. Cable, PC to AFHU 78-8075-6004-6
8. Connector, BNC T, F-M-F 83-1610-0141-3
9. Terminator, BNC, 75 Ohm 26-1008-4885-7
10. Adapter, BNC, F-to-F 83-1610-0154-6
11. M/O Test Disk 78-8079-0527-4
12. Static Protection Kit (includes a static dissipative work surface, a ground cord, two sizes of wristbands,
and an alligator clip) TL-3397
13. 3/32-inch Ball End Hex Wrench (for
stripper gap adjustment) TL-1607

5-2. Temperature Meter and Probe Calibration

The temperature meter and bar type probe must be calibrated together as a pair at least once per year.
Send the meter, probe, and calibration form to:
National Calibration and Testing Laboratories
6960 Madison Avenue West
Minneapolis, MN 55427
The calibration process takes approximately 1 week. Send the meter and probe in for calibration prior to
going on vacation. This will ensure that they will be available for use when needed.

2001 September Rev. N 1908110 5-1

Service Manual

5-3. Preventive Maintenance

Effective with Version 4-2 system software, a PM Counter automatically displays a “Schedule PM”
message on the local panel to alert the operator to place a PM service call.

5-3-1. Cleaning Materials and Supplies

All materials and supplies are vailable from Service Parts Management.
• Insulated rubber gloves* 77-8007-2908-7
• 100% Isopropyl alcohol*, 1 quart 78-8033-7475-6
• Bag with Twist-Tie (3 gallon)* 78-9998-2868–0
• Low-lint alcohol-saturated wipes (TEXWIPE TX1065) 1C8287
• Cleaning cloths (TEXWIPE TX312) 78-8005-3779-3
• Presoaked alcohol pads (TEXWIPE TX801) 1C8282
• All-purpose cleaning pads* (3M O-Cel-O) 96-0000-0057-8
*Can be obtained locally.

!
Caution
The cleaning materials used during emergency maintenance (EM) and preventative maintenance
(PM) calls may create odors that are offensive to users and patients, so schedule the maintenance
accordingly. Cleaning should be done in a well ventilated area. At a minimum, this should be an
area that meets standards for general office ventilation. Wear appropriate personal protective
equipment, such as gloves, to avoid prolonged contact of cleaning agents with skin.

5-3-2. EM Call Checklist

The following procedures must be performed on every EM call. However, if the number of cycles since the
last PM is greater than 8000, reset the PM Counter and perform the PM procedures (see paragraph 5-5)
instead of the procedures in the EM checklist.
1. Review the Material Safety Data Sheets for the cleaning products before you perform the following
procedures.
2. Open the processor cover, and check the drum for damage.
3. If the drum is damaged, replace it (procedure 4-7-3).

Note
Before replacing the drum, clean the processor rollers and stripper blade with cleaning pads and
isopropyl alcohol.

4. If the drum is not damaged:

a. Allow the drum to cool for 10 to 15 minutes, then check that it is to cool to the touch. When cool,
clean the drum using a TX312 cleaning cloth and isopropyl alcohol.
b. Clean the stripper blade with a TX312 cleaning cloth and isopropyl alcohol.
c. If the processor rollers are extremely dirty, clean them with a TX312 cleaning cloth and isopropyl
alcohol.
5. Clean the stripper blade with a TX312 cleaning cloth and isopropyl alcohol.

5-2 1908110 2001 September Rev. N

Section 5 – Additional Information

5-3-3. Preventive Maintenance (PM) Scheduling

The PM Counter automatically displays a “Schedule PM” message on the local panel to alert the operator
to place a PM service call. In order to consistently produce the highest quality images, perform the
following PM procedures on the IMAGER every 10,000 cycles.

5-3-4. 10,000 PM Checklist

Following is a checklist of PM procedures that are to be performed at successive 10,000 machine cycle
intervals. The procedures with time intervals are also summarized in Table 5-1.

! Warning
All disassembly is to be performed with power removed from the machine and the power cord
unplugged. When the power cord is plugged in, hazardous voltages are present in some areas of
the IMAGER. These voltages can cause severe injury or death.
- 1. Inspect and clean the Film Tray and Film Feed Roller. (See paragraph 5-3-6.)
- 2. Clean the Fan Filter, Charcoal Filter, and Faz Filter. (See paragraph 5-3-7.)

Note
Every 20,000 cycles the Charcoal Filter must be replaced, and every 60,000 cycles the Faz Filter
must be replaced.

- 3. Clean the Laser Scanning Area, Capstan, and Pinch Rollers. (See paragraph 5-3-8.)
- 4. Clean the Scoop, Film Guide Area, 1-2 Sheet Sensor Roller, and Separator O-Rings. (See
paragraph 5-3-9).
- 5. Remove the Processor. (See paragraph 5-3-10-1.)
- 6. Clean the Drum. (See paragraph 5-3-10-2.)
- 7. Clean the Upper and Lower Pressure Roller Assemblies. (See paragraph 5-3-10-3.)
- 8. Clean the Stripper Blade. (See paragraph 5-3-10-4.)
- 9. Replace the Felt Pads. (See paragraph 5-3-10-5.)
- 10. Clean the Ultem Film Guide. (See paragraph 5-3-10-6.)
- 11. Clean the Densitometer. (See paragraph 5-3-10-7.)
- 12. Clean the Processor Entrance and Exit Rollers. (See paragraph 5-3-10-8.)
- 13. Reassemble the Processor components. (See paragraph 5-3-10-9.)
- 14. Check the Stripper gap, and adjust as necessary. (See paragraph 5-3-11.)
- 15. Print a film calibration from the local panel and confirm image quality. (See paragraph 5-3-12.)

Note
After PM cleaning, place the used cleaning pads in a zip lock bag and dispose of them properly.

2001 September Rev. N 1908110 5-3

Service Manual

Table 5-1. PM Procedure Time Intervals

Procedures See Every Every Every Every Every Every

(Perform in order where Para.: 10,000 20,000 30,000 40,000 50,000 60,000
indicated by x in column.) Cycles Cycles Cycles Cycles Cycles Cycles

Power down. Inspect and 5-3-5

Clean Film Tray and Film 5-3-6 x x x x x x
Feed Roller
Clean/Replace Filters: 5-3-7
1. Clean Fan Filter. x x x x x x
2. Replace Charcoal Filter. x x x
3. Replace Faz Filter. x
Clean Laser Scanning Area, 5-3-8 x x x x x x
Capstan, and Pinch Rollers.
Clean Scoop, Film Guide 5-3-9 x x x x x x
Area, 1–2 Sheet Sensor
Roller, and Separator
O-Rings.
Clean Processor:
1. Remove Processer 5-3-10-1 x x x x x x
2. Clean Drum 5-3-10-2 x x x x x x
3. Clean Proc. Rollers 5-3-10-3 x x x x x x
4. Clean Stripper Blade 5-3-10-4 x x x x x x
5. Replace Felt Pads 5-3-10-5 x x x x x x
6. Clean Ultem Film Guide 5-3-10-6 x x x x x x
7. Clean Densitometer 5-3-10-7 x x x x x x
8. Clean Entrance and 5-3-10-8 x x x x x x
Exit Rollers
9. Reassemble Processor 5-3-10-9 x x x x x x
Adjust Stripper gap. 5-3-11 x x x x x x
Print a film cal sheet and 5-3-12 x x x x x x
confirm quality.

Note
PM at 70,000 cycles is the same as at 10,000 cycles, and at 80,000 cycles it is the same as at
20,000 cycles, etc.

5-4 1908110 2001 September Rev. N

Section 5 – Additional Information

5-3-5. System Power Down

! Warning
When the power cord is plugged in, hazardous voltages are present in some areas of the IMAGER.
These voltages can cause severe injury or death.
1. Insert the film saver and remove the film tray.

2. Turn off power and unplug the IMAGER power cord.

5-3-6. Inspecting and Cleaning the Film Tray and Film Feed Roller
Supplies Required
Vacuum cleaner
Low-lint alcohol-saturated wipes (TEXWIPE TX1065)
Protective gloves
Film Tray
1. Vacuum the exterior of the tray (including the black velvet) and then wipe it off with a TX1065 wipe.

Note
If the film needs to be saved, transfer it to a film pouch in a dark room so that the films can be used
after the cleanup procedure.

2. Remove the film saver, film, and the liner from the tray.

3. Inspect the inside of the tray, the ramp and the edge of the ramp for possible scratches. Replace the
tray if there are scratches on the ramp or the top edge of the tray.

4. Wipe off the inside of the tray, the ramp, and the ramp edge with a TX1065 wipe.

Film Feed Roller

1. Inspect the film feed roller (see Figure 5-1). Replace the roller if there is any damage or if it is worn
out.

2. Reach in through the film tray area and clean the feed roller with a TX1065 wipe. Manually rotate the
roller so you can clean the entire surface.

2001 September Rev. N 1908110 5-5

Service Manual

Figure 5-1. Accessing the Film Feed Roller

5-3-7. Cleaning or Replacing Filters

The three machine filters must be cleaned or replaced at the following intervals:
• Fan filter (located on rear of machine) Clean at 10,000 machine cycles
• Charcoal filter (located on processor assembly) Clean at 10,000, replace at 20,000 cycles
• Faz filter (located inside top cover) Clean at 10,000, replace at 60,000 cycles

5-3-7-1. Cleaning the Three Filters (Every 10,000 Cycles)

Supplies Required
Vacuum cleaner
Cleaning Procedure
1. At the rear of the machine, pull off the plastic cover and remove the fan filter.
2. Either vacuum the filter or wash it with warm water.
3. Replace the fan filter and cover.
4. Push the right side button and raise the top cover.
5. Clean and inspect the charcoal and faz filters as follows:
a. Vacuum the exposed surfaces of the two filters.
b. Remove the two filters. (See paragraphs 5-3-7-2 and 5-3-7-3 for removal instructions.)
c. Wipe off the exit ports of the filters.
d. Inspect the filters. Replace them in the machine, or discard them and install new filters, as
necessary.

5-6 1908110 2001 September Rev. N

Section 5 – Additional Information

5-3-7-2. Replacing the Charcoal Filter (Every 20,000 Cycles)

1. Push down with your thumbs on the top corners of the filter and pull out to remove it (see Figure 5-2).
2. Install the new filter in the top cover.

Figure 5-2. Replacing the Charcoal Filter

5-3-7-3. Replacing the Faz Filter (Every 60,000 Cycles)

1. Grasp the end of the faz filter (see Figure 5-3) and pull out to remove it from the processor.
2. Install the new filter.

Figure 5-3. Replacing the Faz Filter

2001 September Rev. N 1908110 5-7

Service Manual

5-3-8. Cleaning the Laser Scanning Area, Capstan, and Pinch Rollers
Supplies Required
Vacuum cleaner
Low-lint alcohol-saturated wipes (TEXWIPE TX1065)
Protective gloves
Procedure
1. Remove three attaching screws and remove laser shield (see Figure 5-4).

2. Clean the laser shield with a TX1065 wipe.

3. Remove the three screws holding the left (as viewed from the machine front) side panel of the imager,
and remove the left side panel.

4. Raise the upper wire guide and vacuum the laser scanning area behind the laser shield area.

5. Use a TX1065 wipe to clean the dust and debris from the capstan and the two pinch rollers. Do this
while slowly rotating the capstan flywheel (which was exposed by removal of the left side panel).

Note
Use a couple of TX1065 wipes to clean the rollers to ensure that no visible extraneous material is left
on the rollers. Do not leave any debris in the gap between the two pinch rollers.

6. Lower the upper wire guide.

7. Replace the laser shield and secure it with the three screws.

4
1

5
Figure 5-4. Cleaning the Laser Entry Area, Capstan, Pinch Rollers and Separator O-Rings

5-8 1908110 2001 September Rev. N

Section 5 – Additional Information

5-3-9. Cleaning the Scoop, Film Guide Area, 1-2 Sheet Sensor Roller, and Separator
O-Rings
Supplies Required
Vacuum cleaner
Low-lint alcohol-saturated wipes (TEXWIPE TX1065)
Protective gloves
Procedure
1. Raise the upper wire guide (see Figure 5-5).

2. Pull down the lower wire guide.

3. Vacuum all the exposed surfaces, including: scoop, scoop cover plate, film tray housing, separator
roller, film entrance guide, etc.

4. Use a TX1065 wipe to wipe all the exposed areas.

5. Access and clean the top end of the scoop as thoroughly as possible.

6. While rotating the top separator roller, clean the separator O-rings with a TX1065 wipe.

7. Rotate and clean any dirt buildup on the 1-2 sheet sensor roller, using a TX1065 wipe.

8. Raise and lock the lower wire guide, and lower and lock the upper wire guide.

The “Scoop” is the area behind

the Lower Wire Guide

Figure 5-5. Cleaning the Scoop, Film Guide Area, 1-2 Sheet Sensor Roller, and Separator O-Rings

5-3-10. Cleaning the Processor

!
Caution

Hot Surface

When the IMAGER is initially powered down, the processor drum and rollers are hot. Take care
when working in the drum and roller area.

2001 September Rev. N 1908110 5-9

Service Manual

5-3-10-1. Removing and Disassembling the Processor for Cleaning

Removing the Processor
1. Remove three screws, and remove the right side panel of the IMAGER (see Figure 5-6). (The left side
panel was removed in paragraph 5-3-8).

Figure 5-6. Removing the Side Panels

2. Disconnect the plugs from P2, P3, and P4 on the CPU PWA (see View A of Figure 5-7).
3. Disconnect the plug from P5 of the power module.
4. Remove two attaching screws from each side of the processor base (see View B of Figure 5-7) and
remove the processor assembly from the machine.
5. After removing the processor assembly, vacuum the exposed area in the imager.

Figure 5-7. Removing the Processor Assembly

5-10 1908110 2001 September Rev. N

Section 5 – Additional Information

Removing the Processor Half

1. Unlatch the processor cover.
2. Remove one attaching screw from each side (see Figure 5-8).
3. Remove the processor half and set it aside for cleaning of the upper pressure rollers (paragraph).

Figure 5-8. Removing the Processor Half

5-3-10-2. Cleaning the Drum

Supplies Required
Isopropyl alcohol
Cleaning cloth (TEXWIPE TX312)
Protective gloves
Procedure

Note
Leave the drum seated in the processor frame while you clean it.

1. Rotate the processor drum wheel on the left side while cleaning the processor drum surface with
alcohol dampened TX312 cleaning cloths.
2. Use multiple wipes to ensure that the drum surface is clean.

3. After cleaning the drum, remove it from the processor frame as follows:

a. Disconnect the ground wire from the right side of the processor assembly (see Figure 5-9).
b. Remove a locking plate from each side of the drum.
c. Manually turn the bearing blocks to align the flats for removal of the drum (see inset in Figure 5-9).
d. Lift the drum from the processor and carefully set it aside.

2001 September Rev. N 1908110 5-11

Service Manual

d c

Figure 5-9. Removing the Drum

5-3-10-3. Cleaning the Upper and Lower Pressure Rollers

Required Supplies
Isopropyl alcohol
Cleaning cloths (TEXWIPE TX312)
All purpose cleaning pads (3M O-Cel-O)
Protective gloves

Note
Leave the upper roller assembly in the processor cover and the lower roller assembly in the
processor frame for cleaning, unless the asemblies show considerable faz accumulation.

Upper Pressure Rollers

1. Inspect the roller assembly and behind the rollers. If these areas show significant faz accumulation,
remove the rollers for cleaning as follows (see Figure 5-10).
a. Remove the grounding clip screw and ground wire (if present) from the lower shaft on the left side.

Note
During reassembly, be sure to securely attach the grounding clip to ensure proper roller grounding.

b. On the right side of the cover, remove the screws (one each shaft) from the ends of the two shafts
securing the roller assembly.
c. Pull the shafts out from the left side.
d. Remove the roller assembly.

!
Caution
To prevent deplating of the rollers, do not rub rub the rollers hard with the abrasive cleaning pads.
2. Clean the metal surfaces behind the rollers using TX312 cleaning cloths and Isopropyl alolchol. Use
alcohol dampened cleaning pads to remove tough stains.

5-12 1908110 2001 September Rev. N

Section 5 – Additional Information

3. If deplating or degradation (such as flat spots) of the rollers is evident, replace them.

d b

a c
Figure 5-10. Removing the Upper Pressure Roller Assembly

Lower Pressure Rollers

1. Inspect the roller assembly and behind the rollers. If these areas show significant faz accumulation,
remove the rollers for cleaning as follows (see Figure 5-11):
a. Remove the grounding clip from the lower shaft on the right side of the processor frame.

Note
During reassembly, be sure to securely attach the grounding clip to ensure proper roller grounding.

b. On the left side of the frame, remove the screws from the two shafts securing the roller assembly.
c. Pull the two shafts out from the right side.
d. Remove the roller asembly.
2. Clean the lower roller assembly using the same procedure as for the upper roller assembly.

c a

Figure 5-11. Removing the Lower Pressure Roller Assembly

2001 September Rev. N 1908110 5-13

Service Manual

5-3-10-4. Cleaning the Stripper Blade

Supplies Required
Isopropyl alcohol
Cleaning cloths TEXWIPE TX312)
All purpose cleaning pads (3M O-Cel-O)
Protective gloves

Procedure

Note
Remove the felt pad(s) from the stripper before cleaning (see paragraph 5-3-10-5) Then clean the
stripper as follows before installing new felt pad(s) in paragraph 5-3-10-5.

!
Caution
The stripper blade is sharp. Take care while cleaning it.

1. Clean the metal surfaces of the stripper blade (top and bottom), using TX312 cleaning cloths and
Isopropyl alcohol (see Figure 5-12).

2. Ensure that all deposits on the bottom of the blade are removed by using an all-purpose cleaning pad.
(If deposits build up they can damage the drum.)

Figure 5-12. Cleaning the Stripper

5-14 1908110 2001 September Rev. N

Section 5 – Additional Information

5-3-10-5. Replacing the Felt Pad Assemblies on the Stripper

1. Remove the two Allen screws securing the upper felt pad assembly (if present).
2. Remove the two stud nuts (15/64 inch) securing the lower felt pad assembly (Figure 5-13).
3. Replace the lower felt pad assembly with a new one. (Note that it is different from the upper pad.)
4. Secure the lower felt pad assembly with the two stud nuts.
5. Replace the upper felt pad (if required) with a new one.
6. Secure the upper felt pad assembly with the two Allen screws.

