Pneumatic

Timers and Counters

Kuhnke’s wide selection of Counters and Timers provide easy solutions for constructing
pneumatic logic systems. Counters are available with 4 to 8 digit readouts, panel or
base mounting with several options to suit the application. Five versions of pneumatic
timers with ranges from .1 second to 100 hours with a variety of valve and mounting
options provide the most complete product line available in the industry.

Counters are constructed with durable molded bodies. White digits on black background
make units easy to read. Units are available with or without manual resets and a variety
of options. A special type allows the counter to be reset by a pneumatic pulse in
addition to a manual reset button. A predetermining counter includes an output valve to
stop production when the count is reached.

Timers depending on design, are constructed of molded bodies usually with aluminum
bases to provide sturdy fitting connection points. Timers are available in on delay or off
delay versions and incorporate a 3/2 or 5/2 output valve.

Typical timing circuits are included in the catalogue section to assist in designing easy
installations.
Counters and Timers
Series 50 Counters Kuhnke System Logic Devices

Panel Mounted Pneumatic Counter

50670
The pneumatic counter can be used as an event, part or
lot counter. The counter registers pneumatic impulses on
a 6 digit display. Totalizer operates with impulse pressure
between 2 and 8 bar. The counter can be reset either
manually via a reset button, or by a pneumatic signal to a
specially provided port.

Technical Specifications

Op. Pressure: Media: Weight:

2-8 bar Filtered air 7 grams
Connections: Control Connections: Materials:
M5 ports Port Z - Counter pulse input Molded body
Display: Port Y - Reset Dimensions:
Black with white Duty Cycle: Face plate: 60mm W x 50mm H
digits (6 numbers) Continuous Behind panel: 62mm Deep x
Reset: Min. pulse duration 8 ms 50mm Wide x 26mm High
Manual button on cover or Min. pause 10 ms Panel Cut Out:
pneumatic signal of 180 ms Operating Ambient: 52mm Wide x 28mm High
duration. 0ºC to + 60ºC 2 mounting holes required.
Hardware included

6
 Counters and Timers
Kuhnke System Logic Devices Series 50 Counters

Panel Mounted Pneumatic Predetermining Counter

50680
Counter is used for selecting the number of desired
operations on a production run. The number of
operations is set on the lower scale by holding down a
white button and setting the count to be reached. The
upper scale is a 5 digit totalizer. When the count reaches
the lower scale setting, a built-in 3/2 valve is switched to
provide a pneumatic output to stop machine or signal that
the count has been reached. Valve remains switched
until counter is reset.

The counter operates with an impulse pressure between

2 and 8 bar and can be reset either manually via a reset
button or by a pneumatic signal to a specially provided
port.

Technical Specifications
Op. Pressure: Control Connections: Materials:
2-8 bar. Port Z - Counter pulse input Molded body
Connection: Port Y - Reset Dimensions:
M5 ports Port P - Supply air to 3 way valve Face plate: 60mm W x 75mm H
Display: Port A - Output signal from valve Behind panel: 62.5mm Deep x
Black with white digits Duty Cycle: 51mm Wide x 50mm High
(5 numbers) Continuous Panel Cut Out:
Reset: Min. pulse duration 8 ms 52mm Square
Manual button on cover or Min. pause 10 ms 2 mounting holes required.
pneumatic signal of Operating Ambient: Hardware included.
180 ms duration. 0ºC to +60ºC
Media: Weight:
Filtered air 12 grams

7
Counters and Timers
PM Counters Kuhnke System Logic Devices

Panel or Base Mounted Pneumatic Counters

These pneumatic totalizers can be used as an event, part or lot

counter. The counter registers pneumatic impulses on 4, 6 or 8 digit
displays. Standard units operate with impulse pressures between 1.5
and 6.5 bar. Low pressure models operate between 0.5 and 2 bar. A
variety of options include panel mounting with screws or mounting
clips and surface mount with base or rear stud. The counters are
available with or without manual reset.

Catalogue Number
Standard Clip Mounting Description Panel Mounted Surface Mounted
Standard Screw With Stud
Clip Mtg. Fastening Base Mounting
4 Digit PM14-21 PM14-11 APM14-01 PM14-01
With
Manual 6 Digit PM16-21 PM16-11 APM16-01 PM16-01
Reset
8 Digit Not Available Not Available Not Available Not Available

4 Digit PM14-20 PM14-10 APM14-00 PM14-00

Without
Manual 6 Digit PM16-20 PM16-10 APM16-00 PM16-00
Reset
8 Digit PM18-20 PM18-10 APM18-00 PM18-00

Options
For Low pressure version (0.5 to 2 bar) add an “L” prefix to the
Base catalogue number.
Base Mount
Mount
A manual reset guard can be added to help prevent accidental
resetting of the counter. Add suffix “V” to the catalogue number.
For a spade key reset add suffix “VS” to the catalogue number.
For a secret reset add an “S” suffix.
Standard designs have 10-32 NPT ports.

