CIVIL WORKS FOR SV STATIONS(NON

ITEM
ITEM DESCRIPTION UNIT
NO

10 Earth work in surface excavation not exceeding 30 cm in

depth but exceeding 1.5 m in width as well as 10 sqm on
plan including getting out and disposal of
excavated earth up to 50m lead and lift up to 1.5 m, as
directed by the Engineer-in-Charge :

20 All Kind of Soil SQM

30 Earth work in excavation by mechanical means
(Hydraulic excavator)/ manual means over areas
(exceeding 30 cm in depth, 1.5 m in width as well as 10
sqm on
plan) including getting out and disposal of excavated
earth lead up to 50 m and lift up to 1.5 m, as directed by
the Engineer-in-Charge.

40 All Kind of Soil CUM

50 Filling available excavated earth (excluding rock) in CUM
trenches, plinth, sides of foundations etc. in layers not
exceeding 20 cm in depth, consolidating each deposited
layer by ramming and watering, lead up to 50 m and lift
upto 1.5 m.

60 Supplying and filling in plinth with sand under floors, CUM

including watering, ramming, consolidating and dressing
complete.
70 Clearing grass and removal of the outside the periphery SQM
of the area cleared.
80 Supplying chemical emulsion in sealed containers
including delivery as specified.
90 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% L
100 Diluting and injecting chemical emulsion for POST-
CONSTRUCTIONAL anti-termite treatment (excluding
the cost of chemical emulsion) :
110 Along external wall where the apron is not provided M
using chemical emulsion @ 7.5 litres/ sqm of the
vertical surface of the substructure to a depth of 300 mm
including excavation channel along the wall & rodding
etc. complete: With Chlorpyriphos/ Lindane E.C. 20%
with 1% concentration.

120 Treatment of soil under existing floors using chemical M

emulsion @ one litre per hole, 300 mm apart including
drilling 12 mm diameter holes and plugging with
cement mortar 1 : 2 (1 cement : 2 Coarse sand) to match
the existing floor : " with Chlorpyriphos/ Lindane E.C.
20% with 1% concentration

130 Treatment of existing masonry using chemical emulsion M

@ 1 litre per hole at 300 mm interval including drilling
holes at 45 degree and plugging them with cement
mortar 1:2 (1 cement : 2 coarse sand) to the full depth of
the hole : With Chlorpyriphos/Lindane E.C. 20% with
1% concentration

140 Extra for every additional lift of 1.5 m or part thereof in

excavation/ banking excavated or stacked materials.
150 All kinds of soil CUM
160 Supply and stacking of Fly ash conforming to IRC-58 at CUM
site, including carriage, loading, unloading & stacking
up to any lead (measured stacks will be reduced by
20% for payment).
 Filling with available fly ash and earth (excluding rock)
in trenches or embankment in layers (each layer should
not exceed 15 cm), with intermediate layer of compacted
earth (Soil density of 98%) after every four layers of
compacted depth of fly ash, sides & top layer of filling
shall be done with earth having total minimum
170 compacted thickness 30 cm or as decided by Engineer CUM
-in-charge, including compacting each layer by rolling/
ramming and watering, all complete as per
drawing and direction of the Engineer-in-Charge.

Filling the excavated earth to required grade, level &

profile in low lying areas including watering, ramming,
compacting at optimum moisture content to 90% of
Proctor's density consolidation by rolling with 8 to 10
tonne power roller in layers not exceeding 20 cm
thickness, including clearing the area by cutting of
shrubs, bushes, grass, vegetation, debris etc. stacking
180 CUM
and disposing out of plot area to an unobjectional area as
directed by site Engineer complete in all respects
inclusive of
cost of all labour, materials, tools, tackles etc. as per
drawings, specifications and direction of Site Engineer.

Supplying and filling selected earth/moorum (excluding

black cotton soil) from Contractor's own borrow areas
including royalty, with all leads and lifts in low laying
areas and filling to required grade and level including
watering, compacting at optimum moisture content to
190 90% of Proctor's density, consolidation and rolling with CUM
8 to 10 tonne power roller in layers not exceeding 20 cm
thickness, complete in all respects inclusive of cost of all
labour, materials, tools, tackles etc. as per
drawings, specifications and direction of Site Engineer.
200 Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
210 1:3:6 (1 cement : 3 coarse sand(Zone-III) : 6 graded CUM
stone aggregate 20 mm nominal size)
220 1:3:6 (1 cement : 3 coarse sand (Zone-III) : 6 graded CUM
stone aggregate 40 mm nominal size)
230 1:4:8 (1 cement : 4 coarse sand(Zone-III) : 8 graded CUM
stone aggregate 40mm nominal size)
240 Making plinth protection 50 mm thick of cement CUM
concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone
aggregate 20 mm nominal size) over 75 mm thick bed of
dry brick ballast 40 mm nominal size, well rammed and
consolidated and grouted with fine sand, including
necessary excavation, levelling & dressing & finishing
P r ovtoidpinsmg oanodthl.aying cement concrete 1:2:4 (1
t h e

cement : 2 coarse sand : 4 graded stone aggregate 10

mm down size)mixed with approved brand of water
proofing
compound @ 1Kg/50 Kg bag of cement, in roof grading,
coping, in bed concrete etc. at all heights & depths,
including providing centering and shuttering,
scaffolding, watering, curing, vibrating, etc. complete in
250 all respects inclusive of cost of all labour, materials, CUM
tools, tackles etc. as per drawings, specifications and
direction of the Site Engineer.
 Providing and laying 40 mm thick CC 1:2:4 Damp
Proof Course with cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone chips 6 mm down size) laid
to proper level & line including providing shuttering,
applying two coats of bitumen applied @ 1.50 Kg/sqm
260 and spreading an even layer of coarse sand over hot SQM
bitumen, etc. complete in all respects inclusive of cost of
all labour, materials, tools, tackles etc. as per drawings,
specifications and direction of the Site Engineer.

270 Providing and laying in position specified grade of

reinforced cement concrete, excluding the cost of
centering, shuttering, finishing and reinforcement - All
work up
to plinth level :

280 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III): 3 graded CUM

stone aggregate 20 mm nominal size)
290 1:2:4 (1 cement : 2 coarse sand : 4 graded stone CUM
aggregate 20 mm nominal size)
300 Reinforced cement concrete work in walls (any
thickness), including attached pilasters, buttresses, plinth
and string courses, fillets, columns, pillars, piers,
abutments, posts and struts etc. above plinth level up to
floor five level, excluding cost of centering, shuttering,
finishing and reinforcement :

310 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III) : 3 graded CUM

stone aggregate 20 mm nominal size)
 Reinforced cement concrete work in beams, suspended
floors, roofs having slope up to 15 Degree landings,
balconies, shelves, chajjas, lintels,bands, plain window
sills, staircases and spiral stair cases above plinth level
320 up to floor five level, excluding the cost of centering, CUM
shuttering, finishing and reinforcement, with 1:1.5:3 (1
cement : 1.5 coarse sand (Zone-III) : 3 graded stone
aggregate 20 mm nominal size)

