Scribd
Upload
109 views

05 - Etc - PPT (Compatibility Mode)

The document discusses various components of a cable system including a connection PCB, RPD, rotary encoder, chime connection, and limit switch. It provides details on the names and functions of components, wiring diagrams, and technical specifications.

Uploaded by

Moises Perello
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
109 views

05 - Etc - PPT (Compatibility Mode)

The document discusses various components of a cable system including a connection PCB, RPD, rotary encoder, chime connection, and limit switch. It provides details on the names and functions of components, wiring diagrams, and technical specifications.

Uploaded by

Moises Perello
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

1 / 12

T-Cable

◆ T-Cable

Control panel side  CA, CB, CC, CD, CE


Car top side  CCA, CCB, CCC, CCD, AIR1

 TR < 80 m

 TR ≥ 80 m
2 / 12
Connection PCB

◆ Connection PCB

LR
3 / 12
Connection PCB

◆ Connection PCB Name Description Pin No.

OL Observation light 5
CDRPR Rear door power(220Vac) 5
SOCK Socket power 5
IOB Rear door signal 8
JP4 Door signal 8
PTM Potential meter 4
JP5 Safety shoe/photo input 4
JP3 Chime input 4
PSPO Photo power(SMPS) 4
JP6 Weighing device input 4
LIGHT Car light 5
CDRP Front door power(220Vac) 5
DMR Rear door signal 8
DM Door signal 8
JP9 PTM input 4
SES Safety Edge Switch 4
JP8 Light relay 4
PSES Photo 4
WD Weighing Device 5
FAN Fan power 5
4 / 12
Connection PCB

◆ Connection PCB

Name Description Pin No. Name Description Pin No.


EMPU Emergency Power Unit 5 PSPI SMPS power 5
PHOTO Photo power 5 LEV Leveling Device 4
SCS Safety Catch Switch 2 SPEAKER Spare 4
TOC4 Safety line(TCI-ERO,SCS) 4 INT Interphone 4
TOC2 Inspection run, safety line 6 CN8 EM unit 4
JP1 CPI_to SM.02 H 6 CHIME Chime 4
COP1 CPI_to SM.02 G 6 JP100 Spare 4
CDS Car Door Switch 2 MHS Man Hole Switch 2
CDSR Car door switch(Rear) 2 TOC3 24Vdc 4
CCA Safety line, car light, EMPU 21 TOC1 Inspection run 4
CCB Inspection run, 1/2LV 9 COP2 Inspection run, safety line 21
CCC Interphone 9 PE1 Board GND 4
CCD CPI_from Controller 6 JP101 Spare 4
CP1 CPI_to sub CPI 6 EMPU Emergency Power Unit 5
5 / 12
RPD

◆ RPD
6 / 12
RPD

◆ RPD Magnet
7 / 12
RPD

◆ RPD Magnet
8 / 12
RPD

◆ RPD

20 mm

Leveling input signal status must be activated below.


 Up direction: X15(down) and then X14(up)
 Down direction: X14 and then X15
9 / 12
Rotary Encoder

◆ Rotary Encoder

(PG CARD AS.T010).

Remove
10 / 12
Rotary Encoder

◆ Rotary Encoder
11 / 12
Chime Connection

◆ Chime

Jumper

Taping

SM.02/I PCB JP3

1. Remove JP3.1 and insulate bare copper wire.


2. Check if JP3.5 is energized by DC22V (The point of 0V is JP3.1)
3. Connect JP3.5 into CHIME-02 (Original cable shall be disconnected before new wiring)
12 / 12
Limit Switch

◆ Slow Down Switch

Speed
Switch name
60 m/min 90 m/min 105 m/min
SLDL (SLUL) 150 mm 150 mm 150 mm
SLDT (SLUT) 30 ~ 50 mm 30 ~ 50 mm 30 ~ 50 mm
SSD (SSU)
SSD (SSU) 1,200 mm 2,400 mm 2,600 mm

SLDT (SLUT)

SLDL (SLUL)
13 / 12
Limit Switch

◆ Slow Down Switch

SSD (SSU)

1,200 mm

Bottom Floor

30~50 mm SLDT (SLUT)

150 mm

SLDL (SLUL)

( In case of 60 m/min )

 Switch position should be set at position which is little lower than normal deceleration distance

You might also like