Figure 5-13. Replacing the Felt Pad Assemblies

2001 September Rev. N 1908110 5-15

Service Manual

5-3-10-6. Cleaning the Ultem Film Guide

Supplies Required
Isopropyl alcohol
Cleaning cloths (TEXWIPE TX312)
All purpose cleaning pads (3M O-Cel-O)
Protective gloves

Procedure
1. Remove two shoulder screws and remove the Ultem film guide (see Figure 5-14).
2. If the guide can be separated, separate it before cleaning.
3. Wipe the film guide clean with alcohol and TX312 cleaning cloths or all-purpose cleaning pads.
4. Replace the film guide and secure it with the two shoulder screws.

Note
The shoulder screw heads must face down during assembly.

Figure 5-14. Cleaning the Ultem Film Guide

5-16 1908110 2001 September Rev. N

Section 5 – Additional Information

5-3-10-7. Cleaning the Densitometer

Supplies Required
Isopropyl alcohol
Cleaning cloths (TEXWIPE TX312))
Pre-soaked alcohol pad (TEXWIPE TX801)
Protective gloves

Procedure
1. Remove two attaching screws and remove the cover plate (see Figure 5-15).
2. Unplug the inline connector for the processor exit sensor.
3. Remove the vertically aligned screws from each end, and remove the densitometer assembly from the
processor housing.
4. Remove the horizontally aligned screws and separate the mounting plates of the densitometer
assembly. (Take care not to lose the spacer bars, if present.)

!
Caution
Be very gentle with the delicate lens surface while cleaning the sensor lens in the next step. Also
take care not to damage the delicate processor exit sensor.

5. Clean the inside surfaces of the mounting plates with alcohol and TX312 cleaning cloths. Clean the
sensor lens on the upper plate with a pre-soaked alcohol pad. Be very gentle with the delicate lens
surface, and be very careful not to damage the processor exit sensor.
6. Remove two attaching screws and remove the plastic housing for the densitometer light source.
7. Clean the glass lens on the housing with a pre-soaked alcohol pad.
8. Reinstall the light source housing with the lens flush against the lower plate (see Figure 5-15).
9. Reassemble the densitometer assembly. Make sure that you align the two spacer plates properly. Also
make sure that the actuator arm of the processor exit sensor is in the slot.
10. Install the densitometer assembly in the processor housing, and reconnect the inline plug for the exit
sensor.

Figure 5-15. Cleaning the Densitometer

2001 September Rev. N 1908110 5-17

Service Manual

5-3-10-8. Cleaning the Entrance and Exit Rollers

Supplies Required
Isopropyl alcohol
Cleaning cloths (TEXWIPE TX312)
Protective gloves

Procedure
1. Use alcohol and TX312 cleaning cloths to wipe clean the two exit rollers (one steel and one rubber).
Rotate the rollers to gain access to all surfaces (see Figure 5-16).
2. Remove four attaching screws (or nuts) and remove the two film entrance guides (see Figure 5-16).

!
Caution
Take care while cleaning the entrance rollers that you no not contact the entrance sensor. This
sensor is delicate and easily damaged.

3. Use alcohol and TX312 cleaning cloths to clean the two entrance rollers as you rotate them.

Note
If either rubber roller (entrance or exit) is hard and glazed, even after cleaning, replace it.

4. Replace the film entrance guides, being sure not to overtighten the attaching hardware.
(Overtightening will cause the guides to bow and restrict film movement.)

Caution:
Do not damage
delicate Processor
Entrance Sensor

8600/8610
–169C

Figure 5-16. Cleaning the Processor Entrance and Exit Rollers

5-18 1908110 2001 September Rev. N

Section 5 – Additional Information

5-3-10-9. Reassembling the Processor

1. Replace the lower pressure roller assembly in the processor housing (if it was removed during
cleaning). Refer to paragraph 5-3-10-3. Reassembly is the reverse of disassembly. Make sure the
grounding clip is making good contact with the screw.
2. Replace the upper pressure roller assembly in the processor half cover (if it was removed during
cleaning). Refer to paragraph 5-3-10-3. Make sure the grounding clip is making good contact with the
screw.
3. Replace the drum in the processor. Refer to paragraph 5-3-10-2.
4. Replace the processor half on the processor. Refer to paragraph 5-3-10-1.
5. Replace the processor assembly in the machine. Refer to paragraph 5-3-10-1.

5-3-11. Adjusting the Stripper Gap

Note
After the stripper has been cleaned and the felt pads replaced, the stripper gap must be checked,
and adjusted if necessary. If the gap is too narrow, drum damage can occur. It it is too wide, jams will
occur.

Specification
Gap of 0.005 + 0.001 inch between drum and stripper

Tools Required
Feeler gauges (0.004 and 0.006 inch)
3/32 inch ball head driver
Check
1. Open the processor cover.

Note
When you make the gap checks, the rollers on each side of the stripper assembly must be in contact
with the drum. Hold the stripper assembly down while checking with the feeler gauge, so you don’t
inadvertently lift it during the checks.

2. Try to slide a 0.004 inch feeler gauge between the stripper and the drum down the length of the
stripper (see Figure 5-17). If the gauge does not fit, the gap is too small. Perform the adjustment (see
next page).
3. Try to slide a 0.006 inch feeler gauge between the stripper and the drum. If the gauge fits, the gap is
too large. Perform the adjustment (see next page).

2001 September Rev. N 1908110 5-19

Service Manual

Figure 5-17. Measuring the Stripper Gap

Adjustment for Two-Pad Stripper

1. Use a 3/32 inch Allen head ball driver to adjust the Allen screw (see Figure 5-18) on the roller
assembly. Turn the Allen screw clockwise to decrease the gap or counterclockwise to increase it.
2. Measure the gap and adjust as necessary.
3. Perform the adjustment on both roller assemblies until the gap is within specification.

Figure 5-18. Adjusting a Two-Pad Stripper

5-3-12. Printing a Film Calibration Sheet and Checking Print Quality

1. After checking that the machine is fully reassembled, plug in the power cord.
2. Apply power to the machine and allow it to warm up.
3. Print a film calibration sheet and check quality of the print.
4. Record the PM call in the Service History.

5-20 1908110 2001 September Rev. N

Section 5 – Additional Information

5-4. Configuring the Memory Setting (Memory Management)

Image memory (RAM) can range from 3.75 MB (4 meg) to 31.75 MB (32 meg) by use of any combination
of 4, 8, or 16 MB SIMMs in the two SIMMs sockets. The memory setting for each input is configured by
using information that is specific to each installation site, while providing the IMAGER with enough RAM
to store two films at once.
Example: The following formula would determine the image RAM:
image size X format X number of films = memory needed.
If a client prints 640 X 480 images in a 6:1 format, the formula would be:
640 X 480 X 6 X 2 = 3.6 Megabytes.
For DICOM, the number of clients must be factored into the formula. If six users are connected to
DICOM, the formula becomes:
image size X format X number of films X number of clients = total memory needed,
640 X 480 X 6 X 2 X 6 = 22.2 Megabytes.
Typical minimum memory configurations are:
Analog - 7.75 Mb (8 Meg)
Digital - 7.75 Mb (8 Meg)
Network - 15.75 (16 Meg)
SCSI - 4 Mb only

5-5. Olympus 230 Mb M/O Drive Jumper Settings

The first three pins of the dual inline jumper connector define the SCSI ID address of the drive in a binary
format:

Pin No. Binary Value

1 1
2 2
3 4

Typical SCSI address for an internal drive used in the IMAGER is 6, so pins 2 and 3 have jumpers on.
The following is a chart of the remaining dual inline jumper connector pin locations and whether each
jumper is on (connected) or off for the typical factory setting. The two most important factory settings that
should never be changed are for pins 4 and 10, which represent grounds and should always have their
jumpers on.

Pin No. Function and Description Jumper Factory

Setting
4 Ground - Do not remove. On
5 Reserved - Do not connect Off
6 SCSI Type - On = SCSI 1; Off = SCSI 2 Off
7 Parity checking - On = No parity check; Off = Parity check Off
8 Host CPU - On = Apple MAC; Off = Any other PC host Off
9 Termination - On = No termination; Off = Termination in place Off
10 Ground - Do not remove On

2001 September Rev. N 1908110 5-21

Service Manual

The following two single-pin locations are connectors for an external Busy LED, if used. The IMAGER
does not have a remote Busy LED, so no connections are required, and they should never be shorted
together.
11 Busy LED Signal - No connection
12 +5 VDC for Busy LED - No connection

Figure 5-19.

5-6. Olympus 540 Mb M/O Drive Switch Settings

The first three switch positions of Switch 1 (see Figure 5-3) select the SCSI ID number, as shown in the
table below. For example, to set the SCSI ID to 1: Set SW1-01 to OFF, SW1-02 to OFF, and SW1-03 to
ON.

SCSI ID SW1-01 SW1-02 SW1-03

0 (default) OFF OFF OFF
1 OFF OFF ON
2 OFF ON OFF
3 OFF ON ON
4 ON OFF OFF
5 ON OFF ON
6 ON ON OFF
7 ON ON ON

5-22 1908110 2001 September Rev. N

Section 5 – Additional Information

Figure 5-20.

5-7. ATL HDI M/O Print Setup

The HDI 1000, 3000, and 5000 can write on 3.5 M/O disks using the DEFF format. Use the following
procedure to change the M/O disk parameters on each of the ATL HDI Ultrasounds:
1. Press the SETUPS key to access the Setups Options Directory.
2. For HDI 3000 software version 38.15 or lower, select the Access Link Directory.
For HDI 3000 software version 39.08 or higher, select the Image Management Directory.
For HDI 5000, select the Image Management Directory.
3. Open the Printers Menu and select printer parameters:
a. Optical disk user no. = 1 for HDI 1000
= 2 for HDI 3000
= 3 for HDI 5000
b. B & W film format = 2x3
c. Color film format = 2x3
d. Printed image dest. = All to B&W printer
4. Close the Printers Menu.

Note
Some Demo Vans may carry all three HDI Ultrasound models. You must set the parameters for each
user number in the IMAGER to match each HDI model number as described in step 3 above. If
Autoprint is set ON for User 1 in the IMAGER and OFF for all other users, you will not be able to
autoprint if you insert a disk from the HDI 5000.

5-8. ATL HDI 3000/5000 Video Calibration Test Patterns

When you are doing a video calibration on an ATL HDI 3000/5000, it is useful to access video test
patterns. Use the following procedure to access applicable video test patterns:
1. Press the SETUPS key.
2. Use the roller ball to highlight the DIAGNOSTICS box in the lower left corner. Then select it.
3. Highlight and select VIDEO TEST PATTERNS UTILITY.
4. Highlight the START box and select OK.
5. Use the space bar to scroll through the test patterns.
6. Select the desired test patterns and exit when finished.

2001 September Rev. N 1908110 5-23

Service Manual

5-9. Adapter Cable Pinouts

Figure 5-21 through Figure 5-23 provide the pinouts for the various host adapter cables that can be
connected to the IMAGER.

RS422 Host Adapter Cable

(78-8077-4159-6)

37 Pin 9 Pin Signal

1 1 GND
21 2 RXD+
3 7 RXD–
20 3 TXD+
2 8 TXD–
4
5
8
9
22
23
26
27

Figure 5-21.

RS232 Host Adapter Cable

(78-8071-8331-0)

25 Pin 9 Pin Signal

2 4 TX
3 6 RX
7 1 GND
6
8
20
4
5

Figure 5-22.

Genesis Cable (GE only)

25 Pin 9 Pin Signal

1 1 GND
9 2 RXD+
8 3 TXD+
22 7 RXD–
21 8 TXD–

Figure 5-23.

5-24 1908110 2001 September Rev. N

Section 5 – Additional Information

5-10. IMAGER Firmware Enhancement Revisions

Version 4.6 (Effective 6/30/99, beginning with Serial Number 1900)
False Processor Drum Related Error Codes (EC 17, 19, 88) have been eliminated.
Configure Client Defaults Sub-Menu item was restored (was lost as a bug in Version 4.5).
An FAI Response Will Be Sent to Host when CLI fails, but an ALM 61 will no longer be sent.
See also the Version 4.5 entry below.
Version 4.5
(There is a bug in this version, so it was never officially released. All of the following features have been
added to Version 4.6, with the bug corrected.)
Calibration Sheet Now Rebuilt in Memory each time it is printed so any corruption is cleared.
Ethernet Default Router Address is now an Ethernet installation menu item.
SCSI Target Now Reports Sense Data for errors that are related to only that target modality.
The False “Unable to Read DIR Entry” Bernoulli Disk Error is now eliminated.
The Laser Will No Longer Become Stuck in “Regulating Temperature.”
SCSI Target Mode No Longer Implements Optional “FRU” which is a sense data field.
Host Control RES Command will now cancel any unprinted contrast test requested by CNT.
SCSI Target Mode Displays Contrast & Density in System Configuration of the Test Menu.
“Input B Image too Large to Print” displayed if SCSI disk image is too large by pixels, etc.
SCSI Target Mode Will Now Print Entire Image, including the last line pixel and last image line.
Image DRAM Diagnostic Now Correctly Counts number of bad blocks of image memory.
Setting a Suspended Modality Back to Ready now prevented by completion of acquisition.
Duplicated Code for ATL and Bernoulli disk formats has been eliminated.
A Power On Self Test is Now Performed on the local buffer used to pass data to the ASIC.
A Magnification Factor of Less than 1.0 will never be applied to an AEGIS that is too large.
AIM Command from Ethernet Software will no longer be rejected by the system software.
SCSI Initiator Image Pixel and Line Replication now correct, resulting in printing whole image.
“Lamp Failed to Reach Temperature” Error now gives more brightness information to service port.
“Trailing Blank Images” is Recognized as a host control film with no visible images ignored.
Processing of the Host Reset (RES) Command will flush output queue of any old responses.
Software Has Been Modified to Acknowledge (ACK/NAK) host commands more quickly.
Comma or Space can be selected in Serial Protocol install menu for host response delimiter.
False Multiple Sheet errors are eliminated when the 2-sheet switch is activated momentarily.
“Insert Film Tray or Remove Empty Tray” added as action for “Unable to Unlock Film Tray.”

2001 September Rev. N 1908110 5-25

Service Manual

Version 4.4 (Effective 12/2/98, beginning with Serial number 1770.)

A Check Condition Status is Returned when a second SCSI target Print command is received.
Formatting of Error Return Address in Debug Data (Control D) has been corrected.
Acquiring is Displayed on the Local Panel when receiving image as an IMAGER SCSI Target.
SCSI Target Software Displays Error when image is too large to print for format selected.
SCSI Target Software Now Uses Last Fully Acquired Image in Memory for contrast test.
SCSI Target Software Now Removes Contrast Test progress display when an error occurs.
Energy Saver is Now Set to OFF as the factory default.
ARS Now Sent to the Host when 8300 is Put On-line after error (such as “film out”) is corrected.
Film Calibration is Printed if a Print is Requested and a film has not been printed in 8 hours.
Input B DMA Failure Error Code has been assigned EC 74.
Remove, Load, and Insert Film Tray (30) now displayed when empty film tray is not ejected.
Version 4.3 (Never released to production)
NVRAM Configuration Parameters are returned to the initiator when IMAGER is a SCSI Target.
IMAGER Will Wake Up from Energy Saver while in SCSI Target Mode when command is received.
Intermittent System Crashing Corrected by modifying more ISRs to use separate stack.
SHO Command Was Added to Host Control Software and now responds with PRT 2.
Version 4.2 (Effective 5/8/98 beginning with Serial Number 1566.)
Retransmission Requested From Digital Modality if error is detected or receipt of data.
Parity Errors Can Be Detected Only With Odd Parity because of a hardware limitation.
A SCSI Disk Can Be Ejected From Its Drive by pressing the drive eject button.
Unique Numeric Code Has Been Assigned for each error message displayed on front panel.
Colors Are No Longer Garbled when printed on Sony 7000/8800 from DEFF formatted disks.
Image Memory Full Error Message is now displayed when SCSI modality’s DRAM is full.
Black and White Video Offsets are now manually adjustable for a difference of up to 5%.
“Schedule PM” Message is displayed when 10,000 films have been printed since last reset.
Modality Groups Added so that 1 of up to 11 groups of user LUTs can be service selectable.
Non–monotonic Exposure Values after smoothing of calibration data will fail the film cal.
IMAGER No Longer Locks Up when printing write enabled RDOS formatted disks.
Floating Point & Integer Magnification in both decimal & hex accepted by DZO command.
Software Downloaded Checks For Correct Address before reprogramming flash EPROMs.
Software Downloaded Checks Imager to ensure correct IMAGER software is downloaded.
Calibration Software Rewritten to smooth D log E data then is interpolated with cubic spline.
Printed Calibration Wedge Film Modified to have 1 inch border at top & half inch at bottom.
Intermittent System Crashing Corrected by removing all system traps from board ISRs.

