7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

Pub. No. EE14E-11162

SERVICE MANUAL REPAIR SERVICE

& MAINTENANCE

VRZ

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 1/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

WARNINGS
The following definitions and warning signs are used in this service manual.
These are extremely important to safe operation.
Important points are described to prevent bodily injury and property damage.
They must be fully understood before beginning VRZ maintenance.

CAUTION
CAUTION!! Improper maintenance can result in injury and property damage.

MEANINGS OF MARKS
The following marks are used in this service manual to facilitate correct VRZ maintenance.

Advice Procedures that must be performed to enable the best possible VRZ
maintenance.
Note Information assisting in the best possible VRZ maintenance.

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 2/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

FOREWORD
This service manual describes the disassembly, The contents of the manual, including
inspection, reassembly and adjustment of the illustrations, drawings and specifications were
VRZ (radial plunger system position-control the latest available at the time of printing.
distributor type fuel injection pump). The right is reserved to make changes in
Refer to the separate service manuals listed specifications and procedures at any time
below to facilitate VRZ type injection pump without notice.
maintenance.
This manual is intended for use by vehicle BOSCH K.K.
maintenance technicians or persons with an Sales Automotive Aftermarket Division
adequate knowledge of injection pumps.

Service manual Publication number

VRZ Construction and Operation EE14E-11150
INJECTION PUMP TEST BENCH 10NP & 20 NP, Operation EC18E-11081
CONTINUOUS MEASURING DEVICE ZCM & ZCD, Operation EC18E-11091
CONTROLLER ASSEMBLY MC-02, FOR VRZ & COVEC-F EC14E-11022
WITH EEP-ROM, Operation
MC-02 TESTER SOFTWARE, ADJUSTMENT AND INSPECTION ED14E-11011
DATA, FOR VRZ AND COVEC-F WITH EEP-ROM, Installation

ECU ASSEMBLY, ADJUSTMENT AND INSPECTION DATA, ED14E-11021

FOR VRZ AND COVEC-F WITH EEP-ROM, Installation

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 3/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 4/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

SERVICE PRECAUTIONS

[1] Carrying the injection pump

 Never knock or drop the injection pump
when carrying it.

Injection pump

P-VRZR- 320

• When carrying the injection pump, hold the

GE actuator
pump by the bottom of the pump body.

CAUTION
Never hold the pump by the GE actuator or
the harnesses.
Holding the pump by these components may
result in damage or injury.
Wire harness

Pump body
P-VRZR- 321

GE actuator
[2] Disassembly and reassembly
• Only the mechanical components of the
injection pump body can be disassembled
and reassembled.
Advice
Do not disassemble the GE actuator other
than directed in this manual.
• The GE actuator consists of electrical
components. Do not damage them.

Injection pump
P-VRZR- 322

Harness connectors • When cleaning the injection pump, do not

GE actuator clean the GE actuator, the harnesses, or the
harness connectors using fuel oil. Use only
clean waste cloth.

Wire harness

Injection pump
P-VRZR- 323

-1-
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 5/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

SPECIAL TOOLS

1. DISASSEMBLY, INSPECTION AND REASSEMBLY TOOLS

[1] Tool use locations

20 21 18 31 30

19
32
34
10
22
33

7
9
27
24

6
26 29
13

8 15

11
14

12

37

28 25
36
23 16
3, 4

5
1
17

35

P-VRZR- 324

-2-
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 6/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 7/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

SPECIAL TOOLS

Key
RBAJ part no Bosch part no Part name Qty Remarks
no
30 157915-9700 9 681 610 686 Socket 1 For removing and installing pump support
bracket (T50)

31 157928-4800 9 442 612 302 Plate 1 For temporarily holding feed pump
32 157917-4920 9 681 610 711 Wrench 1 For turning auxiliary gear
33 157977-8000 9 681 610 829 Adapter 1 For inlet piping
34 026512-1640 9 421 617 041 Gasket 3 For inlet piping
35 157971-0500 9 443 613 408 Clip 1 For fixing plunger
36 157924-8520 9 681 611 028 Base 1 Stand for installing drive gear
37 157928-4400 9 442 612 371 Pliers 1 For removing and installing drive gear snapring

-4-
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 8/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 9/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

SPECIAL TOOLS

10. 157928-4120 11. 157829-3520 12. 157845-8900

(9 442 612 299) (9 681 610 171) (9 681 610 626)
Extractor Measuring device Adapter

13. 105782-4530 14. 157917-4620 15. 157848-2300

(9 680 610 094) (9 681 610 710) (9 681 611 027)
Measuring device Wrench Oil seal guide

46

25 75

16. 157926-2421 17. 157927-4500 18. 157928-5820

(9 681 610 773) (9 443 613 008) (9 443 613 397)
Extractor Puller Hook

-6-
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 10/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

SPECIAL TOOLS

19. 157928-3120 20. 157928-3620 21. 157928-4200

(9 442 612 297) (9 442 612 298) (9 442 612 369)
Clip Holder Guide

22. 157928-4500 23. 157928-4700 24. 105782-4540

(9 442 612 300) (9 442 612 301) (9 680 610 095)
Set screw Spacer Measuring device

25. 157847-0820 26. 157915-9820 27. 157915-9201

(9 442 612 370) (9 681 610 687) (9 681 610 684)
Coupling Holder Bit

-7-
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 11/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 12/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 13/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 14/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

SPECIAL TOOLS

1. 105796-0000 2. 157808-4720 3. 157641-6820

(1 688 010 129) (9 442 612 278) (9 443 612 974)
Fixing stand Injection pipe Joint assembly

4. 157811-9020 5. 157829-0820 6. 157971-1020

(9 681 610 453) (9 681 610 336) (9 443 613 442)
Flange Adjusting device Piping assembly

200
M12X1.5

11

M10X1.0

7. 105781-0890 8. 105793-0020 9 . 157845-9520

(9 680 610 087) (9 681 610 418) (9 681 610 630)
Stand Adjusting device Pipe assembly

- 11 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 15/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

SPECIAL TOOLS

[3] Adjustment controller assembly breakdown:

Key no. 1: 105782-8360 (9 680 610 209)
Note:
The numbers in brackets below are Bosch part numbers.

1:105782-8360 1-1: 157966-4020

(9 443 613 446) 1-1-1: 157966-4120 (9 443 613 447)
(9 680 610 209) 1-1-2: 157966-4420 (9 443 613 448)
1-1-3: 157966-4520 (9 443 613 449)
1-1-4: 157966-4620 (9 443 613 450)
1-1-5: 157966-4720 (9 443 613 451)
1-1-6: 157966-4820 (9 443 613 452)
1-1-7: 157966-4920 (9 443 613 453)
1-1-8: 157966-5020 (9 443 613 454)
1-1-9: 157966-5100 (9 443 613 455)
1-2: 157966-3720
(9 443 613 456)

1-3: 157966-3820
(9 443 613 457)
1-4: 157966-3920
(9 443 613 458)

Note:
Key number 1 (RBAJ part no.105782-8360, Bosch part no. 9 680 610 209) enables adjustment of
both VRZ and COVEC-F pumps.
With the VRZ, however, only key numbers 1-1 (RBAJ part no. 157966-4020, Bosch part no. 9 443
613 446) and 1-3 (RBAJ part no. 157966-3820, Bosch part no. 9 443 613 457) are necessary.

Adjustment controller assembly part table (for VRZ)

Key Qty
RBAJ part no Bosch part no Part name Remarks
no

1-1 157966-4020 9 443 613 446 CONTROLLER ASSY 1

1-1-1 157966-4120 9 443 613 447 Controller unit 1 Checker assy

1-1-2 157966-4420 9 443 613 448 Wire harness 1 Power supply (Japan, USA)

1-1-3 157966-4520 9 443 613 449 Wire harness 1 Power supply (EC)

1-1-4 157966-4620 9 443 613 450 Wire harness 1 P C: COM1 ~ MC-02

1-1-5 157966-4720 9 443 613 451 Wire harness 1 P C: COM2 ~ MC-02

1-1-6 157966-4820 9 443 613 452 Wire harness 1 FCV GND harness

1-1-7 157966-4920 9 443 613 453 Main harness 1 Controller-Pump GE

1-1-8 157966-5020 9 443 613 454 Main harness 1 Controller-Pump ROM

1-1-9 157966-5100 9 443 613 455 CD-ROM 1 Software (Overseas Ver.) & (Calibration data)
& Manual

1-3 157966-3820 9 443 613 457 ECU assembly 1 For Mitsubishi 4M41 engines

- 12 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 16/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

SPECIAL TOOLS

1-1 157966-4020
(9 443 613 446)
CONTROLLER ASSY

1-1-1 157966-4120 1-1-2 157966-4420 1-1-3 157966-4520

(9 443 613 447) (9 443 613 448) (9 443 613 449)
Controller unit Wire harness Wire harness

1-1-4 157966-4620 1-1-5 157966-4720 1-1-6 157966-4820

(9 443 613 450) (9 443 613 451) (9 443 613 452)
Wire harness Wire harness Wire harness

2000
2000

1000

1-1-7 157966-4920 1-1-8 157966-5020 1-1-9 157966-5100

(9 443 613 453) (9 443 613 454) (9 443 613 455)
Main harness Main harness CD-ROM

2000
2990

- 13 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 17/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 18/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

DISASSEMBLY

1. PREPARATION
 Clean the outside of the injection pump • Lay out the disassembled parts neatly and
before disassembly, removing all grease and sequentially on the work bench, labelling
dirt. Drain the fuel oil from the pump. them if necessary, to facilitate later
• Keep the work bench and workshop clean reassembly.
and tidy. • Prepare a container of clean fuel oil for
• Before beginning disassembly, record plungers, delivery valves and other precision
performance data for later reference to parts.
facilitate the diagnosis of malfunctions and
defects, if any, in the pump.

2. EXPLODED VIEW

153
150
65
161 150/8
152 956
151
121 66
120 955
37
35
36
948 949 34
33 160
110 38 100 122
111 50 22 101
130
112 878S

50 102
949 32
31
55 911 910
30
56 46 35
45
905
50 11 912
50 17 914 3
51 2

50 205 1 922
53 5
54 60 41
62 6 40
61 16 7 80/7 42
8 43
10
9
25 83
18
20

15 80/8 82
931 930
80
920

26
27 810S 856S 925 923

P-VRZR- 326

- 15 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 19/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

DISASSEMBLY

Injection pump body 3. ENGINE DRIVE GEAR REMOVAL

(1) Fix the injection pump bracket in a vise.

P-VRZR- 300

Bolt (M6x1)
(2) Install wrench B so that it can turn the two
gears (ie, the main gear and the sub-gear)
clockwise.
(3) Turn the main gear and the sub-gear using
wrench A until they are aligned. Then, insert
a bolt through the two gears and tighten it
using a torque wrench. (Tighten
Wrench A temporarily.)
Drive gear
Tool name Part no Remarks
Wrench A 157917-4920
Wrench B P-VRZR- 301 Wrench B 157917-4620

Note:
The drive gear is divided into the main gear and
the sub-gear.
Wrench B is used to prevent drive gear rotation.
Wrench A is used to align the main gear and
the sub-gear.

Bolt (M6x1) (4) Remove wrenches A and B and the torque

wrench from the drive gear.
(5) Install wrench B so that the main gear and
the sub-gear are in the center of wrench B.
(6) Remove the bolt from the drive gear.
(7) Align the main gear and the sub-gear using
wrench A, then install the bolt and tighten
Wrench A to the specified torque.
Drive gear Specified torque: 9 ~ 13 Nm
{0.9 ~ 1.3 kgf•m}
Wrench B P-VRZR- 318

- 16 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 20/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

DISASSEMBLY

(8) Remove wrench A.

Sub-gear
P-VRZR- 302

(9) Remove the roundnut (SW21) fixing the

drive gear.
Socket wrench

P-VRZR- 303

(10) Assemble puller A in the gap between the

Bolt drive gear and the bracket and loosely fix
the bolts.
Tool name Part no Remarks
Puller 157927-4500 Parts A and B
Puller A

P-VRZR- 304

Drive shaft
(11) Assemble puller B to the drive shaft and
puller A.
Puller B

P-VRZR- 305

- 17 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 21/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

DISASSEMBLY

Drive gear (12) Tighten the puller bolt to remove the drive
gear.
Advice
Hold the puller so that it does not drop when
the gear is removed from the drive shaft.

Bolt

P-VRZR- 306

(13) Remove the drive shaft key.

Key

Drive shaft
P-VRZR- 307

Bracket (14) Remove the nuts (at three locations).

(15) Remove the bracket from the pump
housing and then remove the O-ring.

Nuts (3)

O-ring

P-VRZR- 319

- 18 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 22/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 23/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

DISASSEMBLY

Grommet Nut [2] Magnet valve removal

Magnet valve
(1) Remove the magnet valve harness grommet
and then remove the harness nut.
(2) Remove the magnet valve and the filter.
Advice
Do not lose the armature spring.

P-VRZR- 020

Holder GE cover [3] GE actuator removal

GE actuator Torx bolts (6)
(1) Remove the GE actuator’s torx bolts and
Spring washers (6) spring washers.
Tool name Part no Remarks
Bit
Holder 157915-9820
Bit 157915-9600 T30

Advice
Do not remove the GE cover.

P-VRZR- 021

(2) Remove the GE actuator.

Advice
Do not damage the ball pin (refer to the GE
GE actuator
actuator on page 35).

P-VRZR- 022

[4] Regulating valve removal

Socket
Assemble the socket wrench to the
Regulating valve
wrench regulating valve and then remove the
regulating valve.
Tool name Part no Remarks
Socket wrench 157913-7000

P-VRZR- 023

- 20 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 24/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 25/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

DISASSEMBLY

(2) Remove the TPS bolts.

TPS bolts (2)

TPS

P-VRZR- 026

Timer spring (3) Remove the TPS, the adjusting shim, the
Adjusting shim
timer spring, the core rod and the TPS
TPS
standard point shim.
Advice
Label the TPS standard point shim and the
timer stroke adjusting shim to avoid
mistaking them at reassembly.

TPS standard point shim Core rod P-VRZR- 027

Torx bolts (2) (4) Remove the timer cover and the O-rings
O-ring (large) (large and small).
Tool name Part no Remarks
Holder 157915-9820
Bit 157915-9600 T30

Timer cover

O-ring (small)
Bit Holder P-VRZR- 028

- 22 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 26/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

DISASSEMBLY

[7] CPV (constant pressure valve)

holder and plug removal
(1) Loosen the CPV holders.
Socket wrench Tool name Part no Remarks

Socket wrench 157914-3600

CPV holders (4)

P-VRZR- 029

(2) Remove the CPV holders and the gaskets.

Gaskets (4) Advice
Distributor head Line up the removed CPV holders in order
CPV holders (4) to match the positions (A, B, C, D) on the
distributor head from where they were
removed.

P-VRZR- 030

(3) Remove the plug using a hexagon wrench

(SW14mm).
Hexagon wrench

Plug

P-VRZR- 031

(4) Remove the snapring and shim from the

Snapring rotor shaft.
Distributor head
Shim Note:
The shim is easier to remove after removing the
distributor head assembly.

P-VRZR- 032

- 23 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 27/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 28/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

DISASSEMBLY

Rollers (2) Remove the rotor shaft assembly and

Rotor shaft assembly
remove the rollers and roller shoes from the
Clip rotor shaft.
Roller shoes
Advice
Spring
• Do not drop the rollers or the roller shoes.
• Do not change the roller and roller shoe
combinations.
(3) Assemble the clip to prevent the plunger
from dropping out of the rotor shaft
assembly.
P-VRZR- 036
Tool name Part no Remarks
Clip 157971-0500

Advice
Do not disassemble the plunger from the
rotor shaft.