Technical Specifications
Op. Pressure: Duty Cycle: Dimensions (approx.):
1.5 to 6.5 Bar Std. Continuous 4 Digit – 22mm H x 33mm W x 66mm D.
0.5 to 2 bar Low Press. Min. pulse duration 8 ms 6,8 Digit – 22mm H x 50mm W x 66mm D.
Connections: Min. pause 10 ms For Screw mtg. add 1” to H dim.
10-32 port, Option 1/8. Operating Ambient: For base mtg. add 1 “ to D dim.
Display: 0ºC to + 60ºC
Black with white digits Weight: Panel Cut Out:
Reset: 7 to 13 grams 4 Digit – 22mm H x 32mm W
With or without manual reset. Materials: 6,8 Digit – 22mm H x 47mm W
Molded body, steel frame.
Media:
Filtered air

8
 Counters and Timers
Kuhnke System Logic Devices Series 51 Mini Timer

Miniature Panel Mounted Timer

(Up to 5 minutes)

2 to 30 Seconds 51020-03
20 to 300 Seconds 51020-30

The Mini-timer is an adjustable panel mounted time delay

device (normally closed valve). Timing is set by adjusting the
front dial. The timer is equipped with 2 vertical scales that
indicate the set time and the time remaining in the cycle
(countdown time).

To begin the timing operation, air pressure is applied to port

one. When the set time is reached the internal valve is
switched over to provide an output at port 2. The valve
remains open until the input air is switched off. Removing the
air supply at any time resets the timer.

The mini timer is constructed of a molded body with a clear

plastic lens for viewing the scales. Ports, M5 are located on
the rear of the unit. The timer is panel mounted with a built in
retaining clip.
Accessories
A molded bezel (catalogue no. 51025) can be added to the
panel to provide screw fastening of the timer for easy
removal. The bezel cutout size is 52 x 52mm and the bezel
dimensions are 60mm wide x 75mm high.

A rear mounting bracket, (catalogue

no. 51031) can be used to mount
the timer in the rear of the panel or
on a DIN rail as required. The
bracket has built-in connections for
side M5 porting.

Rear Mounting

Technical Specifications
Op. Pressure: Reset: Operating Ambient:
2 to 6 bar By removal line pressure 0ºC to 60ºC
Connections: Reset Time: Dimensions (inches):
M5 200 ms 24mm W x 48mm H x 68mm D.
Media: Repeatability: Panel Cutout:
Filtered, dry air. ± 0.3 Sec. 51020-03 20mm W x 45mm H.
Non-lubricated ± 3 Sec. 51020-30 Mounting:
Operating Valve: Time Setting: Retaining Clip.
3/2 (NC) - internal exhaust Via adjustment knob.
Orifice size - 1mm Setting Accuracy:
Flow @ 6 bar – 40 litre ± 0.6 Sec. 51020-03
Timing Start: ± 6 Sec. 51020-30
Application of line Materials:
pressure to port 1. Molded housing.

9
Counters and Timers
Series 51 Timers Kuhnke System Logic Devices

Rear Mounted - Set-it, Forget-it Timer

(Up to 3 minutes)
The Series 51 timer is an adjustable precise time delay
control device. The timer is available with either an on
delay- (NC) or off delay- (NO) 3/2 built-in valve. It is
designed for mounting along with valves or other logic
devices and is available with M5 bottom ports, or 1/8 side
ports. Bottom ported timers can also be panel mounted
using (2) threaded M3 inserts on the top cover.

Timing operation can be set up in 2/2; either via direct

connection of the pressure line to be timed (1/8 ported
only) or via a separate pilot signal. When pressure is
applied to the input (or pilot port) the timing sequence
begins by setting a vacuum within the timer. Using
atmospheric pressure (independent of line pressure), the
timer begins the preset timing cycle. At the end of the
Side Ported 1/8
cycle an internal 3/2 valve is switched providing an
output. The timer resets automatically after removal of
the control signal.

