SOLENOID VALVES NC

2
2/2
direct operated Series
for high pressure fluids
1

2
262
1/8 - 1/4 NO
15 mm compression fittings 1

FEATURES
• High operating pressure
• RoHS compliance
• AC/DC interchangeability of the coil possible only for NC (10,1 W/11,6 W and
17,1 W/22,6 W)
• Valves do not require a minimum operating pressure
• Large selection of seal materials providing wide chemical compatibility
• Compliance with UL and CSA standards
• The solenoid valves satisfy all relevant EU directives
GENERAL
Differential pressure See «SPECIFICATIONS» [1 bar =100 kPa]
Maximum viscosity 65 cSt (mm2/s)
Response time 5 - 25 ms
fluids () temperature range (TS) seal materials ()
air, inert gas, water, oil -25°C to +80°C NBR (nitrile)
0°C to +60°C UR (cast urethane)
GENERAL
MATERIALS IN CONTACT WITH FLUID
() Ensure that the compatibility of the fluids in contact with the materials is verified
Body Brass Stainless steel, AISI 304
Shading coil Copper Silver
Core tube Stainless steel, AISI 305
Core and plugnut Stainless steel, AISI 430F
Springs Stainless steel, AISI 302
Seal NBR
Disc NBR or UR
Disc holder (NO function) PA
ELECTRICAL CHARACTERISTICS
Coil insulation class F (AC) or H (DC)
Connector Spade plug (cable Ø 6-10 mm)
Connector specification ISO 4400 / EN 175301-803, form A
Electrical safety IEC 335
Electrical enclosure protection Moulded IP65 (EN 60529)
Standard voltages DC (=) : 24V - 48V
(Other voltages and 60 Hz on request) AC (~) : 24V - 48V - 115V - 230V/50 Hz
1 2
operator power ratings
ambient replacement coil (1)

temperature inrush holding hot/cold

range (TS) ~ ~ = ~ =
(°C) (VA) (VA) (W) (W) 230 V/50 Hz 24 V DC NC function
30 16 8,1 7,7/ 10,6 238213-059 238513-006
45 20 11,1 12,5/18,6 238213-157 238513-106
-25 to +55
50 25 10,1 8,5/11,6 238613-059 238913-006
70 40 17,1 15,1/22,6 238613-159 238913-106
All 238 basic numbers are UL & CSA approved and marked with the UR (recognised component) &
(1) 

CSA logos.
Availability, design and specifications are subject to change without notice. All rights reserved.

OPTIONS
FPM (fluoroelastomer):
-15°C to +100°C (coil class F)
-15°C to +120°C (coil class H)
Seals and disc () (2)
EPDM (ethylene-propylene), 0°C to +100°C
(fluid temperature range)
CR (chloroprene), 0°C to +80°C
PTFE: -15°C to +100°C (coil class F)
-15°C to +120°C (coil class H)
Oxygen service, FPM disc and seals, see “15-DIGIT PRODUCT CODE”

WRAS approval, EPDM disc and seals, see “15-DIGIT PRODUCT CODE” 1 2
Magnetic latching versions, reverse polarity DC voltages,
see “15-DIGIT PRODUCT CODE FOR MAGNETIC LATCHING VERSION ONLY”
15 mm compression-fitting body, supplied with nut and olive, NO function
see “15-DIGIT PRODUCT CODE”
Plug with visual indication and peak voltage suppression or
with cable length of 2 m (see Solenoids, Coils & Accessories section)
00167GB-2017/R01

Explosionproof enclosures for use in zones 1/21-2/22, categories 2-3 to

ATEX Directive 2014/34/EU (See page 4)
() Ensure that the compatibility of the fluids in contact with the materials is verified.
(2) 
The minimum ambient temperature of the solenoid valve is determined by the limitations of minimum
temperature indicated.

