Scribd
Upload
103 views2 pages

HHD - S.Technical - Information - ASSET - DOC - 2331274

The HHD-S Cavity anchor is a metal undercut anchor with a metric screw designed for fastening to drywall and other materials. It provides metal-to-metal fastening and reliable performance. Recommended load values are provided for various anchor sizes and materials like hollow brick, gypsum board, and fiber-reinforced gypsum board with thicknesses ranging from 10mm to 30mm. Installation instructions specify using a rotary hammer and expansion tool. Settings details list anchor dimensions, drill bit sizes, and minimum/maximum panel thicknesses for different anchor configurations.

Uploaded by

Hoa Ly Trắng
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
103 views2 pages

HHD - S.Technical - Information - ASSET - DOC - 2331274

The HHD-S Cavity anchor is a metal undercut anchor with a metric screw designed for fastening to drywall and other materials. It provides metal-to-metal fastening and reliable performance. Recommended load values are provided for various anchor sizes and materials like hollow brick, gypsum board, and fiber-reinforced gypsum board with thicknesses ranging from 10mm to 30mm. Installation instructions specify using a rotary hammer and expansion tool. Settings details list anchor dimensions, drill bit sizes, and minimum/maximum panel thicknesses for different anchor configurations.

Uploaded by

Hoa Ly Trắng
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

HHD-S Cavity anchor

HHD-S Cavity anchor


Anchor version Benefits
- metal undercut anchor with
metric screw, esp. for drywall
HHD-S - metal to metal fastening
- reliable undercut

Drywall

Basic loading data (for a single anchor)


All data in this section applies to
- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Base material as specified in the table
- Borehole drilling without hammering

Recommended loads a)
Anchor size M4 M5 M6 M8
Hollow brick Nrec [kN] 0,1 - - -
web thickness 20mm Vrec [kN] 0,3 - - -
Gypsum board Nrec [kN] 0,2 0,2 0,2 0,2
Thickness 10mm Vrec [kN] 0,5 0,5 0,5 0,5
Gypsum board Nrec [kN] 0,2 0,2 0,2 0,2
Thickness 12,5mm Vrec [kN] 0,5 0,5 0,5 0,5
Gypsum board Nrec [kN] - 0,4 0,3 0,4
Thickness 2x12,5mm Vrec [kN] - 1 0,9 1
Fibre reinforced gypsum board Nrec [kN] 0,2 0,3 0,25 0,4
Thickness 10mm Vrec [kN] 0,5 0,6 0,8 0,9
Fibre reinforced gypsum board Nrec [kN] 0,3 0,5 0,3 0,6
Thickness 12,5mm Vrec [kN] 0,6 1 1 1,2
Fibre reinforced gypsum board Nrec [kN] - 0,9 0,8 0,9
Thickness 2x12,5mm Vrec [kN] - 1,1 1,8 1,7
a) With overall global safety factor J = 3 to the characteristic loads and a partial safety factor of J = 1,4 to the
design values.

Materials
Material quality
Part Material
Sleeve Carbon steel, galvanised
Screw Carbon steel, galvanised

404 These pages are part of the Anchor Fastening Technology Manual issue September 2014 09 / 2014
HHD-S Cavity anchor

Setting
Installation equipment
Anchor size
Rotary hammer TE2… TE16
Other tools Screwdriver, HHD-SZ2 expansion tool

Setting instruction

Setting details:

Setting details HHD-S


Anchor version M4/4 M4/6 M4/12 M4/19 M5/8 M5/12 M5/25
Nominal diameter of
do [mm] 8 8 8 8 10 10 10
drill bit
Anchor length l [mm] 20 32 38 45 38 52 65
Anchor neck length h [mm] 4 6 12,5 19 8 12,5 25
Screw length lS ≥ [mm] 25 39 45 52 45 58 71
Screw diameter d M4 M4 M4 M4 M5 M5 M5
Panel thickness hmin,max [mm] 3-4 6-7 10 - 13 18 - 20 6-8 11 - 13 23 - 25
Max. fixable thickness
t f ix [mm] 15 25 25 25 25 30 30
for pre-setting

Anchor version M6/9 M6/12 M6/24 M6/40 M8/12 M8/24 M8/40


Nominal diameter of
do [mm] 12 12 12 12 12 12 12
drill bit
Anchor length l [mm] 38 52 65 80 54 66 83
Anchor neck length h [mm] 9 12,5 25 40 12,5 25 40
Screw length lS ≥ [mm] 45 58 71 88 60 72 90
Screw diameter d M6 M6 M6 M6 M8 M8 M8
Panel thickness hmin,max [mm] 7-9 11 - 13 23 - 25 38 - 40 11 - 13 23 - 25 38 – 40
Max. fixable thickness
t f ix [mm] 20 30 30 30 30 30 35
for pre-setting

09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September 2014 405

You might also like