[10] Snapring removal

Insert the hook’s pin into the snapring’s hole
Hook
and tighten the butterfly nut to pull out the
Pin
snapring.
Snapring
Tool name Part no Remarks
Hook 157928-5820

P-VRZR- 037

[11] Drive shaft removal

Remove the drive shaft, the washer and the
Drive shaft
seal ring.

Seal ring
Washer
P-VRZR- 038

- 25 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 29/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 30/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 31/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 32/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 33/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 34/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 35/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

COMPONENT INSPECTION

(6) Replace the drive shaft assembly if there is

any play between the rotor shaft’s ball pin
and the drive shaft.

Ball pin

Drive shaft assembly

Rotor shaft P-VRZR- 056

[7] Rotor shaft assembly

Rotor shaft assembly
(1) Replace the distributor head assembly if any
of the rotor shaft assembly’s sliding parts
are peeling, gnawed or scorched.
Radial plungers
(2) Replace the washer with a new one if it is
worn.

Roller shoes

Washer
Rollers P-VRZR- 057

[8] Cam ring

(1) Replace the cam ring if the cam ring pin is
Cam ring worn.
(2) Replace the cam ring if there is any play
between the cam ring pin and the timer
slider.
Pin

Timer slider

P-VRZR- 058

(3) Replace the cam ring if the cam ring’s cam

profile is peeling or scorched.
Cam ring

P-VRZR- 059

- 32 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 36/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 37/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

COMPONENT INSPECTION

(5) Assemble the GE actuator’s ball pin to the

control sleeve groove. If there is any play,
GE actuator’s ball pin
replace the distributor head assembly.

Control sleeve

P-VRZR- 064

[11] CPV (constant pressure valve)

holder
Replace the CPV holder if the CPV holder
seat is scratched.

CPV holder

P-VRZR- 065

[12] Plug and rotor shaft spring

(1) Replace the rotor shaft spring if it is rusted
or damaged.
(2) Replace the plug with a new one if it is burred
or the thread is damaged.
Advice
Always replace the O-ring assembled to the
plug with a new one.
Plug Rotor shaft spring

P-VRZR- 066

[13] Regulating valve

Replace the regulating valve assembly if the
Regulating valve
piston inside the regulating valve is sticking.
Advice
• Always replace the O-rings with new
ones.
O-rings • Do not disassemble the regulating valve
unless necessary.
Stopper

P-VRZR- 067

- 34 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 38/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

COMPONENT INSPECTION

[14] Magnet valve

Magnet valve
(1) Replace the magnet valve assembly if the
armature is scorched or cracked.
(2) Replace the magnet valve assembly if the
spring is damaged or rusted.
O-ring Advice
Spring
Always replace the O-ring with a new one.
(3) Check the magnet valve resistance and
Armature replace the magnet valve assembly if the
resistance is not as specified.
Gauze filter
P-VRZR- 068 Terminal Resistance Ambient temperature
nos (Ω ) (°C)
1 - GND 8.0±1.2 23±5
GE actuator
Ball pin (4) Clean the gauze filter.

[15] GE actuator
(1) Replace the GE actuator if the ball pin is
worn or if the plating is damaged or peeling.

P-VRZR- 069

(2) Assemble the GE actuator’s ball pin in the

GE actuator control sleeve groove and confirm that there
is no play.
If there is any play between the ball pin and
the control sleeve, replace the GE actuator
or the distributor head assembly or both.

Control sleeve

GE actuator terminals (reference)

P-VRZR- 070
Terminal no. Name Remarks
1 FCV Black, magnet valve
2 Blank -
3 Blank -
12
6 4 CSP (OSC) Yellow
11
5 5 TCV (+) Red
10
4 6 GE (+) White
3 7 TF (+) Blue, fuel temperature (+)
2
9 8 CSP (MDL) Red
8 9 TCV (-) Black
1
7 10 GE (-) Green
11 TF (-) Grey, fuel temperature (-)
P-VRZR- 312 12 CSP (GND) Black

- 35 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 39/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 40/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

COMPONENT INSPECTION

[18] Np sensors
Np sensors
1 Measure the Np sensors’ resistances.
Terminal nos Resistance (Ω ) Remarks
(-)
2-3 2.15k Main
2 (-)

3 (+)
2-3 2.15k Backup
(+)
Advice
W h e n u s in g a d ig ita l c ir c u it te s te r ,
resistances cannot be measured unless you
hold the minus probe against the No. 2
terminal and the plus probe against the No.
P-VRZR- 314 3 terminal.

(kΩ) [19] Fuel temperature sensor

Measure fuel temperature sensor
resistances.
See page 35 for GE actuator terminals.
  e
  c
  n
  a
Reference values:
   t
  s
   i
  s (25, 2) = (fuel temperature, resistance) Terminal Resistance
  e Fuel temperature (°C)
   R nos ( Ω)
7-8 2 25

Fuel temperature (°C) P-VRZR- 163

- 37 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 41/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 42/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 43/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

GEAR REASSEMBLY

Sub-gear (7) Attach the sub-gear to the main gear. At

this time, hook the sub-gear’s pin to the
spring.
Spring

Pin

P-VRZR- 333

Wrench (8) Align the wrench with the sub-gear’s holes

and attach it to the sub-gear.

Sub-gear Tool name Part no Remarks

Wrench 157917-4920

P-VRZR- 334

Socket head bolt (9) Turn the wrench counterclockwise to align

Wrench the main gear’s teeth with the sub-gear’s
teeth.
Sub-gear
(10) Screw in the socket head bolt (SW5) to
tighten the sub-gear to the main gear.
Specified torque: 9 ~ 13 N·m
{0.9 ~ 1.3 kgf·m}
Part no
Part name Remarks
(Mitsubishi part no)
149917-1500
Socket head bolt SW5
(ME204287)
P-VRZR- 335

CAUTION
Pliers
Snapring Socket head bolts cannot be reused.
Main gear

(11) Hold the snapring open using pliers and

install it in the main gear’s snapring groove.
Tool name Part no Remarks
Pliers 157928-4400

Part no
Part name Remarks
(Mitsubishi part no)

Base Snapring 149931-1600

P-VRZR- 336 (ME204236)

- 40 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 44/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 45/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

The reassembly of the VRZ type injection pump

Liner is basically the reverse of the disassembly
procedure. The following describes the standard
Blade Stamping
reassembly procedure.
Always replace gaskets and O-rings with new
ones.
1. REASSEMBLY
[1] Feed pump assembly reassembly
Advice
Rotor  Confirm that the blades’ grooves are
P-VRZR- 077
positioned toward the inside.
• Blade and rotor orientation cannot be
changed.
• The feed pump’s liner is marked with an
‘R’ for clockwise injection pump rotation
or an ‘L’ for counterclockwise injection
pump rotation. Install the liner so that
the applicable mark can be seen when
the liner is viewed from the head side.

Pins
Cover
(1) Position the feed pump assembly and the
cover on the feed pump holder. Assemble
the holder pins in the feed pump holes (2).
Tool name Part no Remarks
Notch Feed pump holder 157928-4320
Chamfer
Advice
Align the feed pump cover notch with the
Feed pump holder
feed pump holder chamfer.
Notch Feed pump

P-VRZR- 078

(2) Position the feed pump cover notch toward

the GE actuator side and insert the feed
pump assembly into the pump housing until
Notch
the feed pump is contacting the housing.
(3) Hold the feed pump holder so that it does
not move and turn the pump housing upside
Pump housing down.

Feed pump holder

P-VRZR- 079

- 42 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 46/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 47/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

(10) Remove the set screw and install the other

Holder two torx bolts.
(11) Tighten the four torx bolts uniformly. (One
Bit
of the four torx bolts does not screw into
the pump housing.)
Specified torque: 3.0 ~ 4.0 N·m
{0.3 ~ 0.4 kgf·m}
For feed pump Part no Remarks
149916-0400
Short torx bolt 1
(9 443 612 874)
P-VRZR- 083 149916-0300
Long torx bolt 3
(9 443 612 873)

Tool name Part no Remarks

Holder 157915-9820
Bit 157915-9201 T15

Advice
Move the rotor backward and forward and
left and right with your finger and check that
it moves smoothly. If it does not move
smoothly, loosen the feed pump cover and
then retighten it to the specified torque.

(12) Insert the seal ring into the feed pump

cover.
Seal ring Advice
Be careful with the assembly orientation of
the seal ring and ensure it is securely
assembled to the feed pump cover.

Feed pump Head

side side

P-VRZR- 084

[2] Bearing reassembly

Button
Holder (1) Assemble the holder to the bearing and
press the holder button (to hold the bearing).
Bearing
(2) Install the bearing in the pump housing.
Pump housing Tool name Part no Remarks
Holder 157928-3620

Advice
Ensure the bearing is positioned correctly.

P-VRZR- 085

- 44 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 48/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

[3] Timer piston reassembly

(1) Assemble the slider in the timer piston.

Timer piston

Slider

P-VRZR- 086

Timer’s low pressure side (2) Assemble the timer piston and slider in the
Pump housing
Slider hole
pump housing.
Advice
• Align the slider hole with the timer piston
hole.
Timer piston
• The slider is assembled in the timer with
the hole positioned toward the GE
actuator side.
Note:
The timer piston’s low pressure side is
positioned toward where the Q adjustment ROM
Timer’s low pressure side P-VRZR- 087
is installed.
Cam ring [4] Cam ring reassembly
Assemble the cam ring in the pump housing.
At this time, insert the cam ring pin into the
timer piston’s slider hole.
Cam ring pin
Advice
Confirm that the timer piston slides
smoothly.

Pump housing P-VRZR- 088

- 45 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 49/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

[5] Drive shaft reassembly

(1) Insert the holder into the bearing.
(2) Press the holder button to hold the bearing
and pull the bearing into the head.
Advice
Pull the bearing into the head so that a gap
remains between the feed pump cover and
the bearing.
Tool name Part no Remarks
Holder 157928-3620
Holder
P-VRZR- 089

Spacer Feed pump cover (3) Insert the spacer into the pump housing.
Spacer
Tool name Part no Remarks

U-shaped Spacer 157928-4700

ring

Bearing

Pump housing P-VRZR- 090

(4) Assemble the shim and the feed pump’s

Shim drive side key on the drive shaft.
Key (5) Assemble the oil seal guide on the drive
shaft thread.
Tool name Part no Remarks
For φ 25 dia
Oil seal guide 157928-4000
shaft

Drive shaft Oil seal guide

P-VRZR- 091

(6) Confirm that the seal ring is inserted into

the feed pump cover (see bottom figure of
page 44).
Drive shaft (7) Align the drive shaft key with the feed pump
rotor key groove and insert the drive shaft
into the feed pump.
Advice
Insert the drive shaft gently into the feed
pump while turning it clockwise and counter
clockwise to align the key with the key
groove.
P-VRZR- 092

- 46 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 50/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Plastic hammer (8) Lightly tap the drive shaft using a plastic
Drive shaft hammer to assemble the drive shaft with the
end fully protruding from the drive side.
1 ~ 2 mm Advice
;
• When tapping the drive shaft with the
plastic hammer, ensure no burrs or dirt
remain on the shaft.
;
Inner cam • Insert the drive shaft so that the end of
the drive shaft is 1 ~ 2 mm higher than
the end of the inner cam (when viewed
from above).
P-VRZR- 093
• After assembling the drive shaft, confirm
that the shaft rotates smoothly.

Spacer
[6] Snapring reassembly
(1) Remove the spacer from the pump housing.
Pump housing Advice
Confirm that the drive shaft’s snapring
groove can be seen through the housing
window.

P-VRZR- 094

(2) Assemble the snapring to the clip.

Tool name Part no Remarks
Clip 157928-3120

Clip Advice
Snapring Position the snapring on the clip with the
convex face toward the clip.

Convex face

P-VRZR- 095

(3) Position the snapring in the drive shaft’s ring

groove and push it straight down.
Clip
(4) Remove the clip from the snapring and use
Drive shaft’s snapring groove the end of the clip to push the snapring fully
Snapring
into the groove.
Advice
Confirm that the snapring is fully inserted
into the groove and that the drive shaft can
be rotated.

P-VRZR- 096

- 47 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 51/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Distributor head
[7] Adjusting drive shaft axial play
(1) Position the distributor head on the pump
housing.
Advice
Pump housing Do not assemble the O-ring or the control
sleeve at this time.

P-VRZR- 097

(2) Install and tighten two diametrically opposed

torx bolts of the four to install the distributor
Holder head.
Specified torque: 10.0 ~ 14.0 N·m
Bit {1.0 ~ 1.4 kgf·m}
Torx bolts (2) Tool name Part no Remarks
Holder 157915-9820
Bit 157915-9600 T30

P-VRZR- 098

(3) Attach the measuring device to the drive

Measuring device shaft.
Dial gauge (4) Attach the dial gauge to the measuring
device.
Tool name Part no Remarks
Measuring device 105782-4530

Drive shaft P-VRZR- 099

Measuring device (5) Measure the drive shaft’s axial play.

Specified value: 0.1±0.05 mm
(with the head assembly installed)
(6) If not as specified, select shims from the
table on the following page and exchange
the shims until the axial play is as specified.
(Refer to page 49.)
Advice
If the axial play varies greatly from the
specified value, repeat procedure [5] on page
Drive shaft P-VRZR- 100 46 and [6] on page 47.

- 48 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 52/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Shims
RBAJ part no Bosch part no Thickness (mm)
149602-0000 9 443 612 809 1.90
149602-0100 9 443 612 810 1.95
149602-0200 9 443 612 811 2.00
149602-0300 9 443 612 812 2.05
149602-0400 9 443 612 813 2.10
149602-0500 9 443 612 814 2.15
149602-0600 9 443 612 815 2.20
149602-0700 9 443 612 816 2.25
149602-0800 9 443 612 817 2.30
149602-0900 9 443 612 818 2.35
149602-1000 9 443 612 819 2.40

(7) Remove the dial gauge.

Measuring device (8) Remove the measuring device handle and
attach the extractor.
(9) Screw in the extractor to remove the
measuring device.
Tool name Part no Remarks
Extractor 157926-2421

Extractor
P-VRZR- 101

(10) Remove the torx bolts from the distributor

Distributor head head.
(11) Remove the distributor head from the
pump housing.

Pump housing

P-VRZR- 102

Rotor shaft
[8] Selecting the rotor shaft shim
Distributor head Purpose
The rotor shaft’s axial play is measured and then
the play is adjusted to the specified value using
the shim.

Procedure 1 Adjusting the dial gauge’s ‘0’

point
(1) Insert the rotor shaft into the distributor head.

Snapring (2) Install

snapringthe snapring in the rotor shaft’s
groove.
P-VRZR- 103
Advice
Do not assemble the shim at this time.

- 49 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 53/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

(3) Attach the adapter to the head and then

Head attach the measuring device to the adapter.
Tool name Part no Remarks
Measuring device
Adapter 157845-8900
Measuring 157829-3520 For measuring
device VE cam lift

Rotor shaft Adapter

P-VRZR- 104

(4) Pull the rotor shaft fully to the left and set
Head
the dial gauge to the ‘0’ position.

Measuring device

Rotor shaft
Dial gauge
Adapter

P-VRZR- 105

Procedure 2 Calculat ing the shim

Head thickness
(1) Push the rotor shaft fully to the right and
Measuring device
measure the full stroke from the dial gauge.
Advice
The rotor shaft’s groove must not catch on
the head.

Rotor shaft Adapter

P-VRZR- 106

Rotor shaft
(2) Select a shim using the formula below.
Distributor head Shim thickness = full stroke – 0.2 (mm)
RBAJ part no Thickness
Bosch part no
(key no. 53) (mm)
149720-0000 9 443 612 851 2.1
149720-0100 9 443 612 852 2.2
149720-0200 9 443 612 853 2.3
149720-0300 9 443 612 854 2.4
(3) Install the selected shim and the snapring
Shim Snapring to the inserting
(4) After rotor shaft.
the shim, confirm that the
P-VRZR- 107
stroke is as specified. If not as specified,
repeat Procedure 1 and Procedure 2.
Specified stroke: 0.2±0.1 mm
- 50 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 54/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

(5) Remove the dial gauge and adapter from

the head.
(6) Remove the snapring.