All leaflets are available on: www.asco.com

Solenoid Valves (2/2) - 5
 SOLENOID VALVES SERIES 262

SPECIFICATIONS 15-DIGIT PRODUCT CODE

operating pressure voltage code
flow differential (bar)

dimensions /
orifice power coil

115 V/50 Hz
230 V/50 Hz
pipe coefficient

24 V/50 Hz
48 V/50 Hz
size max. (PS) (W) brass stainless steel

24 V/DC
48 V/DC
size Kv air () water () oil ()

type (1)
thread
min.

type
(mm) (m3/h) (l/min) ~ = ~ = ~ = ~ =
WITHOUT MANUAL OPERATOR
NC - Normally closed, NBR seal and disc
G 01 G262K001S1N00 -
1,2 0,05 0,8 0 51 51 51 41 50 34 8,1 10,6
NPT 01 - 8262K012S1N00
G 01 G262K014S1N00 -
2,4 0,18 3 0 25 14 22 10 13 10 8,1 10,6
1/8 NPT 01 - 8262K015S1N00
G 01 G262K002S1N00 -
12 8 12 6,5 8 6 8,1 10,6
3,2 0,3 5 0 NPT 01 - 8262K006S1N00
18 10 17 8 13 8 11,1 18,6 G 01 G262K016S1N00 -
103 68 103 66 103 58 10,1 11,6 G* 02 E262K200S1W00 (2) -
G* 02 - E262K214S1W00 (2)
151 68 151 66 117 58 10,1 11,6
1,2 0,05 0,8 0 NPT 02 - 8262K214S1W00 (2)
G* 01 E262K019S1N00 -
51 51 51 41 50 34 8,1 10,6
NPT 01 - 8262K080S1N00
G* 01 E262K020S1N00 -
25 14 22 10 11 10 8,1 10,6
NPT 01 - 8262K086S1N00
34 19 24 13 18 13 11,1 18,6 G* 01 E262K021S1N00 -
2,4 0,18 3 0 G* 02 E262K108S1N00 E262K182S1N00
40 16 28 16 28 15 10,1 11,6
NPT 02 - 8262K182S1N00
G* 02 E262K109S1N00 E262K183S1N00
49 41 28 28 28 27 17,1 22,6
NPT 02 - 8262K183S1N00
G* 01 E262K022S1N00 -
12 8 12 6,5 6 5,5 8,1 10,6
NPT 01 - 8262K007S1N00
FL FR FT F8 H1 H9
18 10 17 8 10 7,5 11,1 18,6 G* 01 E262K023S1N00 -
3,2 0,3 5 0 G* 02 E262K232S1N00 E262K184S1N00
23 7,5 20 7 14 6,5 10,1 11,6
NPT 02 - 8262K184S1N00
1/4 G* 02 E262K110S1N00 E262K185S1N00
34 17 26 17 24 15 17,1 22,6
NPT 02 - 8262K185S1N00
G* 02 E262K202S1N00 E262K220S1N00
14 3,5 13 3,5 10 3,5 10,1 11,6
NPT 02 - 8262K220S1N00
4 0,45 7,5 0
G* 02 E262K112S1N00 E262K187S1N00
20 7,5 14 7,5 14 7,5 17,1 22,6
NPT 02 - 8262K187S1N00
G* 02 E262K208S1N00 E262K226S1N00
6,5 2 6,5 2 6,5 2 10,1 11,6
NPT 02 - 8262K226S1N00
G* 02 E262K114S1N00 E262K188S1N00
5,6 0,63 10,5 0 8,5 4 8,5 4 8,5 4 17,1 22,6
NPT 02 - 8262K188S1N00
G* 01 E262K013S1N00 -
3,5 2 3,5 2 2,5 1,9 8,1 10,6
NPT 01 - 8262K036S1N00
G* 01 E262K090S1N00 -
2 1,6 2 1,5 2 1,3 8,1 10,6
NPT 01 - 8262K038S1N00
G* 02 E262K210S1N00 E262K189S1N00
7,1 0,76 12,7 0 4 1,5 5 1,5 4 1,3 10,1 11,6
NPT 02 - 8262K189S1N00
G* 02 E262K212S1N00 E262K230S1N00
6 3 6 3 6 3 17,1 22,6
NPT 02 - 8262K230S1N00
NO - Normally open, NBR seal and disc

