Calculation Sheet

Job Design Office

Floatation Check Date Job No.
Verifier Page No.
Box - Underpass Date

Road Level (or Ground Level)

h5

h3
h7
h6 WT
θ H1 h4
Column
β H2
Backfill Pavement
Level
Rock failure

h1
h2
b1 B b1

Parameters Input:
Internal height of the underpass, H1 = 6.347 m
Road Level, RL = 12.215 m Over all height of structure, H2 = 8.747 m
Water Table, RL = 12.215 m Over all width of structure, B = 14.100 m
Pavement Level, RL = 2.403 m Width of Heel, b1 = 2.000 m
Depth of base slab, h1 = 1.200 m
3
Unit weight of water, γw = 10.00 kN/m Depth of pavement, h2 = 0.200 m
3
Unit weight of r/f concrete, γc = 25.00 kN/m Depth of roof slab, h3 = 1.000 m
3
Unit weight of mass concrete, γc = 24.00 kN/m Thickness of wall, h4 = 1.200 m
3
Unit weight of backfill,γ's = 20.00 kN/m Backfill height on the roof slab, h5 = 2.465 m
Average soil friction, S = 0.00 kN/m2 Backfill height on the heels, h6 = 10.012 m
Wedge failure angle, θ = 10.00 deg Water table height, h7 = 0.000 m
Unit weight of rock = 0.00 kN/m3
Rock failure angle, β = 0.00 deg
3
Unit weight of pavement, γp = 20.00 kN/m
Weight of the structure:
W1 = 1288.320 kN/m length

Weight of Pavement Fill:

W2 = 46.800 kN/m length

Weight of backfill on the roof: (maximum 1m height of backfill is omitted for floatation calculation)
W3 = 206.565 kN/m length

Weight of backfill on the Heels: (Mass concrete backfill on heel is assumed)

W4 = 1208.846 kN/m length

Shear resistance at rock interface or backfill load due to rock failure:

W5 = 0.000 kN/m length (whichever less is considered)
backfill load due to rock failure, W5 = 0 kN/m length
Uplift Force under the base slab: Shear resistance at rock face, S1 = 0 kN/m length
U = 2029.37 kN/m length

Restrained Force: Where, Partial Safety Factors

R = W1 / γf2 + W2 / γf2 + W3 / γf1 + W4 / γf1 + S1 / γm1 (or W5/γf1) for soil, γf1 = 1.2
= 2340.48 kN/m length for weight of structure, γf2 = 1.15
for shear resistance, γm1 = 2
R/U = 1.153 PASS Assumptions:
- Unit length of the box is considered for floatation check
- Friction from side walls are omitted
- Top 1m height of soil is omitted for backfill load calculation against floatation
- Internal columns weight is omitted in the weight calculation
- Holding tank weight and water weight are omitted in the weight calculation
 Calculation Sheet

Job Design Office

Floatation Check Date Job No.
Verifier Page No.
Approach Ramp - Section 1 (7 to 9m height) Date
Type-4
h5
Ground Level
T2

h4
WT
θ
β h3
Backfill Pavement
Level
Rock failure

h1
h2 T1
b1 B b1

Parameters Input:

Ground Level, RL = 8.800 m Internal width of structure, B = 11.700 m

Water Table, RL = 8.800 m Width of Heel, b1 = 2.000 m
Pavement Level, RL = 0.000 m Depth of base slab, h1 = 2.000 m
Depth of pavement, h2 = 0.200 m
3
Unit weight of water, γw = 10.00 kN/m Height of wall, h3 = 8.500 m
3
Unit weight of r/f concrete, γc = 25.00 kN/m Wall thicknessl, T1 = 1.650 m
3
Unit weight of mass concrete, γ'c = 24.00 kN/m Wall thickness, T2 = 1.650 m
3
Unit weight of backfill,γ's = 20.00 kN/m Water table height, h4 = 0.000 m
Average soil friction, S = 0.00 kN/m2 h5 = 0.500 m
Wedge failure angle, θ = 10.00 deg
Unit weight of rock = 0.00 kN/m3
Rock failure angle, β = 0.00 deg
3
Unit weight of pavement, γp = 20.00 kN/m
Weight of the structure:
W1 = 1651.250 kN/m length

Weight of Pavement Fill:

W2 = 46.800 kN/m length

Weight of backfill on the Heels: (Mass concrete backfill on heel is assumed)

W3 = 1038.838 kN/m length

Shear resistance at rock interface or backfill load due to rock failure:

W5 = 0.000 kN/m length (whichever less is considered)
backfill load due to rock failure, W5 = 0 kN/m length
Uplift Force under the base slab: Shear resistance at rock face, S1 = 0 kN/m length
U = 2090.00 kN/m length

Restrained Force: Where, Partial Safety Factors

R = W1 / γf2 + W2 / γf2 + W3 / γf1 + W4 / γf1 + S1 / γm1 (or W5/γf1) for soil, γf1 = 1.2
= 2342.26 kN/m length for weight of structure, γf2 = 1.15
for shear resistance, γm1 = 2

