Doc. No. (Rev.

) UCDS(W)_QC-002511_22-06-2021_v01_00
ULTRASONIC Form Rev. 5
CALIBRATION DATA
Date 6/28/2021
SHEET
Page 1 of 3

VERIFICATION OF EQUIPMENT (WEEKLY)

ITER VV butt welds

1. EQUIPMENT
1.1 Instrument
Model No. Manufacturer Serial number Calibration Date
Mainframe OMNISCAN-MX2 Olympus OMNI2-101098 1/26/2021
UT module OMNI-M2-PA32128PR Olympus QC-002511 1/26/2021
1.2 Probes and Wedges
TECHNIQUE T1-T3 Model No. Manufacturer Serial number
Probe 2.25DM7X4PM-19X12-A17 Olympus U4107
Wedge SA17-DN55L0-IHC Olympus ABWX2786
TECHNIQUE T5 Model No. Manufacturer Serial number
Probe 2.25DM7X4PM-19X12-A17 NOT REQUIRED
Olympus
Wedge SA17-DN55L0-IHC Olympus

2. HORIZONTAL LINEARITY (EN 12668-3, Subclause 3.2.1), 0ºL, T AUX

Full Screen Width B0 B1 B2 B3 B4 B5
Expected timebase (mm) B0 B0 + 60 B0 + 120 B0 + 180 B0 + 240 B0 + 300

Measured timebase (mm) 60.00 119.90 179.80 239.90 299.90 360.20

Deviation (mm) NA 0.1 0.2 0.1 0.1 -0.2
Results of Calibration OK
Tolerance: The deviation from linearity shall not exceed ± 2% of full screen width.

3. VERTICAL LINEARITY (ISO 18563-3, Subclause 9.4.2), 60ºL, T1 / H40, SCB-03

Expected Screen Height
Gain, dB Measured Signal Amplitude (%) Limits
(%)
2 101 101.8 Not less than 95%
0 80 80.2 (Reference line)
-6 40 40.1 37% to 43%
-12 20 19.6 17% to 23%
-18 10 9.8 8% to 12%
-24 5 4.9 Visible, below 8%
Results OK
Tolerance: The signal amplitude shall be within the limits.

VERIFIED BY: APPROVED BY:

Name: V. Gagliardi Name: D. Pavoni
Date: 6/28/2021 Date: 6/28/2021
Signature: Signature:
 Doc. No. UCDS(W)_QC-002511_22-06-2021_v01_00
ULTRASONIC Rev. 5
CALIBRATION DATA
Date 6/28/2021
SHEET
Page 2 of 3

VERIFICATION OF PROBE 2.25DM7X4PM-19X12-A17 (WEEKLY)

ITER VV butt welds

4. TECHNIQUE T1, 48ºL, H40 (BLOCK SCB-03)

4.1 Sensitivity and Signal-to-Noise (ISO 18563-3, Subclause 9.5.3)
Description Base measurement Measured values Deviation
Sensivity (dB), 20% 24.5 21.6 -2.9
Noise Gain (dB), 20% [15:70] mm 73.5 74.8 1.3
Signal-to-Noise (dB) 49.0 53.2 4.2
Result OK
4.2 Pulse Duration (EN 12668-3, Subclause 3.4.4)
Base measurement Measured values Deviation
Pulse Duration (mm), 10% / 100% 3.1 3.7 0.6
Result OK
4.3 Squint Angle (ISO 18563-3, Subclause 9.9)
Perpendicular Swivelling Deviation
Maximum Amplitude (dB), 80%FSH 33.5 33.5 0.0
Result Conform

5. TECHNIQUE T2, 60ºL, H20 (BLOCK SCB-03)

5.1 Sensitivity and Signal-to-Noise (ISO 18563-3, Subclause 9.5.3)
Description Base measurement Measured values Deviation
Sensivity (dB), 20% 28.0 24.8 -3.2
Noise Gain (dB), 20% [3:35] mm 69.5 73.8 4.3
Signal-to-Noise (dB) 41.5 44.3 2.8
Result OK
5.2 Pulse Duration (EN 12668-3, Subclause 3.4.4)
Base measurement Measured values Deviation
Pulse Duration (mm), 10% / 100% 2.5 2.9 0.4
Result OK
5.3 Squint Angle (ISO 18563-3, Subclause 9.9)
Perpendicular Swivelling Deviation
Maximum Amplitude (dB), 80%FSH 36.8 36.6 -0.2
Result Conform

6. TECHNIQUE T3, 80ºL, N11 (BLOCK SCB-03)

6.1 Sensitivity and Signal-to-Noise (ISO 18563-3, Subclause 9.5.3)
Description Base measurement Measured values Deviation
Sensivity (dB), 20% 33.0 31.1 -1.9
Noise Gain (dB), 20% [1:6] mm 75.5 72 -3.5
Signal-to-Noise (dB) 42.5 40.9 -1.6
Result OK
6.2 Pulse Duration (EN 12668-3, Subclause 3.4.4)
Base measurement Measured values Deviation
Pulse Duration (mm), 10% / 100% 0.6 0.8 0.2
Result OK
6.3 Squint Angle (ISO 18563-3, Subclause 9.9)
Perpendicular Swivelling Deviation
Maximum Amplitude (dB), 80%FSH 43.5 43.5 0.0
Result Conform

Tolerance: The sensivity and signal-to-noise ratio shall be within ± 6 dB of the base measurement.
Tolerance: The pulse duration shall not be greater than 1.5 times the base measurement.
Tolerance: The deviation for the squint angle shall be within ± 1 dB
 Doc. No. UCDS(W)_QC-002511_22-06-2021_v01_00
ULTRASONIC Rev. 5
CALIBRATION DATA
Date 6/28/2021
SHEET
Page 3 of 3

VERIFICATION OF PROBE 2.25DM7X4PM-19X12-A17 (WEEKLY)

ITER VV butt welds

7. TECHNIQUE T5, 50ºL, H40 (BLOCK SCB-03)

7.1 Sensitivity and Signal-to-Noise (ISO 18563-3, Subclause 9.5.3)
Description Base measurement Measured values Deviation
Sensivity (dB), 20% 28.0
Noise Gain (dB), 20% [15:70] mm 73.0
Signal-to-Noise (dB) NOT REQUIRED45.0
Result OK
7.2 Pulse Duration (EN 12668-3, Subclause 3.4.4)
Base measurement Measured values Deviation
Pulse Duration (mm), 10% / 100% 4.1
Result OK
7.3 Squint Angle (ISO 18563-3, Subclause 9.9)
Perpendicular Swivelling Deviation
Maximum Amplitude (dB), 80%FSH
Result Conform

Tolerance: The sensivity and signal-to-noise ratio shall be within ± 6 dB of the base measurement.
Tolerance: The pulse duration shall not be greater than 1.5 times the base measurement.
Tolerance: The deviation for the squint angle shall be within ± 1 dB