Availability, design and specifications are subject to change without notice. All rights reserved.
G 02 G262K155S1W00 (2) G262K168S1W00 (2)
79 44 62 33 55 22 10,1 11,6
NPT 02 - 8262K168S1W00 (2)
1,2 0,05 0,8 0
G 02 G262K156S1N00 G262K169S1N00
51 44 51 38 51 27 10,1 11,6
NPT 02 - 8262K169S1N00
1/8
G 02 G262K128S1N00 G262K236S1N00
2,4 0,18 3 0 18 11 15 9 12 6,5 10,1 11,6
NPT 02 - 8262K236S1N00
G 02 G262K129S1N00 G262K237S1N00
3,2 0,3 5 0 11 6,5 10 6,5 8,5 4,5 10,1 11,6
NPT 02 - 8262K237S1N00
G* 02 E262K161S1W00 (2) E262K199S1W00 (2)
0 79 44 62 33 55 22 10,1 11,6
NPT 02 - 8262K199S1W00 (2)
1,2 0,05 0,8
G* 02 E262K260S1N00 E262K130S1N00
0 51 44 51 38 51 27 10,1 11,6 FL FR FT F8 H1 H9
NPT 02 - 8262K130S1N00
G* 02 E262K261S1N00 E262K134S1N00
2,4 0,18 3 0 18 11 15 9 12 6,5 10,1 11,6
NPT 02 - 8262K134S1N00
G* 02 E262K262S1N00 E262K138S1N00
1/4 3,2 0,3 5 0 11 6,5 10 6,5 8,5 4,5 10,1 11,6
NPT 02 - 8262K138S1N00
G* 02 E262K263S1N00 E262K142S1N00
4 0,47 7,8 0 6 4 6 3,5 4,5 3 10,1 11,6
NPT 02 - 8262K142S1N00
G* 02 E262K264S1N00 E262K148S1N00
5,6 0,72 12 0 3 2 3 1,7 2,5 1,7 10,1 11,6
NPT 02 - 8262K148S1N00
G* 02 E262K265S1N00 E262K152S1N00
7,1 0,83 13,8 0 2 1,3 2 1,1 2 1,1 10,1 11,6
00167GB-2017/R01

NPT 02 - 8262K152S1N00
NPT 02 - 8262K230S1N01
For dimensions, see drawing(s) for each construction type on the following page(s).
(1) (2)

UR disc only, fluid temperature 0°C to+60°C, no other elastomer
() Ensure that the compatibility of the fluids in contact with the materials is verified. can be used.

All leaflets are available on: www.asco.com

6 - Solenoid Valves (2/2)
 SOLENOID VALVES SERIES 262

SPECIFICATIONS 15-DIGIT PRODUCT CODE

operating pressure voltage code
flow differential (bar)

dimensions /
orifice power coil

115 V/50 Hz
230 V/50 Hz
pipe coefficient

24 V/50 Hz
48 V/50 Hz
size max. (PS) (W) brass stainless steel

24 V/DC
48 V/DC
size Kv air () water () oil ()

type (1)
thread
min.