TPS standard point shim [9] TPS and timer cover reassembly
Pump housing
Adjusting shim (1) Assemble the TPS to the pump housing.
Specified torque: 7.0 ~ 10.0 N·m
Core rod {0.7 ~ 1.0 kgf·m}
Advice
Do not mistake the positions of the TPS
standard point shim and the adjusting shim.
TPS

P-VRZR- 108

(2) Assemble the O-rings (at two locations) and

Timer cover
Pump housing then assemble the high pressure side timer
cover on the pump housing.
Specified torque: 7.0 ~ 10.0 N·m
{0.7 ~ 1.0 kgf·m}

P-VRZR- 109

[10] Pump removal

Remove the pump housing from bracket C.

Pump housing

Bracket C
P-VRZR- 110

- 51 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 55/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

2. PRE-STROKE ADJUSTMENT

Cam ring Link plate

Pre-stroke adjustment values

   )
  m
  m
   (
   t
   f
   i
   l
 
  m
Timing link shaft ball pin   a
   C

Control sleeve   e

   k
  o
  r
   t
  s
  -
  e
  r
  p
   l
  a
  n
   i
  g
   i
  r
   O Angle of cam rotation (°)

Beginning of Beginning of pressure

Cam link pin cam lift delivery

VRZ pre-stroke (substitute)

Timer piston Timing link shaft
P-VRZC- 034 P-VRZR- 315

Fundamentally, pre-stroke is the amount of lift from the cam’s bottom dead center position to the
beginning of pressure delivery position. With the VRZ pump, however, because it is not possible
to measure the cam lift with the pump assembled, the cam angle is instead measured from the
beginning of cam lift position to the beginning of pressure delivery position.
The beginning of pressure delivery position can be changed by changing the phase (ie, the angle)
between the cam link and the control sleeve, which are connected by the timing link shaft.
Consequently, by changing the position of the link plate groove, we can change the phase of the
cam link and the control sleeve to adjust the pre-stroke (ie, substituting the angle instead).

Pre-stroke adjustment sequence

(1) Attach the measuring device to the pump.
(2) Align the measuring device’s measuring terminal with the standard cylinder B’s cam position.
(3) Find the cam’s bottom dead center position using the dial gauge, then zero the dial gauge.
(4) Rotate the pump in the specified direction of rotation and set the cam lift to 0.70 mm using the
dial gauge.
(5) Set the ‘0’ point using the KMA device to display cam lift as an angle.
(6) Turn the pump back 10° in the direction opposite to the specified direction of rotation. Turn the
pump 5° in the specified direction of rotation (to prevent backlash).
(7) Confirm that the dial gauge displays 0 mm.
(8) Using the KMA device, reset the ‘0’ point. (Using the KMA device, begin cam lift.)

- 52 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 56/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Injection pump Flange [1] Measuring device installation

CAUTION
The pump test bench drive motor must be
turned OFF.
Injury or damage may result if the pump test
bench drive motor is turned ON.
(1) Temporarily attach the fixing stand to the
pump test bench and attach the injection
pump to the fixing stand.
Fixing stand P-VRZR- 316 Tool name Part no Remarks
Fixing stand 105796-0000 For 20NP
Flange 157811-9020 For VRZ

(2) Align the

cylinder B’skey groove
pressure with the
delivery camstandard
position
as shown at left.

Drive shaft key position

for 4M41 model engine

P-VRZR- 111

(3) Align the drive shaft key groove and the

Measuring terminal
measuring device’s measuring terminal.
Note:
• The pre-stroke can be measured on any
cylinder. Because the pump is set at the
Drive shaft key groove standard cylinder B, however, measure the
pre-stroke for this cylinder.
• If the driv e s ha ft ke y g ro ov e a nd th e
measuring device’s measuring terminal are
not aligned, pre-stroke cannot be adjusted
Measuring device from cylinder B when the rotor shaft is
P-VRZR- 317

assembled.
Measuring device Existing bolts (2) Drive shaft (4) Install the pre-stroke measuring device.
Specified torque: 10.0 ~ 14.0 N·m
{1.0 ~ 1.4 kgf·m}
Tool name Part no Remarks
Measuring device 105782-4540

Advice
Assembly position • Align the drive shaft’s key groove and the
of measuring
device’s measuring
measuring device’s measuring terminal
terminal with the drive shaft.
P-VRZR- 112 • Ensure the end of the measuring device
is securely assembled to the drive shaft
groove.

- 53 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 57/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

(5) Assemble the key to the drive shaft. Align

Coupling
the coupling with the key, assemble it to the
Fixing stand
drive shaft and then fix it using the nut.
Tool name Part no Remarks

Coupling 157847-0820 Shaft dia φ 25

Specified torque: 167 ~ 185 N·m
{17.0 ~ 19.0 kgf·m}

P-VRZR- 114

(6) Move the fixing stand to assemble the

Test bench drive coupling
coupling teeth to the pump test bench drive
coupling.
Advice
Ensure approximately 1 mm axial clearance
between the coupling and the drive coupling.

Fixing stand

P-VRZR- 115

Flywheel
(7) Securely tighten the fixing stand installation
bolts and nuts and the drive coupling socket
head bolt to fix the injection pump to the
pump test bench.
(8) Turn the pump test bench flywheel using the
lever to confirm that the injection pump
rotates smoothly.
CAUTION
Remove the lever after operating the
Lever flywheel.
P-VRZR- 116 Operating the test bench without removing
the lever can cause serious injury and
damage the test bench.

- 54 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 58/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Monitor display example [2] Setting the ‘0’ point for pre-stroke
1 2 3 4 5
angle measurement
6 7 8 9 10 11 12
adjustment
(1) Turn the pump test bench’s main switch ON
and set the KMA (continuous measuring
device) as described below. [Refer to the
KMA (continuous measuring device
operation manual): Publication No EC18E-
11091.]

Select the ‘angle measurement display’ 

Press F6  Select ‘Settings’ 
Press ‘Enter’  Set the direction of rotation
F1 F2 F3 F4 F5 F6 F7 F8  Press F2 F2 

P-VRZR- 164

Flywheel (2) Turn the pump test bench flywheel in the

direction of pump rotation to find the
standard cylinder’s bottom dead center
position on the measuring device dial gauge.
(Refer to the data sheet for the standard
cylinder.)

Dial gauge P-VRZR- 118

(3) Zero the dial gauge.

(4) Turn the flywheel in the direction of rotation
so that the dial gauge reading is 0.7 mm.

Dial gauge

P-VRZR- 117

- 55 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 59/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Monitor display example (5) Set the continuous measuring device as

a n g l e m e a s u r e m e n t  
described below.
1  5 3  6 2 4  

Press F2  Press both shift keys (press both

0 . 0 
shift keys at the same time to activate angle
control)  the monitor will display the dialog
‘position control unit error: control circuit
open’)  Press Enter  the monitor display
will change to(---.-°)  Press F6  Select
‘zero point setting’   Press Enter. (The
pump test bench angle measurement is now
set at ‘0.’)
(6) To absorb backlash, turn the flywheel back
at leas t 10° and then s et the an gle
F 1 F 2 F 3 F 4 F 5 F 6 F 7 F 8  
measurement display at 355° (ie, turn the
P-VRZR- 165
flywheel back 5°).
(7)
(8) Check
Set thethat the dial gauge
continuous reading
measuring is 0mm.
device as
Flywheel
described below.
Press F6  Select ‘zero point setting’  
Press Enter.
(The pump test bench angle measurement
is now set at ‘0.’)
Advice
Do not alter the continuous measuring
device angle measurement menu after this.
Note:
The beginning of cam lift position is now set.
P-VRZR- 119

(9) Remove the measuring device.

Measuring device

P-VRZR- 120

- 56 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 60/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Pump housing (10) Remove the TPS from the pump housing.
(11) Remove the timer cover from the pump
housing.

TPS

Timer cover

P-VRZR- 121

[3] Component reassembly

(1) Rotor shaft reassembly
(1) Select a forked plate as described below and
then assemble the plate.
Selecting a forked plate
Head assembly Cam ring Forked plate marked G

Forked plate Replaced Replaced Replaced

Not
Replaced Replaced
replaced
Holder Bit
Not replaced Replaced Replaced
P-VRZR- 122
Not Do not replace (use the
Not replaced
Drive shaft
replaced installed forked plate)*
Rotor shaft pin
Spring *If the installed forked plate fork is worn,
assemble a forked plate marked ‘G.’
(Refer to the table on page 67.)
Specified torque: 3.0 ~ 5.0 N·m
{0.3 ~ 0.5 kgf·m}
Clip Tool name Part no Remarks
Rotor shaft
Holder 157915-9820
Rotor shaft assembly Bit 157915-9301 T20

P-VRZR- 123
(2) Rotate the drive shaft so that the rotor shaft
pin is positioned toward the GE actuator as
shown at left.
Note:
The rotor shaft does not contact the forked pate.
(3) Remove the clip from the rotor shaft.
Tool name Part no Remarks
Clip 157971-0500
(4) Assemble the radial plungers, the roller
shoes and the rollers to the rotor shaft.
(5) With the spring assembled to the rotor shaft,
assemble the rotor shaft assembly to the
drive shaft groove.
Advice
Do not drop the roller shoes or the rollers.

- 57 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 61/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

(2) Distributor head assembly reassembly

Control sleeve (1) Assemble the O-ring on the distributor head.
(2) Assemble the control sleeve in the
distributor head.
Head side
Advice
The face with the larger chamfer is
Large chamfer Small chamfer positioned toward the head.

Distributor head

P-VRZR- 124

O-rings (2) (3) Assemble the distributor head assembly to

Distributor head the rotor shaft.
(4) Tighten diagonally opposed torx bolts to
loosely install the distributor head.
Advice
Do not tighten the distributor head assembly.
Leave it loose.
(5) Assemble the distributor head assembly to
the pump housing.
Advice
Move the timer piston to align the forked
Pump housing P-VRZR- 125
plate groove with the distributor head
assembly pin.
Torx bolts (6) control
Move the timerrotates,
sleeve piston and
andconfirm that the
then gradually
tighten two diametrically opposed torx bolts.
(7) If the timer piston does not move smoothly,
loosen the torx bolts and repeat procedure
(6) above.
Note:
If the timer piston does not move smoothly, the
Distributor head control sleeve will not move smoothly, the pin
may not engage the plate when the head is
tightened, and either the plate or the pin may
P-VRZR- 126
Pump housing be damaged.
(8) Tighten the torx bolts until the distributor
head assembly is securely tightened to the
pump housing.

- 58 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 62/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

(9) Install the other two torx bolts and then

tighten all four torx bolts to the specified
torque.
Specified torque: 10.0 ~ 14.0 N·m
Torx bolts (4) {1.0 ~ 1.4 kgf·m}
Tool name Part no Remarks
Holder
Holder 157915-9820

Bit Bit 157915-9600 T30

P-VRZR- 127

(10) Assemble the shim and snapring to the

rotor shaft.
(11) Install the plug to the distributor head
O-ring
Snapring together with a new O-ring.

Shim
Plug
P-VRZR- 128

(12) Tighten the plug using a hexagon wrench

(SW14mm).
Plug Specified torque: 20.0 ~ 29.0 N·m
Hexagon wrench {2.0 ~ 3.0 kgf·m}

P-VRZR- 129

(3) CPV holder reassembly

(1) Assemble the gaskets and CPV holders to
Dummy holder the distributor head’s cylinders A, C and D.
Cylinder B Advice
The CPV holders must be reassembled to
the distributor head in their original positions
A, C and D marked on the head.
(2) Assemble the dummy holder and gasket to
Gaskets (4)
the distributor head’s cylinder B.
CPV holders (3)

Tool name Part no Remarks

Distributor head P-VRZR- 130 Part of pipe assembly
Holder 157845-9500
157845-9520.

- 59 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 63/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 64/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

(5) Timer cover and TPS (timer piston

sensor) reassembly
(1) Assemble the timer cover and the small and
large O-rings (new) to the high pressure side.
(See below for the assembly procedure.)

Small O-ring Timer

cover
Large O-ring P-VRZR- 135

Small O-ring Pump housing (2) Push the small O-ring securely into the pump
Large O-ring housing using your finger.
(3) Push the large O-ring securely into the timer
cover using your finger and install the timer
cover using the torx bolts.
Specified torque: 7.0 ~ 10.0 N·m
Timer
{0.7 ~ 1.0 kgf·m}
Torx bolts (2) cover
Tool name Part no Remarks
Bit
Holder 157915-9820
Holder
Bit 157915-9600 T30
P-VRZR- 136

TPS O-ring (4) Assemble the TPS standard point shim, the
core rod, the timer spring and the timer
Timer stroke
stroke adjusting shim in the pump housing.
adjusting shim Advice
Do not mistake the assembly positions of the
TPS standard point shim and the timer stroke
adjusting shim.
(5) Assemble the TPS to the pump housing.
Timer spring Advice
Core rod Ensure the O-rings are not damaged.
Standard point shim
Pump housing P-VRZR- 137

(6) Secure the TPS to the pump housing using

Pump housing the torx bolts and a socket wrench (M6).
TPS
Specified torque: 7.0 ~ 10.0 N·m
{0.7 ~ 1.0 kgf·m}

Socket wrench

Torx bolts (2)

P-VRZR- 138

- 61 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 65/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 66/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

GE actuator pin (3) Assemble the GE actuator pin in the control

sleeve groove.

P-VRZR- 143

GE actuator (4) Move the GE actuator in an axial direction

as shown by the arrow in the figure at left
and confirm that the actuator moves
smoothly.
Advice
• Do not force the GE actuator. Forcing it
may damage the seal ring.
• The GE actuator will not move if its pin
is not inserted into the control sleeve
groove. If it will not move, remove the
GE actuator and again insert the pin into
P-VRZR- 144
the groove.
GE actuator (5) Move the GE actuator fully toward the full
side (ie, the head side).
Advice
If the GE actuator is positioned toward the
drive shaft side, it may not be possible to
measure the pre-stroke.

P-VRZR- 145

Holder Torx bolts (6) (6) Secure the GE actuator to the pump housing
using the torx bolts.
Advice
Tighten diagonally opposed torx bolts
gradually and uniformly to the specified
torque.
Bit
Specified torque: 7.0 ~ 10.0 N·m
{0.7 ~ 1.0 kgf·m}
Tool name Part no Remarks

Holder 157915-9820
Pump housing P-VRZR- 146 Bit 157915-9600 T30

- 63 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 67/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Magnet valve assembly (8) Magnet valve assembly installation

GE actuator (1) Install the magnet valve assembly to the GE
Magnet valve
actuator.
O-ring Advice
Spring Ensure the filter is installed securely.

Armature

Gauze filter
P-VRZR- 147

(2) Tighten the magnet valve assembly using a

Magnet valve assembly
torque spanner.
Spanner
Specified torque: 20.0 ~ 25.0 N·m
{2.0 ~ 2.5 kgf·m}

P-VRZR- 148

(9) Pre-stroke adjustment

Gaskets (2) (1) Connect the fuel hose to the injection pump
using the adapter.
Adapter Tool name Part no Remarks

Injection pump
Adapter 157977-8000
Gasket 026512-1640

Hose
P-VRZR- 149

(2) Install plugs to where the distributor head

and GE actuator overflow valves were
Plugs
removed.
Advice
Install any suitable plugs to maintain pump
chamber air tightness.