330 Centering and shuttering including strutting, propping

etc. and removal of form for all heights :
340 Foundations, footings, bases of columns, etc. for mass SQM
concrete
350 Suspended floors, roofs, landings, balconies and access SQM
platform
360 Lintels, beams, plinth beams, girders, bressumers and SQM
cantilevers
370 Columns, Pillars, Piers, Abutments, Posts and Struts SQM
380 Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position and
binding all complete upto plinth level.
390 Thermo-Mechanically Treated bars of grade Fe-500D or Kg
more
400 Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position and
binding all complete above plinth level.
410 Thermo-Mechanically Treated bars of grade Fe-500 D Kg
or more
420 Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in foundation
and plinth in :
430 Cement mortar 1:6 (1 cement : 6 coarse sand) CUM
440 Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level in
all shapes and
sizes in :
450 Cement mortar 1:6 (1 cement : 6 coarse sand) CUM
Providing and fixing 18 mm thick gang saw cut, mirror
polished, premoulded and prepolished, machine cut for
kitchen platforms, vanity counters, window sills, facias
and similar locations of required size, approved shade,
colour and texture laid over 20 mm thick base cement
mortar 1:4 (1 cement : 4 coarse sand), joints treated with
460 white cement, mixed with matching pigment, epoxy
touch ups, including rubbing, curing, moulding and
polishing to edges to give high gloss finish etc.
complete at all levels. :Raj Nagar Plain white
marble/Udaipur green marble/Zebra black marble :

470 Area of slab up to 0.50 sqm SQM

480 Area of slab over 0.50 sqm SQM
Providing and laying Polished Granite stone flooring in
required design and patterns, in linear as well as
curvilinear portions of the building, all complete as per
the architectural drawings, with 18 mm thick stone slab
over 20 mm (average) thick base of cement mortar 1:4
(1 cement : 4 coarse sand), laid and jointed with cement
slurry and pointing with white cement slurry admixed
490 SQM
with pigment of matching shade, including rubbing,
curing and polishing etc. all complete as specified and as
directed by the Engineer-in-Charge. : Polished granite
stone slab- Jet Black, Cherry Red, Elite Brown, Cat Eye
or equivalent.
 Providing and fixing ISI marked flush door shutters
conforming to IS:2202 (Part I) non-decorative type, core
of block board construction with frame of 1st class hard
wood and well matched commercial 3 ply veneering
500 with vertical grains or cross bands and face veneers on SQM
both faces of shutters: 35 mm thick including ISI
marked
Stainless Steel butt hinges with necessary screws
510 Supplying and fixing rolling shutters of approved make, SQM
made of required size M.S. laths, interlocked together
through their entire length and jointed together at the
end by end locks, mounted on specially designed pipe
shaft with brackets, side guides and arrangements for
inside and outside locking with push and pull operation
complete, including the cost of providing and fixing
necessary 27.5 cm long wire springs manufactured from
high tensile steel wire of adequate strength conforming
to IS:4454 (Part-1) and M.S. top cover of required
thickness for rolling shutters. 80 x 1.25 mm M.S. laths
with 1.25 mm thick top cover

520 Providing and fixing ball bearing for rolling shutters. EA

Providing and fixing circular/ Hexagonal cast iron or
M.S. sheet box for ceiling fan clamp, of internal dia
140 mm, 73 mm height, top lid of 1.5 mm thick M.S.
sheet with its top surface hacked for proper bonding, top
530 lid shall be screwed into the cast iron/ M.S. sheet box by EA
means of 3.3 mm dia round headed screws, one
lock at the corners. Clamp shall be made of 12 mm dia.
M.S. bar bent to shape as per standard drawing.
 Supplying, fabricating, erecting, placing and fixing in
position M.S. structural works using rolled/ built up
sections for truss, claddings, bracings, purlins,
supporting frames made of joists, tubes, pipes, channels,
angles, plates, flats, bars etc. including cutting to
required size welding of joints, fixing anchor plates,
including bolts, theading, nuts, washers, sleeves etc.
including preparation of detailed fabrication drawings &
submission to the Engineer-in-Charge for approval
before start of fabrication, supplying & applying
painting with two coats of epoxy paint "EPILUX 155
540
High Build Enamel over a coat of "EPILUX 610" TON
Primer of M/s BERGER or any other approved
equivalent make as per manufacturer#s
recommendation, complete in all respects inclusive of
cost of all labour, materials, tools, tackles etc. as
per drawings, specifications and directions of the
Engineer-in-Charge. (Excluding the cost of concrete
work).

Supplying, fitting and fixing hot dip galvinised barbed

line wire through holes in fencing posts (already made in
the body of the post), tightening and fixing the wire
in tight condition with straining bolts (straining bolts at
end post) including the cost of cutting and lapping
550 joints, making holes, straining bolts, galvanised staples, M
binding wires etc. complete in all respects inclusive of
cost of all labour, materials, tools, tackles etc. as per
drawings, specifications and direction of the Engineer-
in- Charge.
560 Supplying and placing in position 5.0 mm thick steel SQM
chequered plates over cable ducts, valve pits etc.
including provision for lifting arrangements complete in
all
respects inclusive of cost of all labour, materials, tools,
tackles etc. as per drawings, specifications and
directions of the Engineer-in-Charge.

Supplying, fitting and fixing punched tape concertina M

spiral coil of 50 turns per coil having core wire of 2.6
mm diameter made of high carbon spring steel of high
tensile strength as per IS:4454 (Part-I, Grade-II) having
minimum galvanising coating thickness equivalent to
230 grams per square metre and low carbon steel strip of
0.5 mm thickness having a series of barbes punched all
along the length on both sides of the strip at regular
interval as per IS:513, DD quality having minimum
galvanising coating thickness of 12 microns. Hardness
570 of tape should be between 137-180 VPN (Victor
Penetration Number). The coil should be clipped
sufficiently at regular intervals. The coil should not be
stretched for more than 6.0 m length and the minimum
diameter of the coil in the closed condition should not be
less than
600 mm complete in all respects inclusive of cost of all
labour, materials, tools, tackles etc. as per drawings,
specifications and directions of the Engineer-in-Charge.

580 Providing and fixing 10 mm thick acid and/or alkali

resistant tiles of approved make and colour using acid
and/or alkali resisting mortar bedding, and joints filled
with acid and/or alkali resisting cement as per IS:4457,
complete as per the direction of Engineer-in-Charge.
590 In flooring on a bed of 10 mm thick mortar 1:4 (1 acid SQM
proof cement : 4coarse sand) Acid and alkali resistant
tile
600 In dado/ skirting on 12 mm thick mortar 1:4 (1 acid SQM
proof cement : 4 coarse sand) Acid and alkali resistant
610 tile
Kota stone slabs 20 mm thick in risers of steps, skirting, SQM
dado and pillars laid on 12 mm (average) thick cement
mortar 1:3 (1 cement: 3 coarse sand) and jointed with
grey cement slurry mixed with pigment to match the
shade of the slabs, including rubbing and polishing
complete.