5-26 1908110 2001 September Rev. N

Section 5 – Additional Information

Version 4.1.1 (Never released to production)

Error Log Increments Total Number of errors beyond 50 but last 50 errors are displayed.
Film Now Calibrated After Waking from Energy Saver instead of 24 hours since last cal.
Audible Alerts on Keypad are once for a successful acquisition and three times for an error.
Film Format Based on Zones defined in the DZO command(s) instead of best fit format.
SCSI Target Debug statements have been added and can be observed with CTRL D.
Cubic Spline Interpolation is now used before generating the gamma table linearly.
Cubic Spline Data and 20 Cal Bands p-value ULUT) and exposure can be observed with CTRL D.
New Convolution Kernels are being used that sum to 16384.
Version 4.1 ( Effective 7/18/97, beginning with Serial Number 1291)
SCSI Target Mode operates correctly when a reset is sent from a rebooted host PC.
SCSI Code Was Cleaned up to present test software from being compiled in production.
Film Density Drift Reduced by super heating and “Regulating Temp” after warm up.
Densitometer Lamp Calibration done before each film cal & failure reported after 3rd failure.
SCSI Disk Installed Menu Displays for 2nd SCSI device after exiting 1st menus if Autoprint off.
SONY Color Printer Errors caused by other tasks & incorrectly reported are now eliminated.
SCSI Disk Eject Instructions are displayed when operator exits SCSI menu without printing.
Digital Acquisition Timeout is now 60 seconds of no activity on the digital modality line.
SCSI Color Only Disks will now print correctly even if no black and white images are on disk.
Narrow Film Calibration Bands previously interpreted as 2 bands is now be seen as 1 band.
Software Continuous Improvement was implemented to provide a more flexible baseline.
Host Control MSZ Command now okay for IMAGER and will respond with PAS 0810 0810 0810.
Version 4.06
Response to Host Control RQS Command is a STA 1 RDY. No additional status info.
Response to Invalid Host Control Command is INV followed by echoing bad command.
Host Control Memory Overflow FAI BSY instead of FAI MOV, PTF BSY instead of PTF MOV.
Host Control DZO with Blank Images permits host to specify contrast table of B for blank out.
Host Control PTY Command is responded to by the IMAGER with PAS IMAGER
Host Control SVS ON Command enables sequential annotation, starting at 1, until SVS OFF.
AEGIS Disk Error Processing to blank out portions of the image data when disk read errors.
ATL Disk Error Processing to blank out portions of the image data when disk read errors.
ATL Disk Sector Boundary Processing of image data that starts on exact disk sector boundary.
Bernoulli Disk Completion allows other disks to be printed even if Bernoulli isn’t removed.
SCSI Color Printer Out Of Paper is reported and waiting image is printed when paper is put in.

2001 September Rev. N 1908110 5-27

Service Manual

SCSI Color Film Status Display now indicates which color film number is printing.
SCSI Sony 8800 Color Printer LCD display message goes to Ready if print is aborted at IMAGER.
Film Density Drift Reduced by adding five minutes to the warmup cycle to stabilize temp.
Empty Film Tray Insertion no longer attempts to feed film from empty tray to do auto film cal.
Energy Saver Activation While Printing will not happen until 3 hours after all printing is done.
Software Version Info Sent to Service Port when Control D is sent from a PC or modem.
Version 4.05
SCSI Error Reading Large Files large reads are broken down to a series of small operations.
Menu Numbering on Last Exam Selection was corrected so it no longer changes with Enter.
Version 4.04
Sony 8800 Color Printer can now be printed to via the SCSI Input Module of the IMAGER.
SCSI Color Image Forma can be 1:1, 2:1, 4:1, or 6:1 on the Sony 7000 or 8800 Printers.
SCSI Color Image Scaling to fit within the format when printed on the 7000 or 8800 Printers.
SCSI Bus Errors eliminated when caused by unexpected responses from hardware.
SCSI Color Film Selection can be made separately from black and white films.
SCSI Color Images Printed After Black and White on IMAGER when there’s no color printer.
SCSI Color Options like format and number to print will be used by IMAGER in black & white.
SCSI Contrast Prints use density, layout, aspect ratio, polarity & smoothness set by user.
SCSI AH/Emulsion viewing setting defined in installation menu will be used to print films.
SCSI Print Aspect Ratio was renamed from just Aspect Ratio.
SCSI User Number and Parameters was renamed from just User Number.
SCSI Autoprint Default Changed to OFF to allow viewing of user number of the first image.
SCSI User (Number) ID Displayed of the first image on disk when Enter is pressed.
NIS (Network Interface Software) Firmware Version Number displayable on local panel.
Network Client Configurable Defaults like Polarity, Async Status, Warning Status added.
Ethernet Menus changed order of items or moved from Installation menu to User Setup.
Ethernet Contrast Test selected from local panel sends host control command from DMCS.
Host Control Status Response has been changed to return STA 1 RDY for RQS command.
Host Control ALM 72 is not resent until 3 invalid commands are received after CLA & RES.
Version 4.03
Video Calibration Image Area has been implemented to allow area selection for calibration.

5-28 1908110 2001 September Rev. N

Section 5 – Additional Information

Version 4.02
Video Interface Vertical Delay is now entered on a field basis rather than a frame basis.
Video Interface Even/Odd Start Line interpretation was reversed so that Odd is the default.
Video Interface Clocks Per Line changed from Pixels/Line & now listed before Horiz. Active.
SCSI Color Film Selection allows selecting which color prints print on attached color printer.
Host Control DZO Enlargement Modeconverts any Sharp/Smooth greater than 6 to Auto.
Network Interface Contrast Tables use inverse polarity for received table numbers = 13–24.
Additional SCSI Disks Supported by IMAGER includes AEGIS 2.0, AEGIS 2.4 and GE DEFF.
SCSI AEGIS Color Images Printed can now be printed on the Sony 7000 Color Printer.
Marking SCSI AEGIS Images Printed so that once printed they can’t be reprinted as “new”.
SCSI Print Aspect Ratio can now be defined by user number for the printed image.
SCSI Last Pixel and Line Replicated to compensate for the print ASIC not printing these.
Calibration Negative Transmittance Ignored so last positive value used to calculate DMAX.

2001 September Rev. N 1908110 5-29

Service Manual

5-11. Installation Menus

Analog Menu
1. Aspect Ratio 1. Measured End Zone Reading
2. Video Interface 13. Energy Saver Option
1. Pixel Clock 14. Image Viewing
2. Clocks per Line 17. PM Exposures (eff. V. 4.2)
3. Horizontal Active
4. Horizontal Delay Digital Menu
5. Vertical Active 1. Aspect Ratio
6. Vertical Delay 3. Serial Control Interface
7. Interlace 1. Baud Rate
8. External Clock 2. Number of Data Bits
9. Clock Delay 3. Number of Stop Bits
10. Start/Frame 4. Parity
11. Perform Video Calibration 5. Delimiter (between Host Control Commands) (eff. V. 4.6)
1. Start Point Percentage Comma
2. End Point Percentage Space
3. Start Calibration 6. Protocol
12. Black Level Offset 6. Mark Install Date
13. White Level Offset 7. Memory Management
14. 750 x 480 (Acuson 128) 8. Calibration Enable
15. 640 x 480 (ATL) 9. Module ID
16. 580 x 480 (ATL) 10. Exposures
3. Serial Control Interface 11. Cal Processor Center Temp
1. Baud Rate 1. Measured Center Zone Reading
2. Number of Bits 12. Cal Processor End Temp
3. Number of Stop Bits 1. Measured End Zone Reading
4. Parity 13. Energy Saver Option
5. Delimiter 14. Image Viewing
6. Protocol (3M host or keypad) 15. Digital Interface
6. Mark Install Date 1. Parity
7. Memory Management 16. Modality Group (eff. V. 4.2)
8. Calibration Enable 17. PM Exposures (eff. V. 4.2)
9. Module ID
10. Exposures Network Menu
11. Cal Processor Center Temp 1. Aspect Ratio
1. Measured Center Zone Reading 2. Network Interface
12. Cal Processor End Temp 1. ADDR
1. Measured End Zone Reading 2. IP Address Source
13. Energy Saver Option 3. IP ADDR
14. Image Viewing 4. Net Mask
16. Modality Group (eff. V. 4.2) 5. Connector
17. PM Exposures (eff. V. 4.2) 6. Router (eff. V. 4.6)
7. Configure Client Defaults
SCSI Menu
1. Modality Groups
1. Aspect Ratio 2. Asynchronous Status
5. SCSI Interface 3. Warnings
1. SCSI Role 6. Mark Install Date
2. SCSI Unit ID 7. Memory Management
3. SCSI Bus Termination 8. Calibration Enable
4. Configure User Defaults 9. Module ID
User X, Modality Group X (eff. V. 4.2) 10. Exposures
6. Mark Install Date 11. Cal Processor Center Temp
7. Memory Management 1. Measured Center Zone Reading
8. Calibration Enable 12. Cal Processor End Temp
9. Module ID 1. Measured End Zone Reading
10. Exposures 13. Energy Saver Option
11. Cal Processor Center Temp 14. Image Viewing
1. Measured Center Zone Reading 17. PM Exposures (eff. V. 4.2)
12. Cal Processor End Temp

5-30 1908110 2001 September Rev. N

Section 5 – Additional Information

5-12. General Setup Menus Digital, Analog, SCSI Target Setup

1. Density
SCSI Initiator Setup (Disk Not in Drive) 2. Contrast
1. User Number and Parameter 3. Print Contrast Samples
1. Number B&W Copies 4. Sharp/Smooth
2. Number Color Copies 5. Polarity
3. Density 6. Number of Copies
4. Contrast 7. Autoprint
5. Sharp/Smooth 8. Film Layout
6. Polarity 1. Format
7. Print Option 2. Mode
8. B&W Format 9. Keypad Format
9. Color Format 10. Audible Alarm
10. Film Layout 11. Exposure Index
1. Format 12. Perform Calibration
2. Mode 13. Date/Time
11. Film Numbering Network Setup
12. Autoprint
13. Print Aspect Ratio 1. Configure Client Defaults
2. Exposure Index 1. Density
3. Perform Calibration 2. Contrast
4. Date/Time 3. Request Contrast Samples
4. Sharp/Smooth
SCSI Initiator Setup (AEGIS Uninitialized) 5. Polarity
1. User Number 2. Exposure Index
2. Print Contrast Samples 3. Perform Calibration
3. Contrast 4. Date/Time

SCSI Initiator Setup (Disk In Drive with Autoprint 5-13. Test Menus
OFF, Initialized, AEGIS Format or Another
Acceptable Format) Operator Menu
1. First Exam Number to Print 1. System Diagnostic Test
2. First Film to Print B&W=Color 2. Print SMPTE Pattern (4:1)
3. Last Exam Number to Print 3. Keypad Test
4. Last Film to Print B&W=Color 4. Display Software Versions
5. Ready to Print Enter: Imager Firmware
6. User Number Down Arrow: VRTX32 1.0.8
1. Number B&W Films Down Arrow: Contrast Tables 1.0
2. Number of Color Copies Down Arrow: Convolution Kernel 1.0
3. Density 5. Display System Configuration
4. Print Contrast Samples 1. DRAM
5. Contrast 2. Contrast
6. Sharp/Smooth 3. Density
7. Polarity 4. Convolution
8. Print Option 5. Copies
9. B&W Format 6. User’s ID
10. Color Format 7. Protocol
11. Film Layout 8. Modality
1. Format
2. Mode Service Menu
12. Film Numbering 1. Examine System Error Log
13. Aspect Ratio 2. Perform System Diagnostic Test
7. Reinitialize AEGIS Station ID (AEGIS Only) 3. Perform Stored Pattern Test
1. User Number 1. Module
2. Print Contrast Samples 2. Format
3. Contrast 3. Print Mode
4. Pattern
4. Perform Checksum Test
5. Perform Transport Test
6. Perform DRAM Test
7. Service Port Baud Rate

2001 September Rev. N 1908110 5-31

Service Manual

BLANK PAGE

5-32 1908110 2001 September Rev. N

Section 6 – Theory of Operation

6-1. Theory Flowcharts

Figure 6-1. Power-On Initialization

Figure 6-16. Monitor Feed Completion

2001 March Rev. M 1908110 6-17

Service Manual

6-2. 8300 IMAGER Film Feed Timeline

The time chart in Figure 6-17 shows the approximate timing sequence of successive sheets of film fed
through the 8300 IMAGER. Timing is charted with respect to the actuation of film detection switches in the
system.

Figure 6-17. Film Feed Timing

6-18 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-1. Testing
Troubleshooting can be performed by using Local Panel Tests or Computer Tests. The Computer Tests
can be run either locally or from a remote location.

7-1-1. Local Panel Testing

1. Enter the Local Panel Test Menu as follows:
a. Press TEST.
b. Key in 911, and then press ENTER to view the first item in a series of menu items.
2. Refer to Table 7-1 for the sequence of Local Panel Tests.
Table 7-1. Menu Items for Local Panel Tests
Menu Display Options/Actions
1. EXAMINE SYSTEM ERROR LOG
ENTER TO VIEW OR ARROW FOR OTHER
ITEMS
INSTALL DATE TIME TODAY’S DATE
EXPOSURES: TOTAL ERRORS:
DATE TIME COUNT: #: A 01 In #, the A stands for module and can be A or B.
The 01 represents the count of accumulated
CALIBRATION FAILURE (69)
errors.
2. PERFORM SYSTEM DIAGNOSTIC TEST The test runs until completed.
ENTER TO START OR ARROW FOR OTHER
ITEMS
3. PERFORM STORED PATTERN TEST
ENTER TO SETUP OR ARROW FOR OTHER
ITEMS
MODULE = A
ENTER TO CHANGE OR ARROW FOR
OTHER ITEMS
1. MODULE = A Toggles between modules A and B.
TO CHANGE PRESS ARROW, THEN
ENTER
2. FORMAT = 2 ON 1 The selections are : 1 on 1
2 on 1
ENTER TO CHANGE OR ARROW FOR
4 on 1
OTHER ITEMS
6 on 1
2. FORMAT = 2 ON 1
TO CHANGE PRESS ARROW, THEN
ENTER

2001 March Rev. M 1908110 7-1

Service Manual

Menu Display Options/Actions

3. PRINT MODE = SINGLE Toggles between Single or Continuous
ENTER TO CHANGE OR ARROW FOR
OTHER ITEMS
3. PRINT MODE = SINGLE
TO CHANGE PRESS ARROW, THEN
ENTER
4. PATTERN = SMPTE The selections are: SMPTE
Vertical Wedge
ENTER TO CHANGE OR PRESS ARROW
Horizontal Wedge
FOR OTHER ITEMS
4. PATTERN = SMPTE
TO CHANGE PRESS ARROW, THEN
ENTER
5. PATTERN = SMPTE
ENTER TO START OR PRESS ARROW
FOR OTHER ITEMS
4. PERFORM CHECKSUM TEST If the IMAGER fails the test, an error is displayed.
ENTER TO START OR PRESS ARROW FOR
OTHER ITEMS
5. PERFORM TRANSPORT TEST This test serves two functions by showing
actuation of the sensors and running film without
ENTER TO START, PRESS ARROW FOR
exposing it. The film should be clear when it exits.
OTHER ITEMS
If not clear, one or more of the following conditions
may have caused the problem: exposed, fogged,
or aged film, or exposure from light leaks.
Remember that the IMAGER feeds film
continuously during this test.
5. A=1 B=0 C=0 D=1 E=0 F=0 G=0 H=0 0 = OFF
1 = ON
A = Film Tray In Place Switch
B = Film Saver In Place Switch
C = Film Out Switch
D = One Sheet Sensor
E = Two Sheet Sensor
F = Capstan Media Sense Switch
G = Processor Entrance Sensor
H = Processor Exit Sensor

7-2 1908110 2001 March Rev. M

Section 7 – Troubleshooting

Menu Display Options/Actions

6. PERFORM DRAM TEST Remember that the DRAM Test will continue to run
until Exit is pressed.
ENTER TO START, PRESS ARROW FOR
OTHER ITEMS
7. SERVICE PORT BAUD RATE = 38,400 The selections are: 1,200
2,400
ENTER TO START, PRESS ARROW FOR
4,800
OTHER ITEMS
9,600
19,200
38,400

7-1-2. Computer Testing

Running tests with the computer can be done on-site or from a remote location. Computer testing
provides access to the error log, which is the same as the Local Panel error log. It also allows running the
Debug (CTRL D) feature, which displays film calibration results.

7-1-2-1. PC Setup for Windows 95/98

1. Attach a PC to the Serial Service Port of the IMAGER with a straight-through cable and a null modem
adapter. If an AFHU cable is used, the cover interlock is defeated as well.
2. Power on the PC, and launch Hyperterminal.EXE, usually located in the Accessories section of
Programs.
3. Pull down File Menu and select New Connection.
4. Give the connection a name, then press OK.
5. When the Phone Number window comes up, go to the Connect Using box, and select Direct to Com
1, then OK.
6. Set the Port Settings in the Com 1 properties window:
a. Bits per second . . . . . . . . . . . . . . . . . . 38,400
b. Data bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
c. Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . None
d. Stop bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
e. Flow control . . . . . . . . . . . . . . . . . . . Xon/Xoff
Then press OK.

2001 March Rev. M 1908110 7-3

Service Manual

7-1-2-2. Monitoring Commands

Table 7-2. Monitoring Commands

@ command To display error log.

CTRL D To debug.
CTRL E, ENTER To monitor Dicom commands.
CTRL F To echo Local Panel.
AtoDon/AtoDoff To monitor drum temp control.

1. The @ command displays the error log which is the same as the Local Panel Error Log. See
Table 7-1.
2. Pressing CTRL D initiates the Debug feature. If a SMPTE pattern or Image is printed, CTRL D
monitors the film movement. If a calibration is selected, CTRL D tracks film movement and displays
density of the bands of the film cal sheet.
3. Pressing CTRL F displays on the PC monitor whatever is being displayed on the Local Panel.
4. Pressing CTRL E, ENTER allows monitoring the Dicom commands when the Network Input Module is
installed. Press CTRL E, ENTER again to toggle off. (Be sure CTRL D Debug is toggled off before
using this command.)
5. Typing AtoDon will provide drum temperature control information every second. If there is a deviation
from the expected temperature stability, the local panel will beep and the temperature measurement
will be displayed on the PC display. Typing AtoDoff will discontinue the monitoring.

7-1-3. DICOM Troubleshooting with Ethernet (Control E) Debug Menus

Connect a PC to the serial service port of the IMAGER and launch Hyperterminal. With the PC
communicating to the IMAGER, type CTRL E, followed by ENTER. System debug (CTRL D) needs to be
off. The following main menu will appear on your PC from an IMAGER that has network software NIS 3.3:
Debug Menu
1. Print High Level DICOM trace
2. Print Low Level DICOM trace
3. Print 952 trace
4. Turn off DICOM trace
5. Display Ethernet nvram contents
99. Exit Debug Menu
else ’route, ping, netstat, ifconfig, help’
Enter Selection:

7-4 1908110 2001 March Rev. M

Section 7 – Troubleshooting

High Level DICOM trace will provide a readable summary of all DICOM communications between the
IMAGER and its clients.

Note
Supported parameters and responses are documented in the DICOM conformance statement for the
8300 IMAGER.