R/U = 1.121 PASS

Assumptions:
- Unit length of the ramp is considered for floatation check
- Friction from side walls are omitted
- Top 1m height of soil is omitted for backfill load calculation against floatation
 Calculation Sheet

Job Design Office

Floatation Check Date Job No.
Checked Page No.
Approach Ramp - Section 2 (4 to 7m height) Date
Type-3
h5
Ground Level
T2

h4
WT
θ
β h3
Backfill Pavement
Level
Rock failure

h1
h2 T1
b1 B b1

Parameters Input:

Ground Level, RL = 6.800 m Internal width of structure, B = 11.700 m

Water Table, RL = 6.800 m Width of Heel, b1 = 2.100 m
Pavement Level, RL = 0.000 m Depth of base slab, h1 = 2.000 m
Depth of pavement, h2 = 0.200 m
3
Unit weight of water, γw = 10.00 kN/m Height of wall, h3 = 6.500 m
3
Unit weight of r/f concrete, γc = 25.00 kN/m Wall thicknessl, T1 = 1.300 m
3
Unit weight of mass concrete, γ'c = 24.00 kN/m Wall thickness, T2 = 1.300 m
3
Unit weight of backfill,γ's = 20.00 kN/m Water table height, h4 = 0.000 m
Average soil friction, S = 0.00 kN/m2 h5 = 0.500 m
Wedge failure angle, θ = 10.00 deg
Unit weight of rock = 0.00 kN/m3
Rock failure angle, β = 0.00 deg
3
Unit weight of pavement, γp = 20.00 kN/m
Weight of the structure:
W1 = 1347.500 kN/m length

Weight of Pavement Fill:

W2 = 46.800 kN/m length

Weight of backfill on the Heels: (Mass concrete backfill on heel is assumed)

W3 = 757.147 kN/m length

Shear resistance at rock interface or backfill load due to rock failure:

W5 = 0.000 kN/m length (whichever less is considered)
backfill load due to rock failure, W5 = 0 kN/m length
Uplift Force under the base slab: Shear resistance at rock face, S1 = 0 kN/m length
U = 1665.00 kN/m length

Restrained Force: Where, Partial Safety Factors

R = W1 / γf2 + W2 / γf2 + W3 / γf1 + W4 / γf1 + S1 / γm1 (or W5/γf1) for soil, γf1 = 1.2
= 1843.39 kN/m length for weight of structure, γf2 = 1.15
for shear resistance, γm1 = 2

R/U = 1.107 PASS

Assumptions:
- Unit length of the ramp is considered for floatation check
- Friction from side walls are omitted
- Top 1m height of soil is omitted for backfill load calculation against floatation
 Calculation Sheet

Job Design Office

Floatation Check Date Job No.
Checked Page No.
Approach Ramp - Section 3 (2 to 4m height) Date
Type-2
h5
Ground Level
T2

h4
WT
θ
β h3
Backfill Pavement
Level
Rock failure

h1
h2 T1
b1 B b1

Parameters Input:

Ground Level, RL = 3.800 m Internal width of structure, B = 11.700 m

Water Table, RL = 3.800 m Width of Heel, b1 = 0.000 m
Pavement Level, RL = 0.000 m Depth of base slab, h1 = 2.550 m
Depth of pavement, h2 = 0.200 m
3
Unit weight of water, γw = 10.00 kN/m Height of wall, h3 = 3.500 m
3
Unit weight of r/f concrete, γc = 25.00 kN/m Wall thicknessl, T1 = 1.300 m
3
Unit weight of mass concrete, γ'c = 24.00 kN/m Wall thickness, T2 = 1.300 m
3
Unit weight of backfill,γ's = 20.00 kN/m Water table height, h4 = 0.000 m
Average soil friction, S = 0.00 kN/m2 h5 = 0.500 m
Wedge failure angle, θ = 10.00 deg
Unit weight of rock = 0.00 kN/m3
Rock failure angle, β = 0.00 deg
3
Unit weight of pavement, γp = 20.00 kN/m
Weight of the structure:
W1 = 1139.125 kN/m length

Weight of Pavement Fill:

W2 = 46.800 kN/m length

Weight of backfill on the Heels: (Mass concrete backfill on heel is assumed)

W3 = 0.000 kN/m length

Shear resistance at rock interface or backfill load due to rock failure:

W5 = 0.000 kN/m length (whichever less is considered)
backfill load due to rock failure, W5 = 0 kN/m length
Uplift Force under the base slab: Shear resistance at rock face, S1 = 0 kN/m length
U = 936.65 kN/m length

Restrained Force: Where, Partial Safety Factors

R = W1 / γf2 + W2 / γf2 + W3 / γf1 + W4 / γf1 + S1 / γm1 (or W5/γf1) for soil, γf1 = 1.2
= 1031.24 kN/m length for weight of structure, γf2 = 1.15
for shear resistance, γm1 = 2

