Flow Switch FF-...

GR
Materials Rg 5 nickelled, 1.4310, CW614N nickelled,
medium-contact NBR, hard ferrite
Non-medium- PA, PVC
contact materials
Weight see table "Dimensions and weights"
Installation Standard: horizontal inwards flow; switching
location head not recommended underneath; other
installation positions are possible; the
installation position affects the switching
point and range.

Ranges
Details in the table correspond to horizontal inwards flow with
decreasing flow rate.

G DN Switchin Types Qmax.

point recommended
l/min H2O
● Adjusted switching value Choose
● Highly reproducible between
● Insensitive to dirt G 1/4 DN 8 0.4 - 9 FF-008GR009 7
G 3/8 DN 10 0.4 - 10 FF-010GR010 10
Characteristics
G 1/2 DN 15 0.4 - 12 FF-015GR012 22
The volume flow raises a piston (fitted with a magnet) out from a G 3/4 DN 20 0.6 - 25 FF-020GR025 38
valve seat against a spring force. The piston actuates a G1 DN 25 1.5 - 40 FF-025GR040 60
hermetically separated reed switch.
G 11/4 DN 32 2.0 - 60 FF-032GR060 100
G 11/2 DN 40 3.0 - 90 FF-040GR090 150
Technical data
G2 DN 50 5.0 -150 FF-050GR150 250
Switch reed switch Special ranges are available
Nominal width DN 8..50 (DN 65..80 available on request)
Process female thread G 1/4 ..G 2 Dimensions and weights
connection
G Types L H SW X Weight
Adjustment range 0.4..150 l/min for details see kg
Qmax. to 250 l/min table "Ranges" G 1/4 FF-008GR... 68 80 29 12 0.6
Tolerance ±3 % of the switching value, G 3/8 FF-010GR...
minimum ±0.3 l/min
G 1/2 FF-015GR... 13
Pressure G 1/4..G 1/2 - PN 200 bar
G 3/4 FF-020GR... 73 90 32 11 0.7
resistance G 3/4..G 1 - PN 25 bar
G1 FF-025GR... 87 41 14 1.0
G 11/4..G 2 - PN 16 bar
G 11/4 FF-032GR... 98 95 52 1.5
Medium DN 8..15 -20..+110 °C
G 11/2 FF-040GR... 113 95 59 2.0
temperature ≥DN 20 -20..+ 90 °C
G2 FF-050GR... 137 103 72 17,5 3,1
Ambient -20..+70 °C
temperature
Media water (oils available on request)
Wiring normally open (n.o.)
no. 0.212

brown blue
optionally, normally closed
no. 0.214
(not all adjustment
ranges are
possible, brown blue
please enquire)
Switching voltage max. 230 V AC
Switching current max. 1 A
Switching max. 50 VA
capacity
Protection class 1 - PE connection
Ingress protection IP 65
Electrical cable 1.8 m
connection

pi-ho_fkv-ff-gr_e V1.02-04 1
Handling and operation Ordering code
● Include straight calming section of 5 x DN in inlet and outlet 1. 2. 3. 4. 5.
● If the media are dirty, install a filter FF - G R
(use magnetic filter for ferritic components).
● It must be ensured that the values given for voltage, current, =Option
and power are not exceeded.
● When switched on, a load must be connected in series. 1. Nominal width
The electrical details apply to ohmic loads. 008 DN 8 - G 1/4
Capacitive, inductive and lamp loads must be operated using a 010 DN 10 - G 3/8
protective circuit. 015 DN 15 - G 1/2
020 DN 20 - G 3/4
025 DN 25 - G 1
032 DN 32 - G 11/4
040 DN 40 - G 11/2
050 DN 50 - G 2
2. Process connection
G female thread
3. Connection material
R red bronze
4. Switching point H2O can be set as
desired between
009 0.4 - 9 l/min 
010 0.4 - 10 l/min 
012 0.4 - 12 l/min 
025 0.6 - 25 l/min 
040 1.5 - 40 l/min 
060 2.0 - 60 l/min 
090 3.0 - 90 l/min 
150 5.0 - 150 l/min 
5. Wiring
S 'normally open', no. 0.212
 'normally closed', no. 0.214
O
(please enquire about range)

Options
● Adjustment for oil or gas
● Special values

Ordering information
● Specify direction of flow, medium, and switching point.
● For oils, state viscosity, temperature and designation
(e.g. ISO VG 68) (enquire about range).
● For gases, state pressure (relative or absolute), temperature
and medium (e.g. air) (enquire about range).

2 pi-ho_fkv-ff-gr_e V1.02-04