Low Level DICOM trace will provide a raw hex dump of all DICOM communications between the
IMAGER and its clients.
952 trace provides communications between the IMAGER’s Network PWA and the CPU PWA (which is
the way the IMAGER communicates internally), when DICOM communication is occurring between the
IMAGER and its clients.
Turn off DICOM trace disables any of the three trace functions.
Display Ethernet nvram contents shows the parameters for each client that has been configured on the
IMAGER.
route is used to configure the default router setting of the IMAGER which allows it to communicate with
clients outside its own subnet.
ping helps determine if the IMAGER is properly configured to communicate with clients. You can ping
clients to determine communications are possible and there is a good network hardware connection.
netstat is used to display the IMAGER routing table and current network connections.
ifconfig is used to temporarily change the IMAGER netmask and ip address.
help provides a short description of the route, ping, netstat and ifconfig commands.

The following is an example of what is displayed when help is entered:

Enter Selection: help
SNX Command Help
Add default router:
route add default <gateway ip address> 1
Remove router entry:
route delete <destination ip address>
<gateway ip address>
Display Routing Table:
netstat –nr
Ping network device:
ping –n <device ip address>
Display network ports in use:
netstat –na
Temporarily change ip address:
ifconfig lg0 inet <new ip address>
Temporarily change netmask:
ifconfig lg0 inet netmask <new netmask>

The following is an example of the procedure for the addition of a default router:
Enter Selection: route add default 163.228.152.1
Default router <163.228.152.1> saved to nvram
usage: add destination gateway metric
(metric of 0 if gateway is this host)

2001 March Rev. M 1908110 7-5

Service Manual

The following is an example of a High Level DICOM Trace (explanations in parentheses):

Debug Menu
1. Print High Level DICOM trace
2. Print Low Level DICOM trace
3. Print 952 trace
4. Turn off DICOM trace
5. Display Ethernet nvram contents
99. Exit Debug Menu
else ’route, ping, netstat, ifconfig, help’
Enter Selection: 1
High level DICOM communications trace enabled, all other disabled
New association starting, NID ‘AnySCU_163.228.142.119’ (client is requesting a session)

Incoming DICOM message from AnySCU_163.228.142.119: (incoming from client AnySCU

163.228.142.119)
****** Begin Command Set ****** (command set is sent to make the request)
(00000002) Affected SOP Class UID
‘1.2.840.10008.5.1.1.1’ Basic Film Session (the request is a Basic Film Session)
(00000100) Command Field
0x0140 320 N–Create RQ (the request is a ”Normalized–Create”)
(00000110) Message ID
0x0001 1
****** End Command Set ******

****** Begin Data Set ****** (no settings data specified in this
transmission)
****** End Data Set ******
Outgoing DICOM message to AnySCU_163.228.142.119: (IMAGER is responding to the request)
****** Begin Command Set ******
(00000002) Affected SOP Class UID
‘1.2.840.10008.5.1.1.1’ Basic Film Session (the response is to the Basic Film Session)
(00000100) Command Field
0x8140 33088 N–Create RSP
(00000120) Message ID Being Responded To
0x0001 1
(00000900) Status
0x0000 0 (this is a key response field, 0 = success)
(00001000) Affected SOP Instance UID
‘3.1’
****** End Command Set ******
****** Begin Data Set ****** (IMAGER is providing some default
settings)
(20000010) Number of Copies
‘1 ’
(20000020) Print Priority
‘HIGH’
(20000030) Medium Type
‘CURRENT ’
(20000040) Film Destination ‘PROCESSOR ’ (should be Processor, not Receive
Magazine)
****** End Data Set ******

7-6 1908110 2001 March Rev. M

Section 7 – Troubleshooting

Incoming DICOM message from AnySCU_163.228.142.119: (client is now requesting setup of image)
***** Begin Command Set ******
(00000002) Affected SOP Class UID
‘1.2.840.10008.5.1.1.2’ Basic Film Box (the request is for a Basic Film Box)
(00000100) Command Field
0x0140 320 N–Create RQ (it is called a Normalized–Create Request)
(00000110) Message ID
0x0002 2
****** End Command Set ******
****** Begin Data Set ******
(20100010) Image Display Format (client is defining only the film format)
‘STANDARD\1,1’ (format is defined by columns, rows)
(20100500) Referenced Film Session Sequence
Start of Item
(00081150) Referenced SOP Class UID
‘1.2.840.10008.5.1.1.1’ Basic Film Session
(00081155) Referenced SOP Instance UID
‘3.1’
End of Item
End of Sequence
****** End Data Set ******

Outgoing DICOM message to AnySCU_163.228.142.119: (the IMAGER is responding)

****** Begin Command Set ******
(00000002) Affected SOP Class UID
‘1.2.840.10008.5.1.1.2’ Basic Film Box (the response is for the Basic Film Box)
(00000100) Command Field
0x8140 33088 N–Create RSP (it is called a Normalized–Create
Response)
(00000120) Message ID Being Responded To
0x0002 2
(00000900) Status
0x0000 0 (status is still 0 which = success)
(00001000) Affected SOP Instance UID
‘3.1.1’
****** End Command Set ******
****** Begin Data Set ****** (IMAGER responding with all necessary
(20100010) Image Display Format print parameters in plain language)
‘STANDARD\1,1’ (format = 1 on 1)
(20100040) Film Orientation
‘PORTRAIT’
(20100050) Film Size ID
‘8INX10IN’
(20100060) Magnification Type
‘CUBIC ’
(20100080) Smoothing Type
‘0 ’ (0 = ”Auto” sharp/smooth interpolation)
(20100100) Border Density
‘BLACK ’
(20100110) Empty Image Density
‘BLACK ’
(20100130) Max Density
0x00d2 210 (210 = a density of 2.1)

2001 March Rev. M 1908110 7-7

Service Manual

(20100140) Trim
‘NO’
(20100150) Configuration Information
‘LUT=0,6 ’ (0 = default Modality Group on 8300, 6 =
(20100500) Referenced Film Session Sequence Contrast Table number 6)
Start of Item
(00081150) Referenced SOP Class UID
‘1.2.840.10008.5.1.1.1’ Basic Film Session
(00081155) Referenced SOP Instance UID
‘3.1’
End of Item
End of Sequence
(20100510) Referenced Basic Image Box Sequence
Start of Item
(00081150) Referenced SOP Class UID
‘1.2.840.10008.5.1.1.4’ Basic Greyscale Image Box
(00081155) Referenced SOP Instance UID
‘3.1.1.1’
End of Item
End of Sequence
****** End Data Set ******

Trap: AnySCU_163.228.142.119 (20200010)

image position: 0x0001 1. (summary of image data trapped or
Trap: AnySCU_163.228.142.119 (00280010) intercepted from client shown in the
image rows: 0x0200 512. subsequent incoming data set)
Trap: AnySCU_163.228.142.119 (00280011)
image columns: 0x0200 512.
Trap: AnySCU_163.228.142.119 (00280100) bits allocated: 0x0008 8.

Incoming DICOM message from AnySCU_163.228.142.119: (client is now requesting image transfer)
****** Begin Command Set ******
(00000003) Requested SOP Class UID
‘1.2.840.10008.5.1.1.4’ Basic Greyscale Image Box (request is for Basic Greyscale Image Box)
(00000100) Command Field
0x0120 288 N–Set RQ (request is called a Normalized–Set
Request)
(00000110) Message ID
0x0005 5
(00001001) Requested SOP Instance UID
‘3.1.1.1’
****** End Command Set ******
****** Begin Data Set ****** (client requesting this image data to be
used)
(20200010) Image Position
Value Intercepted by trap or filter mechanism (intercepted data shown in summary
above)
(20200020) Polarity
‘NORMAL’
(20200110) Preformatted Greyscale Image Sequence
Start of Item
(00280002) Samples Per Pixel
0x0001 1

7-8 1908110 2001 March Rev. M

Section 7 – Troubleshooting

(00280004) Photometric Interpretation

‘MONOCHROME2’
(00280010) Rows
Value Intercepted by trap or filter mechanism
(00280011) Columns
Value Intercepted by trap or filter mechanism
(00280034) Pixel Aspect Ratio
‘1’ (identified as 1 over 1, or 1/1 which = 1)
‘1’
(00280100) Bits Allocated
Value Intercepted by trap or filter mechanism
(00280101) Bits Stored
0x0008 8 (8 bit image data, which IMAGER only
supports)
(00280102) High Bit
0x0007 7
(00280103) Pixel Representation
0x0000 0
(7fe00010) Pixel Data
Value Intercepted by trap or filter mechanism
End of Item
End of Sequence
****** End Data Set ******
Outgoing DICOM message to AnySCU_163.228.142.119:
(8300 is responding)
****** Begin Command Set ******
(00000002) Affected SOP Class UID
‘1.2.840.10008.5.1.1.4’ Basic Greyscale Image Box (the response is for the Basic Greyscale
Box)
(00000100) Command Field
0x8120 33056 N–Set RSP (response is the Normalized–Set
Response)
(00000120) Message ID Being Responded To
0x0005 5
(00000900) Status
0x0000 0 (status still 0, if it was C605 it would
mean out of image memory)
(00001000) Affected SOP Instance UID
‘3.1.1.1’
****** End Command Set ******
****** Begin Data Set ****** (IMAGER response with print parameters it
will use)
(20100060) Magnification Type
‘CUBIC ’
(20100080) Smoothing Type
‘0 ’
(20200010) Image Position
0x0001 1
(20200020) Polarity
‘NORMAL’
(20200110) Preformatted Greyscale Image Sequence
Start of Item

2001 March Rev. M 1908110 7-9

Service Manual

(00280002) Samples Per Pixel

0x0001 1
(00280004) Photometric Interpretation
‘MONOCHROME2 ’
(00280010) Rows
0x0200 512
(00280011) Columns
0x0200 512
(00280034) Pixel Aspect Ratio (1/1 =1.0, 4/3 would = 1.33)
‘1\’
‘1 ’
(00280100) Bits Allocated
0x0008 8
(00280101) Bits Stored
0x0008 8
(00280102) High Bit
0x0007 7
’00280103) Pixel Representation
0x0000 0
End of Item
End of Sequence
****** End Data Set ******

Incoming DICOM message from AnySCU_163.228.142.119: (client’s request to print the image)
****** Begin Command Set ******
(00000003) Requested SOP Class UID
‘1.2.840.10008.5.1.1.2’ Basic Film Box (print request is for a Basic Film Box again)
(00000100) Command Field
0x0130 304 N–Action RQ (request is called Normalized–Action
Request)
(00000110) Message ID
0x000a 10
(00001001) Requested SOP Instance UID
‘3.1.1’
(00001008) Action Type ID
0x0001 1
****** End Command Set ******
****** Begin Data Set ****** (it is an action request so no data is
required)
****** End Data Set ******

Outgoing DICOM message to AnySCU_163.228.142.119: (IMAGER is responding to print request)

****** Begin Command Set ******
(00000002) Affected SOP Class UID
‘1.2.840.10008.5.1.1.2’ Basic Film Box
(00000100) Command Field
0x8130 33072 N–Action RSP
(00000120) Message ID Being Responded To
0x000a 10
(00000900) Status
0x0000 0 (status = 0, request accepted successfully)
(00001000) Affected SOP Instance UID
‘3.1.1’

7-10 1908110 2001 March Rev. M

Section 7 – Troubleshooting

(00001008) Action Type ID

0x0001 1
****** End Command Set ******
****** Begin Data Set ******
****** End Data Set ******
Client AnySCU_163.228.142.119:
DIMSE_GetMessage returns 1: DIMSE_INFO (normal shut down without error –
Peer Requested a RELEASE of the association. key area to look for problems)

Association closing, NID ‘AnySCU_163.228.142.119’ (this client association with IMAGER has
ended)

The following is an example of a 952 Trace:

Debug Menu
1. Print High Level DICOM trace
2. Print Low Level DICOM trace
3. Print 952 trace
4. Turn off DICOM trace
5. Display Ethernet nvram contents
99. Exit Debug Menu
else ‘route, ping, netstat, ifconfig, help’

Enter Selection: 3
952 communications trace enabled, all other disabled
SMM(1) <<RQS (<< is sent from Network PWA to CPU PWA)
SMM(1) >>STA 1 RDY (>> is sent from CPU PWA to Network PWA)
SMM(1) <<NID AnySCU_163.228.142.119 (informing CPU which client is
communicating)
SMM(1) >>PAS (the beginning of an association with that
client)
SMM(1) <<RNS
SMM(1) >>NSB 0 (end of initial setup)
SMM(1) <<AIM 3 513 513 (asking CPU to Allocate Image Memory)
SMM(1) >>AMA 751337472 (response with Allocated Memory Address)
SMM(1) <<RQS
SMM(1) >>STA 1 RDY
SMM(1) <<AQU 3 (image transfer to image memory complete)
SMM(1) >>PAS
SMM(1) <<NID AnySCU_163.228.142.119 (beginning of the request to print)
SMM(1) >>PAS
SMM(1) <<ALI
SMM(1) >>PAS
SMM(1) <<ORI P (requesting orientation to be portrait)
SMM(1) >>PAS
SMM(1) <<DZO 0 0 1 4.39 4.39 0 3 6 (standard film layout DZO)
SMM(1) >>PAS
SMM(1) <<STP 1 7
SMM(1) >>STC
SMM(1) <<EXP
SMM(1) >>EOE
SMM(1) >>PTC (print task complete)
SMM(1) <<CLR 3 (request to close the association)

2001 March Rev. M 1908110 7-11

Service Manual

SMM(1) >>PAS
SMM(1) <<RQS
SMM(1) >>STA 1 RDY
4
SMM(1) >>RDT

Table 7-3. LEDs by Module/PWA Name, Signal Name, and Signal Description

Module/PWA Signal Name Signal Description

Power 20V+ Positive 20V
20V– Negative 20V
15V+ Positive 15V
15V– Negative 15V
5V+ Positive 5V
5V– Negative 5V
12V+ Positive 12V
HEAT1 (lights during heating) Primary heater o/ps
HEAT2 (lights during heating) Secondary (outer) heater o/ps
PS1 (normally on) 380V Boost
PS2 (normally on) Full Wave BRIDGE
FAIL Power Monitor Sense
CPU DS2 One Sheet Present at Film Feed
DS1 Two Sheets Present at Film Feed

7-12 1908110 2001 March Rev. M

Section 7 – Troubleshooting

Module/PWA Signal Name Signal Description

Analog RXD232 Serial input “Receive Data “
across serial port
(RS232)–Lights when host
transfers data, etc.
TXD232 Serial output “Transmit Data”
across serial port (RS232)–Blinks
continuously because of
constant updates to host.
RXD422 Serial input “Receive Data”
across serial port
(RS422)–Lights when key
pressed on keypad.
TXD422 Serial output “Transmit Data”
across serial port (RS422)–Blinks
continuously because of
constant updates to keypad.
VIDEO Video signal present. Lights
when recognizing active video.
Digital RXD232 Serial input “Receive Data”
across serial port
(RS232)–Lights when host
transfers data,etc.
TXD232 Serial output “Transmit Data”
across serial port (RS232)–Blinks
continuously because of
constant updates to host.
RXD422 Serial input “Receive Data”
across serial port
(RS422)–Lights when key
pressed on keypad/host.
TXD422 Serial output “Transmit Data”
across serial port (RS422)–Blinks
continuously because of
constant updates to keypad/host.
REQU Data Request: output,
requesting data from source,
STROBE Data Strobe: input, used to latch
incoming data

2001 March Rev. M 1908110 7-13

Service Manual

Module/PWA Signal Name Signal Description

SCSI LSB Data LSB: The LSB of the SCSI
Bus.
Network RECEIVE Data Receive indicates data is
being received on currently
active port. Frequency of
blinking is relative to receive
activity.
TRANSMIT Data Transmit indicates data is
being sent on currently active
port. Frequency of blinking is
relative to transmit activity.
COLLISION Indicates Collisions between
devices on net. Frequency of
blinking is relative to frequency of
Collisions.
LINK INTEGRITY Monitor of Twisted Pair (TPE)
Link to indicate an active and
valid connection.
POLARITY Indicates a miswired TPE Link.
Card will automatically
compensate if the auto polarity
correction is enabled in S/W.
COAX/~TPE On indicates the 10Base2 coax
line is selected for use. Off
indicates the 10BaseT twisted
Pair port is selected.

7-14 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-1-5. Test Point Locations

Table 7-4. Modules and PWAs

Module/PWA Test Points

Network Input Module TP1 – +5 VDD
TP2 – GND
Digital Input Module TP1 – GND
TP2 – +5VDD
TP3 – +12V
TP4 – (–)12V
SCSI Input Module TP1 – +5 VDD
TP2 – GND
Analog Input Module TP1 – Video
TP2 – AGND
TP3 – AGND
TP4 – GND

CPU PWA TP2 on P8–4 – +15V

TP3 on P8–3 – AGND
TP4 on P8–8 – +5 VDD
TP5 on P8–3 – (–)15V
TP6 on P8–2 – +24V
TP7 on P8–6 – GND
Motor Control PWA TP1 on P5–1 – +24V
TP2 on P5–2 – GND
TP3 on P5–1 – +12V
TP4 on P5–1 – +5 VCC

2001 March Rev. M 1908110 7-15

Service Manual

7-2. Local Panel Error Messages

7-2-1. EC11: Film Tray Unlocked

Local Panel Message Host Alarm Service Log

FILM TRAY UNLOCKED Yes No
INSERT FILM TRAY FULLY TO CLEAR ERROR

SUMMARY
Film tray is not fully seated into Imager.

SEQUENCE OF EVENTS
• As the film tray is pushed in, the film tray in place switch will deactuate.
• The film tray is pushed in further until the tab lock springs into the supply tray.
• When the tab moves into the supply tray, the tray lock release switch actuates and the user is prevented
from pulling the tray out.

PHONE FIX – OPERATOR CORRECTABLE

Remove and reinsert the film tray, using the film saver. Check for an obstruction in the film tray cavity. Reinsert
the tray. Cycle power if necessary.

ON SITE –TECHNICIAN CORRECTABLE

Problem – Tray lock release switch is not actuated.
Solution – Check that the switch is working properly and that the locking tab is still present.