type
(mm) (m3/h) (l/min) ~ = ~ = ~ = ~ =
WITH MAINTAINED MANUAL OPERATOR
NC - Normally closed, NBR seal and disc
G* 02 E262K108S1N01 E262K182S1N01
40 16 28 16 28 15 10,1 11,6
NPT 02 - 8262K182S1N01
2,4 0,18 3 0
G* 02 E262K109S1N01 E262K183S1N01
49 41 28 28 28 27 17,1 22,6
NPT 02 - 8262K183S1N01
G* 02 E262K232S1N01 E262K184S1N01
23 7,5 20 7 14 6,5 10,1 11,6
NPT 02 - 8262K184S1N01
3,2 0,3 5 0
G* 02 E262K110S1N01 E262K185S1N01
34 17 26 17 24 15 17,1 22,6
NPT 02 - 8262K185S1N01
G* 02 E262K202S1N01 E262K220S1N01
14 3,5 13 3,5 10 3,5 10,1 11,6
NPT 02 - 8262K220S1N01
1/4 4 0,45 7,5 0 FL FR FT F8 H1 H9
G* 02 E262K112S1N01 E262K187S1N01
20 7,5 14 7,5 14 7,5 17,1 22,6
NPT 02 - 8262K187S1N01
G* 02 E262K208S1N01 E262K226S1N01
6,5 2 6,5 2 6,5 2 10,1 11,6
NPT 02 - 8262K226S1N01
5,6 0,63 10,5 0
G* 02 E262K114S1N01 E262K188S1N01
8,5 4 8,5 4 8,5 4 17,1 22,6
NPT 02 - 8262K188S1N01
G* 02 E262K210S1N01 E262K189S1N01
4 1,5 5 1,5 4 1,3 10,1 11,6
NPT 02 - 8262K189S1N01
7,1 0,76 12,7 0
G* 02 E262K212S1N01 E262K230S1N01
6 3 6 3 6 3 17,1 22,6
NPT 02 - 8262K230S1N01
For dimensions, see drawing(s) for each construction type on the following page(s).
(1) (2)

UR disc only, fluid temperature 0°C to+60°C, no other elastomer
() Ensure that the compatibility of the fluids in contact with the materials is verified. can be used.
Availability, design and specifications are subject to change without notice. All rights reserved.
00167GB-2017/R01

All leaflets are available on: www.asco.com

Solenoid Valves (2/2) - 7
 SOLENOID VALVES SERIES 262
15-DIGIT PRODUCT CODE Configurator - CAD Files
- 262 K 001 S1 N00 H1
Thread connection Voltage - class
G = ISO 228/1 (1/8) FL = 24 V / 50 Hz - class F
E = ISO 228/1 & ISO 7/1 (combination thread, G*) FR = 48 V / 50 Hz - class F
8 = NPT (SAE 71051) FT = 115 V / 50 Hz - class F
H = 15 mm compression fittings (2) F8 = 230 V / 50 Hz - class F
H1 = 24 V DC - class H
Product series H9 = 48 V DC - class H
262
Revision letter Options
K = Initial release Without manual operator
N00 = NBR disc and seals
V00 = FPM disc and seals
VN0 = FPM disc and seals for Oxygen service
EM0 = EPDM disc and seals, WRAS approved (2)
E00 = EPDM disc and seals
Valves version J00 = CR disc and seals
T00 = PTFE disc and seals (1)
(Max. operating pressure limited to 75% of standard
(1) 