620 Kota stone slab flooring over 20 mm (average) thick SQM

base laid over and jointed with grey cement slurry mixed
with pigment to match the shade of the slab, including
rubbing and polishing complete with base of cement
mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing first quality ceramic glazed wall

tiles conforming to IS:15622 (thickness to be specified
by the manufacturer), of approved make, in all colours,
shades except burgundy, bottle green, black of any size
as approved by the Engineer-in-Charge, in skirting,
630 risers of steps and dados, over 12 mm thick bed of SQM
cement mortar 1:3 (1 cement : 3 coarse sand) and
jointing with grey cement slurry @ 3.3 Kg/sq.m.,
including pointing in white cement mixed with pigment
of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size

300x300 mm (thickness to be specified by the
manufacturer) of first quality conforming to IS:15622 of
approved make in colours such as White, Ivory, Grey,
Fume Red Brown, laid on 20 mm thick cement mortar
640 1:4 (1 Cement : 4 Coarse sand), jointing with grey SQM
cement slurry @ 3.3 Kg/sq.m. including pointing the
joints with white cement and matching pigment, etc.
complete.
 Providing and fixing first quality ceramic glazed floor
tiles conforming to IS:15622 (thickness to be specified
by the manufacturer) of approved make in all colours,
shades except burgundy, bottle green, black of any size
as approved by Engineer-in-Charge in skirting, risers of
650 steps and dados over 12 mm thick bed of cement Mortar SQM
1:3 (1 cement: 3 coarse sand) and jointing with grey
cement slurry @ 3.3 Kg/sq.m. including pointing in
white cement mixed with pigment of matching shade
complete.

Providing and laying vitrified floor tiles in different

sizes (thickness to be specified by the manufacturer)
with water absorption less than 0.08% and conforming
to IS:15622, of approved make, in all colours and
660 shades, laid on 20 mm thick cement mortar 1:4 (1
cement : 4 coarse sand), jointing with grey cement slurry
@ 3.3
Kg/sq.m. including grouting the joints with white
cement and matching pigments etc., complete.
670 Size of Tile 500x500 mm SQM
680 Size of Tile 600x600 mm SQM
Providing and laying Vitrified tiles in different sizes
(thickness to be specified by manufacturer), with water
absorption less than 0.08 % and conforming to
IS:15622,
690 of approved make, in all colours & shade, in skirting,
riser of steps, over 12 mm thick bed of cement mortar
1:3 (1 cement: 3 coarse sand), jointing with grey cement
slurry @ 3.3 Kg/sq.m. including grouting the joint with
white cement & matching pigments etc. complete.
700 Size of Tile 500x500 mm SQM
710 Size of Tile 600x600 mm SQM
720 Supplying and laying flat brick soling in foundation SQM
trench, in floors, garages, sumps, etc., with bricks of
class designation 50 laid to proper slope, level and grade
etc. filling of the joints with sand etc. complete in all
respects inclusive of cost of all labour, materials, tools,
tackles etc. as per drawings, specifications and direction
of the Site Engineer.

Providing and laying 52 mm thick cement concrete

flooring with metallic hardner, under layer of 37 mm
thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) and top
layer of 15 mm thick metallic concrete hardner
consisting of mix 1:2 (1 cement : 2 stone aggregate 6
mm nominal size) by volume with which metallic
hardening compound such as IRONITE NO. 1 of
730 IRONITE CO. OF INDIA LTD. or aproved equivalent SQM
mixed in the ratio 4:1 (4 parts of cement : 1 part of
metallic floor hardening compound of approval quality)
by weight, inclusive of cost of finishing, labour,
material, equipment,
etc. as per specifications and directions of the Engineer-
in-Charge.

740 Providing gola 75x75 mm in cement concrete 1:2:4 (1 M

cement : 2 coarse sand : 4 stone aggregate 10 mm and
down gauge), including finishing with cement mortar
1:3 (1 cement : 3 fine sand) as per standard design : In
75x75 mm deep chase
 Making Khurras 45x45 cm with average minimum
thickness of 5 cm cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate of 20 mm
nominal size) over P.V.C. sheet 1 m x 1 m x 400
750 micron, finished with 12 mm cement plaster 1:3 (1 EA
cement : 3 coarse sand) and a coat of neat cement,
rounding the edges
and making and finishing the outlet complete.

760 Providing and fixing on wall face Unplasticised Rigid M

PVC (UPVC) rainwater pipes conforming to IS:13592
Type-A, including jointing with seal ring conforming to
IS:5382, leaving 10 mm gap for thermal expansion: (i)
Single socketed pipes : 110 mm diameter
770 Providing and fixing on wall faceUnplasticised-PVC
(UPVC) moulded fittings/ accessories for Un-plasticised
Rigid PVC rainwater pipes conforming to IS:13592
Type A, including jointing with seal ring conforming to
IS:5382, leaving 10 mm gap for thermal expansion :
780 Coupler : 110 mm EA
790 Single Push-fit Coupler : 110 mm` EA
800 Bend 87.5 Degrees : 110 mm bend EA
810 Shoe (Plain) : 110 mm shoe EA
820 15 mm cement plaster on the rough side of single or half
brick wall of mix :
830 1:4 (1 cement : 4 fine sand) SQM
840 1:6 (1 cement : 6 fine sand) SQM
850 15 mm cement plaster on rough side of single or half
brick wall of mix :
860 1:6 (1 cement : 6 coarse sand) SQM
870 6 mm cement plaster of mix :
880 1:3 (1 cement : 3 fine sand) SQM
890 6 mm cement plaster 1:3 (1 cement : 3 fine sand) SQM
finished with a floating coat of neat cement and thick
coat of Lime wash on top of walls when dry for bearing
of
R.C.C. slabs and beams
900 Applying one coat of water thinnable cement primer of SQM
approved brand and manufacture on wall surface :Water
thinnable cement primer
910 Finishing walls with textured exterior paint of required SQM
shade : New work (Two or more coats applied @ 3.28
ltr/10 sqm) over and including priming coat of exterior
primer applied @ 2.20kg/10 sqm
920 Applying priming coat : With ready mixed red oxide SQM
zinc chromate primer of approved brand and
manufacture on steel galvanised iron/ steel works.
930 Wall painting with acrylic emulsion paint of approved SQM
brand and manufacture to give an even shade : Two or
more coats on new work
940 Providing and applying white cement Rs. based putty of SQM
average thickness 1 mm, of approved brand and
manufacturer, over the plastered wall surface to prepare
the
surface even and smooth complete.
950 Distempering with 1st quality acrylic distemper, having SQM
VOC (Volatile Organic Compound) content less than
50 grams/ litre, of approved brand and manufacture,
including applying additional coats wherever required,
to achieve even shade and colour. Two coats
960 Painting with synthetic enamel paint, having VOC SQM
(Volatile OrganicCompound) content less than 150
grams/ litre, of approved brand andmanufacture,
including
applying additional coats wherever required toachieve
even shade and colour.