P-VRZR- 150

- 64 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 68/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

(3) Remove cylinder B’s delivery valve holder

Pipe assembly and assemble the pipe assembly to cylinder
B.
Tool name Part no Remarks
Cylinder B
Pipe assembly 157845-9520

P-VRZR- 151

(4) Connect the direct current harness to the

Magnet valve assembly
magnet valve.
Direct current harness Advice
Magnet valve supply voltage
• 12V specification: 12V

P-VRZR- 152

Injection pump
(5) Turn the pump test bench drive switch ON.
(6) Supply test oil to the injection pump at the
specified pressure (20.0 kPa {0.2 kgf/cm2}).
Advice
Leave the drive switch ON. Do not turn the
drive switch OFF until pre-stroke adjustment
has been completed.

P-VRZR- 153

(7) Turn the pump test bench flywheel about

Flywheel one turn in the specified direction of rotation
u s in g th e le v e r a n d u s e th e a n g le
measurement display to confirm that it turns
smoothly.

Lever

P-VRZR- 154

- 65 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 69/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 70/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

REASSEMBLY

Forked plates for 4 cylinders

RBAJ part no Bosch part no Stamping Pre-stroke variation (°)
149615-0001 9 443 612 824 A -3.03
149615-0101 9 443 612 825 B -2.50
149615-0201 9 443 612 826 C -1.97
149615-0301 9 443 612 827 D -1.43
149615-0401 9 443 612 828 E -1.07
149615-0501 9 443 612 829 F -0.54
149615-0601 9 443 612 830 G 0
149615-0701 9 443 612 831 H 0.54
149615-0801 9 443 612 832 I 1.07
149615-0901 9 443 612 833 J 1.43
149615-1001 9 443 612 834 K 1.97
149615-1101 9 443 612 835 L 2.50
149615-1201 9 443 612 836 M 3.03

(11) Remove the pipe assembly from cylinder

CPV holder B and replace it with the CPV holder.
Replace the gasket at the same time.

Cylinder B

P-VRZR- 158

Plugs
(12) Tighten the CPV holder using a socket
wrench.
Specified torque: 44.0 ~ 54.0 N·m
{4.5 ~ 5.5 kgf·m}
Tool name Part no Remarks
Socket wrench 157914-3600

CPV holder (13) Remove the plugs.

Socket wrench P-VRZR- 159

- 67 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 71/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

1. ADJUSTMENT CONDITIONS
[1] Test equipment
(1) Pump test bench EPS815
(2) KMA802
(3) Oil cooler (1 687 010 130)
(4) Adjustment software operating environment
Windows 2000 PRO (at least Service Pack 2.0) English language version;
Windows OS
Control Panel - Regional Options, Your locale: English (United Kingdom or United States)

Clock speed Personal computer equipped with Pentium CPU (clock speed at least 333 MHz)

Memory At least 128 MB usable memory

Hard disk At least 20 MB space

Display Resolution: at least 1027 x 768, number of display colors: high color minimum (16 bit)

Drive devices CD-ROM drive, floppy disk drive

At least 2 communication ports (2 necessary for controller assembly)

Additional devices
Mouse, keyboard

Note:
Refer to the Installation Manual, MC-02 TESTER SOFTWARE, ADJUSTMENT AND INSPECTION
DATA, Publication No. ED14E-11011, for details of personal computer settings and software
installation procedures.
[2] Fuel piping
(1) Injection system piping diagram
Nozzle and nozzle holder assembly (1 688 901 035) Tubes
Cooling unit

Injection tubes

Joint assembly (157641-6820)

Injection pipes (157808-4720) P-VRZR- 390

- 68 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 72/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

(2) Fuel piping

Key no RBAJ part no Bosch part no Part name Qty Remarks
1 157971-1020 9 443 613 442 Piping assembly - For VRZ overflow fuel piping
1/1 157971-1100 9 443 613 443 Bolt 1 For distributor head overflow
1/2 026512-1640 9 421 617 041 Gasket 6 For distributor head overflow
1/3 029711-2180 9 442 610 444 Eye 2 For distributor head overflow
1/4 157971-1000 9 443 613 444 Adapter 1 For distributor head overflow
1/5 017211-2010 9 442 611 983 Hose clip 2 For distributor head overflow
1/6 157986-8100 9 443 613 445 Hose 1 For distributor head overflow
1/7 026510-1340 9 442 610 043 Gasket 1 For distributor head overflow

Piping outline

Pressure gauge

Overflow measurement hose

1/5 1/4
1/1 1/2 1/3
1/6 1/2
Multi-way cock
1/5

1/7
Test oil hose

P ump c hamber pres s ure

Temperature sensor cable measurement hose
P-VRZR- 391

- 69 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 73/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

[3] Wiring outline

(1) Controller assembly wiring
Injection pump

Tool connection 232C cable

Connection: cross connection (2 pin, 3 pin cross)
(157966-4720)

Tool connection 232C cable

Connection: straight connection
(157966-4620)

Intermediate harness
Personal computer
(157966-2421) Intermediate harness
(157966-5720)
Dsub 9 pin

FCV GND harness

Dsub 25 pin
(157966-4820)

Dsub 7 pin

ROM harness
(157966-5020)

Dsub 9 pin

To AC100V - AC120V or
AC200V - 240V power source VRZ and COVEC-F Main harness Earth to injection pump
(157966-4420 or 157966-4520) controller unit (157966-4920) or pump test bench P-VRZR- 392

(2) Wiring connections inside controller unit

PC

COM2 COM1

RS232C RS232C
COM2 COM2
VRZ & COVEC-F (ROM) CONTROLLER 25 pin 9 pin

AC ROM
100 - 120V ROM writer ROM
cable
200 - 240V

ROM
lamp
ECU
AC lamp 4D56 Injection
socket (COVEC-F) Main pump
DC 5V cable
Constant ECU
power supply
FCV switch FCV line
GE
CSP
Main power DC 24V TPS
switch Constant ECU
power supply lamp 4M41 TCV
(VRZ) Main
cable TF
ECU
DC 12V FCV
Constant FCV switch FCV line
power supply FCV line Main
cable
1
0 2 FCV
Power switch
lamp Sub-switch ECU
3 lamp WL
(COVEC-F)
ECU
Selector 4
switch

P-VRZR- 395

- 70 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 74/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

[4] Related materials

No. Publication No. Remarks

When installing the ECU assembly for the controller unit, refer to the installation
1 ED14E-11021
instructions included with the controller unit.

When installing the adjustment software, refer to the installation manual included with the
2 ED14E-11011
CD-ROM.

Note:
Where updating of adjustment data and inspection data is indicated, copy the data from the ESPI
(ZW)’s CD-ROM.

- 71 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 75/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 76/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Key
Name Use and purpose
no
Turn to align with ECU in use.
0: All OFF
1: No. 1 ECU
11 ECU changeover switch 2: No. 2 ECU
3: No. 3 ECU
4: Spare ECU
Power sub-switch for controller unit for VRZ adjustment. Press once to turn ON.
12 Sub-switch
When turned ON for use, orange lamp lights. Press once again to turn OFF.

13 ROM pilot lamp Green lamp lights when ROM in use.

ROM wire harness connecting For connecting injection pump's ROM harness connector to ROM controller
14
terminal using wire harness.

CAUTION
If you smell any unusual smell or see smoke or sparks when using the controller unit, turn the
power switch OFF immediately and stop using the controller unit.
Fire may result if you continue to use the controller unit.

Advice
• Do not use the controller unit with oily hands. The oil may stick to the dials and cause
improper resistor contact inside the controller unit, preventing proper operation.
• Before turning the power switch ON, confirm that the wire harnesses are properly
connected.

- 73 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 77/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

[2] Rear panel

CE

P-VRZR- 345

Key
Name Use and purpose
no

1 AC100V - 120V power or Connect to AC100V - 120V, 50/60Hz power source or

AC 200V - 240V power terminal AC 200V - 240V power source, 50/60Hz.
Controller unit power switch.
2 Main switch (breaker)
Turn ON when in use (position at 'I'). Position at 'O' to turn OFF.
D-sub 9 pin cable connection
3 Connects RS232C cable to personal computer (for GE).
(COM1)
D-sub 25 pin cable connection
4 Connects RS232C cable to personal computer (for Q-ROM)
(COM2)

CAUTION

If you smell any unusual smell or see smoke or sparks when using the controller unit, turn the
power OFF immediately and stop using the controller unit.
Fire may result if you continue to use the controller unit.

Advice
• Do not use the controller unit with oily hands. The oil may stick to the dials and cause
improper resistor contact inside the controller unit, preventing proper operation.
• Before turning the power switch ON, confirm that the wire harnesses are properly
connected.

- 74 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 78/117
 7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

1. Password input

Disagreement

Agreement
2. ECU selection
[1] 4D56
[2] 4M41
[3] WL
[4] Manual operation
[5] Workshop name registration
[6] Exit

[1] or [2] or [3] [4] [5]

Part no. input Manual operation Workshop name registrati
[1] Adjustment
[2] Inspection
Input item
[1] Workshop name
- [2] Address
Pre-check 1.
7 
 5 
- [3] Telephone
[4] Fax
[5] Operator's name
[6] Password
Adjustment Inspection
Step 1-XX Adjustment Step 1-XX Inspection
Select "Registration" butto
StepXX + 1 ROM compensation

StepXX + 2 ROM writing

Confirmation
Repeat OK Repeat
measurement measurement OK
Adjustment result Inspection result
Push [MENU] button
(= Registration change
completed)
Print result Cancel Print result Cancel

OK
P 
-V 
R 
Final confirmation Final confirmation
Z 
R 
-
 3 
 9 
 6 

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 79/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

4. PUMP ADJUSTMENT TOOL MONITOR SCREEN

MC-02 TESTER

Copyright(C) 2001-2003 by Bosch Automotive Systems Corporation

Service tools for pump adjustment Version1.0 RBAJ

1 ROM COVEC-F MITSUBISHI 12V

Inspection/adjustment

2 VRZ MITSUBISHI 12V

Inspection/adjustment

ROM COVEC-F MAZDA 12V

3 Inspection/adjustment

4 Manual operation

5 Workshop name registration

Exit
6

P-VRZR- 346

No. Name Use and purpose

1 4D56 model engine's COVEC-F type Select for inspection / adjustment of COVEC-F injection pump for
injection pump inspection / adjustment key Mitsubishi 4D56 model engine
2 4M41 model engine's VRZ type injection Select for inspection / adjustment of VRZ injection pump for
pump inspection / adjustment key Mitsubishi 4M41 model engine
3 WL model engine's COVEC-F type Select for inspection / adjustment of COVEC-F injection pump for
injection pump inspection / adjustment key Mazda WL model engine
4 Manual operation key For adjusting injection pump and engine's installation timing
5 Workshop registration key For workshop registration
6 Exit key To exit adjustment software

- 76 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 80/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

5. PUMP ADJUSTMENT TOOL MONITOR SCREEN OUTLINE

Inspection and adjustment step screen
Inspection and adjustment steps
Pump adjustment tools for service Input part no.
monitor screen

Pump information
1 N 0 r/min
44-6666
44-3032
000000000b 19
2 T 0.0 deg C 00000-000-0000b
VRZ 4M41
3 Rotation Right
20
Ua-ist V 4 cylinders
ECU MELCO
4 3 Mode Adjustment
Q 0.0 mm /st Pump type VRZ(12V) 21
5 Pt 0.000 MPa
6 Qo 0.0 l/h
7 TF
2001-01-15 11:28:44
22
V MENU Part number input
17
8 VTPS V
9 16
TPS V
10
Only items necessary for each TA mm
step are displayed. 11 DQ 0.0 mm3/st
23
Circled numbers indicate fields 24
where input is necessary. 12 Zero set

13 Soll-cor

Step information
Back Next No. STEP N Soll Soll-cor TCVF DTCV

18 Step status
Comment
03 P_cham_ADJ
PT standard point
1000rpm 2.91v 0.00mv 60Hz 100%

14 Next
Sequence 03 / 32 After values are input, push 'Next' button. 25
15 Select 04 500rpm 2.50v 60Hz 0%
P-VRZR- 347

No. Name Use and purpose

1 Pump speed input N: pump speed Input the pump's speed.
2 Test oi l temperature i nput T: test oi l temperature Input the test oi l temperature.
3 Actual control sleeve position voltage U α soll: actual control sleeve position Displays actual control sleeve position voltage.
display voltage
4 Pump injection quantity input Q: pump injection quantity Input pump's injection quantity.
5 Pump chamber pressure input Pt: pump chamber pressure Input pump's chamber pressure.
6 Pump overflo w quantity input Qo: pump overflow quantity Input pump's overflo w quantity.
7 TF output display TF: fuel temperature Displays fuel temperature output voltage.
8 VTPS output display VTPS: voltage at 0 mm timer stroke Displays VTPS output voltage (voltage at 0 mm timer stroke).
9 TPS output display TPS: timer piston sensor output voltage Displays TPS (timer piston sensor) output voltage.
10 TA output display TA: timer stroke Displays TA (timer stroke) output.
11 Variation between cylinders display DQ: variation between cylinders Input pump's variation between injection quantities.
12 Zero setting key TPS output voltage at TA = 0 mm can be set at 0 V.
13 Target control sleeve position Any control sleeve position can be set by setting the compensation

compensation voltage key voltage.

14 NEXT key To set at next step.
15 Keys for moving to next or previous step To set at any step ( BACK, NEXT).
16 Menu key To set at MENU display.
17 Part number input key To set at part number input display.
18 Step status display Displays step status. Changes from red to green when all items
are within specifications.
19 Part number, seri al number di splay Displays pump information part number (specifi cati on, pump) and
serial number (pump, GE).
20 Specification display Displays pump information specifications.
21 Measurement mode display Displays pump information measurement mode (inspection,
adjustment).
22 Measurement date display Displays date and time of measurements.
23 Status display Displays step status. Green: within specifications; red: outside of
specifications.
24 Current step display Displays current step items.
25 Next step display Displays next step's items.

- 77 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 81/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

6. MANUAL OPERATION DISPLAY

Second timing adjustment (manual operation)
Pump adjustment tools for service Second timing adjustment (manual operation)

MC-02 TESTER
Manual operation
ECU reader data

Item Value Unit Item Value Unit

1 GE Vist V TPS Vist V

Item Value Unit Item Value Unit

TF deg C Np r/min

Select ECU
5 ROM COVEC-F MITSUBISHI 12V VRZ MITSUBISHI 12V ROM COVEC-F MAZDA 12V

ECU configuration data

Input
2 GE Soll V 1. Values must be input for GE soll, TCV Duty and TCV Frequency.
2. Np values do not appear at VRZ pump adjustment.
GE Soll-cor mV
TCV Duty %
TCV Frequency Hz
3 Initialize ECU

4 Menu

P-VRZR- 348

No. Name Remarks

1 Control sleeve position actual voltage Displays actual control sleeve position voltage.
display
2 Control sleeve position target voltage By operating the input keys, the control sleeve position can be set
display for the engine specified in No. 5.
3 Initialize ECU Clear display values
4 MENU Displays MENU screen.
5 Select ECU Select the ECU for the engine.

- 78 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 82/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

7. WORKSHOP DISPLAY
Second timing adjustment (manual operation)
Pump adjustment tools for service Workshop name registration

MC-02 TESTER
Workshop name registration

1 Workshop name RBAJ

2 Address JAPAN
3 Telephone 000-000-0000
4 Fax 111-111-1111

5 Operator's name sse

6 Password ****

Input items and select Registration button.

7 Menu Registration 8
P-VRZR- 350

No. Name Remarks

1 Workshop name Input comany name.
2 Address Input company address.
3 Telephone Input telephone number.
4 Fax Input fax number.
5 Operator's name Input operator's name.
6 Password Input password and change password.
7 MENU Can be used to set MENU display.
8 Registration For keeping registered items.