value)
With maintained manual operator
Electrical interface & explosion proof options N01 = NBR disc and seals
S1 = With spade plug connector V01 = FPM disc and seals
FN = A luminium enclosure, 1/2 NPT conduit, IECEx/ATEX VN1 = FPM disc and seals for Oxygen service
II 2G/D Ex d IIC T6..T4 Gb / Ex tb IIIC Db IP66/IP67, zone 1-21 (equivalent to NF prefix)(3) E01 = EPDM disc and seals
FT = Aluminium enclosure, 20 mm conduit, IECEx/ATEX J01 = CR disc and seals
equivalent to NFET prefix)(3)
FS = AISI 316L enclosure, 1/2 NPT conduit, IECEx/ATEX
II 2G/D Ex d IIC T6..T4 Gb / Ex tb IIIC Db IP66/IP67, zone 1-21 (equivalent to WSNF prefix)(3)
FU = AISI 316L enclosure, 20 mm conduit, IECEx/ATEX
II 2G/D Ex d IIC T6..T4 Gb / Ex tb IIIC Db IP66/IP67, zone 1-21 (equivalent to WSNFET prefix)(3)
MV = S teel enclosure, M20 cable gland, IECEx/ATEX
II 2G Ex e mb IIC Gb T3, II2D Ex tb IIIC Db IP66/IP67, zone 1-21 (equivalent to EM prefix)(3)
MT = Steel enclosure, 20 mm conduit, IECEx/ATEX
II 2G Ex e mb IIC Gb T3, II2D Ex tb IIIC Db, zone 1-21 (equivalent to EMET prefix)(3)
MN = S teel enclosure, 1/2 NPT conduit, IECEx/ATEX
II 2G Ex e mb IIC Gb T3, II2D Ex tb IIIC Db IP66/IP67, zone 1-21 (equivalent to EMT prefix)(3)
MW = AISI 316 enclosure, M20 cable gland, IECEx/ATEX
II 2G Ex e mb IIC Gb T3, II2D Ex tb IIIC Db IP66/IP67, zone 1-21 (equivalent to WSEM prefix)(3)
MU = A ISI 316 enclosure, 20 mm conduit, IECEx/ATEX
II 2G Ex e mb IIC Gb T3, II2D Ex tb IIIC Db IP66/IP67, zone 1-21 (equivalent to WSEMET prefix)(3)
MS = A ISI 316 enclosure, 1/2 NPT conduit, IECEx/ATEX
II 2G Ex e mb IIC Gb T3, II2D Ex tb IIIC Db IP66/IP67, zone 1-21 (equivalent to WSEMT prefix)(3)
A7 = Moulded enclosure, epoxy encapsulated, integrated cable, IECEx/ATEX
II2G Ex mb IIC Gb T3(~)/T4(=), II2D Ex mb IIIC Db IP67, zone 1-21 (equivalent to PV prefix)(3)
SG = M oulded coil with connector, epoxy encapsulated, ATEX
II 3 D Ex tc IIIC T115°C Dc IP65X, zone 22 (equivalent to SG prefix)(3)

(2)
Check the online configurator for available versions on: www.asco.com
(3) 
Search prefix in asco.com to get detailed technical information.

Availability, design and specifications are subject to change without notice. All rights reserved.
Please note that the valve pressure ratings with some of the ATEX enclosures will be reduced.
To obtain the correct pressure rating please check the landing pages of the “2-Way Solenoid Valve DIN Configurator”. 00167GB-2017/R01

All leaflets are available on: www.asco.com

8 - Solenoid Valves (2/2)
 SOLENOID VALVES SERIES 262

SPARE PARTS KITS CODE ()

AC (~) DC (=)

(+ WRAS)

(+ WRAS)
EPDM

EPDM

EPDM

EPDM
(oxygen)