970 Providing grooves of uniform size 12x12 M

980 Providing & fixing galvanized chicken wire net 20 SQM
Gauge, 20 mm mesh size in plastering work at the
junction of RCC Columns/ Beams & brickwork as
directed by
the Engineer-in-Charge.
Providing and laying Burnt Terracota Tiles 12 mm thick
for facia, over walls, sloping RCC Roofs etc. at all levels
and locations laid over and including a backing coat of
15 mm thick cement mortar (1 cement : 3 sand) and
990 joints filled with coloured cement of same colour as tiles SQM
complete in all respects inclusive of cost of all
labour, materials, tools, tackles etc. as per specifications
and directions of the Engineer-in-Charge

Providing and fixing 12 mm thick Elevational Brick

Tiles for facia, vertical face of walls, etc. at all levels
and locations laid over and including a backing coat of
15
1000 mm thick cement mortar (1 cement : 3 sand) and joints SQM
filled with coloured cement of same colour as tiles
complete in all respects inclusive of cost of all labour,
materials, tools, tackles etc. as per specification and
directions of the Engineer-in-Charge.
 Demolishing cement concrete manually/ by mechanical
means including disposal of material within 50 metres
lead as per direction of the Engineer-in-Charge. [Notes:
(1) Dismantling shall be allowed during day shift only &
prior permission for the same shall be obtained. (2)
1010 Providing of necessary covers/ barricades CUM
around the work area shall be done prior to dismantling
operations.]Nominal concrete 1:3:6 or richer mix
(including equivalent design mix)

1020 Demolishing R.C.C. work manually/ by mechanical CUM

means including stacking of steel bars and disposal of
unserviceable material within 50 metres lead as per
direction of the Engineer-in-Charge. [Notes: (1)
Dismantling shall be allowed during day shift only &
prior permission for the same shall be obtained. (2)
Providing of necessary covers/ barricades around the
work area shall be done prior to dismantling operations.
(3) Cutting of all reinforcement shall be done using hack
saw or
chiesel or any other method as approved by the
Engineer-in-Charge.]

Demolishing brick work manually/ by mechanical

means including stacking of serviceable material and
disposal of unserviceable material within 50 metres lead
as
1030 per direction of the Engineer-in-Charge. [Notes: (1)
Dismantling shall be allowed during day shift only &
prior permission for the same shall be obtained. (2)
Providing of necessary covers/ barricades around the
work area shall be done prior to dismantling operations.]
1040 In cement mortar CUM
 Dismantling manually/ by mechanical means including
stacking of serviceable material and disposal of
unserviceable material within 50 metres lead as per
direction of the Engineer-in-Charge. [Notes: (1)
Dismantling shall be allowed during day shift only &
prior permission for the same shall be obtained. (2)
1050 Providing of necessary covers/ barricades around the
work area shall be done prior to dismantling operations.
(3) Adequate safety precautions shall also be taken care
before
commencement of any activity.]

1060 Bituminous Road SQM

1070 Preparation and consolidation of sub-grade with power SQM
road roller of 8 to 12 tonne capacity after excavating
earth to an average of 22.5 cm depth, dressing to
camber and consolidating with road roller including
making good the undulations etc. and re-rolling the sub
grade and disposal of surplus earth with lead up to 50
metres.

1080 Supplying and stacking at site :

1090 90 mm to 45 mm size stone aggregate CUM
1100 Supplying and stacking at site :
1110 53 mm to 22.4 mm size stone aggregate CUM
Laying, spreading and compacting stone aggregate of
specified sizes to WBM specifications in uniform
thickness, hand picking, rolling with 3 wheeled road/
vibratory roller 8-10 tonne capacity in stages to proper
1120 grade and camber, applying and brooming requisite type CUM
of screening/ binding material to fill up interstices of
coarse aggregate, watering and compacting to the
required density.
1130 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 CUM
graded stone aggregate 40 mm nominal size) in
pavements, laid to required slope and camber in panels
as
required including consolidation finishing and tamping
complete.

Providing and laying design mix cement concrete of M-

30 grade in roads/ taxi tracks/ runways, using cement
content as per design mix, using coarse sand and graded
stone aggregate of 40 mm nominal size in appropriate
proportions as per approved & specified design criteria,
providing dowel bars with sleeve/ tie bars wherever
required, laying at site, spreading and compacting
mechanically by using needle and surface vibrators,
levelling to required slope/ camber, finishing with
required texture, including steel form work with sturdy
M.S. channel sections, curing, making provision for
1140 contraction/ expansion, construction & longitudinal CUM
joints (10 mm wide x 50 mm deep) by groove cutting
machine, providing and filling joints with approved joint
filler and sealants, complete all as per direction of the
Engineer-in- Charge. [Notes: (1) Item of joint fillers,
sealants, dowel bars with sleeve/ tie bars to be paid
separately. (2) Cement content considered in M-30 is @
340 kg/cum.
Excess/ less cement used as per design mix is payable/
recoverable separately]. Cement concrete prepared with
batch mixing machine

1150 Providing and fixing in position pre-moulded joint filler M

in expansion joints.
Note: Measurement shall be done in "PER CM DEPTH
PER CM WIDTH PER M LENGTH"
1160 Providing and laying factory made chamfered edge
Cement Concrete paver blocks In foot path, park &
lawns driveway or light & traffic parking etc. of
required
strength, thickness & size/ shape, made by table
vibratory method using PU mould, laid in required
colour & pattern over 50mm thick compacted bed of
course sand, compacting and proper embedding/laying
of inter locking paver blocks into the sand bedding layer
through vibratory compaction by using plate vibrator,
filling the joints with sand and cutting of paver blocks as
per required size and pattern, finishing and sweeping
extra sand, all complete as per manufacturer's
specifications & direction of the Engineer-in-Charge.

1170 60mm thick Cement Concrete paver block of M-35 SQM

grade with approved colour, design & pattern.
Providing and fixing white vitreous china pedestal type
water closet (European type W.C. pan) with seat and lid,
10 litre low level white P.V.C. flushing cistern,
including flush pipe, with manually controlled device
1180 (handle lever), conforming to IS:7231, with all fittings EA
and fixtures complete, including cutting and making
good the walls and floors wherever required :W.C. pan
with ISI marked white solid plastic seat and lid.
 Providing and fixing white vitreous china flat back or
wall corner type lipped front urinal basin of
430x260x350 mm and 340x410x265 mm sizes
respectively with automatic flushing cistern with
standard flush pipe and C.P. brass spreaders with brass
1190 unions and G.I clamps complete, including painting of EA
fittings and brackets,
cutting and making good the walls and floors wherever
required : One urinal basin with 5 litre white P.V.C.
automatic flushing cistern

1200 White Vitreous China Flat back wash basin size EA

550x400 mm with single 15 mm C.P. brass pillar tap
1210 Providing and fixing P.V.C. waste pipe for sink or wash EA
basin including P.V.C. waste fittings complete : Semi
Rigid Pipe : 32 mm diameter
1220 Providing and fixing 600x450 mm beveled edge mirror EA
of superior glass (of approved quality) complete with 6
mm thick hard board ground fixed to wooden cleats
with C.P. brass screws and washers complete.
1230 Providing and fixing toilet paper holder C.P. Brass EA
(Ref. Make: JAQUAR, Model: Cat. No.-1151 or
approved equivalent).
1240 Re-painting sand cast iron/ centrifugally cast iron (spun) M
iron, soil, waste, vent pipes and fittings with one coat of
synthetic enamel paint of any colour such as
chocolate, grey or buff, etc. : 75 mm diameter pipe
 Providing and fixing Polyethelene-Aluminium-
Polyethelene (PE-AL-PE) Composite Pressure Pipes
conforming to IS-15450, U.V. stabilized with carbon
black having thermal stability for hot & cold water
supply, capable to withstand temperature up to 80°C,
including all special fittings of composite material
(engineering plastic blend and brass inserts wherever
1250
required) e.g. elbows, tees, reducers, couplers &
connectors etc., with clamps at 1.00 metre spacing. This
includes testing of
joints complete as per direction of the Engineer-in-
Charge.