TECH TIPS
Check the cover release button to make sure that it doesn’t bind on the right side panel. If it does, reposition
the panel toward the front of the machine until the button moves freely.

THEORY

7-16 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-2. EC12: Insert Film Tray

Local Panel Message Host Alarm Service Log
INSERT FILM TRAY Yes No

SUMMARY
Customer has not inserted a film tray or the Film Tray in Place Switch is not deactuating.

SEQUENCE OF EVENTS
As the film tray is pushed in, the Film Tray in Place Switch will deactuate.

PHONE FIX – OPERATOR CORRECTABLE

Insert film tray.

ON SITE –TECHNICIAN CORRECTABLE

Problem – The Film Tray in Place Switch is not deactuating.
Solution – Check for proper functioning of the switch.

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-17

Local Panel Message Host Alarm Service Log

REMOVE MISFEED FROM DEVELOPER AREA. Yes Yes
INSERT FILM SAVER TO REMOVE FILM TRAY

SUMMARY
Film is still being sensed at the Processor Entrance Sensor or has not reached the Exit Sensor in time.

SEQUENCE OF EVENTS
• The Processor Entrance Sensor actuates to start timing in the processor.
• The Capstan motor is de-energized.
• Film is driven around the processor by the drum and the processor rollers.
• Timing is checked to make sure that the film clears the Processor Entrance Sensor.

PHONE FIX – OPERATOR CORRECTABLE

Insert film saver and remove film tray. Raise top cover and open the processor cover. Remove any film that
has jammed in the area and close the processor cover. Close the top cover, replace the film tray and remove
the film saver. Press Enter to continue.

ON SITE –TECHNICIAN CORRECTABLE

Problem – The Processor Entrance Sensor is sensing film.
Solution – Check Processor Entrance Sensor functionality (see Tech Tips below). Also: Clean the processor
and entrance rollers. Check spring tension on the entrance roller and processor drive belt tension.
Problem – Film did not get a positive start into the processor. There are several possible causes of this:
1. Bowed entrance guides caused by overtightening of the mounting hardware during production. The bow
produces a high resistance in the film path. (See Solution 1 below.)
2. Metal entrance roller is slipping on its shaft. (See Solution 2 below.)
3. Rubber entrance pinch roller has become glazed or hardened and is no longer grabbing the leading edge
of the film. (See Solution 3 below.)
Solution
1. Remove the processor assembly and loosen the screws and/or nuts that secure the entrance guides
(located on the under side). Confirm that the guides are no longer bowed. Then tighten the hardware only
enough to keep the guides from bowing.
2. Remove the metal entrance roller and confirm that the drive side shaft is securely attached to the roller. If it
is not, remove the shaft, put a small drop of epoxy in the roller and slowly press the shaft back into the
roller. If you are unsuccessful in securing the shaft, replace the roller (78-8100-0293-7).
3. Clean the rubber roller with alcohol. If the surface does not appear to be soft and supple after cleaning,
replace the roller (78-8113-2104-7).

Note
If the problem/solution information above does not resolve the problem, try replacing the CPU PWA.

7-26 1908110 2001 March Rev. M

Section 7 – Troubleshooting

THEORY

2001 March Rev. M 1908110 7-27

Service Manual

7-2-12. EC28: Remove Film From Exit Area

Local Panel Message Host Alarm Service Log

REMOVE FILM FROM EXIT AREA Yes Yes
INSERT FILM SAVER TO REMOVE FILM TRAY

SUMMARY
Film is still being sensed at the Processor Exit Sensor.

SEQUENCE OF EVENTS
• Film is driven around the processor by the drum and the processor rollers.
• Timing is checked to make sure that the film clears the Processor Entrance Sensor.
• The Processor Exit Sensor verifies that the film has made it out of the processor in the correct time.
• The Processor Exit Sensor is checked to make sure film has cleared the sensor in time.
• Film is placed in the exit tray.

PHONE FIX – OPERATOR CORRECTABLE

PHONE FIX – OPERATOR CORRECTABLE

Press Enter to unlock the film tray. Then remove tray, load new film, and reinsert the tray.

ON SITE –TECHNICIAN CORRECTABLE

TECH TIPS
This message is displayed only with software Version 4.4 and higher.

THEORY

2001 March Rev. M 1908110 7-31

Service Manual

7-2-16. EC31: Remove Film Saver

Local Panel Message Host Alarm Service Log

REMOVE FILM SAVER Yes No

SUMMARY
The film saver is being sensed by the machine.

SEQUENCE OF EVENTS
• The film tray is pushed into the machine.
• After the film tray is locked into place, the self test checks to see if the film saver is in place. If it is, the user
is instructed to remove the saver.

PHONE FIX – OPERATOR CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

Problem – The Film Saver in Place Switch is sensing the presence of the film saver.
Solution – Check the Film Saver in Place Switch for proper operation.

TECH TIPS

THEORY

7-32 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-17. EC33: Unable To Feed Film

Local Panel Message Host Alarm Service Log

UNABLE TO FEED FILM Yes Yes
PRESS ENTER TO TRY AGAIN

SUMMARY
Film did not reach the 1 & 2 Sheet Sensors after three tries.

SEQUENCE OF EVENTS
• The Separation/Processor Stepper (SPS) Motor is constantly energized.
• The SPS motor drive belt also drives the separation rollers.
• When a print is requested, the upper separation clutch is energized causing the upper roller to rotate.
• The film feed dc motor will energize and the film feed clutch will energize for one revolution to feed film out
of the tray.
• Film will feed into the separation rollers.
• As the film feeds through the separation rollers, the lower roller of the idler roller assembly will move down.
This roller is mechanically attached to the vane of the 1 & 2 Sheet Sensors and causes the vane to move
away from the sensors.

PHONE FIX – OPERATOR CORRECTABLE

Using the film saver, remove the film tray and check for film obstruction.

ON SITE –TECHNICIAN CORRECTABLE

Problem – Film did not reach the 1 & 2 Sheet Sensors in time.
Solution – Check the functionality of the film feed motor, film feed clutch, separation/processor stepper motor,
upper separation clutch, and 1 & 2 Sheet Sensors. Also make sure that the film liner is notched, and check the
Film Out Sensor.
Problem – Unable to feed film, but all clutches and motors seem to be operating correctly. It is possible that
one of the Allen head setscrews has loosened from one or more pulleys in the film feed area.
Solution – Check all pulleys and ensure that each setscrew is tightened on the flat of the shaft it secures to.

TECH TIPS
The main cause of this problem is the film detector being unable to sense a film out condition and trying to feed
the film liner.

THEORY

2001 March Rev. M 1908110 7-33

Service Manual

7-2-18. EC34: Unable To Unlock Film Tray

Local Panel Message Host Alarm Service Log

UNABLE TO UNLOCK FILM TRAY Yes Yes
REMOVE FILM TRAY MANUALLY TO CONTINUE

SUMMARY
Film tray will not eject when there is no film in the machine.

SEQUENCE OF EVENTS
• The Film Out switch will actuate when there is no film in the film tray.
• The Tray Release Solenoid will energize, pulling back the locking tab and deactuating the Tray Lock
Release Switch.
• The Film Feed Clutch will energize and the Film Feed Motor will energize in the reverse direction, driving
the tray out of the machine.
• The Film Tray in Place Switch will actuate.

PHONE FIX – OPERATOR CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

Problem – The Tray Release Switch is not deactuating.
Solution – Check the Tray Release Solenoid and Tray Release Switch functionality.

TECH TIPS

THEORY

7-34 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-19. EC35: Input A/B Image Sizes Not Identical

Local Panel Message Host Alarm Service Log

INPUT A/B IMAGE SIZES NOT IDENTICAL Yes No
PRESS ENTER TO CONTINUE

SUMMARY
User is trying to capture an image larger/smaller than previous captured image.
SEQUENCE OF EVENTS
• User selects a format and orientation for printing.
• User acquires an image.
• User attempts to acquire another image that is different in width and/or height from the previous image.
• The error is reported, and the image is not acquired.

PHONE FIX – OPERATOR CORRECTABLE

Print or erase the images already acquired. Then acquire the new size images and print them.

ON SITE –TECHNICIAN CORRECTABLE

Advise the operator that the IMAGER cannot print different size images on the same film.

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-35

Service Manual

7-2-20. EC37: Input A/B Image Too Large To Print

Local Panel Message Host Alarm Service Log

INPUT A/B IMAGE TOO LARGE TO PRINT Yes No
PRESS ENTER TO CONTINUE

SUMMARY
User is trying to capture an image larger than the allowable image size for the selected format and orientation.

SEQUENCE OF EVENTS
• User selects a format and orientation for printing.
• User acquires an image.
• The image is larger than the area available in the selected format and orientation.
• The error is reported, and the image is not acquired.

PHONE FIX – OPERATOR CORRECTABLE

Instruct the user to change the format to one with fewer images.

ON SITE –TECHNICIAN CORRECTABLE

TECH TIPS
The printable area of 8 by 10 inch film printed on the IMAGER is 2376 by 2976 pixels. The size of the images
multiplied by the format will be the printed area needed.

THEORY

7-36 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-21. EC39: Input A/B Sync Failure

Local Panel Message Host Alarm Service Log

INPUT A/B SYNC FAILURE Yes Yes

SUMMARY
The sync pulse is not adequate for acquisition.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

Check the video with a scope. If the sync pulse is not prominent, advise the modality OEM.

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-37

Service Manual

7-2-22. EC40: Remove Film Tray

Local Panel Message Host Alarm Service Log

REMOVE FILM TRAY Yes Yes

SUMMARY
The film tray is unloaded, but still in place.

Answer “Yes” to flush the print queue. Then cycle power on the laser imager.

ON SITE –TECHNICIAN CORRECTABLE

Problem: Solid failure in the imaging hardware.
Solution: If just an EC50 error, replace the CPU PWA. If an EC45 and/or EC46, replace the Optics Module.

TECH TIPS

2001 March Rev. M 1908110 7-43

Service Manual

7-2-28. EC51: Unknown SCSI Disk Format Input A/B

Local Panel Message Host Alarm Service Log

UNKNOWN SCSI FORMAT INPUT A/B No Yes

SUMMARY
The system software does not recognize the disk format.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

• Format the disk via the acquisition unit.
• Try a different disk.
Press Enter and verify that the disk format is DEFF or R-DOS.

ON SITE –TECHNICIAN CORRECTABLE

• Ensure that the software version is 4.05 or higher.
• Check that the disk is in an acceptable format. The only acceptable formats are the following:
Camtronics: RDOS
AEGIS: 1.0, 2.0, or 2.4
ATL, GE, etc.: DEFF formatted disks

TECH TIPS

THEORY

7-44 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-29. EC52: Unable to Read DIR Information A/B

Local Panel Message Host Alarm Service Log

UNABLE TO READ DIR INFORMATION A/B No Yes
PRESS ENTER TO CONTINUE

SUMMARY
The imager is unable to read the disk directory.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Press Enter and try to print images from another disk.

ON SITE –TECHNICIAN CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

• Verify that the software version is correct.
• Replace the Input Module.
• Replace the CPU PWA.

TECH TIPS
Swap Input Module slots to see if the problem follows the Input Module or stays with the slot.

THEORY

Before the self test is initiated, the software checks to see the identity of the Input Modules to determine what
tests need to be run .

2001 March Rev. M 1908110 7-55

Service Manual

7-2-40. EC64: Input A/B Header Failure

Local Panel Message Host Alarm Service Log

INPUT A/B HEADER FAILURE Yes Yes

SUMMARY
When this error occurs at a new installation, the digital data parity may be set wrong.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

Problem – Unable to acquire at a new installation.
Solution – Start the digital data parity at none, and try to acquire. If acquisition is still not possible, try a
different parity setting until acquisition is successful.

TECH TIPS
• Make sure that cable is connected.
• A digital acquisition timeout is reported as a header failure.

THEORY

7-56 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-41. EC65: Input A/B Overflow Failure

Local Panel Message Host Alarm Service Log

INPUT A/B OVERFLOW FAILURE Yes Yes

SUMMARY
If the imager detects too many data bytes during the transmission of a line of data, this error is set.

SEQUENCE OF EVENTS
• A line of data is transmitted.
• The imager retries three times to receive a valid line.

PHONE FIX – OPERATOR CORRECTABLE

Reinitiate an acquire.

ON SITE –TECHNICIAN CORRECTABLE

• Check the digital setup parameters (parity).
• Check cabling.
• Replace the Digital Input Module.

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-57

Service Manual

7-2-42. EC66: Input A/B Acquisition Timeout

Local Panel Message Host Alarm Service Log

INPUT A/B ACQUISITION TIMEOUT Yes Yes

SUMMARY
Problem acquiring the complete image within the predetermined time frame.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Reacquire the image. Check cable connections from the modality to the imager.

ON SITE –TECHNICIAN CORRECTABLE

Problem – The imager timed out.
Solution – Verify the setup for image input data.
• Check cabling.
• Check that the imaging source has an image ready.

TECH TIPS

THEORY

7-58 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-43. EC67: Input A/B FIFO Not Empty Failure

Local Panel Message Host Alarm Service Log

INPUT A/B FIFO NOT EMPTY FAILURE Yes Yes

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Reacquire the image to be printed.

Problem – Densitometer photo sensor detector did not detect expected increase in lamp intensity during its
ramp up.
Solution – Clean densitometer sensor and lamp with alcohol pads.
• Check connections to CPU PWA at P3.
• Watch densitometer lamp during calibration. If lamp gets progressively brighter, but Debug program
does not show progressively higher readings (see TECH TIPS below), change the CPU PWA.
• The lamp may not be bright enough for an aging sensor. If R55 on the CPU PWA is not 7.32 K (7321)
ohms, replace the board.
• Replace the densitometer assembly.

TECH TIPS
Connect a terminal program to the serial service port of the IMAGER, and use CTRL D to monitor a calibration
cycle via the debug program of the IMAGER. As current is increased, the output of the A/D is indicated as
digital values for the lamp intensity. The digital values are displayed at three levels. Typical values for a fully
functional system could be:

DL 2, DL 35 DL 196
DH 44 DH 690 DH 3874
The exact numbers are not critical, but the progression from low-to-high levels within this approximate range of
values is most important.

2001 March Rev. M 1908110 7-63

Service Manual

THEORY

The densitometer assembly consists of an incandescent lamp with a green filter and a photo-detector sensor.
Current is passed through the lamp, causing it to illuminate. As the current is increased, the lamp becomes
brighter. Its output is measured by the photo-detector sensor and sent to a pair of A/D converters on the CPU
PWA, which monitors and records the digital values at three stages. The A/D converter circuits consist of a low
gain amplifier that is used for the higher density measurements and a high gain amplifier that is more accurate
for D-min measurements. The resulting measurements are represented by the DL and DH digital values
available during debug monitoring. If the digital values are within an expected range, then the actual values are
recorded as reference points when no film is present.
As a calibration film is passed through the densitometer, new values are recorded for the 20 bands of gray
levels on the sheet. Each scan line of each band is measured to ensure that the middle of each band is used
for value calibration. The digital value output for each amplifier is displayed for each scan line when monitored
with the debug program. These values are compared to the reference values to determine the density of the
bands.

7-64 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-48. EC72: Dynamic RAM Failure

Local Panel Message Host Alarm Service Log

DYNAMIC RAM FAILURE Yes Yes
CALL SERVICE– PRESS ENTER TO CONTINUE

SUMMARY
A dynamic RAM failure may occur while attempting a first acquisition when the video parameters are unknown.
If the parameter for Vertical Active or Vertical Delay is set too high, the laser imager may try to store more than
one frame in memory, which could cause a RAM overload.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Power imager off. Wait 15 seconds, then power back on.

ON SITE –TECHNICIAN CORRECTABLE

Problem – The parameter for the Vertical Active is set too high.
Solution – Reduce the parameter for Vertical Active and/or Vertical Delay by 20%. Acquire an image. If the
error message is received again, readjust the parameter to frame the image properly.

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-65

Service Manual

7-2-49. EC73: Local Panel RAM Failure

Local Panel Message Host Alarm Service Log

LOCAL PANEL RAM FAILURE Yes Yes
CALL SERVICE - PRESS ENTER TO CONTINUE

SUMMARY
Local panel memory failure during self test.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Press Enter. Power imager off. Wait 10-20 seconds, then power back on.

ON SITE –TECHNICIAN CORRECTABLE

Replace the Local Panel. If problem is not solved, replace the CPU PWA.

TECH TIPS
This error may not display if the Local Panel is defective.

THEORY

The local panel RAM is used to store the message being sent to the local panel.

7-66 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-50. EC74: Input A/B DMA Failure

Local Panel Message Host Alarm Service Log

INPUT A/B DMA FAILURE Yes Yes
CALL SERVICE - PRESS ENTER TO CONTINUE

SUMMARY
The transfer to image memory failed.

SEQUENCE OF EVENTS
• Image acquisition was requested.
• Data is transferred from the input buffer on the Input Module to image memory via DMA.

PHONE FIX – OPERATOR CORRECTABLE

Initiate a new acquisition.

ON SITE –TECHNICIAN CORRECTABLE

• Replace the CPU PWA.
• Replace the Input Module.

TECH TIPS

2001 March Rev. M 1908110 7-67

Service Manual

7-2-51. EC 75: FLASH EPROM FAILURE

Local Panel Message Host Alarm Service Log

FLASH EPROM FAILURE No Yes
CALL SERVICE - PRESS ENTER TO CONTINUE

SUMMARY
Flash memory on the CPU PWA is damaged.

SEQUENCE OF EVENTS
The Flash EPROM is checksummed on power up. The error message is generated if the checksum is
incorrect.

PHONE FIX – OPERATOR CORRECTABLE

Power imager off. Wait 5 seconds, then power back on.

ON SITE –TECHNICIAN CORRECTABLE

Problem – The imager firmware has failed.
Solution – Reload the firmware at 19.2 K BTS. If this does not fix the problem, replace the CPU PWA.

TECH TIPS

THEORY

During self-test and after new firmware has been uploaded, the laser imager does a checksum on the Flash
EPROM. If the checksum is not successful, the laser imager automatically jumps into the S-record download
routine and sets the service port to a baud rate of 19.2 K, with 8 bits, no parity, and one stop bit, so that
uploading of firmware is done at this slower speed.