(oxygen)
PTFE

PTFE
+ UR

+ UR
NBR

NBR

NBR

NBR
FPM

FPM

FPM

FPM
CR

CR
E262K013/019/020/021/ M200001 N00 V00 VN0 E00 EM0 J00 T00 - M200005 N00 V00 VN0 E00 EM0 J00 T00 -
022/023/090
E262K108/109/110/112/114 M200007 N00 V00 VN0 E00 EM0 J00 T00 - M200007 N00 V00 VN0 E00 EM0 J00 T00 -
E262K130 M200017 N00 V00 VN0 E00 EM0 J00 T00 - M200033 N00 V00 VN0 E00 EM0 J00 T00 -
E262K134 M200018 N00 V00 VN0 E00 EM0 J00 T00 - M200033 N00 V00 VN0 E00 EM0 J00 T00 -
E262K138/142/148/152 M200018 N00 V00 VN0 E00 EM0 J00 T00 - M200034 N00 V00 VN0 E00 EM0 J00 T00 -
E262K161 M200021 - - - - - - - W00 - - - - - - - - -
E262K182/183/184/185/ M200008 N00 V00 VN0 E00 EM0 J00 - - M200008 N00 V00 VN0 E00 EM0 J00 - -
187/188/189
E262K200 M200007 - - - - - - - W00 M200007 - - - - - - - W00
E262K202/208/210/212 M200007 N00 V00 VN0 E00 EM0 J00 T00 - M200007 N00 V00 VN0 E00 EM0 J00 T00 -
E262K214 M200008 - - - - - - - W00 M200008 - - - - - - - W00
E262K220/226/230 M200008 N00 V00 VN0 E00 EM0 J00 - - M200008 N00 V00 VN0 E00 EM0 J00 - -
E262K232 M200007 N00 V00 VN0 E00 EM0 J00 T00 - M200007 N00 V00 VN0 E00 EM0 J00 T00 -
E262K260 M200015 N00 V00 VN0 E00 EM0 J00 T00 - M200031 N00 V00 VN0 E00 EM0 J00 T00 -
E262K261 M200016 N00 V00 VN0 E00 EM0 J00 T00 - M200031 - - - - - - - W00
E262K262/263/264/265 M200016 N00 V00 VN0 E00 EM0 J00 T00 - M200032 N00 V00 VN0 E00 EM0 J00 T00 -
G262K001/002/014/016 M200001 N00 V00 VN0 E00 EM0 J00 T00 - M200005 N00 V00 VN0 E00 EM0 J00 T00 -
G262K128 M200016 N00 V00 VN0 E00 EM0 J00 T00 - M200031 N00 V00 VN0 E00 EM0 J00 T00 -
G262K129 M200016 N00 V00 VN0 E00 EM0 J00 T00 - M200032 N00 V00 VN0 E00 EM0 J00 T00 -
G262K155 M200021 - - - - - - - W00 - - - - - - - - -
G262K156 M200015 N00 V00 VN0 E00 EM0 J00 T00 - M200031 N00 V00 VN0 E00 EM0 J00 T00 -
G262K168 M200021 - - - - - - - W00 - - - - - - - - -
G262K169 M200017 N00 V00 VN0 E00 EM0 J00 T00 - M200033 N00 V00 VN0 E00 EM0 J00 T00 -
G262K199 M200021 - - - - - - - W00 - - - - - - - - -
G262K236 M200018 N00 V00 VN0 E00 EM0 J00 T00 - M200033 N00 V00 VN0 E00 EM0 J00 T00 -
G262K237 M200018 N00 V00 VN0 E00 EM0 J00 T00 - M200034 N00 V00 VN0 E00 EM0 J00 T00 -
8262K006/007/012/015/ M200003 N00 V00 VN0 E00 EM0 J00 T00 - M200005 N00 V00 VN0 E00 EM0 J00 T00 -
036/038
8262K080/086 M200003 N00 V00 VN0 E00 EM0 J00 T00 - M200005 N00 V00 VN0 E00 EM0 J00 T00 -
8262K130 M200017 N00 V00 VN0 E00 EM0 J00 T00 - M200033 N00 V00 VN0 E00 EM0 J00 T00 -
8262K134 M200018 N00 V00 VN0 E00 EM0 J00 T00 - M200033 N00 V00 VN0 E00 EM0 J00 T00 -
8262K138/142/148/152 M200018 N00 V00 VN0 E00 EM0 J00 T00 - M200034 N00 V00 VN0 E00 EM0 J00 T00 -
8262K168 M200021 - - - - - - - W00 - - - - - - - - -
8262K169 M200017 N00 V00 VN0 E00 EM0 J00 T00 - M200033 N00 V00 VN0 E00 EM0 J00 T00 -
8262K182/183/184/185 M200008 N00 V00 VN0 E00 EM0 J00 - - M200008 N00 V00 VN0 E00 EM0 J00 - -
187/188/189
8262K199 M200021 - - - - - - - W00 - - - - - - - - -
8262K220/226/230 M200008 N00 V00 VN0 E00 EM0 J00 - - M200008 N00 V00 VN0 E00 EM0 J00 - -
8262K236 M200018 N00 V00 VN0 E00 EM0 J00 T00 - M200033 N00 V00 VN0 E00 EM0 J00 T00 -
8262K237 M200018 N00 V00 VN0 E00 EM0 J00 T00 - M200034 N00 V00 VN0 E00 EM0 J00 T00 -
() Ensure that the compatibility of the fluids in contact with the materials is verified.
Availability, design and specifications are subject to change without notice. All rights reserved.
00167GB-2017/R01