1260 2025 (25 mm OD) pipe M

1270 2532 (32 mm OD) pipe M
Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply, including all CPVC plain & brass threaded
fittings, including fixing the pipe with clamps at 1.00 m
1280 spacing. This includes jointing of pipes & fittings with
one step CPVC solvent cement and testing of joints
complete as per direction of the Engineer-In-Charge.

1290 15 mm nominal outer dia pipes M

1300 20 mm nominal outer dia pipes M
Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply, including all CPVC plain & brass threaded
fittings, i/c fixing the pipe with clamps at 1.00 m
1310 spacing. This includes jointing of pipes & fittings with
one step CPVC solvent cement and the cost of cutting
chases and making good the same including testing of
joints complete as per direction of the Engineer-In-
Charge.
1320 15 mm nominal outer dia pipes M
1330 20 mm nominal outer dia pipes M
1340 Fixing water meter and stop cock in G.I. pipe line EA
including cutting and threading the pipe and making
long screws etc. complete (cost of water meter and stop
cock
to be paid separately).
1350 Providing and fixing gun metal gate valve with
C.I.wheel of approved quality(screwed end)
1360 25 mm nominal bore EA
1370 32 mm nominal bore EA
1380 Providing and placing on terrace (at all floor levels) L
polyethylene water storage tank (Ref. Make: SINTEX or
approved equivalent), IS:12701 marked, with cover and
suitable locking arrangement and making necessary
holes for inlet, outlet and overflow pipes but without
fittings and the base support for tank. Rectangular Tank

1390 Providing and fixing C.P. brass long nose bib cock of EA
approved quality conforming to IS standards and
weighing not less than 810 gms. 15 mm nominal bore
Providing and fixing 15mm diameter C.P. brass tap as
per following with C.P. brass flange including cutting &
making good the walls wherever required, etc. complete
in all respects inclusive of cost of all materials, labour,
1400 tools, tackles etc. as per specifications and directions of EA
the Engineer-in-Charge. : Bib Cock (Ref.
Make: JAQUAR, Model: Cat. No. 0021 or approved
equivelent)
 Providing and fixing 15mm diameter C.P. brass angle
valve as per following with C.P. copper connecting pipe
375mm long or as required including nuts, washers,
C.P. brass flange, etc. including cutting & making good
the walls wherever required, etc. complete in all respects
1410 inclusive of cost of all materials, labour, tools, tackles EA
etc. as per specifications and directions of the Engineer-
in-Charge. Angle Valve (Ref. Make: JAQUAR, Model:
Cat. No. 0053 or approved equivalent)

Providing and fixing 15mm diameter C.P. brass stop

cock with wall flange (Ref. Make: JAQUAR, Model:
Cat. No. 0933 or approved equivalent), male end with
C.P. copper connecting pipe 375mm long or as required
including nuts, washers, C.P. brass flange etc. including
1420 cutting & making good the walls wherever required EA
complete in all respects inclusive of cost of all materials,
labour, tools, tackles etc. as per specifications and
directions of the Engineer-in-Charge.

1430 Providing & fixing Angle Valve (Ref. Make: JAQUAR, EA

Model: Cat. No. 563 or approved equivalent) and Health
Faucet with flexible tube 8mm diameter x 1.5 m
long (Ref. Make: JAQUAR, Model: Cat. No. 549 or
approved equivalent).

1440 Providing and fixing the following washroom fittings,

complete in all respects; inclusive of cost of all
materials, labour, tools, tackles etc. as per specifications
and
directions of the Engineer-in-Charge.
1450 Stainless steel liquid soap container (spring loaded push EA
type) with lid and brackets fixed to P.V.C. cleats with
C.P. brass screws, etc.
1460 C.P. brass double coat hook (Ref. Make: JAQUAR, EA
Model: Cat. No. 1161 or approved equivalent).
1470 Providing, laying and jointing glazed stoneware pipes
Class SP-1 with stiff mixture of cement mortar in the
proportion of 1:1 (1 cement : 1 fine sand) including
testing of joints etc. complete :
1480 150 mm diameter M
1490 200 mm diameter M
1500 250 mm diameter M
Providing and fixing square-mouth S.W. gully trap class
SP-1 complete with C.I. grating brick masonry chamber
with water tight C.I. cover with frame of 300x300 mm
size (inside) the weight of cover to be not less than 4.50
1510 kg and frame to be not less than 2.70 kg as per standard EA
design : 100x100 mm size P-type : With
common burnt clay F.P.S. (Non-modular) bricks of class
designation 7.5

1520 Providing and laying non-pressure NP-2 class (light

duty) R.C.C. pipes with collars jointed with stiff mixture
of cement mortar in the proportion of 1:2 (1 cement : 2
fine sand) including testing of joints etc. complete :
1530 250 mm dia. R.C.C. pipe M
1540 300 mm dia. R.C.C. pipe M
1550 500 mm dia. R.C.C. pipe M
 Constructing brick masonry chamber for underground
C.I. inspection chamber and bends with bricks in
cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover
with frame (light duty) 455x610 mm internal
dimensions, total weight of cover with frame to be not
less than 38 kg (weight of cover 23 Kg and weight of
frame 15 Kg), R.C.C. top slab with 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size), foundation concrete 1:5:10 (1 cement
: 5 coarse sand (Zone-III) : 10 graded stone aggregate 40
1560 EA
mm nominal size), inside plastering 12 mm thick with
cement mortar 1:3 (1 cement : 3 coarse sand), finished
smooth with a floating coat of neat cement on walls and
bed concrete etc. complete as per standard design :Inside
dimensions 455x610 mm and 45 cm deep for single
pipeline :
With common burnt clay F.P.S. (Non-modular) bricks of
class designation 7.5

1570 Making soak pit 2.5 m diameter 3.0 metre deep with 45 EA
x 45 cm dry brick honey comb shaft with bricks and
S.W. drain pipe 100 mm diameter, 1.8 m long
complete as per standard design :With common burnt
clay F.P.S. (Non-modular) bricks of class designation
7.5
Constructing brick masonry Septic Tank with brickwork
in cement mortar 1:6 including R.C.C. 1:2:4 (1 cement :
2 sand : 4 graded coarse aggregate) top slab, C.I. cover
all as per standard drawing, etc. complete in all respects
1580 inclusive of cost of all materials, labour, tools, tackles EA
etc. as per drawings, specifications and
directions of the Engineer-in-Charge. For 10 Users
1590 Constructing percolation pit of size 3.0m diameter and EA
2.0m deep, filled with 40 mm size brick ballast
including providing suitable pre-cast RCC covers with
lifting lugs, laying of 150mm diameter x 5.0m long
U.P.V.C. pipe embedded in pit/ outlet pipe all complete
as per specification and directions of the Engineer-in-
Charge.
Providing and fixing self cleaning S.C.I. heavy quality
Floor/ Nahani trap with 100mm diameter inlet and
100mm diameter outlet, 125mm C.P. brass grating
(heavy type) with or without vent arm including cost of
cutting and making good the walls and floors, jointing
1600 with lead caulked joints, connecting with waste water EA
pipe etc. complete in all respects inclusive of cost of all
materials, labour, tools, tackles etc. as per drawings,
specifications and directions of the Engineer-in-Charge.