R/U = 1.101 PASS

Assumptions:
- Unit length of the ramp is considered for floatation check
- Friction from side walls are omitted
- Top 1m height of soil is omitted for backfill load calculation against floatation

Calculation Sheet
Job Design Office
Floatation Check Date Job No.
Checked Page No.
Approach Ramp - Section 4 (below 2m in height) Date
Type-1
h5
Ground Level
T2

h4
WT
θ
β h3
Backfill Pavement
Level
Rock failure

h1
h2 T1
b1 B b1

Parameters Input:

Ground Level, RL = 1.800 m Internal width of structure, B = 11.700 m

Water Table, RL = 1.800 m Width of Heel, b1 = 0.000 m
Pavement Level, RL = 0.000 m Depth of base slab, h1 = 1.400 m
Depth of pavement, h2 = 0.200 m
3
Unit weight of water, γw = 10.00 kN/m Height of wall, h3 = 1.500 m
3
Unit weight of r/f concrete, γc = 25.00 kN/m Wall thicknessl, T1 = 0.800 m
3
Unit weight of mass concrete, γ'c = 24.00 kN/m Wall thickness, T2 = 0.800 m
3
Unit weight of backfill,γ's = 20.00 kN/m Water table height, h4 = 0.000 m
Average soil friction, S = 0.00 kN/m2 h5 = 0.500 m
Wedge failure angle, θ = 10.00 deg
Unit weight of rock = 0.00 kN/m3
Rock failure angle, β = 0.00 deg
3
Unit weight of pavement, γp = 20.00 kN/m
Weight of the structure:
W1 = 525.500 kN/m length

Weight of Pavement Fill:

W2 = 46.800 kN/m length

Weight of backfill on the Heels: (Mass concrete backfill on heel is assumed)

W3 = 0.000 kN/m length

Shear resistance at rock interface or backfill load due to rock failure:

W5 = 0.000 kN/m length (whichever less is considered)
backfill load due to rock failure, W5 = 0 kN/m length
Uplift Force under the base slab: Shear resistance at rock face, S1 = 0 kN/m length
U = 452.20 kN/m length

Restrained Force: Where, Partial Safety Factors

R = W1 / γf2 + W2 / γf2 + W3 / γf1 + W4 / γf1 + S1 / γm1 (or W5/γf1) for soil, γf1 = 1.2
= 497.65 kN/m length for weight of structure, γf2 = 1.15
for shear resistance, γm1 = 2

R/U = 1.101 PASS

Assumptions:
- Unit length of the ramp is considered for floatation check
- Friction from side walls are omitted
- Top 1m height of soil is omitted for backfill load calculation against floatation

Calculation Sheet

Job Design Office

 Floatation Check Date Job No.
Checked Page No.
Approach Ramp - Section 51+CH160) Date

h5
Ground Level
T2

h4
WT
θ
β h3
Backfill Pavement
Level
Rock failure

h1
h2 T1
b1 B b1

Parameters Input:

Ground Level, RL = 8.800 m Internal width of structure, B = 11.700 m

Water Table, RL = 8.800 m Width of Heel, b1 = 1.200 m
Pavement Level, RL = 0.000 m Depth of base slab, h1 = 1.500 m
Depth of pavement, h2 = 0.200 m
3
Unit weight of water, γw = 10.00 kN/m Height of wall, h3 = 8.500 m
3
Unit weight of r/f concrete, γc = 25.00 kN/m Wall thicknessl, T1 = 1.500 m
3
Unit weight of mass concrete, γ'c = 24.00 kN/m Wall thickness, T2 = 1.500 m
3
Unit weight of backfill,γ's = 20.00 kN/m Water table height, h4 = 0.000 m
Average soil friction, S = 0.00 kN/m2 h5 = 0.500 m
Wedge failure angle, θ = 10.00 deg
Unit weight of rock = 0.00 kN/m3
Rock failure angle, β = 0.00 deg
3
Unit weight of pavement, γp = 20.00 kN/m
Weight of the structure:
W1 = 1278.750 kN/m length

Weight of Pavement Fill:

W2 = 46.800 kN/m length

Weight of backfill on the Heels: (Mass concrete backfill on heel is assumed)

W3 = 731.638 kN/m length

Shear resistance at rock interface or backfill load due to rock failure:

W5 = 0.000 kN/m length (whichever less is considered)
backfill load due to rock failure, W5 = 0 kN/m length
Uplift Force under the base slab: Shear resistance at rock face, S1 = 0 kN/m length
U = 1795.50 kN/m length

Restrained Force: Where, Partial Safety Factors

R = W1 / γf2 + W2 / γf2 + W3 / γf1 + W4 / γf1 + S1 / γm1 (or W5/γf1) for soil, γf1 = 1.2
= 1762.35 kN/m length for weight of structure, γf2 = 1.15
for shear resistance, γm1 = 2

R/U = 0.982 FAIL

Assumptions:
- Unit length of the ramp is considered for floatation check
- Friction from side walls are omitted
- Top 1m height of soil is omitted for backfill load calculation against floatation