Bottom Ported
M5

Technical Specifications
Op. Pressure: Reset: Materials:
1.5 to 8 bar By removal of pilot (or Line) Polyamide housing, aluminum
Connections: signal –independent of whether base, Buna N seals.
M5 (10-32) or the time interval has elapsed or not. Operating Ambient:
1/8 ports Reset Time: -10ºC to 60ºC
Media: 200 ms Dimensions (mm):
Filtered air, non lubricated. Repeatability: M5 port 1/8 port
Operating Valve: ± 2% of selected time. Height 92 105
3/2 - internal exhaust Time Setting: Width 36 36
Orifice size - 2mm Via adjustment knob. Length 70 70
Flow @ 6 bar – 200 liters Operation: Weight 35 gr. 45 gr.
Timing Start: Timing cycle uses atmospheric
Application of pilot (or Line) pressure drawn into vacuum. Mounting:
pressure to control port. Air Consumption: Via 4 holes in base.
During timing cycle only -3 l/m

10
 Counters and Timers
Kuhnke System Logic Devices Series 51 Timers

Selection Chart
Diagrams Catalogue Number
Timing Range
1/8 Side M5 Bottom
ported Ported
.5 to 60
Seconds
51006-00US 51006-00
On Delay Off Delay On
(Normally Closed) (Normally Open) 1 to 120
Delay 51012-00US 51012-00
Seconds
(NC)
1 to 180
Seconds
51018-00US 51018-00
Connections .5 to 60
Seconds
51006-01US 51006-01
Off
1/8 Side Ported Timers Delay 1 to 120
Seconds
51012-01US 51012-01
Side ported timers are supplied with a 10/32 port plug (NO)
1 to 180
to set up preferred connections. Seconds
51018-01US 51018-01

For a separate (isolated) pilot

signal, insert a 10-32 plug into Port Identification
the internal port (inside port 12
or 10). Use loctite or equal to 12 - Control input signal (NC version).
seal the port. Then connect a 10 - Control input signal (NO version).
Separate Pilot separate pilot input signal at
Signal
1 – Air supply.
port 12 (10). 2 – Valve output.
For using the same source as
the supply for the output valve
and pilot signal, plug port 12 Power Connections
(10) using a 1/8 plug and
connect the switched air supply For installations requiring larger output valves, use the
Supply and Pilot to port 1. Discard the 10-32 standard timer and connect a pneumatically operated
Same Source plug. single air piloted 3/2 or 5/2 valve of the size required to
the timer output. Contact factory with size
10-32 (M5) Bottom Ported Timers requirements.

Timer is supplied only with separate (isolated) Typical Circuits

control input signal port. Connections are located on
the underside of the timer base. See typical timing circuit diagrams at the end of the
timer catalogue section for help in constructing
The bottom ported timer can be panel mounted pneumatic timer circuits.
using (2) M3 threaded inserts on the top cover.

Control input signal must be at the same pressure as system line pressure.

11
Counters and Timers
PMT Timers Kuhnke System Logic Devices

Panel or Subplate Mounted Pneumatic Timer

(Up to 3 Minutes)

The Type PMT timer is an adjustable precise time delay

control device. The timer is available with an on delay
(NC) output.

Timing operation is dependent upon the input of a

separate control signal which starts the timing sequence
by setting a vacuum within the timer. Using atmospheric
pressure (independent of line pressure), the timer begins
the preset timing cycle. At the end of the cycle an internal
3/2 valve is switched providing an output. The timer
resets automatically after removal of the control signal.

The PMT has a separate subplate enabling the unit to be

supplied with 10-32 or 1/8 porting. The timer can be
panel mounted with a bezel, or in the rear on a sub plate.

Panel Mounted PMT

timer with SPA1B
subplate

Technical Specifications
Op. Pressure: Reset: Materials:
1 to 6.5 bar. Automatic by removal of Acetal and polycarbonate
Connections: pilot signal. enclosure. Diaphragms-
10-32 or 1/8 ports Reset Time: Buna N
via bottom sub plate 60 ms @ 3 bar Operating Ambient:
Control Pressure: Repeatability: OºC to 65ºC
(A) Low Press. – 1 to 6.5 bar ± 3% of selected time. Dimensions (mm):
(B) Standard – 2 to 6.5 bar Time Setting: (including sub plate)
Media: Via adjustment knob. Height – 55
Filtered air or non-aggressive Accuracy ±10% Width – 38
gas, non-lubricated. Operation: Depth – 108
Timing Valve: Timing cycle uses Mounting:
atmospheric pressure Via sub plate (2 holes) or if
Flow @ 6.5 bar –0.3 liters drawn into vacuum. Panel mounted, through a
Dial Indicator: Air Consumption: 38mm square cutout.
Displays set time. 0.3 l/m @ 6.5 bar 2 mounting holes required,
Timing Start: hardware included.
Application of pilot pressure
to control port.