1610 Providing and fixing 32mm diameter (Nominal Bore) EA

brass ball valve of approved quality complete with high
pressure copper floats, complete in all respects
inclusive of cost of all materials, labour, tools, tackles,
etc. complete as per specifications and directions of the
Engineer-in-Charge.
 Construction of second class brick masonary open
surface drain (Size: 200mm wide & 200mm average
depth) in cement mortar 1:4 laid over a bed of 150mm
thick cement concrete 1:3:6 (1 cement : 3 coarse sand : 6
graded stone aggregate 20 mm nominal size) including
making haunches and providing 15mm thick cement
plaster in CM 1:4 (1 cement : 4 coarse sand) with a
floating coat of neat cement inside and its top and
1620 exposed surfaces, including excavatioin, disposal of the M
surplus earth up to any lead and lift as per standard
design and drawing, complete in all respects inclusive of
cost of all labour, materials, carriages, excavation and
refilling, curing etc., as per specifications of the
Engineer-in-Charge.

Constructing Brick Masonary catch pit in cement mortar

1:4 (1 cement : 4 coarse sand) including necessary
excavation, 200mm thick foundation concrete 1:3:6 mix
(1 cement : 3 coarse sand : 6 graded stone aggregate
40mm size) and inside and top plastering (15mm thick)
with cement mortar 1:4 (1 cement : 4 coarse sand)
1630 finished with a floating coat of neat cement making
necessary connections to drains inclusive of all labour,
material, equipment, etc., all complete as per drawing
and
directions of the Engineer-in-Charge.

1640 750mm x 750mm x depth up to 1000mm inner EA

dimensions
1650 600mm x 600mm x depth up to 750mm inner EA
dimensions
 Boring, providing and installation bored cast-in-situ
reinforced cement concrete piles of grade M-25 of
specified diameter and length below the pile cap, to
carry a
safe working load not less than specified, excluding the
cost of steel reinforcement but including the cost of
boring with bentonite solution and temporary casing of
appropriate length for setting out and removal of same
and the length of the pile to be embedded in the pile cap
1660 etc. by percussion drilling using Direct mud circulation M
(DMC) or Bailer and chisel technique by tripod and
mechanical Winch Machine all complete, including
removal of excavated earth with all its lifts and leads
[Notes: (1) Length of pile for payment shall be measured
up to bottom of pile cap. (2) Truck Mounted rotary/
TMR/ Tubewell boring machine shall not be

Boring with hydraulic piling rigs with power units,

providing and installing cast in situ single under
reamed piles of specified diameter and length below pile
cap in
M-25 cement concrete, to carry a safe working load not
1670 less than specified, excluding the cost of steel M
reinforcement but including the cost of boring with
bentonite solution and the length of the pile to be
embedded in pile cap etc. all complete. (Length of pile
for payment shall be measured upto to the bottom of pile
cap) : 300 mm diameter piles
 Vertical load testing of piles in accordance with IS:2911
(Part-IV) including installation of loading platform by
Kentledge/ Anchor piles method and preparation of pile
head or construction of test cap and dismantling of test
cap after test etc. complete as per specification & the
direction of the Engineer-In-Charge. [Notes : (1) Initial
and Routine Load Test shall not be carried out by
1680 EA
Dynamic method of testing. (2) Testing agency shall
submitt the design of loading platform for the approval
of the Engineer-In-Charge.] :Single pile up to 50 tonne
Safe Capacity : Initial Test (Test Load 2.5 times the Safe
Capacity)

1690 Vertical load testing of piles in accordance with IS:2911 EA

(Part-IV) including installation of loading platform by
Kentledge/ Anchor piles method and preparation of pile
head or construction of test cap and dismantling of test
cap after test etc. complete as per specification & the
direction of the Engineer-In-Charge. [Notes : (1) Initial
and Routine Load Test shall not be carried out by
Dynamic method of testing. (2) Testing agency shall
submitt the design of loading platform for the approval
of the Engineer-In-Charge.] : Single pile up to 50 tonne
Safe Capacity : Routine Test (Test Load 1.5 times the
Safe Capacity)
 Providing and fixing aluminium work for doors,
windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections and
other sections of
approved make conforming to IS:733 and IS:1285,
fixing with dash fasteners of required dia and size,
including necessary filling up the gaps at junctions, i.e.
at top, bottom and sides with required EPDM rubber/
neoprene gasket etc. Aluminium sections shall be
1700 smooth, rust free, straight, mitred and jointed Kg
mechanically wherever required including cleat angle,
Aluminium snap beading for glazing / paneling, C.P.
brass / stainless steel screws, all complete as per
architectural drawings and the directions of the
Engineer-In-Charge. (Glazing, paneling and dash
fasteners to be paid for separately) : For fixed portion :
Powder coated aluminium
 Providing and fixing aluminium work for doors,
windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections and
other sections of approved make conforming to IS:733
and IS:1285, fixing with dash fasteners of required dia
and size, including necessary filling up the gaps at
junctions, i.e. at top, bottom and sides with required
EPDM rubber/ neoprene gasket etc. Aluminium sections
shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle,
Aluminium snap beading for glazing / paneling, C.P.
1710 brass / stainless steel screws, all complete as per Kg
architectural drawings and the directions of the
Engineer-In-Charge. (Glazing, paneling and dash
fasteners to be paid for separately) : For shutters of
doors, windows & ventilators including providing and
fixing hinges/ pivots and making provision for fixing of
fittings wherever required including the cost of EPDM
rubber/ neoprene gasket required. (Fittings shall be paid
for separately) :Powder coated aluminium (Minimum
thickness of powder coating 50 micron)

1720 Providing and fixing glazing in aluminium door, SQM

window, ventilator shutters and partitions etc. with
rubber/ neoprene gasket etc. complete as per the
architectural drawings and the directions of Engineer-In-
Charge. (Cost of aluminium snap beading shall be paid
in basic item) :With float glass panes of 5.50 mm
thickness
 Providing and fixing double action hydraulic floor
spring of approved brand and manufacture conforming
to IS:6315, having brand logo embossed on the body/
plate with double spring mechanism and door weight up
to 125 Kg, for doors, including cost of cutting floors,
embedding in floors as required and making good the
1730 same matching to the existing floor finishing and cover EA
plates with brass pivot and single piece M.S. sheet outer
box with slide plate etc. complete as per the direction of
Engineer-In-Charge. : With stainless steel cover plate
minimum 1.25 mm thickness

1740 Providing and fixing aluminium tubular handle bar 32 EA

mm outer dia, 3.0 mm thick & 2100 mm long with SS
screws etc .complete as per direction of the Engineer-In-
Charge. Powder coated (Minimum thickness 50 micron)
aluminium tubular handle bar

1750 Providing and fixing 100 mm brass locks (best make of EA

approved quality) for aluminium doors including
necessary cutting and making good etc. complete.
1760 Providing and fixing aluminium casement windows EA
fastener of required length for aluminium windows with
necessary screws etc. complete. Powder coated
(Minimum thickness 50 micron) Aluminium
1770 Providing and fixing, on fixed glazing/ doors/ window SQM
panes, sun control film "HP NATURAL 35 SAFETY
COMBINATION FILM-4Mil" of M/s. GARWARE or
approved equivalent make and shade, all complete as per
manufacturer's specification and as per instructions of
the Engineer-in-Charge.
 Providing and laying APP (Atactic Rs.Polypropylene
Polymer) modified prefabricated five layer, 3 mm thick
water proofing membrane, black finished reinforced
with non-woven polyester matt consisting of a coat of
bitumen primer for bitumen membrane @ 0.40 litre/sqm
by the same membrane manufacture of density at 25°C,
0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the
primer coat the layer of membrane shall be laid using
Butane Torch and sealing all joints etc, and preparing
the surface complete. The vital physical and chemical
parameters of the membrane shall be as under : (a) Joint
1780 strength in longitudinal and transverse direction at 23°C SQM
as 650/450N/5cm. (b) Tear strength in longitudinal and
transverse direction as 300/250N. (c) Softening point of
membrane not less than 150°C. (d) Cold flexibility shall
be up to -2°C when tested in accordance with ASTM, D-
5147. The laying of membrane shall be got done through
the authorised applicator of
the manufacturer of membrane : 3 mm thick

1790 Supplying and using water proofing compound like Kg

CICO, PUDDLE or any other approved brand with
Cement Plaster/ CC/ RCC complete in all respects
inclusive
of cost of all labour, materials, tools, tackles etc. as per
drawings, specifications and direction of the Site
Engineer.