All leaflets are available on: www.asco.com

Solenoid Valves (2/2) - 9
 SOLENOID VALVES SERIES 262
MAGNETIC LATCHING VERSION
fluids () temperature range (TS) seal materials ()
water 0°C to +85°C EPDM

ELECTRICAL CHARACTERISTICS
Coil insulation class F (DC)
Standard voltages DC (=) : 3V - 6V - 9V - 12V
operator power ratings
ambient replacement coil (1)

temperature hot/cold
range (TS) = =
(W)
(°C) 640 641/642/643/644 6 V DC 12 V DC
2,5 - 400927-003 400927-005
0 to +40
- 6 400927-007 400927-014
(1) 
All coils 400 series are not UL & CSA approved.

SPECIFICATIONS 15-DIGIT PRODUCT CODE

operating pressure voltage code
flow differential (bar)

dimensions /
orifice power coil
pipe coefficient max. (PS)
size (W) brass

12 V/DC
24 V/DC
size Kv

3 V/DC
6 V/DC
9 V/DC
water ()

type (2)
thread
min.

type
(mm) (m3/h) (l/min) = =
WITHOUT MANUAL OPERATOR
EPDM seal and disc
1,2 0,05 0,8 0 10 2,5 H 03 H262K640S1EM0
15 mm 2,0 0,15 2,5 0 10 6 H 03 H262K641S1EM0
compression 3,2 0,30 5,0 0 3 6 H 03 H262K642S1EM0 CD E7 E8 F3 F1
fittings 4 0,45 7,5 0 2 6 H 03 H262K643S1EM0
6,7 0,82 13,7 0 0,7 6 H 03 H262K644S1EM0
For dimensions, see drawing(s) for each construction type on the following page(s).
(2)

() Ensure that the compatibility of the fluids in contact with the materials is verified.

15-DIGIT PRODUCT CODE Configurator - CAD Files

FOR MAGNETIC LATCHING
VERSION ONLY
H 262 K 640 S1 EM0 E7
Thread connection Voltage - class
H = 15 mm compression fittings CD = 3 V DC - class H
E7 = 6 V DC - class H
E8 = 9 V DC - class H
F3 = 12 V DC - class H
F1 = 24 V DC - class H
Product series
262
Revision letter Options
K = Initial release Without manual operator

Availability, design and specifications are subject to change without notice. All rights reserved.
EM0 = EPDM disc and seals,
Valves version WRAS approved
640 PM0 = EPDM disc and seals, Panel Mount,
641 WRAS approved
642
643
644
Electrical interface
S1 = With spade plug connector

SPARE PARTS KITS CODE ()

DC (=)
EPDM (+ WRAS)

H262K640 / H262K641
H262K642 / H262K643 M200001 EM0
H262K644
00167GB-2017/R01

All leaflets are available on: www.asco.com

10 - Solenoid Valves (2/2)
 SOLENOID VALVES SERIES 262

ACCESSORIES CODE

Mounting bracket
Steel version M200094A00
(AISI 1010 / 1.1121)

Mounting bracket
Stainless steel version M200095A00
(AISI 304 / 1.4301)

INSTALLATION
• The solenoid valves can be mounted in any position without affecting operation
• Solenoid valves have 2 mounting holes in body
• Thread connection “E” applicable for 1/4 have standard thread according to ISO 228/1 and ISO 7/1. Thread connection “G” ap-
plicable for 1/8, have standard thread according to ISO 228/1
• Thread connection “8” have standard thread = NPT (SAE 71051)
• Thread connection “H” have 1/2” male ‘G’ thread according to BS 2779 plus cap-nut and olive
• Installation/maintenance instructions are included with each valve

