Industrial Electric Drives Linear Motion and Service Mobile

Hydraulics and Controls Assembly Technologies Pneumatics Automation Hydraulics

Inductive Position Sensor PO1 RE 95 160/12.04 1/8

Technical data sheet

Inductive sensor for position measurement

Series 2

Contents Features
– Axially-adjustable button with spring pretension
Ordering Code 2
– Inductive position sensor element according to differential
Order Number 2
throttle measuring principle
Description 3
– Integrated electronics with temperature compensation
Block Circuit Diagram / Terminal Connections 3
– Output signal, ratiometric and proportional to position
Technical Data 3
– Zero point and sensitivity matched
Characteristics 4
– Housing with M 24x1.5 external thread for fastening and
Sensor Dimensions / Pin Connections 5 alignment
Mating Connector 5 – Also available on request with 5 VDC supply voltage
Installation Position 6
Dimensions: Eccentric for Position Control 6
Safety Instructions 7
2/8 Bosch Rexroth AG Mobile Hydraulics Position Sensor PO1 RE 95 160/12.04

Ordering Code
PO1 10 / 2 0
Type
Mobile position sensor PO1

Version
Without bellows 1
With bellows 2

Characteristic
Standard S
Inverted V

Supply voltage
8 … 12 VDC 10
5 ± 0.5 VDC (on request) 05

Series
2

Index
0

Order Number
Sensors Order number
PO1 2 S 10 / 2 0 R917001941
PO1 1 S 10 / 2 0 R917001942
PO1 2 V 10 / 2 0 R917001943
PO1 1 V 10 / 2 0 R917001944

PO1 2 S 05 / 2 0 On request
PO1 1 S 05 / 2 0 On request
PO1 2 V 05 / 2 0 On request
PO1 1 V 05 / 2 0 On request
RE 95 160/12.04 Position Sensor PO1 Mobile Hydraulics Bosch Rexroth AG 3/8

Description
Position sensor PO1 is used to measure position from up to 10 mm. By mounting an eccentric onto a rotating axis the sensor can
also be used for axis stabilization of a relative position (see Page 6).
The sensor provides a ratiometric voltage with rising characteristic (Usig rises when pressed in) or inverted characteristic (Usig
drops when pressed in). For protection it can also be supplied with bellows.
This sensor is a typical part of an electronic-hydraulic hitch control (EHR).

Block Circuit Diagram / Terminal Connections

Supply voltage Usup = 8 … 12 V

Signal voltage Usig = 0.25 … 0.75 US

Ground

Technical Data
Table of values
Type PO1 position sensor
Nominal stroke 10 mm
Mechanical stroke 13 mm
Actuating force ≤ 16 N
Linearity ≤ ±2 % (cutoff point setting)
Leakage (upper cutoff point) ≤ ±1 %
Sensitivity leakage ≤ ±2.5 %
Hysteresis Not measurable
Resolution Infinite
Temp. coefficient of cutoff point ≤ ± 0.15 % / 10 °C
Temp. coefficient of sensitivity ≤ ± 0.15 % / 10 °C
Operating temperature range –30 °C … +90 °C
Storage temperature range –35 °C … +100 °C
Housing material GD-AI Si 12 (Cu)
Type of protection Coil and electronics: IP69K
Plug with fitted mating connector: IP69K (see plug table)
Mating connector 3-pin plug with grommet
Standard On request
Supply voltage Usup 8 … 12 V 5 ± 0,5 VDC
Supply current ≤ 30 mA
Signal voltage Usig (x Usup) 25 % … 75 % 10 % … 90 %
(0.5 V … 4.5 V @ 5 V)
Residual ripple < 20 mVss
Load impedance > 7 kΩ
Insulation to housing > 100 MΩ
Dielectric strength to housing < 200 V
Electromagnetic compatibility (EMC) as per 100 V/m ≤ ± 1 % Usup
ISO 11452-5 2002-04 1 MHz … 1 GHz
4/8 Bosch Rexroth AG Mobile Hydraulics Position Sensor PO1 RE 95 160/12.04

Characteristics
At 8 … 12 VDC supply voltage: Usig– useful range = 25% … 75% x Usup
Inverted Standard (rising)

10±0.6 10±0.25

75% 75%

25% 25%

13±0.6 13±0.6

s [mm] s [mm]
Out In Out In

At 5 VDC ±0.5 V supply voltage: Usig useful range = 1 VDC … 4 VDC (at 5 VDC)

10±0.6 10±0.25

4V 4V

1V 1V

13±0.6 13±0.6

s [mm] s [mm]
Out In Out In
RE 95 160/12.04 Position Sensor PO1 Mobile Hydraulics Bosch Rexroth AG 5/8

Sensor Dimensions / Pin Connections

106+1
-5 16 75
13±6 50
MA = 30 Nm ± 20%
Ø12 M24×1.5 16
4.3

Ø5-6
max Ø24

Ø16

Ø28
Ø22

16
Protective cap
5 8 Mating connector
5 14.8
28
160

Plug connections

3 + supply voltage Usup

Ø38.5

2 signal voltage Usig

1 ground

36

Mating Connector
Female connector comprising: Order number Type of protection IP67 and IP69K
Housing (1x) 1 928 402 579 *
Protective cap (1x) 1 280 703 022 *
Contacts (3x) 929 939 **
Single wire seal (3x) 828 905-1 ** for FLK cable type
(wire size: 0.5 – 1.0 mm2) (3x) 828 904-1 ** for FLKr, FLX cable
* available from Bosch
** available from AMP
The mating connector is not part of the delivery volume.
6/8 Bosch Rexroth AG Mobile Hydraulics Position Sensor PO1 RE 95 160/12.04

Installation Position
Variant 1: Inverted characteristic Variant 2: Standard (rising characteristic)

s max

Dimensions: Eccentric for Position Control

Main axis
Main axis of
eccentric disk at
raised hitching gear
e

Hitching gear
raised

e
mm
9
Sensor axis Lifting angle α
e

9mm
7 Hitching gear
60 70 80 lowered
Lifting angle α
RE 95 160/12.04 Position Sensor PO1 Mobile Hydraulics Bosch Rexroth AG 7/8

Safety Instructions
– The suggested circuits do not imply any technical liability for
the system on the part of Rexroth.
– The safety instructions contained in RDE 90 301-01 must be
observed.
– Leads to the sensors must be shielded. The shielding is to
be connected on one side to the electronic circuit or with a
low-impedance to the device or vehicle ground.
– Lines to the electronics must not be routed in the vicinity of
other power-conducting cables in the device or vehicle.
– A sufficient distance to radio systems must be maintained.
– All connectors must be unplugged from the electronics
during electrical welding operations.
8/8 Bosch Rexroth AG Mobile Hydraulics Position Sensor PO1 RE 95 160/12.04

Bosch Rexroth AG © This document, as well as the data, specifications and other informations set
Mobile Hydraulics forth in it, are the exclusive property of Bosch Rexroth AG. Without their consent
Product Unit Mobile Electronics it may not be reproduced or given to third parties.
Robert-Bosch-Straße 2 The data specified above only serve to describe the product. No statements
71701 Schwieberdingen, Germany concerning a certain condition or suitability for a certain application can be
Phone +49 (0) 711-811-4 30 80 derived from our information. The given information does not release the user
from the obligation of own judgement and verification. It must be remembered
Facsimile +49 (0) 711-811-3 36 85
that our products are subject to a natural process of wear and aging.
[email protected]
Subject to change.
www.boschrexroth.com/mobile-electronics