1800 Supplying, filling, spreading & leveling stone boulders CUM

of size range 5 cm to 20 cm, in recharge pit, in the
required thickness, for all leads & lifts, all complete as
per
direction of the Engineer-In-Charge.
1810 Supplying, filling, spreading & leveling gravels of size CUM
range 5 mm to 10 mm, in the recharge pit, over the
existing layer of boulders, in required thickness, for all
leads & lifts, all complete as per direction of the
Engineer-In-Charge.

1820 Supplying, filling, spreading & leveling coarse sand of CUM

size range 1.5 mm to 2 mm in recharge pit, in required
thickness over gravel layer, for all leads & lifts, all
complete as per direction of the Engineer-In-Charge.
Supplying and providing non-shrinkable cement grout
(SHRINKKOMP 20 or any other equivalent approved
brand) for grouting holding down bolts in pocket holes
for equipment foundation, including necessary surface
1830 preparation mixing of grout, curing as per Kg
manufacturer's recommendation/ specification and
direction of the
Site Engineer. (Note: This item shall be operated under
specific instruction of the Engineer-in-Charge.)
Providing and fixing 75mm diameter P.V.C. pipe (4
Kg/sq.cm) for Weep Holes in Masonry/ RCC wall
including providing 230x230x230 mm size (approx.)
filter
1840 using pebles of 40mm & down size in every weep hole M
on retaining side etc. complete in all respects inclusive
of cost of all materials, labour, tools, tackles etc. as per
specifications and directions of the Engineer-in-Charge.

Total Values
S FOR SV STATIONS(NON ITC)

Qty LIKHITA TOTAL RBS TOTAL ME

190 38.03 7225.70 15.00 2850.00 40.00

0.00

658 90.70 59680.60 110.00 72380.00 99.00

500

90.70 45350.00 90.00 45000.00 99.00

17
1277.33 21714.61 805.00 13685.00 1277.00

1900
9.12 17328.00 0.00 9.00

0.00
50 133.86 6693.00 155.00 7750.00 147.00
 0.00

132

12.43 1640.76 14.00 1848.00 13.00

150

95.09 14263.50 115.00 17250.00 104.00

200

13.90 2780.00 16.00 3200.00 15.00

0.00
5 37.30 186.50 0.00 40.00
1500

93.63 140445.00 115.00 172500.00 102.00

1500 90.70 136050.00 45.00 67500.00 99.00

1500 107.52 161280.00 125.00 187500.00 118.00

1500 346.70 520050.00 325.00 487500.00 346.00

 0.00

17
4196.95 71348.15 4500.00 76500.00 4197.00
15
3832.00 57480.00 4300.00 64500.00 3832.00
75
3649.52 273714.00 4200.00 315000.00 3650.00
5

4379.42 21897.10 3500.00 17500.00 4380.00

7 5200.57 36403.99 6200.00 43400.00 5700.00

132 395.06 52147.92 485.00 64020.00 430.00

0.00 0.00

150
5656.76 848514.00 5700.00 855000.00 5656.00
5
5018.09 25090.45 5500.00 27500.00 5018.00

0.00 0.00

15
6021.71 90325.65 6400.00 96000.00 6021.00
 80 6204.20 496336.00 6500.00 520000.00 6205.00

0.00 0.00
212
139.59 29593.08 150.00 31800.00 150.00
175
303.82 53168.50 300.00 52500.00 335.00
677
247.26 167395.02 250.00 169250.00 270.00
487 336.67 163958.29 250.00 121750.00 365.00

0.00 0.00

14500
6.38 92510.00 6.00 87000.00 7.00

0.00 0.00

15200
6.38 96976.00 6.00 91200.00 7.00

0.00 0.00

35 5018.09 175633.15 4500.00 157500.00 5018.00

 0.00 0.00

250 5291.80 1322950.00 5300.00 1325000.00 5291.00

0.00 0.00

2.5 1403.25 3508.13 7000.00 1535.00

2800.00
5 2413.25 12066.25 0.00 2645.00

22 2114.90 46527.80 2500.00 55000.00 2320.00

2.5 1123.14 2807.85 1500.00 3750.00 1230.00

10

1666.92 16669.20 2050.00 20500.00 1825.00

5 272.80 1364.00 350.00 1750.00 295.00

5 93.06 465.30 125.00 625.00 105.00

 2 76792.29 153584.58 85000.00 170000.00 84200.00

480 338.49 162475.20 50.00 24000.00 370.00

 37

3242.60 119976.20 3500.00 129500.00 3550.00

200

294.50 58900.00 350.00 70000.00 320.00

0.00

17
772.79 13137.43 925.00 15725.00 845.00
22
822.97 18105.34 950.00 20900.00 900.00
0

891.39 0.00 850.00 0.00 975.00

833.01 0.00 1000.00 0.00 915.00

24 535.56 12853.44 650.00 15600.00 585.00

15 495.43 7431.45 625.00 9375.00 540.00

0 2796.45 0.00 625.00 0.00 2796.00

0.00 0.00

0 1140.48 0.00 0.00 1140.00

1000.00
72 1186.09 85398.48 0.00 1186.00

0.00 0.00

0 722.61 0.00 0.00 790.00

1025.00
0 817.49 0.00 0.00 895.00
150

409.66 61449.00 425.00 63750.00 450.00

17 648.70 11027.90 800.00 13600.00 710.00

102

110.40 11260.80 125.00 12750.00 120.00

 6 135.03 810.18 150.00 900.00 145.00

30

169.70 5091.00 225.00 6750.00 185.00

0.00 0.00

10 72.99 729.90 95.00 950.00 80.00

10 68.43 684.30 90.00 900.00 75.00
10 82.12 821.20 100.00 1000.00 90.00
10 69.34 693.40 95.00 950.00 75.00
0.00 0.00
0 164.23 0.00 175.00 0.00 164.00
1900 159.67 303373.00 175.00 332500.00 160.00
0.00 0.00
790 173.36 136954.40 175.00 138250.00 175.00
0.00 0.00
60 103.10 6186.00 125.00 7500.00 110.00
250