DIMENSIONS (mm), WEIGHT (kg) Configurator - CAD Files

TYPE 01
Electrical interface “S1”
Epoxy moulded
IEC 335 / ISO 4400
IP65
1/8, power coil 8,1 W / 10,6 W and 11,1 W / 18,6 W 1/4, power coil 8,1 W / 10,6 W and 11,1 W / 18,6 W
=
J =
17,5= =

K 1
= =

1
= 15 = A E
A E B
B C
C
Availability, design and specifications are subject to change without notice. All rights reserved.

360° 360°
F H
F H
G
G

X X
1 2 1 2
D 2 3 2 3 2
D 2

1 2 mounting holes:
pipe M5 dia., depth 6,5 mm (1/8)
type A B C D E F G H X weight (1)
size
M5 dia., depth 7,5 mm (1/4)
00167GB-2017/R01

1/8 88 51 30 30 43 62 71 88 26 0,30 2 Manual operator location

01
1/4 88 51 30 40 43 65 75 92 30 0,42
Incl. coil(s) and connector(s).
(1)

All leaflets are available on: www.asco.com

Solenoid Valves (2/2) - 11
 SOLENOID VALVES SERIES 262

DIMENSIONS (mm), WEIGHT (kg) Configurator - CAD Files

TYPE 02
Electrical interface “S1”
Epoxy moulded
IEC 335 / ISO 4400
IP65
NC: 1/4, power coil 10,1 W / 11,6 W and 17,1 W / 22,6 W NO: 1/8-1/4, power coil 10,1 W / 11,6 W
=
J

22 =
=

=
K 1
= =
1
22 =
A E
=

B A E
C B
C

360° 360°
F H
F H
G G

X X
1 2
1 2
3 2 3
D 2 2 2
D

1 
2 mounting holes:
pipe M5 dia., depth 7,5 mm (1/4)
type A B C D E F G H J K X weight (1)
size 2 
Manual operator location.
1/8 (NO) 96 59 34 30 52 67 75 88 17,5 15 26 0,50
02 1/4 (NC) 95 57 33 40 50 69 78 96 22 22 30 0,60
1/4 (NO) 96 59 34 40 52 69 78 96 22 22 30 0,62
Incl. coil(s) and connector(s).
(1)

TYPE 03
Electrical interface “S1”
Epoxy moulded
IEC 335 / ISO 4400
IP65
Magnetic latching coil 2,5 W / 6 W

Availability, design and specifications are subject to change without notice. All rights reserved.
20,5

19 1

80,5
39
45

27,5
1 2
360

Magnetic Latching version

93
65
78,5

1 2 mounting holes:
190-24 UNC-2B, depth 6 mm

weight (1)
33

0,45
00167GB-2017/R01

Incl. coil(s) and connector(s).

(1)

71,5

All leaflets are available on: www.asco.com

12 - Solenoid Valves (2/2)
 SOLENOID VALVES SERIES 262

Mounting bracket
Steel or stainless steel

M200094A00 / M200095A00
3,2 x 8
36
6.8 22,4
10,5 15
5 6,4 x 4
R6 x 2 18
F
6 17,3 21,8
52 37,7
43 35,45
9 20
1,5

36
6x 4 6,4 x 2
3,2 x 4

45
52 F 64 21,8 17,3

7,1
24,5 15 9,35
20,8 22,4
6 6 24
Availability, design and specifications are subject to change without notice. All rights reserved.
00167GB-2017/R01

All leaflets are available on: www.asco.com

Solenoid Valves (2/2) - 13
14 - Solenoid Valves (2/2)
All leaflets are available on: www.asco.com
SOLENOID VALVES SERIES 262

00167GB-2017/R01
Availability, design and specifications are subject to change without notice. All rights reserved.