WORKSHOP REGISTRATION
MC-02 TESTER

Copyright(C) 2001-2003 by Bosch Automotive Sys tems Corporation

(1) Select ‘Workshop name registration.’
Service tools for pump adjustment Version1.0 RBAJ

ROM COVEC-F MITSUBISHI 12V

Inspection/adjustment

VRZ MITSUBISHI 12V

Inspection/adjustment

ROM COVEC-F MAZDA 12V

Inspection/adjustment

Manual operation

(1)
Workshop name registration

Exit

P-VRZR- 346

(2) Input the company name, etc, in the fields

MC-02 TESTER
Workshop name registration on the screen.
(3) Click the ‘Registration’ button.
Workshop name RBAJ
Address JAPAN Note:
Telephone
(2)
The default password at setup is ‘RBAJ’.
000-000-0000
Fax 111-111-1111
Operator's name sse

Password ****
Input a new password if desired. (The only limit
to the number of figures and letters in the
Input items and select Registration button.
password is the size of the input field.)
(3)

Menu Registration

P-VRZR- 350

- 79 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 83/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

8. ADJUSTMENT
Adjustment sequence
Recording the pump and GE serial numbers  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 81 [1]

Preparation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 81 [2], 82 [3]

Part no. input and installation confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 83 [4]

Warming-up operation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 84 [5]

Pre-stroke adjustment  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 64 (9)

Pump chamber pressure adjustment  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 85 [6]

Standard injection quantity point adjustment  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 86 [7]

Pump chamber pressure confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 86 [8]

TPS zero setting  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 87 [9]

Timer stroke and characteristic confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 88 [10]

Non-injection confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 88 [11]

Injection quantity compensation point adjustment  ○ ○ ○ ○ ○ ○ 

See page 89 [12]

Compensation ROM interpolation calculation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 89 [13]

Writing to the compensation ROM  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 90 [14]

Magnet valve operation confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 90 [15]

Second timing adjustment  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 94 (4)

Finish

- 80 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 84/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 85/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Fixing stand (8) Reconfirm that the coupling and the fixing
stand bolts and nuts are securely tightened.
(9) Set the 20NP pump test bench’s test oil
outlet temperature at 45°C.
(10) Set the cooling unit oil delivery pressure
lever at ‘80 kPa {0.8 kgf/cm2}’ or less.

P-VRZR- 355

FCV (magnet valve) ON/OFF switch (11) Connect the wire harness to the controller
Sub-switch unit’s No 2 ECU connector.
(12) Turn the main switch on the rear of the
controller unit ON.
(13) Set the No 1 ~ No 4 changeover switch at
No 2.
(14) Turn the FCV (magnet valve) ON/OFF
switch ON to energize the magnet valve.
(15) Turn the sub switch on the front of the
ECU for VRZ type controller unit ON.
injection pump
No. 1 ~ No. 4 changeover switch
P-VRZR- 397

[3]Adjustment software set up:

preparation
(1) Turn the computer and the monitor power
switches ON.

Monitor power switch

Computer power switch

P-VRZR- 210

(2) Start the ‘Service tools for pump adjustment’

software.
MC-02 TESTER
(3) Input the password and press the ‘Enter’ key.
Precaution
Advice
Password is required to actuate adjustment tools. Input the initial default password ‘RBAJ’ or
Input password and press ENTER key. your own password.

(3)
P-VRZR- 357

- 82 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 86/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

[4] P a r t n u m b e r i np u t and
MC-02 TESTER

Copyright(C) 2001-2003 by Bosch Automotive Syst ems Corporation

Service tools for pump adjustment Version1.0 RBAJ
confirmation
ROM COVEC-F MITSUBISHI 12V
(1) Select the ‘VRZ [Mitsubishi 12V] Inspection/ 
Inspection/adjustment

VRZ MITSUBISHI 12V

(1) adjustment’ button.
Inspection/adjustment

ROM COVEC-F MAZDA 12V

Inspection/adjustment

Manual operation

Workshop name registration

Exit

P-VRZR- 346

(2) When the dialog shown at left appears, input

MC-02 TESTER
Part number input the specified part number (6 digits) and
If number input is correct, select Next button.
If you need to input a different number, select Clear button.
press ‘Enter’.
(2) Specified part no. Pump serial no. (4)
(3) Input the pump part number (last 6 digits)
(6 digits)
Pump part no.
446613

443062
(10 digits)
GE serial no.
0880052496

5062008852056 (5)
and press ‘Enter’.
(3) (last 6 digits) (13 digits)

Systemspecifications
Engine model VRZ_4M41
1. Specified part no.
Pump Pump
OEM
Specified part no.
(4) Input the pump serial number (10 digits) and
part no. type

press ‘Enter’.
Adjustment Inspection
Rotation Right 104700-304* 003040 008040
104700-305* COVEC-F 003051 008051
Pump cylinders 4 cylinders 104700-306* MITSUBISHI 003060 008060
ECU MELCO 109144-305*
109144-306*
VRZ

104700-055* COVEC-F MAZDA

44-6613 44-8813

000550 008550
(5) Input the GE’s serial number (13 digits) and
2. Pump part no.

Mode Adjustment
Example:
Full pump no.
109144-3052
104700-0551
Input pump part no.
443052
000551
press ‘Enter’.
(6)
(6) Press the ‘Next’ key.
Menu Clear Next

P-VRZR- 358

(7) Confirm that the screen changes to the

MC-02 TESTER
Setup confirmation injection system piping display.
Note:
Installationconfirmation
Click on appropriate item Key no. Part name Part no. Note
and explanatory illustration is displayed. 1 Injection pipe 157808-4720
2 Nozzle & nozzle holder assembly 1 688 901 035
1. Injection system piping

2. Overflow piping
3
4
Joint
Injection tube
Same as VP44
Clicking the different buttons (1. Injection system
3. Adjustment controller wiring

3
piping, 2. Overflow piping, 3. Adjustment
4. Operation sequence

2 4 controller wiring, and 4. Operation sequence)

displays different Setup confirmation screens.

If necessary to proceed
after confirmation, push Next button.
1
Menu

Back Next

P-VRZR- 359

- 83 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 87/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Service tools for pump adjustment Adjustment display

[5] Warming-up operation
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

44-6613

44-3062
(1) Set the pump test bench delivery pressure
T 0.0 deg C
Pump serial no.

GE serial no.
0880052496
50620-088-52056 at the specified 40 kPa {0.4 kgf/cm2}.
(4)
(2) Confirm that the sequence is 01/31.
Engine model VRZ_4M41
Ua-ist V Rotation Right
Pump cylinders 4 cylinders

Q 0.0 mm3/st ECU

Mode
MELCO

Adjustment
(3) Run the injection pump at the specified
Pump type VRZ (12V)
speed N (see figure at left).
05/04/03 13:20:52 (4) Measure N, T and Q on the pump test bench
Part number input

and input the values.

Menu

Step information
No. S tep name N Soll Soll-cor Frequency Duty
(5) Step status Present step 01 Warm-up 300r/min 2.80v 0.00mv 60Hz 100%

Next
Comment Check for fuel leaks.
Note:
(6)
U α ist is displayed automatically.
Sequence 01 / 31
After values are input, push Next button.
Select 02 Warm-up 1000r/min 2.91v 0.00mv 60Hz 100%

(2)
(5) Confirm that the Step status field is green.
P-VRZR- 360
(6) Proceed to the next step.
Advice
If U α ist values are not as specified, press
the ‘Next’ button several times. Then, return
to Step the
01/31 using theand
back arrow.that U α
Repeat Step 01/31 confirm
ist values are as specified.
Note:
If not as specified after confirming U α ist several
times, the GE may be faulty.

Service tools for pump adjustment Adjustment display

(7) Confirm that the sequence is 02/31.
Status Item Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

44-6613

44-3062
(8) Run the injection pump at the specified
T 0.0 deg C
Pump serial no.

GE serial no.
0880052496
50620-088-52056
speed N (see figure at left).
(9)
Ua-ist V
Engine model

Rotation
VRZ_4M41
Right (9) Measure N, T and Q on the pump test bench
Pump cylinders 4 cylinders

Q 0.0 mm /st 3 ECU

Mode
MELCO

Adjustment
and input the values.
Pump type VRZ (12V)
Note:
05/04/03 13:21:45
U α ist is displayed automatically.
Step information
No. S tep name N Soll
Menu

Soll-cor
Part number input

Frequency Duty
(10) Confirm injection.
(13) (11) Confirm that no fuel leaks from the
Step status Present step 02 Warm-up 1000r/min 2.91v 0.00mv 60Hz 100%
Comment Warm-up
Next
(14) Sequence

Select
02 / 31

03
After values are input, push Next button.
P-cham_ADJ 1000r/min 2.91v 0.00mv 60Hz 100%
injection pump fuel piping connections.
(7) P-VRZR- 361 CAUTION
If there are any fuel leaks, if there is no
injection or if any unusual noises occur
during operation, stop test bench operation
immediately and inspect the pump.
(12) Confirm that the injection pump is
operating normally.
(13) Confirm that the Step status field is green.
(14) Proceed to the next step.
Advice
Because the test oil temperature takes
longer to increase in cold weather, turn the
pump test bench on earlier.

- 84 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 88/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 89/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Service tools for pump adjustment Adjustment display

Status I tem Measured / input value Unit Specification Tolerance Pump information
[7] Standard injection quantity point
N 0 r/min
Specifiedpartno.

Pump part no.

Pump serial no.

44-6613

44-3062
0880052496
adjustment
T 0.0 deg C GE serial no.

Engine model
50620-088-52056

VRZ_4M41
(1) Confirm that the sequence is 04/31.
(3) Ua-ist V Rotation

Pump cylinders
Right
4 cylinders (2) Run the injection pump at the specified
Q 0.0 mm3/st MELCO

speed N (see figure at left).

ECU

Mode Adjustment

DQ 0.0 mm /st 3 Pump type VRZ (12V)

(3) Measure N, T, Q and DQ on the pump test

Menu
05/04/03 13:23:05
Part number input
bench and input the values.
(9)
Step information
Step status Present step
No.
04
S tep name
Rough-Q_ADJ
N
1000r/min
Soll
2.91v
Soll-cor
0.00mv
Frequency
60Hz
Duty
100%
Note:
Next
Comment Standard Q adjustment (GE adjustment)
U α ist is displayed automatically.
(10) Sequence 04 / 31 After values are input, push Next button.
Select 05 P-cham_ADJ 1000r/min 2.91v 0.00mv 60Hz 100%
(4) If Q is as specified, perform steps (9) and
(1) P-VRZR- 363
(10). If Q is not as specified, adjust as
described below.
Injection quantity decrease (5) To adjust the fuel injection quantity, loosen
(move GE actuator toward drive side)
the torx bolts so that the GE actuator can
Move GE actuator to adjust
move a little.
(6) Move the GE actuator in the drive shaft’s
axial direction to adjust the full load injection
Injection quantity increase
quantity. (To increase the injection quantity,
(move GE actuator toward move the GE actuator toward the distributor
distributor head side) head. To decrease the injection quantity,
move the GE actuator toward the drive side.)
Record the measured injection quantity and
GE actuator the position of the GE actuator to facilitate
P-VRZR- 355
adjustment.
(7) Following adjustment, tighten the torx bolts

to the specified
Specified torque: torque.
7 ~ 10 N.m
{0.7 ~ 1.0 kgf.m}
(8) Measure N, T, Q and DQ again on the pump
test bench and input the values.
(9) Confirm that the Step status field is green.
(10) Proceed to the next step.

Service tools for pump adjustment Adjustment display

[8]Pump chamber pressure
Status I tem Measured / input value Unit Specification Tolerance Pump information
Specifiedpartno. 44-6613

(1) confirmation
N 0 r/min Pump part no. 44-3062

Confirm that the sequence is 05/31.

Pump serial no. 0880052496
T 0.0 deg C GE serial no. 50620-088-52056

(2) Run the injection pump at the specified

Engine model VRZ_4M41

(3) Ua-ist V Rotation Right

Pump cylinders 4 cylinders

Pt 0.000 MPa ECU

Mode
MELCO

Adjustment
speed N (see figure at left).
Qo 0.0 I/h Pump type VRZ (12V)
(3) Measure N, T, Pt and Qo on the pump test
TF V
05/04/03 13:23:42 bench and input the values.
Part number input

Note:
Menu

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Present step
(5) Step status 05 P-cham_ADJ 1000r/min 2.91v 0.00mv 60Hz 100%

Next
Comment Reconfirmation of PT standard point
U α ist and TF are displayed automatically.
(6)
(4) Confirm the pump chamber pressure.
Sequence 05 / 31
After values are input, push Next button
Select 06 Zero_set 500r/min 2.50v 0.00mv 60Hz 100%

(1) P-VRZR- 364

(5) Confirm that the Step status field is green.
(6) Proceed to the next step.
Advice
Recheck the feed pump.

- 86 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 90/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 91/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Service tools for pump adjustment Adjustment display

[10] Timer stroke and characteristic
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

Pump serial no.

44-6613

44-3062
confirmation
0880052496

(3)
T 0.0 deg C GE serial no.

Engine model
50620-088-52056

VRZ_4M41
(1) Confirm that the sequence is 07/31.
Ua-ist V Rotation

Pump cylinders
Right
4 cylinders
(2) Run the injection pump at the specified
Pt 0.000 MPa ECU

Mode
MELCO

Adjustment speed N (see figure at left).

VTPS V Pump type

(3) Measure N, T and Pt on the pump test bench

VRZ (12V)

TA mm
Menu
05/04/03 13:20:52
Part number input
and input the values.
Step information
Step status Present step
No. S tep name
Timer_TA
N Soll Soll-cor Frequency Duty Note:
(5) 07 100r/min 2.41v 0.00mv 60Hz 100%

Next
Comment 100r/min
U α is t, V T P S a n d T A a re d is p la y e d
(6) Sequence 07 / 31 After values are input, push Next button.
Select 08 Timer_TA 50r/min 2.41v 0.00mv 60Hz 100% automatically.
(1) P-VRZR- 366 (4) Confirm that the timer stroke is within the
specifications.
TPS
(5) Confirm that the Step status field is green.
(6) Proceed to the next step.
Note:
Because the TPS standard point shim was
Timer stroke adjusting shim adjusted in Step 06/31, it cannot be changed.

Spring

Pump housing P-VRZR- 137

Confirm 50 revolutions (Step 08/31) ~ 1,900

Service tools for pump adjustment Adjustment display
Status I tem Measured / input value Unit Specification Tolerance
revolutions (Step 16/31) using the same
Pump information
Specifiedpartno. 44-6613
N 0 r/min Pump part no. 44-3062

T 0.0 deg C
Pump serial no.

GE serial no.
0880052496
50620-088-52056
procedure used for 100 revolutions (Step 7/31)
Ua-ist V
Engine model

Rotation
VRZ_4M41
Right
above.
Pt 0.000 MPa
Pump cylinders

ECU
4 cylinders
MELCO Advice
Repeat Step 06/31 if the timer stroke is not
Mode Adjustment

VTPS V Pump type VRZ (12V)

TA mm as specified.
05/04/03 13:25:27
Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Step status Present step 08 Timer_TA 50r/min 2.41v 0.00mv 60Hz 100%
Comment 50r/min
Next
Sequence 08 / 31 After values are input, push Next button.
Select 09 Timer_TA 325r/min 1.53v 0.00mv 60Hz 100%

P-VRZR- 367

Service tools for pump adjustment Adjustment display

[11] Non-injection confirmation
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

44-6613

44-3062
(1) Confirm that the sequence is 17/31.
(2) Run the injection pump at the specified
Pump serial no. 0880052496

T 0.0 deg C GE serial no. 50620-088-52056

speed N (see figure at left).

Engine model VRZ_4M41
(3) Ua-ist V Rotation Right
Pump cylinders 4 cylinders

Q 0.0 mm3/st ECU

Mode
MELCO

Adjustment
(3) Measure N, T, Q and DQ on the pump test
DQ 0.0 mm3/st Pump type VRZ (12V)
bench and input the values.
05/04/03 13:35:08
Note:
Part number input

U α ist is displayed automatically.