7-68 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-52. EC78: No Response From Keypad A/B

Local Panel Message Host Alarm Service Log

NO RESPONSE FROM KEYPAD A/B No Yes
PRESS ENTER TO CONTINUE

SUMMARY
Imager unable to verify the keypad is attached.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Check the keypad connection on the back of the imager.

TECH TIPS

THEORY

7-74 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-58. EC88: A To D Converter Failure

Local Panel Message Host Alarm Service Log
A TO D CONVERTER FAILURE Yes Yes
TURN OFF IMAGER– CALL SERVICE

SUMMARY
During normal operation and self test, the temperature conversion algorithm detects an invalid value.

SEQUENCE OF EVENTS
The temperature of the drum is calculated by first recording the analog values from the RTD (Resistive
Thermal Device) and then converting those values to digital temperature values.

PHONE FIX – OPERATOR CORRECTABLE

None

ON SITE –TECHNICIAN CORRECTABLE

Problem – A/D conversion values for the processor are wrong. The CPU PWA has detected a problem in the
temperature measurement circuit for the drum.
Checks – Check connection P2 of the CPU PWA. Disconnect P2 and check each RTD’s resistance for
approximately 200 to 300 ohms while drum is rotating.
Solution – If RTD reading is intermittent, replace drum/slip rings assembly. If each RTD measures about the
same constant value, replace CPU PWA.
Problem – Intermittent EC 88 errors and intermittent heating activity in general. Also, EC88 may appear when
processor assembly is opened.
Solution – Make sure that Version 4.6 system software is installed. If the problem persists in spite of the
software, check for grounding problems as follows:
1. Check that the two clips that ground the processor backup rollers are fastened securely. The clip on the
right side grounds the three roller assembly in the main processor housing. The clip on the left side
grounds the nine roller assembly in the clam shell portion. Loose clips may cause an electrostatic
discharge which can alter temperature reading and produce erratic results.
2. Make sure the grounding wire coming from the drum slip rings is attached securely to the processor frame.

TECH TIPS
The system software should be Version 4.6 or higher. This will protect against false A to D Converter failures.
Effective with Version 4.6 software, you can conveniently monitor drum heating activity. with Debug (Control D)
activated, simply type ATODON, and the temperature will be updated to your PC every second. Any
abnormality will cause the local panel to beep, so you do not have to watch your PC display constantly. When
you hear a beep, you can check your PC display to see what abnormality occurred. To stop temperature
monitoring, type ATODOFF.

2001 March Rev. M 1908110 7-75

Service Manual

7-2-59. EC90: Error Writing to Disk SCSI A/B

Local Panel Message Host Alarm Service Log

ERROR WRITING TO DISK SCSI A/B No No
PRESS ENTER TO CONTINUE

SUMMARY
Defective Bernoulli or M/O disk.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Press Enter. If message reappears, try another disk.

ON SITE –TECHNICIAN CORRECTABLE

TECH TIPS

THEORY

7-76 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-60. EC91: No Images Found SCSI A/B

Local Panel Message Host Alarm Service Log

NO IMAGES FOUND SCSI A/B No No
PRESS ENTER TO CONTINUE

SUMMARY
Defective Bernoulli or M/O disk.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Press Enter. Then try to print images from another disk.

ON SITE –TECHNICIAN CORRECTABLE

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-77

Service Manual

7-2-61. EC92: SCSI Bus Protocol Error Input A/B

Local Panel Message Host Alarm Service Log

SCSI BUS PROTOCOL ERROR INPUT A/B No No
PRESS ENTER TO CONTINUE

SUMMARY
Incorrect status returned by the SCSI control chip.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Check SCSI connections.

ON SITE –TECHNICIAN CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

Replace the CPU PWA.

TECH TIPS

THEORY

7-82 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-66. EC97: Non-Volatile RAM Failure

Local Panel Message Host Alarm Service Log

NON–VOLATILE RAM FAILURE Yes Yes
CALL SERVICE - PRESS ENTER TO CONTINUE

SUMMARY
Component problem on CPU PWA. This error occurs only during self test.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Press Enter. Power imager off. Wait 5 seconds, then power back on.

ON SITE –TECHNICIAN CORRECTABLE

Replace the CPU PWA.

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-83

Service Manual

7-2-67. EC98: No Requested Images SCSI A/B

Local Panel Message Host Alarm Service Log

NO REQUESTED IMAGES SCSI A/B No Yes
PRESS ENTER TO CONTINUE

SUMMARY
Exam and images were not specified before requesting a print.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

PHONE FIX – OPERATOR CORRECTABLE

Press Enter to place the imager in service.

ON SITE –TECHNICIAN CORRECTABLE

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-87

Service Manual

7-2-71. Input A/B Program Memory Full

Local Panel Message Host Alarm Service Log

INPUT A/B PROGRAM MEMORY FULL No Yes

SUMMARY
There is a “heap overflow” (software problem).

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Let the system unload prints. (That is, wait for the IMAGER to print the films sitting in print queue.)

ON SITE –TECHNICIAN CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

Try another acquisition, or try another disk.

TECH TIPS

THEORY

2001 March Rev. M 1908110 7-91

Service Manual

7-2-75. No Response from Input A/B

Local Panel Message Host Alarm Service Log

NO RESPONSE FROM INPUT A/B No Yes

SUMMARY
An acquisition was requested, but no image data was present.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

Ensure that the cable connections to the input module are secure. Ensure that the modality is alive. It may
need to be rebooted.

TECH TIPS

THEORY

7-92 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-76. Regulating Temperature

Local Panel Message Host Alarm Service Log

REGULATING TEMPERATURE. No Yes

SUMMARY
Imager is cooling down the developer drum to the set point.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Advise operator that this is a normal activity.

ON SITE –TECHNICIAN CORRECTABLE

Problem – The imager is stuck “Regulating Temperature” after the system has been powered on for some
time.
Cause – This is a bug in earlier versions of system software.
Solution – Upload Version 4.6 system software.

TECH TIPS

THEORY

During the warmup cycle after initial power up, the heater drum is superheated and then allowed to cool down
to the set point. This is done to facilitate thermal equalization in the processor.
During the cool down cycle, REGULATING TEMPERATURE is displayed, informing the user about a normal
machine process.

2001 March Rev. M 1908110 7-93

Service Manual

7-2-77. Unsassigned Error Condition

Local Panel Message Host Alarm Service Log

UNASSIGNED ERROR CONDITION No Yes

SUMMARY
A software error has occurred.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

Power the imager off. Wait 5 seconds, then power it back on again.

ON SITE –TECHNICIAN CORRECTABLE

Upload the most current software revision. If this does not correct the problem, replace the CPU PWA.

THEORY

7-94 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-78. Verify Image Quality

Local Panel Message Host Alarm Service Log

VERY FEW STEPS STEPS IN TOE OF DLOG E No Yes
CURVE. VERIFY IMAGE QUALITY

SUMMARY
This is film calibration information. The message does not go to the local panel. It goes to the service log only,
and is just for information.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

THEORY

2001 March Rev. M 1908110 7-95

Service Manual

7-2-79. Video A/B Calibration Failure. Default Values Used

Local Panel Message Host Alarm Service Log

VIDEO A/B CALIBRATION FAILURE. DEFAULT No Yes
VALUES USED. PRESS ENTER TO CONTINUE

SUMMARY
(Service advice only.) The image area sampled was out of acceptable calibration range. The video calibration
routine could not acquire an image.

SEQUENCE OF EVENTS
This message is returned only during a video calibration process performed by an FE.

PHONE FIX – OPERATOR CORRECTABLE

None.

ON SITE –TECHNICIAN CORRECTABLE

• Verify the video setup parameters.
• Make sure there is a good strong video signal present.

TECH TIPS

THEORY

7-96 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-2-80. Video A/B Calibration Failure

Local Panel Message Host Alarm Service Log

VIDEO A/B CALIBRATION FAILURE. PRESS No Yes
ENTER TO CONTINUE

SUMMARY
(Service advice only.) The image area sampled was out of acceptable calibration range.

SEQUENCE OF EVENTS

PHONE FIX – OPERATOR CORRECTABLE

ON SITE –TECHNICIAN CORRECTABLE

THEORY

7-100 1908110 2001 March Rev. M

Section 7 – Troubleshooting

7-3. Symptoms

7-3-1. Image Quality

Problem Cause Solution

High D-Min Film aged or not stored properly. Run transport test to process film
without imaging. If film is bad,
advise customer of storage
procedures and/or FIFO usage of
film.
Printing totally black films. Memory SIMM in wrong socket Check CPU PWA. If only one
(U7). SIMM is installed, it must be in
lower socket (U8).
Top 1/2 to 1 inch of the film Stripper felt pad has come loose 1. If felt pad has started to detach,
appears lighter in density. from metal backing plate or metal replace the pad assembly.
backing plate has bowed in the
middle. This allows leading edge
of film to bump into felt pad, 2. If metal backing plate is bowed,
causing film to hop. This condition raising the middle, remove pad
causes leading edge of film to cool assembly and gently re-form the
at a much faster rate than rest of assembly so it lays flat when
film, resulting in light density. attached to the stripper assembly.

Top 4 inches of each film is slightly Film exiting the processor is not Order and install the new style
lighter in density or there is a light uniformly cooled. (Film is not lower felt stripper pad
density band on the top 3/4 inch of staying in contact with lower felt (78-8113-2069-2), if this machine
the film. stripper pad.) does not already have it.
Faint scuff-type scratches on the The weight of the film feed roller Call Service Engineering and ask
lower 3 inches of film. causes the film being fed to scrape to test a new film feed roller on this
on the surface of the film below it. machine.
Long scratches in various Dirt and debris are built up in the Inspect and clean (as necessary)
locations on the film. film path. the following areas, in order:
1. Two part guide assembly that
guides film from film tray into
separator assembly.
2. Stainless steel “scoop” that
guides film from separator
assembly to imaging area.
3. Front edge of film tray that film
rides over as it leaves tray.
4. Guide plates that make up the
densitometer.
5. Plates that guide film into
processor assembly and hold
processor entrance switch.
Artifacts down length of film, A piece of debris is attached to Clean the capstan rollers with
recurring every 2 - 3 inches. one of the capstan pinch rollers, alcohol and a lint-free cloth.
interrupting the laser beam.

2001 March Rev. M 1908110 7-101

Service Manual

Problem Cause Solution

Horizontal line across the film, The operator may have cleared a As a phone fix, ask the operator to
about 5-1/2 inches from the top. It jam and attempted to snap the reseat the upper film guide and
may look like image data is upper film guide back into place, ensure that it is snapped into place
missing in one or two scan lines. but only one side got latched. The on both sides.
The line may be intermittent and line on film is caused by the film
occurs across the entire width of hesitating while being imaged, as
the film, traversing both the image it enters the processor assembly.
and the borders.
Films are discolored on the edges. IMAGER has been installed near a Inform customer that imager
wet processor. cannot be in the same area as a
wet processor.
Image fades out down one side of Laser diode or mirror in Optics Replace Optics Module.
the entire film. Module has become mis-aligned.
Image fades out down both sides Thermofuse has blown in the Replace thermofuse in drum.
of entire film. series-wired end zone circuit.
Double or superimposed images. Defective memory module. Replace SIMMs.
With video acquisitions, the image Problem on Analog PWA. Check the Rev. level of the Analog
is shifted every other line PWA. If it is PH (or PH/PH), check
intermittently. the RAM chips in locations
U10-U13. If the chips are labeled
NEC and resistor R55 is not 100
ohms, replace the board with an
update. (If the chips are labeled
Toshiba, there should not be a
problem, even if R55 is not 100
ohms.)

7-3-2. Miscellaneous

Problem Cause Solution

The IMAGER stops in the middle Network Input Module is in slot B, Install Network Input Module in
of power-on self-test (P.O.S.T.) or or if it is in slot A, the module is slot A. (This module only operates
during warmup, and power to defective and is loading the in slot A.) Or try operating the
developer heaters is removed. system. imager with the module removed.
Blank display on Local Panel after The Rev. E Motorola CPU chip Replace the CPU PWA with a
power up. (MC68340FE16E) on the CPU PWA that has an earlier version of
PWA is susceptible to video clock the CPU chip or one that has the E
noise. version chip but has 1K (1001)
ohm resistors in locations R16 and
R17.
The IMAGER stops printing, but Defective CPU PWA. Replace CPU PWA.
the display says “Printing” with no
error message.

7-102 1908110 2001 March Rev. M

Section 7 – Troubleshooting

Problem Cause Solution

A TO D CONVERTER FAILURE Grounding clip used to ground Check and reseat, if necessary,
error message appears when backup roller assemblies is not both grounding clips (one on each
Processor Assembly is opened. seated firmly against mounting side of the Processor Assembly).
screw.
The images printed for a contrast The IMAGER always uses the Instead of printing a contrast test,
test do not look like images contrast table from Modality Group select the desired modality group.
expected from the selected 0, without regard to what was Then acquire and print 12 images,
modality group. selected in the Installation Menu. changing the contrast setting on
the Local Panel for each image
printed.

The density or contrast of internal The internal SMPTE test pattern Remove the SCSI or Network
SMPTE test pattern images is uses the density and contrast Input Module and insert an Analog
different for Analog Input and selected on the Local Panel for or Digital Module. Select the
Network Input Modules installed. Digital and Analog Input Modules, desired density and contrast. Then
but is fixed for SCSI and Network resinsert the SCSI or Network
Input Modules. Input Module to print the internal
SMPTE test pattern.
Unable to feed film (EC33), but all One of the Allen head setscrews Check all pulleys and ensure that
clutches and motors seem to be has loosened from one or more each setscrew is tightened on the
operating correctly. pulleys in the film feed area. flat of the shaft it secures to.
Film tray is locked in and can’t be The film tray detect pin is caught Push the manual release button
pulled out. on the side of the tray because the really hard and pull the tray out. To
cover release button is binding on prevent the problem from
the right side panel. occurring again, order a new cover
release button.
The film bumps into the processor The upper film guide is out of Order a new upper film guide.
entrance guides and causes an tolerance.
EC22.
Intermittent clicking sound from left The compound pulley which Replace the bad bearing. The
side of IMAGER. transfers power from the main bearings are the same common
drive belt to the separator bearing (78-8113-2008-0) used
assembly is made up of a black throughout the IMAGER, and can
plastic pulley housing and two be replaced individually. If the
bearings. If one of the bearings pulley mounting shaft has been
starts to deteriorate, it causes the damaged by the bearing, it also
pulley to emit an intermittent can be easily replaced.
clicking sound.

2001 March Rev. M 1908110 7-103

Service Manual

Occasional thumping sound from The main drive belt, which Tighten the tension of the main
left side of IMAGER. connects the main stepper motor drive belt, as necessary, by
to the separator assembly and the adjusting the eccentric. Check for
processor assembly, can slip a powder buildup on the compound
tooth from time to time, causing pulley, and clean the pulley, as
the thumping sound. This skipping necessary. (The compound pulley
of teeth, which can be caused by a is black, so the powder buildup is
loose belt, results in belt wear. Belt not easy to see.)
wear is evidenced by a buildup of
black “powder” (belt particles) on
the left side frame and base plate.
If the problem condition has
existed for a long time, the black
powder can build up on the teeth
of the compound (two-part) pulley.
This buildup on the pulley can
cause the belt to continue to skip,
even after its tension has been
adjusted.
Missing “Configure Client Defaults” Client IDs are listed in the Establish an association with a
menu item. configure Client Defaults menu client before attempting to
only after a successful association configure client parameter
has been made between the client defaults.
and the IMAGER.
“Processing Failure” DICOM error Too many Client IDs are being To remove a client, use the
message at the modality. stored in the IMAGER. (Client IDs Installation Menu and display the
are a combination of the modality’s Client ID with the Configure Client
AE Title and IP Address.) Excess Defaults Menu. Then press the
Client IDs may be the result of Clear button on the Local Panel of
experimentation by the OEM with the IMAGER. (You will have to
variations in the modality AE Title press Clear a second time to
or IP Address at the customer site. verify your intention.) That client
will be removed from the list. If you
accidentally remove a valid client,
its ID will reappear the next time a
successful association
(communication) is established.

7-104 1908110 2001 March Rev. M

Section 8 – Illustrated Parts Breakdown

8-1. Illustrated Parts Breakdown (IPB)

This Illustrated Parts Breakdown (IPB) section contains the information necessary to locate and identify
assemblies, sub-assemblies, and specific parts of the Kodak DryView 8300 LASER IMAGER.

Part Numbers
All components available on a replacement basis are listed with their Imation identification number. The
parts identification list opposite each illustration provides the description adequate to identify components.
If the component is available only as part of the next higher assembly, the description column provides
the next higher assembly description or identification number.

Locating and Identifying a Part

If physical appearance and general location of an item are known, refer to the view for the assembly or
sub-assembly and locate the item on the exploded view. If machine serial numbers determine a
component, the part ID numbers in this manual are from the most current data available. Make sure part
ID numbers for your component have not been amended by changes and updates made to your machine.
Verify the serial number of your laser imager on the serial plate.

2001 September Rev. N 1908110 8-1

Service Manual

Figure 8-1. Cabinet Assembly

See Figure 8-2

3
12
4

8
10

7 6 5

8-2 1908110 2001 September Rev. N

Section 8 – Illustrated Parts Breakdown

Figure 8-1. Cabinet Assembly

Item No. Part Number Description Qty
1 ...... 78-8098-9202-5 .... LEFT SIDE PANEL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 ...... 78-8100-0495-8 .... SHOCK, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3 ...... 78-8098-9203-3 .... RIGHT SIDE PANEL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4A . . . . . 78-8100-0267-1 .... POWER CORD, 120 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4B . . . . . 78-8100-0268-9 .... POWER CORD, 240 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 ...... 78-8113-2013-0 .... BUTTON, Cover Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6 ...... 78-8100-0005-5 .... COVER LATCH ACTUATOR ASSEMBLY
(Includes Wedge, Shaft, Spring, Button) (See Note 1) . . . . . . . . . . . . 1
7 ...... 78-8100-0004-8 .... COVER LATCH ASSEMBLY (Right, Left and Shaft) . . . . . . . . . . . . . . . . . . 2
8 ...... 78-8113-2003-1 .... SPRING, Cover Latch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
9 ...... 78-8098-9289-2 .... FILM SAVER (See Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10 . . . . . 78-8096-3201-7 .... FILM TRAY ASSEMBLY (See Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
11A . . . . 78-8100-0451-1 .... PANEL, Front, Plain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
11B . . . . 78-8100-0457-8 .... PANEL, Front, Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
12 . . . . . 78-8100-0525-2 . . . . BUTTON, Tray Release (With Foam Spring) (See Note 1) . . . . . . . . . . . . 1

Note 1. Not currently stocked in SPC.