138.68 34670.00 150.00 37500.00 150.00

400
25.55 10220.00 33.00 13200.00 30.00

650

107.66 69979.00 135.00 87750.00 120.00

25
20.99 524.75 0.00 25.00

2000
60.22 120440.00 75.00 150000.00 70.00

400

62.04 24816.00 75.00 30000.00 65.00

400

36.50 14600.00 45.00 18000.00 35.00

 0

53.83 0.00 65.00 0.00 53.00

0 46.08 0.00 55.00 0.00 46.00

170

140.51 23886.70 175.00 29750.00 155.00

0 1122.23 0.00 1400.00 0.00 1122.23

0 852.16 0.00 1050.00 0.00 852.00

5 718.04 3590.20 0.00 780.00

1047.41 5237.05 0.00 1150.00

0.00 0.00

10 606.74 6067.40 0.00 665.00

 0.00 0.00

5 126.83 634.15 155.00 775.00 140.00

370

65.09 24083.30 65.00 24050.00 75.00

0.00 0.00
75 961.65 72123.75 1250.00 93750.00 1050.00
0.00 0.00
57 1110.37 63291.09 1400.00 79800.00 1215.00

132 322.98 42633.36 395.00 52140.00 355.00

14

3963.38 55487.32 4900.00 68600.00 4345.00

43 4963.35 213424.05 6200.00 266600.00 5440.00

30

1.46 43.80 2.00 60.00 1.46

 0.00 0.00

100
543.78 54378.00 650.00 65000.00 595.00

1 2461.60 2461.60 3100.00 3100.00 2462.00

0 2515.43 0.00 3100.00 0.00 2515.00

0
1308.35 0.00 1500.00 0.00 1308.00
2
52.66 105.32 71.00 142.00 53.00

588.49 1176.98 650.00 1300.00 640.00

2
276.45 552.90 285.00 570.00 300.00

10.94 54.70 14.00 70.00 12.00

 0.00 0.00

15 189.77 2846.55 225.00 3375.00 205.00

15 250.90 3763.50 305.00 4575.00 270.00

0.00 0.00

10 103.10 1031.00 135.00 1350.00 105.00

10 128.65 1286.50 175.00 1750.00 140.00

0.00 0.00

15 177.00 2655.00 240.00 3600.00 190.00

15 204.37 3065.55 265.00 3975.00 220.00
3

249.99 749.97 325.00 975.00 250.00

0.00 0.00
0 308.39 0.00 400.00 0.00 308.00
0 360.39 0.00 475.00 0.00 360.00
500

5.12 2560.00 7.00 3500.00 5.00

0
399.63 0.00 475.00 0.00 399.00

0 963.47 0.00 1300.00 0.00 963.00

5 995.41 4977.05 1351.00 6755.00 1045.00

0 1029.16 0.00 1395.00 0.00 1029.00

1848.48 0.00 2500.00 0.00 1848.00

0.00 0.00

0
1323.86 0.00 1750.00 0.00 1323.00

2
674.25 1348.50 900.00 1800.00 705.00
 0.00 0.00

0 235.39 0.00 319.00 0.00 235.00

0 304.73 0.00 413.00 0.00 304.00
0 498.16 0.00 665.00 0.00 498.00

0 1154.16 0.00 1565.00 0.00 1154.00

0.00 0.00

0 346.70 0.00 471.00 0.00 346.00

0 373.16 0.00 500.00 0.00 373.00
20 684.29 13685.80 929.00 18580.00 750.00
1 3439.67 3439.67 4500.00 4500.00 3665.00

14892.78 14892.78 20000.00 20000.00 16300.00

1 80399.84 80399.84 98000.00 98000.00 88000.00

2

51398.92 102797.84 61000.00 122000.00 56300.00

5 1030.99 5154.95 1400.00 7000.00 1130.00

3794.59 0.00 4500.00 0.00 3795.00

78 1200.70 93654.60 1300.00 101400.00 1315.00

0.00 0.00

3
10116.47 30349.41 11000.00 33000.00 11090.00
3 7951.40 23854.20 9500.00 28500.00 8715.00
320 1076.61 344515.20 1300.00 416000.00 1185.00

480 1542.84 740563.20 1600.00 768000.00 1690.00

1 27769.19 27769.19 35000.00 30435.00

35000.00
1

12547.05 12547.05 0.00 13750.00

105 277.36 29122.80 350.00 36750.00 305.00
138 320.25 44194.50 400.00 55200.00 350.00

27

722.61 19510.47 950.00 25650.00 790.00

8 1478.97 11831.76 1700.00 13600.00 1625.00

364.95 2919.60 350.00 2800.00 405.00

8
258.20 2065.60 300.00 2400.00 283.00

40.15 321.20 0.00 40.00

27

659.65 17810.55 895.00 24165.00 725.00

175 300.17 52529.75 350.00 61250.00 330.00

192

83.03 15941.76 95.00 18240.00 90.00

663.30 3316.50 900.00 4500.00 730.00

5

747.24 3736.20 1000.00 5000.00 820.00

747.24 3736.20 1000.00 5000.00 820.00

0 42.43 0.00 55.00 0.00 42.00

60 181.56 10893.60 245.00 14700.00 200.00

9044799.96 9292955.00
814031.996 836365.95
814031.996 836365.95
10672863.95 10965686.90
292822.95 226596.93
519419.89
TOTAL

7600.00

0.00

65142.00

49500.00

21709.00

17100.00

0.00
7350.00
 0.00

1716.00

15600.00

3000.00

0.00
200.00

153000.00
148500.00

177000.00

519000.00
 0.00

71349.00

57480.00

273750.00

21900.00

39900.00
56760.00

0.00

848400.00

25090.00

0.00

90315.00
496400.00

0.00

31800.00

58625.00

182790.00
177755.00

0.00

101500.00

0.00

106400.00

0.00

175630.00
 0.00

1322750.00

0.00

3837.50
13225.00

51040.00
3075.00

18250.00

1475.00

525.00
168400.00

177600.00
131350.00

64000.00

0.00

14365.00
19800.00

0.00

0.00

14040.00

8100.00
 0.00

0.00

0.00
85392.00

0.00

0.00
0.00
67500.00

12070.00

12240.00
 870.00

5550.00

0.00

800.00
750.00
900.00
750.00
0.00
0.00
304000.00
0.00
138250.00
0.00
6600.00
37500.00

12000.00

78000.00

625.00

140000.00

26000.00

14000.00
 0.00

0.00

26350.00

0.00

0.00
3900.00

5750.00

0.00

6650.00
 0.00

700.00

27750.00

0.00
78750.00
0.00
69255.00

46860.00
60830.00

233920.00

43.80
 0.00

59500.00

2462.00
 0.00

0.00

106.00

1280.00

600.00

60.00
 0.00

3075.00
4050.00

0.00

1050.00
1400.00

0.00

2850.00
3300.00

750.00

0.00
0.00
0.00

2500.00

0.00

0.00
5225.00

0.00

0.00

0.00

0.00

1410.00
 0.00

0.00
0.00
0.00

0.00

0.00

0.00
0.00
15000.00
3665.00

16300.00

88000.00
112600.00

5650.00

0.00
102570.00

0.00

33270.00
26145.00
379200.00

811200.00
30435.00

13750.00
32025.00
48300.00

21330.00
13000.00

3240.00

2264.00

320.00

19575.00
57750.00

17280.00

3650.00
 4100.00

4100.00

0.00

12000.00

9484986.30
853648.767
853648.767
11192283.83