Menu

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Present step
(4) Step status 17 Q_characteristics 2300r/min 0.87v 0.00mv 60Hz 100%

Next
Comment Confirm no nozzle injection.
(4) Confirm that the Step status field is green.
(5) Sequence 17 / 31
After values are input, push Next button.
Select
18 Cor-Q_ADJ 1900r/min 3.73v 0.00mv 60Hz 100%

(5) Proceed to the next step.

(1)
P-VRZR- 368

- 88 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 92/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Service tools for pump adjustment Adjustment display

[12] Injection quantity compensation
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

44-6613

44-3062
point adjustment
Pump serial no. 0880052496
T 0.0 deg C GE serial no.

Engine model
50620-088-52056

VRZ_4M41
(1) Confirm that the sequence is 18/31.
(3) Ua-ist V Rotation

Pump cylinders
Right
4 cylinders
(2) Run the injection pump at the specified
Q 0.0 mm3/st ECU

Mode
MELCO

Adjustment speed N (see figure at left).

DQ 0.0 mm3/st Pump type

(3) Measure N, T, Q and DQ on the pump test

VRZ (12V)

(4) Soll-cor Menu

05/04/03 13:36:03
Part number input
bench and input the values.
Step information
No. S tep name N Soll Soll-cor Frequency Duty Note:
(6) Step status Present step 18 Cor-Q_ADJ 1900r/min 3.73v 0.00mv 60Hz 100%

Next
Comment Correction point 10
U α ist is displayed automatically.
(7) Sequence 18 / 31
After values are input, push Next button.
Select 19 Cor-Q_ADJ 1900r/min 1.53v 0.00mv 60Hz 100% (4) If the injection quantity is not as specified,
(1) P-VRZR- 369
press the ‘Soll-cor’ setting, input the soll
compensation voltage and adjust the
injection quantity to the specification.
(5) Measure the injection quantity and confirm
that it is as specified.
Advice
With the Soll-cor setting, the compensation
voltage range differs with the service data
or the calculation file. If the compensation
voltage range is exceeded, a ‘Reset’
message is displayed.
When the injection quantity is greater than
the specification
Input a minus to the compensation voltage and
input the value
Service tools for pump adjustment Adjustment display

Status Item Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno. 44-6613
When the injection quantity is less than the
Pump part no.

Pump serial no.

44-3062
0880052496 specification
T 0.0 deg C GE serial no. 50620-088-52056

Ua-ist V
Engine model

Rotation
VRZ_4M41
Right
Input the value only to the compensation voltage
Pump cylinders 4 cylinders

Q 0.0 mm3/st ECU

Mode
MELCO

Adjustment
(6) Confirm that the Step status field is green.
DQ 0.0 mm3/st Pump type VRZ (12V)
(7) Proceed to the next step.
05/04/03 13:36:43
Soll- cor

Confirm compensation point 9 (Step 19/31) ~

Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Step status Present step 19 Cor-Q_ADJ 1900r/min 1.53v 0.00mv 60Hz 100%

Next
Comment Correction point 9 compensation point 1 (Step 27/31) using the
same procedure used for compensation point
Sequence 19 / 31
After values are input, push Next button.
Select 20 Cor-Q_ADJ 1000r/min 2.91v 0.00mv 60Hz 100%

10 (Step 18/31) above.

P-VRZR- 370

After
pressadjusting thebutton
the ‘Next’ compensation point 1,
to automatically
Service tools for pump adjustment Adjustment display
Status I tem Measured / input value Unit Specification Tolerance Pump information
Specifiedpartno. 44-6613
proceed to Step 28/31.
Pump part no. 44-3062
Pump serial no. 0880052496
GE serial no. 50620-088-52056

Engine model

Rotation
VRZ_4M41
Right
[13] Compensation ROM interpolation
Injection quantity input data is outside
specification after correction point 1.
Pump cylinders

ECU

Mode
4 cylinders
MELCO

Adjustment
calculation
Pump type VRZ (12V)
Note:
05/04/03 13:43:00
• In Step 28/31 the adjustment software
Step information
No. S tep name N Soll
Menu

Soll-cor
Part number input

Frequency Duty
automatically performs the calculations.
• If the compensation voltage Soll values are
Step status Present step 28 Q-ROM_CAL 0r/min 0.00v 0.00mv 60Hz 0%
Comment Q-ROM intermediate point calculation
Next
Sequence

Select
28 / 31
After values are input, push Next button.
ROM_overwrite 0%
not correct, compensation calculations are
29 0r/min 0.00v 0.00mv 60Hz

not performed and an error is displayed. If

P-VRZR- 371 an error is displayed, repeat Step 18/31.

- 89 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 93/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Service tools for pump adjustment Adjustment display

[14] Writing to the compensation ROM
Status I tem Measured / input value Unit Specification Tolerance Pump information
Specifiedpartno.

Pump part no.

44-6613

44-3062
(1) Press Step 28/31 to automatically display
Pump serial no.

GE serial no.
0880052496
50620-088-52056
the step.
Engine model

Rotation
VRZ_4M41
Right (2) The adjustment software automatically
Injection quantity input data is outside Pump cylinders 4 cylinders

specification after correction point 1.

ECU MELCO
writes the compensation Q data to the
Mode Adjustment
Pump type VRZ (12V)
injection pump’s Q adjustment ROM.
05/04/03 13:43:34
Advice
Step information
No. S tep name N Soll
Menu

Soll-cor
Part number input

Frequency Duty
Never touch the computer, the injection
pump or the connecting wire harnesses
Step status Present step 29 ROM_overwrite 0r/min 0.00v 0.00mv 60Hz 0%
Comment Overwrite Q-ROM.
Next
Sequence

Select
29 / 31

30 Stop_Q
After values are input, push Next button.
1000r/min 2.91v 0.00mv 60Hz 0%
while writing to the ROM.
(1) P-VRZR- 372

Service tools for pump adjustment Adjustment display

Status Item Measured / input value Unit Specification Tolerance Pump information
[15]Magnet valve operation
N 0 r/min
Specifiedpartno.

Pump part no.

Pump serial no.

44-6613

44-3062
0880052496
confirmation
T 0.0 deg C GE serial no.

Engine model
50620-088-52056

VRZ_4M41
(1) Confirm that the sequence is 30/31.
(3) Ua-ist V Rotation

Pump cylinders
Right
4 cylinders (2) Run the injection pump at the specified
Q 0.0 mm3/st ECU MELCO

Mode

Pump type
Adjustment speed N (see figure at left).
VRZ (12V)

(3) Measure N, T and Q on the pump test bench

Menu
05/04/03 13:44:15
Part number input
and input the values.
Step information
Step status Present step
No.
30 Stop_Q
S tep name N
1000r/min
Soll
2.91v
Soll-cor
0.00mv
Frequency
60Hz
Duty
100%
Note:
U α ist is displayed automatically.
Comment Confirm no nozzle injection when the FCV is OFF.
Next
Sequence 30 / 31 After values are input, push Next button.
Select 31 Q_characteristics 0r/min 2.91v 0.00mv 60Hz 100%

(1)
P-VRZR- 373

FCV (magnet valve) ON/OFF switch (4) Turn the FCV (magnet valve) ON/OFF
switch OFF and confirm that non-injection
results.
Advice
To confirm non-injection from the nozzle,
look at the monitor screen and confirm that
non-injection occurs within a short time (6 ~
7 seconds).

P-VRZR- 356

Service tools for pump adjustment Adjustment display

(5) Measure N, T and Q again on the pump
Status Item

N
Measured / input value

0 r/min
Unit Specification Tolerance Pump information
Specifiedpartno.

Pump part no.

44-6613

44-3062
test bench and input the values.
T 0.0 deg C
Pump serial no.

GE serial no.
0880052496
50620-088-52056
(6) Confirm that the Step status field is green.
(5)
Ua-ist V
Engine model

Rotation
VRZ_4M41
Right
(7) Proceed to the next step.
Pump cylinders 4 cylinders

Q 0.0 mm3/st ECU MELCO

Mode Adjustment

Pump type VRZ (12V)

05/04/03 13:44:15
Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty

(6) Step status Present step

Comment
30 Stop_Q 1000r/min 2.91v 0.00mv 60Hz 100%
Confirm no nozzle injection when the FCV is OFF.
Next
(7) Sequence 30 / 31 After values are input, push Next button.

Select 31 Q_characteristics 0r/min 2.91v 0.00mv 60Hz 100%

P-VRZR- 373

- 90 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 94/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

[16] Second timing adjustment

Note:
The following describes the preparation for and
Sub-switch performance of automatic adjustment of second
timing.
(1) Injection pump disassembly
(1) Turn the sub-switch OFF.

P-VRZR- 356

Fuel piping Injection pump Coupling (2) Disconnect the intermediate harness
connectors.
(3) Disconnect the fuel piping.
(4) Remove the coupling.
(5) Remove the pump from the fixing stand.
(6) Remove the fixing stand.

Fixing stand
Harness connectors P-VRZR- 375

O-ring (2) Drive gear installation

(1) Temporarily assemble the O-ring and
bracket to the pump housing.
Nuts (3)

Bracket P-VRZR- 252

(2) Assemble the drive shaft key in the drive

shaft’s key groove.

Key

P-VRZR- 253

- 91 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 95/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 96/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

(3) Injection pump installation

(1) Attach the stand to the pump test bench.
Stand Tool name Part no Remarks
Stand 105781-0890

P-VRZR- 258

(2) Attach the injection pump to the stand.

Stand
(3) Pull the stand’s handle as shown in the figure
to fix the injection pump.

P-VRZR- 259

Pipe assembly (4) Remove the CPV from cylinder B and attach
the pipe assembly and the gasket.
Tool name Part no Remarks
Pipe assembly 157845-9520

P-VRZR- 260

Plugs (5) Connect the test oil hose to the injection

pump.
(6) Attach the plugs to where the GE and the
distributor head overflow valves were
removed.
Advice
Install any suitable plugs to maintain pump
chamber air tightness.

Test oil hose P-VRZR- 261

- 93 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 97/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

(7) Connect the controller assembly’s main

Main harness
harness and intermediate harness to the
injection pump’s GE connector.
Tool name Part no Remarks

Main harness 157966-4920

Intermediate
157966-5720
harness

Intermediate harness P-VRZR- 262

Adjusting device Chamfered tooth (8) Align the adjusting device’s pin hole with the
injection pump bracket’s pin. In this position,
attach the adjusting device to the injection
pump’s bracket and fix using the bolts.
Tool name Part no Remarks
Pin Rack
Adjusting
Rack teeth 105793-0020
Pin hole device

Advice
When aligning the adjusting device’s pin hole
with the bracket’s pin, position the adjusting
P-VRZR- 263 device’s rack teeth on either side of the drive
gear’s chamfered tooth.

(4)
(1) Second
Turn the timing adjustment
controller unit’s sub-switch ON.
(2) Supply test oil to the injection pump at the
Sub-switch specified pressure of 20 kPa {0.2 kgf/cm 2}.

P-VRZR- 356

Service tools for pump adjustment Adjustment display

(3) Confirm that the sequence is Step 31/31 (Q
characteristics).
Status I tem Measured / input value Unit Specification Tolerance Pump information
Specifiedpartno. 44-6613
N 0 r/min Pump part no. 44-3062
Pump serial no. 0880052496

T 0.0 deg C GE serial no. 50620-088-52056

Engine model VRZ_4M41

Ua-ist V Rotation Right
Pump cylinders 4 cylinders

Q 0.0 mm3/st ECU MELCO

Mode Adjustment

DQ 0.0 mm3/st Pump type VRZ (12V)

05/04/03 13:44:46
Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Step status Present step 31 Q_characteristics 0r/min 2.91v 0.00mv 60Hz 100%
Comment Second timing
Next
Sequence 31 / 31
After values are input, push Next button.
Select  _ 
Adjustment finished

(3) P-VRZR- 376

- 94 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 98/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Nuts (3) (4) L o o s e n th e in je c tion p u mp b ra c k e t

installation nuts.

P-VRZR- 264

FBB plate (5) Loosen the bolt preventing drive shaft

Bolt preventing drive rotation and remove the FBB plate.
shaft rotation

P-VRZR- 265

Pipe assembly Adjusting device (6) Insert the lever into the adjusting device and
turn the lever once in the reverse rotation
direction, then turn the lever in the direction
of rotation.
(7) Adjust so that test oil flows from cylinder B’s
pipe assembly at a rate of 1 drop / 3
seconds.

P-VRZR- 266

(8) Tighten the bolt preventing drive shaft

Bolt preventing drive rotation to fix the drive shaft.
shaft rotation Specified torque: 27 ~ 35 N·m
{2.8 ~ 3.6 kgf·m}

P-VRZR- 267

- 95 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 99/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Nuts (3) (9) Tighten the bracket nuts.

Specified torque: 34 ~ 39 N·m
{3.5 ~ 4.0 kgf·m}

P-VRZR- 268

(10) Mark the timing mark on the injection pump

Timing mark and the bracket.
Advice
Erase the previous mark.

P-VRZR- 269

FBB plate (11) Loosen the bolt preventing drive shaft

Boltshaft
preventing drive
rotation rotation, install the FBB plate and fix the
FBB plate by tightening the bolt preventing
drive shaft rotation.
Specified torque: 10 ~ 15 N·m
{1.0 ~ 1.5 kgf·m}
(12) Turn the test oil switch OFF.

P-VRZR- 270

Service tools for pump adjustment Adjustment display

Status I tem Measured / input value Unit Specification Tolerance Pump information
(13) Measure T on the pump test bench and
N 0 r/min
Specifiedpartno.

Pump part no.

Pump serial no.

44-6613

44-3062 input the value.

0880052496
(13) T 0.0 deg C GE serial no. 50620-088-52056
Note:
Engine model VRZ_4M41
Ua-ist V Rotation

Pump cylinders
Right
4 cylinders
U α ist is displayed automatically.
Q 0.0 mm3/st
(14) Confirm that the Step status field is green.
ECU MELCO

Mode Adjustment

DQ 0.0 mm3/st Pump type VRZ (12V)

(15) Proceed to the next step.

05/04/03 13:44:46
Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty

(14) Step status Present step

Comment
31 Q_characteristics

Second timing
0r/min 2.91v 0.00mv 60Hz 100%

Next
(15) Sequence 31 / 31
 _ 
After values are input, push Next button.
Select
Adjustment finished

P-VRZR- 376

- 96 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 100/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

(5) Printing the adjustment results and

MC-02 TESTER
Adjustment result saving the test record
Specifiedpartno. 44-6613 Pump serial no. 0880052496
(1) Click the ‘Next’ key.
Test complete Adjustmentnecessary
Pump part no. 44-3062 GE serial no. 50620-088-52056
ECU values Measured values
No. Result Step name N Uasoll Soll-cor TCVF DTCV N T Uaist Q DQ Pt Qo VTPS TA TPS TF

(2) ‘Do you want to print and save test record’

r/min V mv Hz % r/min DegC V mm/st mm/st MPa I/h V mm V V
1 Warm-up 300 2.80 0.00 60 100 0 0.0 0.00 0.0
2 Warm-up 1000 2.91 0.00 60 100 0 0.0 0.00 0.0
3 P-cham_ADJ 1000 2.91 0.00 60 100 0 0.0 0.00 0.000 0.0 0.00
4 Rough-Q_ADJ 1000 2.91 0.00 60 100 0 0.0 0.00 0.0 0.0

is displayed.
5 P-cham_ADJ 1000 2.91 0.00 60 100 0 0.0 0.00 0.000 0.0 0.00
6 Zero_set 500 2.50 0.00 60 0 0 0.0 0.00 0.00 0.00
7 Timer_TA 100 2.41 0.00 60 100 0 0.0 0.00 0.000 0.00 0.00
8 Timer_TA 50 2.41 0.00 60 100 0 0.0 0.00 0.000 0.00 0.00
9 Timer_TA 325 1.53 0.00 60 0 0 0.0 0.00 0.000 0.00 0.00
10 375 1.53 0.00 60 0 0 0.0 0.00 0.000 0.00 0.00

(3) Click ‘OK.’