Note 2. Items 9 and 10 are available under a single part number, as follows: 78-8094-9158-8, FILM TRAY
WITH FILM SAVER.

2001 September Rev. N 1908110 8-3

Service Manual

Figure 8-2. Hood Assembly

8-4 1908110 2001 September Rev. N

Section 8 – Illustrated Parts Breakdown

Figure 8-2 Hood Assembly

Item No. Part Number Description Qty
1A . . . . . 78-8100-0090-7 .... STRIKER, Left, Top Cover (See Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1B . . . . . 78-8096-3212-4 .... STRIKER, Right, Top Cover (See Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 ...... 78-8100-0452-9 .... TOP COVER ASSEMBLY (Includes Items 1A, 1B and 6) . . . . . . . . . . . . . 1
3 ...... 78-8096-3204-1 .... FILTER, Charcoal Odor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 ...... 78-8096-3216-5 .... GASKET, Hinge, Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 ...... 78-8100-0502-1 .... GASKET, Filter Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6 ...... 78-8100-0530-2 .... FOAM PAD, Top Cover/Local Panel (See Note 1) . . . . . . . . . . . . . . . . . . . . 2

Note 1. Not currently stocked in Service Parts .

2001 September Rev. N 1908110 8-5

Service Manual

Figure 8-3. Left Side View

1
4
7 8
3

5
9 10

33 12

32 13

30
37 14
29 25
26
28 27 24 34 12 23 22
35, 20
38a 36 21 17
or 19 18
38b 16 8

8-6 1908110 2001 September Rev. N

Section 8 – Illustrated Parts Breakdown

Figure 8-3. Left Side View

Item No. Part Number Description Qty
1 ...... 78-8100-0256-4 . . . . SWITCH, Cover Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 ...... 8E2016 . . . . . . . . . . . CAPSTAN/PINCH ROLL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 ...... 78-8100-0175-6 . . . . MOTOR, Capstan Stepper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 ...... 78-8100-0117-8 . . . . PULLEY, Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 ...... 78-8100-0606-0 . . . . UPPER FILM GUIDE RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6 ...... 78-8100-0177-2 . . . . MOTOR, Film Feed, DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
7 ...... 78-8100-0250-7 . . . . FILMFEED BELT, Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
8 ...... 6E8549 . . . . . . . . . . . ROLLER, Film Feed with Spacers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
9 ...... 78-8100-0179-8 . . . . MOTOR, Stepper, Separator/Processor (With Nylon Hardware) . . . . . . . 1
10 . . . . . 78-8100-0607-8 . . . . GASKET, Motor Dampening (See Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
11 . . . . . 78-8100-0253-1 . . . . BELT, Developer/Separator, Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
12 . . . . . 78-8100-0254-9 . . . . BELT, Film Feed or Developer Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
13 . . . . . 78-8100-0240-8 . . . . LOCAL PANEL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
14 . . . . . 78-8100-0137-6 . . . . ROLLER, Light Dam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 . . . . . Not Used
16 . . . . . 78-8113-2157-5 . . . . FILM FEED ROLLER ASSEMBLY (See Note 1) . . . . . . . . . . . . . . . . . . . . . 1
17 . . . . . 78-8100-0259-8 . . . . SWITCH, Film Carrier Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
18 . . . . . 78-8100-0565-8 . . . . FAN, Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
19 . . . . . 78-8100-0011-3 . . . . TRAY LATCH ACTUATOR ASSEMBLY [Includes Solenoid (#22),
Switch (#17), Latch and Bracket] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
20 . . . . . 78-8100-0260-6 . . . . SWITCH, AC Breaker, On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
21 . . . . . 78-8100-0015-4 . . . . DEVELOPER DRIVE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
22 . . . . . 78-8100-0178-0 . . . . SOLENOID, Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
23 . . . . . 78-8100-0413-1 . . . . CLUTCH, Film Feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
24 . . . . . 78-8100-0111-1 . . . . PULLEY, Film Feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
25 . . . . . 78-8100-0252-3 . . . . SEPARATOR BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
26 . . . . . 78-8100-0041-0 . . . . SEPARATOR ROLLER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
27 . . . . . 78-8113-2002-3 . . . . SPRING, Processor Drive Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
28 . . . . . 78-8100-0203-6 . . . . PULLEY, Capstan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
29 . . . . . 78-8100-0210-1 . . . . BELT, Capstan Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
30 . . . . . 78-8100-0195-4 . . . . CIRCULATION FAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
31 . . . . . 78-8113-2004-9 . . . . RECEPTACLE, AC, Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
32 . . . . . 78-8100-0191-3 . . . . FAN, Processor Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
33 . . . . . 78-8096-3217-3 . . . . GASKET, Plenum, Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
34 . . . . . 78-8113-2008-0 . . . . BEARING, Common . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
35 . . . . . 78-8100-0410-7 . . . . PULLEY, Compound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
36 . . . . . 78-8100-0614-4 . . . . SHAFT, Compound Pulley Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
37 . . . . . 6E8528 . . . . . . . . . . . TENSIONER, Main Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
38a . . . . 8E2045 . . . . . . . . . . . TENSIONER, Separator Belt, Old Style (with Slotted Screw Adjustment) 1
38b . . . . 6E8538 . . . . . . . . . . . TENSIONER, Separator Belt, New Style (with Pivot Arm Adjustment) . . 1
Note 1. Not currently stocked in SPC.

2001 September Rev. N 1908110 8-7

Service Manual

Figure 8-4. Right Side View

18
2 4

4 14 4
19
13
12

10
15
11

16
17 9
8 7

8-8 1908110 2001 September Rev. N

Section 8 – Illustrated Parts Breakdown

Figure 8-4. Right Side View

Item No. Part Number Description Qty
1 ...... 78-8100-0041-0 .... SEPARATOR ROLLER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 ...... 78-8100-0576-5 .... FILM GUIDE RACK (See Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 ...... 78-8113-2007-2 .... SPRING, Media Sense Actuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 ...... 78-8100-0258-0 .... SWITCH, Film Out/Saver/Sense/Carrier in . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5 ...... 78-8100-0024-6 .... LABEL, Warning (See Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6 ...... 78-8113-2005-6 .... FILTER/COVER, Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
7 ...... 78-8100-0602-9 .... OPTICS MODULE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
8 ...... 78-8100-0181-4 .... CABLE, Optics Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
9 ...... 78-8100-0180-6 .... CABLE, Optics Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10 . . . . . 78-8113-2006-4 .... SCREW, Allen Head, 3/16” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
11 . . . . . 78-8100-0328-1 .... BLANK PANEL, Interface (See Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
12 . . . . . 78-8100-0496-6 .... SWITCH, 1-2 Sheet Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
13 . . . . . 78-8113-2000-7 .... SPRING, 1-2 Sheet Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
14 . . . . . 78-8113-2001-5 .... SPRING, Carrier Present Actuator Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 . . . . . 78-8100-0407-3 .... CABLE, MO Drive, Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
16 . . . . . 78-8100-0406-5 .... CABLE, MO Drive, Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
17A . . . 78-8100-0196-2 .... DRIVE, MO, Internal (Olympus) (Includes Bracket and Bezel
for replacement of older Panasonic drives) . . . . . . . . . . . . . . . . . . . . . . . 1
17B . . . 78-8079-0789-0 . . . . DRIVE, MO, Internal (Olympus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
17C . . . 78-8100-0556-7 . . . . DRIVE, MO, 540 MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
18 . . . . . 6E8510 . . . . . . . . . . . SEPARATOR ENTRANCE GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
19 . . . . . 78-8100-0057-6 . . . . PIVOT ARM, Film Tray Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Note 1. Not currently stocked in SPC.

2001 September Rev. N 1908110 8-9

Service Manual

Figure 8-5. Printed Wiring Assemblies and Cables

Right Side
View

2 4 5
3
1

12 10 9
13 11 8 7

Left Side View

19
3 16 18
15 17

8-10 1908110 2001 September Rev. N

Section 8 – Illustrated Parts Breakdown

Figure 8-5. Printed Wiring Assemblies and Cables

Item No. Part Number Description Qty
1 ...... 78-8100-0499-0 .... MICROFUSE, 4A, (Power Supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2A . . . . . 78-8100-0101-2 .... POWER SUPPLY With Fan (For all 8300 locations except Europe) . . . . 1
2B . . . . . 96-0000-2326-5 .... POWER SUPPLY, With Fan (8300/8600 for all locations) . . . . . . . . . . . . . 1
3 ...... 78-8100-0188-9 .... CABLE, CPU to Motor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 ...... 78-8098-9222-3 .... MOTHERBOARD (CPU), PWA (8300 only) . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 ...... 78-8100-0186-3 .... CABLE, CPU to Microswitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6 ...... 78-8100-0187-1 .... CABLE, CPU to Service Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
7A1 . . . 78-8098-9256-1 .... DIGITAL INPUT MODULE, PWA (8300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
7A2 . . . 96-0000-2291-1 .... DIGITAL INPUT MODULE, PWA (8600 or 8300) . . . . . . . . . . . . . . . . . . . . 1
7B . . . . . 78-8098-9259-5 .... SCSI INPUT MODULE, PWA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
7C . . . . 78-8100-0603-7 .... ANALOG INPUT MODULE, PWA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
7D . . . . 78-8100-0209-3 .... NETWORK INPUT MODULE, PWA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
8A . . . . . 78-8079-0732-0 .... SIMM, 4 MB (Maximum of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
8B . . . . . 78-8079-0733-8 .... SIMM, 8 MB (Maximum of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
8C . . . . 78-8079-0734-6 .... SIMM, 16 MB (Maximum of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
9 ...... 78-8100-0185-5 .... CABLE, CPU to Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10 . . . . . 78-8100-0181-4 .... CABLE, Optics Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
11 . . . . . 78-8100-0228-3 .... CABLE, Local Panel to CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
12 . . . . . 78-8100-0407-3 .... CABLE, MO Drive, Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
13 . . . . . 78-8100-0406-5 .... CABLE, MO Drive, Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
14 . . . . . 78-8098-9226-4 .... MOTOR CONTROL, PWA (8300 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 . . . . . 78-8100-0190-5 .... CABLE, Power Supply to Motor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
16 . . . . . 78-8100-0193-9 .... CABLE, Capstan to Motor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
17 . . . . . 78-8100-0197-0 .... CABLE, Motor Control to Separator Processor Stepper Motor . . . . . . . . . 1
18 . . . . . 78-8100-0182-2 .... CABLE, AC Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
19 . . . . . 78-8100-0565-8 .... FAN, Power Supply (See Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Note 1. Not currently stocked in SPC.

2001 September Rev. N 1908110 8-11

Service Manual

Figure 8-6. Processor Assembly

11 15
1
2

19
1
18

7
6
10

9 5

16
8 13 14

8-12 1908110 2001 September Rev. N

Section 8 – Illustrated Parts Breakdown

Figure 8-6. Processor Assembly

Item No. Part Number Description Qty
0 ...... 78-8100-0610-2 . . . . PROCESSOR ASSEMBLY, w/o Densitometer . . . . . . . . . . . . . . . . . . . . . . 1
1 ...... 78-8100-0475-0 . . . . SWITCH, Optical, Entrance or Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 ...... 78-8113-2144-3 . . . . DENSITOMETER ASSEMBLY (Does Not Include Cover) . . . . . . . . . . . . . 1
3 ...... 78-8100-0025-3 . . . . LABEL, Warning (Not Shown) (See Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 ...... 78-8100-0045-1 . . . . DEVELOPER DRUM ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 ...... 78-8100-0363-8 . . . . FUSE, Thermal, 192_C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6 ...... 78-8113-2069–2 . . . FELT PAD, Stripper (Lower for 1 or 2 Pad Stripper Assembly) . . . . . . . . . 1
7 ...... 78-8096-3219-9 . . . . FELT PAD, Stripper (Upper for 2 Pad Stripper Assembly) . . . . . . . . . . . . . 1
8 ...... 78-8100-0580-7 . . . . STRIPPER ASSEMBLY, 2 Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
9 ...... 78-8100-0497-4 . . . . BELT, Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10 . . . . . 78-8100-0522-9 . . . . FILTER, FAZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
11 . . . . . 78-8096-3222-3 . . . . SPACER, Felt, Exit Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
12 . . . . . 78-8113-2104-7 . . . . ROLLER. Idler, Rubber, Exit or Entrance . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
13 . . . . . 78-8113-2102-1 . . . . PRESSURE (3) ROLLER ASSEMBLY, Base . . . . . . . . . . . . . . . . . . . . . . . . 1
14 . . . . . 78-8113-2103-9 . . . . PRESSURE (9) ROLLER ASSEMBLY, Cover . . . . . . . . . . . . . . . . . . . . . . . 1
15 . . . . . 78-8100-0431-3 . . . . ROLLER, Exit Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
16 . . . . . 78-8100-0293-7 . . . . ROLLER, Entrance Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
17 . . . . . 8E2003 . . . . . . . . . . . GROUNDING WIRE, Stripper (Not shown) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
18 . . . . . 8E2026 . . . . . . . . . . . BEARING KIT, Stripper Bar (Pair) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
19 . . . . . 8E2021 . . . . . . . . . . . BUSHINGS, Rubber Entrance or Exit Roller (Pair) . . . . . . . . . . . . . . . . . . . 1
Note 1. Not currently stocked in SPC.

2001 September Rev. N 1908110 8-13

Service Manual

Figure 8-7. Accessory Parts

8-14 1908110 2001 September Rev. N

Section 8 – Illustrated Parts Breakdown

Figure 8-7 Accessory Parts

Item No. Part Number Description Qty
1A . . . . . 78-8100-0378-6 . . . . CABLE, 3 Meter Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1B . . . . . 78-8100-0379-4 . . . . CABLE, 10 Meter Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1C . . . . 78-8100-0380-2 . . . . CABLE, 30 Meter Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1D . . . . 78-8100-0231-7 . . . . CABLE, 60 Meter Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 . . . . . . 78-8098-9279-3 . . . . FOOTSWITCH/CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 . . . . . . 78-8100-0149-1 . . . . KEYPAD, Remote Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 . . . . . . 78-8113-2090-8 . . . . CABLE, Remote Acquire (Interface for Acuson Ultrasound) (Not Shown) 1
5 . . . . . . 26-1011-5222-6 . . . . CABLE, SCSI 1 – SCSI 2, 1 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . 1
6 . . . . . . 26-1012-1102-2 . . . . CABLE, SCSI 1 – SCSI 2, 2 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . 1
7 . . . . . . 26-1012-1101-4 . . . . CABLE, SCSI 2 – SCSI 2, 1 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . 1
8 . . . . . . 26-1011-8351-0 . . . . CABLE, SCSI 2 – SCSI 2, 2 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . 1
9 . . . . . . 26-1011-8472-4 . . . . CABLE, SCSI 1 – SCSI 1, 1 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . 1
10 . . . . . 78-8079-0379-0 . . . . CABLE, SCSI 1 – SCSI 1, 2 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . 1
11 . . . . . 78-8079-9941-8 . . . . TERMINATOR, SCSI 1 (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
12 . . . . . 26-1012-1430-7 . . . . TERMINATOR, SCSI 2 (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
13 . . . . . 78-8053-4695-0 . . . . CABLE, Analog, 3 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
14 . . . . . 78-8053-4059-9 . . . . CABLE, Analog, 10 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 . . . . . 78-8053-4034-2 . . . . CABLE, Analog, 30 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
16 . . . . . 78-8053-4033-4 . . . . CABLE, Analog, 60 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
17 . . . . . 78-8053-4697-6 . . . . CABLE, Digital, 3 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
18 . . . . . 78-8053-4134-0 . . . . CABLE, Digital, 10 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
19 . . . . . 78-8053-4135-7 . . . . CABLE, Digital, 30 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
20 . . . . . 78-8053-4139-9 . . . . CABLE, Digital, 60 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
21 . . . . . 78-8075-2603-9 . . . . CABLE, Genesis (GE), 10 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . 1
22 . . . . . 78-8075-2542-9 . . . . CABLE, Genesis (GE), 30 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . 1
23 . . . . . 78-8075-2543-7 . . . . CABLE, Genesis (GE), 60 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . 1
24 . . . . . 78-8075-2602-1 . . . . CABLE, MFEIB (KEIB) 3 Meter (9-pin M to 9-pin M) (Not Shown) . . . . . . 1
25 . . . . . 78-8063-3964-0 . . . . CABLE, MFEIB (KEIB) 10 Meter (9-pin M to 9-pin M) (Not Shown) . . . . . 1
26 . . . . . 78-8063-3965-7 . . . . CABLE, MFEIB (KEIB) 30 Meter (9-pin M to 9-pin M) (Not Shown) . . . . . 1
27 . . . . . 78-8063-3966-5 . . . . CABLE, MFEIB (KEIB) 60 Meter (9-pin M to 9-pin M) (Not Shown) . . . . . 1
28 . . . . . 78-8113-2024-7 . . . . CABLE, Modem, 8300, (9-pin F to 25-pin M) (Not Shown) . . . . . . . . . . . . 1
29 . . . . . 78-8071-8331-0 . . . . CABLE, RS232 to Host, 3 Meter (25-pin F to 9-pin M) (Not Shown) . . . . 1
30 . . . . . 78-8079-0686-8 . . . . CABLE, RS232 to Host, 10 Meter (25-pin F to 9-pin M) (Not Shown) . . . 1
31 . . . . . 78-8077-4159-6 . . . . CABLE, RS422 to Host, 3 Meter (37-pin F to 9-pin M) (Not Shown) . . . . 1
32 . . . . . 78-8077-4485-5 . . . . CABLE, RS422 to Host, 10 Meter (37-pin F to 9-pin M) (Not Shown) . . . 1
33 . . . . . 78-8077-4486-3 . . . . CABLE, RS422 to Host, 30 Meter (37-pin F to 9-pin M) (Not Shown) . . . 1
34 . . . . . 96-0000-0895-1 . . . . CABLE, RS422 to Host, 60 Meter (37-pin F to 9-pin M) (Not Shown) . . . 1
35 . . . . . 26-1011-7651-4 . . . . CABLE, 10 Base T, 3 Meter (Straight Ethernet) (Not Shown) . . . . . . . . . . 1
36 . . . . . 96-0000-3918-8 . . . . CABLE, 10 Base T, 7.5 Meter (Crossed Pin PEER to PEER)
............................ (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Note 1. Not currently stocked in SPC.