Timer_TA
11 Timer_TA 375 1.53 0.00 60 100 0 0.0 0.00 0.000 0.00 0.00
12 Timer_TA 500 1.53 0.00 60 100 0 0.0 0.00 0.000 0.00 0.00
13 Timer_TA 1000 2.91 0.00 60 100 0 0.0
Doyou wanttoprint 0.00 record?
andsavetest 0.000 0.00 0.00
14 Timer_TA 1000 2.91 0.00 60 100 0 0.0 0.00 0.0 0.000 0.00 0.00
15
16
17
18
Timer_TA
Timer_TA
Q_characteristics
Cor-Q_ADJ
1900
1900
2300
1900
3.73
3.73
0.87
2.91
0.00
0.00
0.00
0.00
60
60
60
60
100 OK 0
100
100
100
0
0
0
0.0Cancel 0.00
0.0
0.0
0.0
0.00
0.00
0.00
0.0
0.0
0.0
0.0
0.0
0.0
0.000
0.000
0.00
0.00
0.00
0.00
Note:
19 Cor-Q_ADJ 1900 3.73 0.00 60 100 0 0.0 0.00 0.0 0.0
20
21
22
23
Cor-Q_ADJ
Cor-Q_ADJ
Cor-Q_ADJ
Cor-Q_ADJ
1000
1000
600
600
1.53
2.91
1.53
2.20
0.00
0.00
0.00
0.00
60
60
60
60
100
100
100
100
0
0
0
0
0.0
0.0
0.0
0.0
0.00
0.00
0.00
0.00
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
If you select ’Cancel,’ you cannot continue to
24 Cor-Q_ADJ 600 1.86 0.00 60 100 0 0.0 0.00 0.0 0.0
25
26
27
28
Cor-Q_ADJ
Cor-Q_ADJ
Cor-Q_ADJ
Cor-Q_ADJ
600
375
325
100
1.53
1.86
1.86
2.41
0.00
0.00
0.00
0.00
60
60
60
60
100
100
100
100
0
0
0
0
0.0
0.0
0.0
0.0
0.00
0.00
0.00
0.00
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
the next step.
If no further measurements are required, select Next button.
To repeat a measurement, select Repeat button and input step number.
Next
Advice
Step number Repeat

• The printed test record can be given to

(1) P-VRZR- 377
the customer.
• The saved test record is a record of all
the data and must be handled carefully.
(4) Turn the controller unit’s sub-switch OFF.

(5) Turn the controller unit’s main switch OFF.

Adjusting device
(6) Injection pump removal
(1) Remove the adjusting device from the
injection pump’s drive gear.

P-VRZR- 271

CPV (2) Replace cylinder B’s pipe assembly with the

CPV. At this time, replace the gasket with a
new one.

Pipe assembly P-VRZR- 272

- 97 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 101/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

Main harness (3) Disconnect the main harness and the

Plug intermediate harness from the injection
pump.
(4) Remove the test oil hose and the overflow
valve plugs from the injection pump.

Intermediate harness Test oil hose P-VRZR- 273

Torx bolts (4) (5) Install the Q adjustment ROM to the pump
housing.
Note:
Removing the inlet adapter facilitates
installation.
(6) Tighten the Q adjustment ROM’s torx bolts.
Specified torque: 2 ~ 3 N·m
Q adjustment
{0.2 ~ 0.3 kgf·m}
ROM Pump housing Tool name Part no Remarks
Bit
Holder 157915-9820
Holder Bit 157915-9301 T20
P-VRZR- 393

(7) Connect the overflow valve’s bypass hose

Overflow valve to the injection pump.
Bypass hose (8) Tighten the overflow valves using a torque
wrench.
Specified torque: 20 ~ 29 N·m
{2 ~ 3 kgf·m}

Overflow
valve

P-VRZR- 274

(9) Remove the injection pump from the test

Stand
bench.
Injection pump

P-VRZR- 275

- 98 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 102/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

(10) Remove the stand from the pump test

bench.

Stand

P-VRZR- 276

9. MANUAL OPERATION
(SECOND TIMING ADJUSTMENT)
Note:
Preparation (Injection pump disassembly, Drive
gear installation and Injection pump installation)
is the same as that described on pages 93 to
96 for automatic adjustment of second timing.

[1] Second timing adjustment

(1) Turn the controller unit’s sub-switch ON.
(2) Supply test oil to the injection pump at the
Sub-switch specified pressure of 20 kPa {0.2 kgf/cm 2}.

P-VRZR- 397

(3) Select ‘Manual operation’ on the menu

MC-02 TESTER

Copyright(C) 2001-2003 by Bosch Automotive Systems Corporation

display.
Service tools for pump adjustment Version1.0 RBAJ

ROM COVEC-F MITSUBISHI 12V

Inspection/adjustment

VRZ MITSUBISHI 12V

Inspection/adjustment

ROM COVEC-F MAZDA 12V

Inspection/adjustment

(3) Manual operation

Workshop name registration

Exit

P-VRZR- 346

- 99 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 103/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

ADJUSTMENT

(4) Select the ECU (a black point appears when

MC-02 TESTER

ECU reader data

Manual operation the ECU is selected).
Item Value Unit Item Value Unit (5) Press ‘Initialize ECU’ after selecting the
GE Vist V TPS Vist V
ECU.
Item Value Unit Item Value Unit
(6) Press the ‘GE soll’ button and input ‘2.91’
TF deg C Np r/min

(4) Select ECU

into the field. Press the keyboard’s ‘Enter’
ROM COVEC-F MITSUBISHI 12V VRZ MITSUBISHI 12V ROM COVEC-F MAZDA 12V

ECU configuration data

Input
key.
(6) GE Soll V
(7) Press the ‘TCV Duty’ button and input ‘100’
1. Values must be input f or GE soll, TCV Duty and TCV Frequency.
2. Np values do not appear at VRZ pump adjustment.
(7) GE Soll-cor

TCV Duty
mV
%
(8)
(5)
TCV Frequency

Initialize ECU
Hz
into the field. Press the keyboard’s ‘Enter’
Menu key.
P-VRZR- 348
(8) Press the ‘TCV Frequency’ button and input
‘60’ into the field. Press the keyboard’s
Nuts (3)
‘Enter’ key.
Advice
Values must be input for GE soll, TCV Duty
and TCV Frequency.
(9) L o o s e n th e in je c tion p u mp b ra c k e t
installation nuts.

P-VRZR- 264

FBB plate (10) Loosen the bolt preventing drive shaft

Bolt preventing drive rotation and remove the FBB plate.
shaft rotation

P-VRZR- 265

Pipe assembly Adjusting device (11) Insert the lever into the adjusting device
and turn the lever once in the reverse
rotation direction, then turn the lever in the
direction of rotation.
(12) Adjust so that test oil flows from cylinder
B’s pipe assembly at a rate of 1 drop /3
seconds.

P-VRZR- 266

- 100 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 104/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 105/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

INSPECTION

INSPECTION
Inspection sequence
Recording the pump and GE serial numbers  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 103 [1]

Preparation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 103 [2], 104 [3]

Part no. input and installation confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 105 [4]

Warming-up operation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 106 [5]

Pump chamber pressure confirmation

 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 107 [6]

TPS confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 107 [7]

Timer stroke confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 107 [8]

Non-injection confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 108 [9]

Injection quantity confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 108 [10]

Magnet valve operation confirmation  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 109 [11]

Inspection result  ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 

See page 110 [12]

Finish

- 102 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 106/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 107/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

INSPECTION

Fixing stand (8) Reconfirm that the coupling and the fixing
stand bolts and nuts are securely tightened.
(9) Set the 20NP pump tester’s test oil outlet
temperature at 45°C.
(10) Set the cooling unit oil delivery pressure
lever at ‘80 kPa {0.8 kgf/cm2}’ or less.

P-VRZR- 355

FCV (magnet valve) ON/OFF switch (11) Connect the wire harness to the controller
Sub-switch unit’s No 2 ECU connector.
(12) Turn the main switch on the rear of the
controller unit ON.
(13) Set the No 1 ~ No 4 changeover switch at
No 2.
(14) Turn the FCV (magnet valve) ON/OFF
switch ON to energize the magnet valve.
(15) Turn the sub switch on the front of the
ECU for VRZ type controller unit ON.
injection pump
No. 1 ~ No. 4 change-over switch
P-VRZR- 397

[ 3] I nspect i on sof t war e set up:

preparation
(1) Turn the computer and the monitor power
switches ON.

Monitor power switch

Computer power switch

P-VRZR- 210

(2) Start the ‘Service tools for pump adjustment’

software.
MC-02 TESTER (3) Input the password and press the ‘Enter’ key.
Precaution Advice
Password is required to actuate adjustment tools. Input the initial default password ‘RBAJ’ or
Input password and press ENTER key.
your own password.

(3)
P-VRZR- 357

- 104 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 108/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

INSPECTION

[4] P a r t n u m b e r i np u t and
MC-02 TESTER

Copyright(C) 2001-2003 by Bosch Automotive Sys tems Corporation

Service tools for pump adjustment Version1.0 RBAJ
confirmation
ROM COVEC-F MITSUBISHI 12V
(1) Select the ‘VRZ [Mitsubishi 12V] Inspection/ 
Inspection/adjustment

(1) adjustment’ button.

VRZ MITSUBISHI 12V
Inspection/adjustment

ROM COVEC-F MAZDA 12V

Inspection/adjustment

Manual operation

Workshop name registration

Exit

P-VRZR- 346

(2) When the dialog shown at left appears, input

MC-02 TESTER
Part number input the specified part number (6 digits) and
If number input is correct, select Next button.
If you need to input a different number, select Clear button.
press ‘Enter’.
(2) (4)
(3) Input the pump part number (last 6 digits)
and press ‘Enter’.
Specified part no. 446613 Pump serial no. 5555555555
(6 digits) (10 digits)

(3)
Pump part no.
(last 6 digits)
443062 GE serial no.
(13 digits)
6666666666666 (5)
System specifications 1. Specified part no. (4) Input the pump serial number (10 digits) and
Engine model VRZ_4M41 Pump Pump
OEM
Specified part no.

press ‘Enter’.
part no. type Adjustment Inspection
Rotation Right 104700-304* 003040 008040
104700-305* COVEC-F 003051 008051
Pump cylinders 4 cylinders 104700-306* MITSUBISHI 003060 008060
ECU MELCO 109144-305*
109144-306*
VRZ

104700-055* COVEC-F MAZDA

44-6613 44-8813

000550 008550
(5) Input the GE’s serial number (13 digits) and
press ‘Enter’.
2. Pump part no.
Example:
Full pump no. Input pump part no.
Mode Inspection 109144-3052 443052
104700-0551 000551

(6)
(6) Press the ‘Next’ key.
Menu Clear Next

P-VRZR- 378

(7) Confirm that the screen changes to the

MC-02 TESTER

Installationconfirmation
Setup confirmation injection system piping display.
Click on appropriate item Key no. Part name Part no. Note
and explanatory illustration is displayed. 1 Injection pipe 157808-4720
2 Nozzle & nozzle holder assembly 1 688 901 035
1. Injection system piping 3 Same as VP44
Joint
4 Injection tube
2. Overflow piping

3. Adjustment controller wiring

4. Operation sequence 3

2 4

If necessary to proceed
after confirmation, push Next button.
1
Menu

Back Next

P-VRZR- 359

- 105 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 109/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

INSPECTION

Service tools for pump adjustment Adjustment display

[5] Warming-up operation
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

44-8813

44-3052
(1) Set the pump test bench delivery pressure
at the specified 40 kPa {0.4 kgf/cm2}.
Pump serial no. 5555555555
T 0.0 deg C GE serial no. 66666-666-66666
(4) VRZ_4M41

(2) Confirm that the sequence is Step 01/26.

Engine model

Ua-ist V Rotation Right

Pump cylinders 4 cylinders

Q 0.0 mm3/st ECU

Mode
MELCO

Adjustment
(3) Run the injection pump at the specified
Pump type VRZ (12V)
speed N (see figure at left).
02/04/03 14:07:56 (4) Measure N, T and Q on the pump test bench
Menu Part number input

Step information
Present step
No. S tep name N Soll Soll-cor Frequency Duty
and input the values.
(5) Step status 01 Warm-up 300r/min 2.80v 0.00mv 60Hz 100%

Next
Comment Check for fuel leaks.
Note:
(6) Sequence

U α ist is displayed automatically.

01 / 26 After values are input, push Next button.
Select 02 Warm-up 1000r/min 2.91v 0.00mv 60Hz 100%

(2)
(5) Confirm that the Step status field is green.
P-VRZR- 379
(6) Proceed to the next step.
Advice
If U α ist values are not as specified, press
the ‘Next’ button several times. Then, return
to Step the
01/26 using theand
back arrow.that U α
Repeat Step 01/26 confirm
ist values are as specified.
Note:
If not as specified after confirming U α ist several
times, the GE may be faulty.

Service tools for pump adjustment Adjustment display

(7) Confirm that the sequence is Step 02/26.
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

44-8813

44-3052
(8) Run the injection pump at the specified
T 0.0 deg C
Pump serial no.

GE serial no.
5555555555
66666-666-66666
speed N (see figure at left).
(9)
Ua-ist V
Engine model

Rotation
VRZ_4M41
Right
(9) Measure N, T and Q on the pump test bench
4 cylinders

and input the values.

Pump cylinders

Q 0.0 mm /st 3 ECU MELCO

Mode Adjustment
Pump type VRZ (12V)
Note:
02/04/03 14:09:35
U α ist is displayed automatically.
Step information
No. S tep name N Soll
Menu

Soll-cor
Part number input

Frequency Duty
(10) Confirm injection.
(11) Confirm that no fuel leaks from the
Step status Present step 02 Warm-up 1000r/min 2.91v 0.00mv 60Hz 100%
(13) Comment Warm-up
Next
(14) Sequence

Select
02 / 26

03
After values are input, push Next button.
P-cham_ADJ 1000r/min 2.91v 0.00mv 60Hz 100%
injection pump fuel piping connections.
(7) P-VRZR- 380 CAUTION
If there are any fuel leaks, if there is no
injection or if any unusual noises occur
during operation, stop test bench operation
immediately and inspect the pump.
(12) Confirm that the injection pump is
operating normally.
(13) Confirm that the Step status field is green.
(14) Proceed to the next step.
Advice
Because the test oil temperature takes
longer to increase in cold weather, turn the
pump test bench on earlier.

- 106 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 110/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

INSPECTION

Service tools for pump adjustment Adjustment display

[6]Pump chamber pressure
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

Pump serial no.

44-8813

44-3052
confirmation
5555555555
T 0.0 deg C GE serial no. 66666-666-66666
(1) Confirm that the sequence is Step 03/26.
(3) Engine model VRZ_4M41
Ua-ist V Rotation

Pump cylinders
Right
4 cylinders
(2) Run the injection pump at the specified
Pt 0.000 MPa ECU

Mode
MELCO

Adjustment speed N (see figure at left).

Qo 0.0 I/h Pump type

(3) Measure N, T, Pt and Qo on the pump test

VRZ (12V)

TF V
Menu
02/04/03 14:10:05
Part number input
bench and input the values.
Step information
Present step
No. S tep name N Soll Soll-cor Frequency Duty Note:
(5) Step status 03 P-cham_ADJ 1000r/min 2.91v 0.00mv 60Hz 100%

(6) Next
Comment

Sequence
Reconfirm PT standard point.