2001 September Rev. N 1908110 8-15

Service Manual

Figure 8-7 Accessory Parts (Continued)

Item No. Part Number Description Qty
37 ..... 26-1012-1431-5 .... CABLE, 10 Base 2, 3 Meter (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
38 ..... 78-9998-2996-9 .... HUB, 10 Base T with 10 Base 2 Port (Not Shown) . . . . . . . . . . . . . . . . . . . 1
39 ..... 78-8075-6004-6 .... CABLE, PC–8300 (AFHU) (Null Modem) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
40 ..... 78-8079-9807-1 .... POEIB, Interface to 8800 (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
41 ..... 26-1007-4918-8 .... GENDER ADAPTER, RS422 Connector (37-pin M/M) (Not Shown) . . . . 1
42 ..... 26-1007-0924-0 .... GENDER ADAPTER, RS422 Connector (37-pin F/F) (Not Shown) . . . . . 1
43 ..... 78-8079-1056-3 .... CLEANING KIT, Disk, MO (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
44 ..... 78-8113-1729-2 .... CLEANING KIT, Head/Lens, MO
[for Panasonic (Internal) drives only] (Not Shown) . . . . . . . . . . . . . . . 1
45 ..... 78-8079-0527-4 . . . . DISK, Test, MO, 128 MB (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
46 ..... 78-8079-0526-6 . . . . DISK, Blank, MO, 128 MB (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
47 ..... 26-1011-5750-6 . . . . DISK, Blank, MO, 230 MB (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
48 ..... 78-8079-0392-3 . . . . DRIVE, Disk, Bernoulli, External (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . 1
49 ..... 78-8113-1554-4 . . . . DRIVE, Disk, MO, External (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
50 ..... 78-8096-3223-1 . . . . GAUGE, Film, 4-11-7 Mil (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
51 ..... 26-1012-1459-6 . . . . HUM ELIMINATOR, (60HZ), HEC-2000 (Not Shown) . . . . . . . . . . . . . . . . . 1
52 ..... 78-8053-4590-3 . . . . VIDEO FILTER, 12 MHz (For Diasonics Ultrasound) (Not Shown) . . . AR
53 ..... 78-8079-9928-5 . . . . MODEM, External, 28.8 K, Hayes (Not Shown) . . . . . . . . . . . . . . . . . . . . . . 1
54 ..... 78-8079-0390-7 . . . . PRINTER, Sony Color, UP-D7000 (Not Shown) . . . . . . . . . . . . . . . . . . . . 1
55 ..... 74-9999-9081-0 . . . . SERVICE HISTORY LOG (Kodak) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AR
56 ..... 74-9999-9080-2 . . . . CUSTOMER MAINTENANCE REPORT . . . . . . . . . . . . . . . . . . . . . . . . . . AR
57 ..... 6E8502 . . . . . . . . . . . MOUNTING KIT, Mobile Van

8-16 1908110 2001 September Rev. N

Section 9 – Diagrams

Section 9 – Diagrams
9-1. Diagrams
Functional Diagram
Input Module Options
Diagrams are supplied in printed form.

2001 March Rev. M 1908110 9-1

Service Manual

BLANK PAGE

9-2 1908110 2001 March Rev. M

Kodak and DryView are trademarks.

Printed in U.S.A. 1908110_N_sep01

EASTMAN KODAK COMPANY

Rochester, NY 14650 HEALTH IMAGING

Walc 2
92% (26)
Walc 2
301 pages
Wisdom Oracle PDF
79% (57)
Wisdom Oracle PDF
248 pages
WALC 10 Memory
83% (12)
WALC 10 Memory
186 pages
Pachislo Manual PDF
100% (3)
Pachislo Manual PDF
30 pages
Kohler tp6805 14/20RESA/L Service Manual
100% (10)
Kohler tp6805 14/20RESA/L Service Manual
128 pages
Dynomite Owners Manual
No ratings yet
Dynomite Owners Manual
405 pages
Gideon's Guardians - New Meth Recipe - A - K - A Easter Bunny Meth
67% (6)
Gideon's Guardians - New Meth Recipe - A - K - A Easter Bunny Meth
50 pages
EPA07 Maxxforce 11, 13 Engine Service Manual
79% (29)
EPA07 Maxxforce 11, 13 Engine Service Manual
490 pages
Unlock Codes All Cell Phones
100% (26)
Unlock Codes All Cell Phones
15 pages
DIY: Immobilizer Hacking For Lost Keys or Swapped ECU
50% (4)
DIY: Immobilizer Hacking For Lost Keys or Swapped ECU
14 pages
Cell Phone Unlock Code Instructions
63% (8)
Cell Phone Unlock Code Instructions
41 pages
A Computer Motherboard Diagram
100% (2)
A Computer Motherboard Diagram
10 pages
Toyota Camry 2002 2006 Workshop Manual
98% (62)
Toyota Camry 2002 2006 Workshop Manual
20 pages
Lock Picking Hotel Rooms
100% (1)
Lock Picking Hotel Rooms
22 pages
2019 Mac Pro Service Technician Manual
No ratings yet
2019 Mac Pro Service Technician Manual
341 pages
All CDMA Codes
75% (4)
All CDMA Codes
17 pages
Logic Pro X Shortcuts
92% (13)
Logic Pro X Shortcuts
11 pages
Site Planing Somatom Sensation 64
No ratings yet
Site Planing Somatom Sensation 64
6 pages
Manuale r306 3x Total Eng g15
No ratings yet
Manuale r306 3x Total Eng g15
391 pages
Artwork and Signature File For: MAN-00799, "Manual, Selenia AEC Calibration"
No ratings yet
Artwork and Signature File For: MAN-00799, "Manual, Selenia AEC Calibration"
12 pages
GE Advantx, Sentry Collimator - User Manual
No ratings yet
GE Advantx, Sentry Collimator - User Manual
26 pages
Bennett HFQ 100 PDF
No ratings yet
Bennett HFQ 100 PDF
204 pages
Holley Carb Manual PDF
100% (1)
Holley Carb Manual PDF
2 pages
IBM Assembly Language Coding (ALC) Part 1
100% (8)
IBM Assembly Language Coding (ALC) Part 1
68 pages
ServiceManualNamux4English PDF
100% (9)
ServiceManualNamux4English PDF
112 pages
All Mobile Tricks
91% (35)
All Mobile Tricks
19 pages
Philips HTD 5540 Service Manual PDF
100% (1)
Philips HTD 5540 Service Manual PDF
56 pages
Todo en 1 CT1
No ratings yet
Todo en 1 CT1
82 pages
Hybrid Graphic Printer: UP-990AD UP-970AD
No ratings yet
Hybrid Graphic Printer: UP-990AD UP-970AD
43 pages
Manual Arcadis Varic
No ratings yet
Manual Arcadis Varic
36 pages
Logiq S8 Manual
No ratings yet
Logiq S8 Manual
2 pages
Senographe DMR + OM
100% (1)
Senographe DMR + OM
98 pages
NX - X - 8000 - Manual - 2009-03-27 2.0
No ratings yet
NX - X - 8000 - Manual - 2009-03-27 2.0
617 pages
Senographe Essential: Technical Publications
No ratings yet
Senographe Essential: Technical Publications
2,044 pages
IU22 Field Installation Instructions, 2.0.0.320 Software Upgrade
No ratings yet
IU22 Field Installation Instructions, 2.0.0.320 Software Upgrade
17 pages
Technical Publications: Revision 2
No ratings yet
Technical Publications: Revision 2
326 pages
Philips Iu22 System Specifications USA
No ratings yet
Philips Iu22 System Specifications USA
22 pages
Impresora Dry Pix Prima
0% (2)
Impresora Dry Pix Prima
3 pages
Release Bulletin Digitaldiagnost 2.0.2 Sp1: Philips Healthcare
No ratings yet
Release Bulletin Digitaldiagnost 2.0.2 Sp1: Philips Healthcare
19 pages
Innova 2100-IQ, 3100/3100-IQ, 4100/4100-IQ Cardiovascular Imaging System SM DVD
100% (1)
Innova 2100-IQ, 3100/3100-IQ, 4100/4100-IQ Cardiovascular Imaging System SM DVD
1 page
Brochure Arcadis Avantic PDF
100% (1)
Brochure Arcadis Avantic PDF
20 pages
CR 30-Xm (English - Datasheet)
No ratings yet
CR 30-Xm (English - Datasheet)
6 pages
Operators Manual AND Installation and Service Manual: 8000-3488 Universal Uni-Matic 325D Generator MODEL NO. 3488/3550
No ratings yet
Operators Manual AND Installation and Service Manual: 8000-3488 Universal Uni-Matic 325D Generator MODEL NO. 3488/3550
38 pages
Integris 1000
No ratings yet
Integris 1000
304 pages
Practix - Mobile Radiography - Practix Convenio Specifications PDF
No ratings yet
Practix - Mobile Radiography - Practix Convenio Specifications PDF
6 pages
Innova Pressure Control BD Installation
No ratings yet
Innova Pressure Control BD Installation
10 pages
Bucky C-TS PDF
No ratings yet
Bucky C-TS PDF
33 pages
Kodak POC 140140 Servicemanual PDF
No ratings yet
Kodak POC 140140 Servicemanual PDF
154 pages
Product Information: Toshiba X-Ray Tube D-125 / D-125S / D-125SB
No ratings yet
Product Information: Toshiba X-Ray Tube D-125 / D-125S / D-125SB
8 pages
D502805_SCANORA_3D_service
No ratings yet
D502805_SCANORA_3D_service
243 pages
Urgent Field Safety Notice PHILIPS MX 16-Slice Computed Tomography
No ratings yet
Urgent Field Safety Notice PHILIPS MX 16-Slice Computed Tomography
4 pages
Logiq p5 SM
No ratings yet
Logiq p5 SM
520 pages
Agfa Drystar 5300 - Software Paches PDF
No ratings yet
Agfa Drystar 5300 - Software Paches PDF
18 pages
PLX101B High Frequency Mobile X-Ray Camera: User'S Manual
No ratings yet
PLX101B High Frequency Mobile X-Ray Camera: User'S Manual
24 pages
2008K2 Cal Procedures (508137 Rev E)
No ratings yet
2008K2 Cal Procedures (508137 Rev E)
84 pages
HF-110A and HF-110AM: Operator I Installation I Service Manual
No ratings yet
HF-110A and HF-110AM: Operator I Installation I Service Manual
41 pages
Specifications For The CARESTREAM DRX-Evolution/DRX-Evolution Plus
No ratings yet
Specifications For The CARESTREAM DRX-Evolution/DRX-Evolution Plus
56 pages
ZIIEHM Exposcop 7000
No ratings yet
ZIIEHM Exposcop 7000
352 pages
OD Eleva All Digital Disposal
0% (1)
OD Eleva All Digital Disposal
43 pages
Ir368-Usa - Esp Part List
No ratings yet
Ir368-Usa - Esp Part List
80 pages
IU22 XMATRIX Specifications NA
No ratings yet
IU22 XMATRIX Specifications NA
36 pages
Rws Service PDF
No ratings yet
Rws Service PDF
288 pages
Manual Arcadis
No ratings yet
Manual Arcadis
12 pages
Smo F551 SD
No ratings yet
Smo F551 SD
46 pages
Advancing Productivity and Efficiency For Your R&F Needs.: Kalare
No ratings yet
Advancing Productivity and Efficiency For Your R&F Needs.: Kalare
2 pages
Bennett HFQ 300, 450, 600 X-Ray - User Manual PDF
No ratings yet
Bennett HFQ 300, 450, 600 X-Ray - User Manual PDF
49 pages
Brochue Arcadis Varic PDF
No ratings yet
Brochue Arcadis Varic PDF
16 pages
Software Update Kit Iso-C 3D Version P4
100% (2)
Software Update Kit Iso-C 3D Version P4
58 pages
Eaton Evolution Manual
No ratings yet
Eaton Evolution Manual
22 pages
Sias' C-Arm Range
No ratings yet
Sias' C-Arm Range
2 pages
SIREMOBIL Compact L Competition: Michael Bodky, SP CRM M3
No ratings yet
SIREMOBIL Compact L Competition: Michael Bodky, SP CRM M3
21 pages
005 00147 00e Dicombox Operator Manual PDF
No ratings yet
005 00147 00e Dicombox Operator Manual PDF
46 pages
GE MAC 5000 ECG - User Manual
No ratings yet
GE MAC 5000 ECG - User Manual
236 pages
Marquette Cardioserv V4 - Service Manual PDF
No ratings yet
Marquette Cardioserv V4 - Service Manual PDF
113 pages
Test - 04 Failed - GE Healthcare AMX 4 Plus - MedWrench
No ratings yet
Test - 04 Failed - GE Healthcare AMX 4 Plus - MedWrench
7 pages
ImageDiagnost Installation Manual 4.6.0.en
No ratings yet
ImageDiagnost Installation Manual 4.6.0.en
272 pages
Service Manual, Rev. B, Draft: Kodak Dryview 8200 Laser Imager
No ratings yet
Service Manual, Rev. B, Draft: Kodak Dryview 8200 Laser Imager
374 pages
Service Manual, Rev. D: Kodak Dryview 8100 Laser Imager
No ratings yet
Service Manual, Rev. D: Kodak Dryview 8100 Laser Imager
382 pages
Service Manual, Rev. E: Mammography
No ratings yet
Service Manual, Rev. E: Mammography
222 pages
Kodak DryView 8700-8500
No ratings yet
Kodak DryView 8700-8500
423 pages
User Guide, Rev. B: Kodak Dryview 8700/8500 Laser Imager
No ratings yet
User Guide, Rev. B: Kodak Dryview 8700/8500 Laser Imager
133 pages
User Guide, Rev. D: Kodak Dryview 8300 Laser Imager
No ratings yet
User Guide, Rev. D: Kodak Dryview 8300 Laser Imager
85 pages
8100 Service Manual Rev J PDF
No ratings yet
8100 Service Manual Rev J PDF
466 pages
BV PULSERA SERVICE MANUAL ORIG
No ratings yet
BV PULSERA SERVICE MANUAL ORIG
10 pages
Smaub
No ratings yet
Smaub
67 pages
Smaua
No ratings yet
Smaua
51 pages
SM 9415
No ratings yet
SM 9415
136 pages
Service Manual, Rev. B: Kodak Pacs Link 9405 Print Server
No ratings yet
Service Manual, Rev. B: Kodak Pacs Link 9405 Print Server
115 pages
Ug 8800
No ratings yet
Ug 8800
59 pages
SM 9410
No ratings yet
SM 9410
309 pages
Toc 3
No ratings yet
Toc 3
1 page
User Guide, Rev. B: Mammography
No ratings yet
User Guide, Rev. B: Mammography
63 pages
Toc 5
No ratings yet
Toc 5
1 page
Ug 8600
No ratings yet
Ug 8600
69 pages
Diy Inmobilizer Circuits
100% (5)
Diy Inmobilizer Circuits
18 pages
Samsung Full Codes
100% (5)
Samsung Full Codes
7 pages
Direct Key Web
No ratings yet
Direct Key Web
7 pages
Data Link, Fault Tracing V2
100% (1)
Data Link, Fault Tracing V2
22 pages
How Cell Phones Work
No ratings yet
How Cell Phones Work
12 pages
Hints Computer System Design
100% (1)
Hints Computer System Design
27 pages
Manual Ecu D Citit
No ratings yet
Manual Ecu D Citit
145 pages
Charmed RPG Player Handbook
75% (4)
Charmed RPG Player Handbook
18 pages
NE8392C Coaxial Transceiver Interface For Ethernet/Thin Ethernet
No ratings yet
NE8392C Coaxial Transceiver Interface For Ethernet/Thin Ethernet
9 pages
001 Slides - Layer 2 Forwarding
No ratings yet
001 Slides - Layer 2 Forwarding
36 pages
Coaxial
No ratings yet
Coaxial
2 pages
IEEE Standards
No ratings yet
IEEE Standards
3 pages
Computer Network Tutorial by Vipul
100% (1)
Computer Network Tutorial by Vipul
21 pages
Testking Exam Questions & Answers: Br0-002 Comptia Network + Bridge Exam
No ratings yet
Testking Exam Questions & Answers: Br0-002 Comptia Network + Bridge Exam
6 pages
Chapter 2 - Data Communication and Transmission Media
No ratings yet
Chapter 2 - Data Communication and Transmission Media
29 pages
IEEE 802.3 and Ethernet
No ratings yet
IEEE 802.3 and Ethernet
3 pages
Multiple-Choice Questions: Sheet 10 (Chapter 13)
No ratings yet
Multiple-Choice Questions: Sheet 10 (Chapter 13)
3 pages
Mil-10p Micro-Twist Specsheet
No ratings yet
Mil-10p Micro-Twist Specsheet
2 pages
GEH 6371 Unit Controller 2000VME (UC2000V) Operation and Maintenance
No ratings yet
GEH 6371 Unit Controller 2000VME (UC2000V) Operation and Maintenance
68 pages
10 Base 2
No ratings yet
10 Base 2
4 pages
Study The Physical Media of Connectivity: Practical No. 1
No ratings yet
Study The Physical Media of Connectivity: Practical No. 1
40 pages
NetWorth Series 1000 EtherNext MicroHub Lite
No ratings yet
NetWorth Series 1000 EtherNext MicroHub Lite
52 pages
TVL - Computer System Servicing G12: Let Us Discover
No ratings yet
TVL - Computer System Servicing G12: Let Us Discover
7 pages
Chapter 15
No ratings yet
Chapter 15
29 pages
Feleke Network Cables Lecture 3
No ratings yet
Feleke Network Cables Lecture 3
69 pages
Data Communications
No ratings yet
Data Communications
271 pages