03 / 26
U α ist and Tf are displayed automatically.
After values are input, push Next button.
Select 04 Zero_set 500r/min 2.50v 0.00mv 60Hz 100% (4) Confirm the pump chamber pressure.
(1) P-VRZR- 386
(5) Confirm that the Step status field is green.
(6) Proceed to the next step.
Service tools for pump adjustment Adjustment display
[7] TPS confirmation
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

44-6613

44-3062
(1) Confirm that the sequence is Step 04/26.
(3)
T 0.0 deg C
Pump serial no.

GE serial no.
0880052496
50620-088-52056 (2) Run the injection pump at the specified
speed N (see figure at left).
Engine model VRZ_4M41
Ua-ist V Rotation Right
Pump cylinders 4 cylinders

VTPS V ECU

Mode
MELCO

Adjustment
(3) Measure N and T on the pump test bench
TPS V Pump type VRZ (12V)
and input the values.
(4) 05/04/03 14:10:51
Note:
Zero set
U α ist, VTPS and TPS are displayed
Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Present step
(5) Step status
Comment
04 Zero_set

Push Zero set button.

500r/min 2.50v 0.00mv 60Hz 0%

automatically.
Next
(6)
(4) Press the ‘Zero set’ key and confirm that the
Sequence 04 / 26
After values are input, push Next button.
Select 05 Timer_TA 100r/min 2.41v 0.00mv 60Hz 0%

(1)
VTPS value is within the specifications.
P-VRZR- 387
(5) Confirm that the Step status field is green.
(6) Proceed to the next step.

Service tools for pump adjustment Adjustment display

[8] Timer stroke confirmation
Status I tem

N
Measured / input value

0 r/min
Unit Specification Tolerance Pump information
Specifiedpartno.

Pump part no.

44-6613

44-3062
(1) Confirm that the sequence is Step 05/26.
T 0.0 deg C
Pump serial no.

GE serial no.
0880052496
50620-088-52056
(2) Run the injection pump at the specified
(3)
Ua-ist V
Engine model

Rotation
VRZ_4M41
Right
speed N (see figure at left).
4 cylinders

(3) Measure N, T and Pt on the pump test bench

Pump cylinders

Pt 0.000 MPa ECU MELCO

Mode Adjustment

VTPS V Pump type VRZ (12V)

and input the values.
TA mm
05/04/03 14:11:50
Note:
Step information
No. S tep name N Soll
Menu

Soll-cor
Part number input

Frequency Duty
U α is t, V T P S a n d T A a re d is p la y e d
automatically.
Step status Present step 05 Timer_TA 100r/min 2.41v 0.00mv 60Hz 100%
(5) Comment 100r/min
Next
(6) Sequence 05 / 26 After values are input, push Next button.
Select

(4) Confirm that the timer stroke TA is within

06 Timer_TA 50r/min 2.41v 0.00mv 60Hz 100%

(1)
the specifications.
P-VRZR- 388
(5) Confirm that the Step status field is green.
(6) Proceed to the next step.

- 107 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 111/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

INSPECTION

Service tools for pump adjustment Adjustment display

Confirm 50 revolutions (Step 06/26) ~ 1,900
Status Item

N
Measured / input value

0 r/min
Unit Specification Tolerance Pump information
Specifiedpartno. 44-6613 revolutions (Step 14/26) using the same
Pump part no. 44-3062

T 0.0 deg C
Pump serial no.

GE serial no.
0880052496
50620-088-52056
procedure used for 100 revolutions (Step 5/26)
Ua-ist V
Engine model

Rotation
VRZ_4M41
Right
above.
Pump cylinders 4 cylinders

Pt 0.000 MPa ECU MELCO

Mode Adjustment
VTPS V Pump type VRZ (12V)

TA mm
05/04/03 14:11:50
Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Step status Present step 05 Timer_TA 100r/min 2.41v 0.00mv 60Hz 100%
Comment 100r/min
Next
Sequence 05 / 26 After values are input, push Next button.
Select 06 Timer_TA 50r/min 2.41v 0.00mv 60Hz 100%

P-VRZR- 381

Service tools for pump adjustment Adjustment display

[9] Non-injection confirmation
Status I tem

N
Measured / input value

0 r/min
Unit Specification Tolerance Pump information
Specifiedpartno.

Pump part no.

44-8813

44-3052
(1) Confirm that the sequence is Step 15/26.
T 0.0 deg C
Pump serial no.

GE serial no.
5555555555
66666-666-66666
(2) Run the injection pump at the specified
(3) Ua-ist V
Engine model

Rotation
VRZ_4M41
Right speed N (see figure at left).
4 cylinders

(3) Measure N, T, Q and DQ on the pump test

Pump cylinders

Q 0.0 mm3/st ECU MELCO

Mode Adjustment

DQ 0.0 mm3/st Pump type VRZ (12V)

bench and input the values.
02/04/03 14:13:11
Note:
Step information
No. S tep name N Soll
Menu

Soll-cor
Part number input

Frequency Duty
U α ist is displayed automatically.
(4) (4) Confirm that the Step status field is green.
Step status Present step 15 Q_characteristics 2300r/min 0.87v 0.00mv 60Hz 100%
Comment Confirm no nozzle injection.

(5) Next
Sequence

Select 16
15 / 26 After values are input, push Next button.
Cor-Q_INSP 1000r/min 2.91v -34.18mv 60Hz 100%
(5) Proceed to the next step.
(1) P-VRZR- 382

Service tools for pump adjustment Adjustment display

[10] Injection quantity confirmation
Status I tem Measured / input value Unit Specification Tolerance Pump information
N 0 r/min
Specifiedpartno.

Pump part no.

44-8813

44-3052
(1) Confirm that the sequence is Step 16/26.
(2) Run the injection pump at the specified
Pump serial no. 5555555555

T 0.0 deg C GE serial no. 66666-666-66666

speed N (see figure at left).

Engine model VRZ_4M41

(3) Ua-ist V Rotation Right

Pump cylinders 4 cylinders

Q 0.0 mm3/st ECU

Mode
MELCO

Adjustment
(3) Measure N, T, Q and DQ on the pump test
DQ 0.0 mm3/st Pump type VRZ (12V)
bench and input the values.
02/04/03 14:13:47 Note:
Part number input

U α ist is displayed automatically.

Menu

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Step status Present step Cor-Q_INSP
(4) Comment
16
Correction point 8
1000r/min 2.91v -34.18mv 60Hz 100%

Advice
Next
(5) Sequence

Do not perform injection quantity

16 / 26
After values are input, push Next button.
Select 17 Cor-Q_INSP 1900r/min 3.73v 34.18mv 60Hz 100%

(1) adjustment.
P-VRZR- 383

(4) Confirm that

(5) Proceed thenext
to the Stepstep.
status field is green.
Service tools for pump adjustment Adjustment display
Status I tem Measured / input value Unit Specification Tolerance Pump information
Specifiedpartno. 44-8813
N 0 r/min Pump part no.

Pump serial no.

44-3052
5555555555 Confirm compensation point 11 (Step 17/26) ~
T 0.0 deg C GE serial no. 66666-666-66666

Ua-ist
Engine model VRZ_4M41 compensation point 1 (Step 25/26) using the
V Rotation Right

Q 0.0 mm3/st
Pump cylinders

ECU
4 cylinders
MELCO
same procedure used for compensation point
DQ 0.0 mm3/st
Mode

Pump type
Adjustment

VRZ (12V)
10 (Step 16/26) above.
02/04/03 14:13:47
Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty
Step status Present step 16 Cor-Q_INSP 1000r/min 2.91v -34.18mv 60Hz 100%
Comment Correction point 8
Next
Sequence 16 / 26 After values are input, push Next button.
Select 17 Cor-Q_INSP 1900r/min 3.73v 34.18mv 60Hz 100%

P-VRZR- 383

- 108 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 112/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

INSPECTION

Service tools for pump adjustment Adjustment display

Status I tem Measured / input value Unit Specification Tolerance Pump information
[11] M a g n e t v a l v e ope rat ion
confirmation
Specifiedpartno. 44-8813
N 0 r/min Pump part no. 44-3052
Pump serial no. 5555555555

(3)
T 0.0 deg C GE serial no.

Engine model
66666-666-66666

VRZ_4M41
(1) Confirm that the sequence is Step 26/26.
Ua-ist V Rotation

Pump cylinders
Right
4 cylinders (2) Run the injection pump at the specified
Q 0.0 mm3/st ECU MELCO

Mode

Pump type
Adjustment

VRZ (12V)
speed N (see figure at left).
(3) Measure N, T and Q on the pump test bench
Menu
02/04/03 14:14:59
Part number input
and input the values.
Step information
Step status Present step
No.
26 Stop_Q
S tep name N
1000r/min
Soll
2.91v
Soll-cor
0.00mv
Frequency
60Hz
Duty
100%
Note:
Comment

U α ist is displayed automatically.

Confirm no nozzle injection when the FCV is OFF.
Next
Sequence 26 / 26
After values are input, push Next button.
Select  _ 
Inspection finished

(1) P-VRZR- 384

FCV (magnet valve) ON/OFF switch (4) Turn the FCV (magnet valve) ON/OFF
switch OFF and confirm that non-injection
results.
Advice
To confirm non-injection from the nozzle,
look at the monitor screen and confirm that
non-injection occurs within a short time (6 ~
7 seconds).

P-VRZR- 356

Service tools for pump adjustment Adjustment display

(5) Measure N, T and Q on the pump test bench
Status I tem Measured / input value Unit Specification Tolerance Pump information

N 0 r/min
Specifiedpartno.

Pump part no.

44-8813

44-3052
and input the values.
T 0.0 deg C
Pump serial no.

GE serial no.
5555555555
66666-666-66666
(6) Confirm that the Step status field is green.
(5)
Ua-ist V
Engine model

Rotation
VRZ_4M41
Right
(7) Proceed to the next step.
Pump cylinders 4 cylinders

Q 0.0 mm /st 3 ECU MELCO

Mode Adjustment
Pump type VRZ (12V)

02/04/03 14:14:59
Menu Part number input

Step information
No. S tep name N Soll Soll-cor Frequency Duty

(6) Step status Present step

Comment
26 Stop_Q

Confirm no nozzle injection when the FCV is OFF.

1000r/min 2.91v 0.00mv 60Hz 100%

Next
(7) Sequence 26 / 26
After values are input, push Next button.
Select  _ 
Inspection finished

P-VRZR- 384

- 109 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 113/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

INSPECTION

MC-02 TESTER
[12] Inspection result
Specifiedpartno. 44-8813
Inspection result
Pump serial no. 5555555555 Test complete Adjustmentnecessary
(1) Click the ‘Next’ key.
44-3052 66666-666-66666
(2) The message ‘Do you want to print and save
Pump part no. GE serial no.

ECU values Measured values

No. Result Step name N Uasoll Soll-cor TCVF DTCV N T Uaist Q DQ Pt Qo VTPS TA TPS TF
r/min V mv Hz % r/min DegC v mm/st mm/st MPa I/h v mm V V

test record’ appears.

1 Warm-up 300 2.80 0.00 60 100 0 0.0 2.80 0.0
2 Warm-up 1000 2.91 0.00 60 100 0 0.0 2.90 0.0
3 P-cham_ADJ 1000 2.91 0.00 60 100 0 0.0 2.91 0.000 0.0 0.00
4 Zero_set 500 2.50 0.00 60 0 0 0.0 2.50 0.78 0.78
5 Timer_TA 100 2.41 0.00 60 100 0 0.0 2.41 0.000 0.78 2.80

(3) Click ‘OK.’

6 Timer_TA 50 2.41 0.00 60 100 0 0.0 2.41 0.000 0.78 2.80
7 Timer_TA 325 1.53 0.00 60 0 0 0.0 0.00 0.000 0.00 0.00
8 Timer_TA 375 1.53 0.00 60 100 0 0.0 0.00 0.000 0.00 0.00
9 Timer_TA 375 1.53 0.00 60 100 0 0.0 1.52 0.000 0.78 2.80
10 Timer_TA 500 1.53 0.00 60 0 0 0.0 1.52 0.000 0.78 2.80
11
12
13
14
Timer_TA
Timer_TA
Timer_TA
Timer_TA
1000
1000
1900
1900
2.91
2.91
3.73
3.73
0.00
0.00
0.00
0.00
60
60
60
60
100
100
100
100
0
0
0
0
0.0
0.0
0.0
Doyou wanttoprint
0.0
0.00
0.00
0.00
andsavetest
0.00
record?
0.0
0.000
0.000
0.000
0.000
0.77
0.78
0.76
0.76
2.76
2.80
2.72
2.72
Note:
15 Q_characteristics 2300 0.87 0.00 60 100 OK 0 0.0Cancel 0.00 0.0 0.0
16
17
18
19
Cor-Q_INSP
Cor-Q_INSP
Cor-Q_INSP
Cor-Q_INSP
1000
1900
2300
600
2.91 -34.18
3.73 34.18
1.93 -14.65
2.20 58.59
60
60
60
60
100
100
100
100
0
0
0
0
0.0
0.0
0.0
0.0
0.00
3.76
1.91
2.26
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
If you select ’Cancel,’ you cannot continue to
20 Cor-Q_INSP 600 1.86 -43.95 60 100 0 0.0 2.26 0.0 0.0
21
22
23
24
Cor-Q_INSP
Cor-Q_INSP
Cor-Q_INSP
Cor-Q_INSP
375
375
325
325
1.86 -63.48
1.53 -63.48
1.86 -53.71
1.53 -63.71
60
60
60
60
100
100
100
100
0
0
0
0
0.0
0.0
0.0
0.0
0.00
0.00
0.00
0.00
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
the next step.
25 Cor-Q_INSP 100 2.41 136.72 60 100 0 0.0 2.54 0.0 0.0
26
27
28
Stop_Q 1000 2.91 0.00 60 100 0 0.0 2.90 0.0
Advice
If no further measurements are required, select Next button.
To repeat a measurement, select Repeat button and input step number.
Step number Repeat
Next • The printed test record can be given to
(1)
the customer.
P-VRZR- 385
• The saved test record is a record of all
the data and must be handled carefully.
(4) Turn the controller unit’s sub-switch OFF.
(5) Turn the controller unit’s main switch OFF.

- 110 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 114/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

TIGHTENING TORQUES

Units: N·m {kgf·m}

P-VRZR- 389

- 111 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 115/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

PART NUMBER EXPLANATION

1. INJECTION PUMP ASSEMBLY NUMBER

1 0 9 1 * * - * * * *
(1) (2) (3) (4) (5) (6)
(1): VRZ type injection pump
(2): Number of cylinders
0 spare 1 spare 2 spare
3 3 cylinders 4 4 cylinders 5 5 cylinders
6 6 cylinders 7 spare 8 spare
9 master pump
(3): Number of plungers - diameter
0 2 - φ6.5 1 2 - φ7 2 2 - φ7.5
3 2 - φ8 4 2 - φ8.5 5 2 - φ9
6 spare 7 spare 8 spare
9 spare
(4): Engine manufacturer
0 Mazda 1 Isuzu 2 Nissan (Motor)
3 Mitsubishi (Motors) 4 Nissan (Diesel), Komatsu, others 5 spare
6 spare 7 spare 8 spare
9 spare
(5): Proper number
Design sequence starting from ‘00’ with each change in the first seven digits.

(6): Suffix

2. BOSCH TYPE NUMBER

NP - VRZ - *  /  ** E **** R NP * * *
(1) (2) (3) (4) (5) (6) (7) (8)

(1): Manufactured by Bosch Automotive Systems Corporation

(2): VRZ type injection pump
(3): Number of cylinders
(4): Plunger diameter
(5): Electronic governor
(6): Maximum controlled governor speed (r/min)
(7): Direction of pump rotation
R: clockwise viewed from drive side
L: counter clockwise viewed from drive side
(8): Proper number

- 112 -
http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 116/117
7/22/2019 Bomba VE VRZ EE14E-11162 VRZ Service Manual

http://slidepdf.com/reader/full/bomba-ve-vrz-ee14e-11162-vrz-service-manual 117/117