12
 Counters and Timers
Kuhnke System Logic Devices PMT Timers

Selection Chart

Catalogue Number
Timing Range
Subplate Panel Mount Panel Mount
Mounting Vertical Bezel Horizontal Bezel
0.3 to 3 Seconds PMT1D1B3 PMT1D2B3 PMT1D3B2

1 to 10 Seconds PMT1E1B3 PMT1E2B3 PMT1E3B2

3 to 30 Seconds PMT1F1B3 PMT1F2B3 PMT1F3B2

6 to 60 Seconds PMT1G1B3 PMT1G2B3 PMT1G3B2

12 to 120 Seconds PMT1H1B3 PMT1H2B3 PMT1H3B2

18 to 180 Seconds PMT1J1B3 PMT1J2B3 PMT1J3B2

Diagram Low Pressure Version

The PMT standard control input pressure range is 2 to
6.5 bar. For a low pressure pilot actuator (1 bar min.),
change the “B” in the catalogue number to “A”.

Subplate Mounting Position

Standard timers are supplied with the subplate
Port Identification mounting position at the bottom of the timer. For
mounting the subplate in another position, change the
6 - Control input signal. last digit of the catalog number as follows: 1 for top; 2
1 – Air supply. for right side; 3 for bottom; 4 for left side.
2 – Valve output.
Power Connections
Subplate (Required)
For installations requiring larger output valves, use the
The PMT, whether panel or base mounted, requires a standard timer and connect a pneumatically operated
subplate for connecting fittings and air lines. Several single air piloted 3/2 or 5/2 valve of the size required to
types are available to suit connection needs. The the timer output. Contact factory with size
subplate is supplied loose and unmounted, as a requirements.
separate item.
Typical Circuits
Catalogue Number
Port Location See typical timing circuit diagrams at the end of the
10-32 Ports 1/8 NPT
timer catalogue section for help in constructing
pneumatic timer circuits.
3 Bottom ports SPAIA SPA2A

6 Side ports SPA1B SPA2B

6 Side and 3
SPA1C SPA2C
Bottom ports

13
Counters and Timers
PT Timers Kuhnke System Logic Devices

Panel or Rear Mounted Pneumatic Timer

(Up to 60 Minutes)
The PT timer is an adjustable precise time delay
pneumatic device. The timer is available with an on delay
(NC), or an off delay (NO) output. The timer has 1/8 NPT
ports.

The PT series timer combines a pneumatic timing

mechanism with a floating spool valve assembly to
provide a wide range of adjustable time control for fluid
power systems. The timing assembly, which operates
independently of the control pressure, is available in nine
different ranges from one tenth of a second to 60
minutes, adjustable by means of a time-calibrated dial.
Timing action is initiated by a motor diaphragm operated
by a control pressure of from 0.5 to 10 bar.

The timer is equipped with a multi purpose 3/2 output

valve allowing it to be used as normally open, normally
closed or as a diverter.

The PT is designed for panel or surface mounting. Panel

mounted versions include a 88mm square bezel while
surface mounted units are equipped with a bracket for
Surface Mounted vertical mounting. If required, The PT can be specially
PT Timer calibrated for mounting horizontally.

Technical Specifications
Op. Pressure Reset: Operating Ambient:
0.5 to 10 bar.I On Delay - Removal of pilot -30ºC to 70ºC
Connections: pressure from control port. Dimensions (mm):
1/8” NPT ports Off Delay - Application of pilot Height – 134
Control Pressure: pressure to control port. Width – 63 -
0.5 to 10 bar Reset Time: Depth – 63
Media: 60 ms @ 3.5 bar Mounting:
Filtered air or non-aggressive Repeatability: Surface or panel mounted.
gas, non-lubricated. Up to 200 sec. - ± 5%. Drilling Plan (panel mount):
Output Valve: Over 200 sec. - ± 10%. 81 dia. hole.
Time Setting:
Flow @ 6.5 bar – 250 liters Via dial.
Multi purpose 3/2 spool. Accuracy ±10% of full scale.
Dial Indicator: Operation:
Displays set time. Timing cycle uses
Timing Start: atmospheric pressure.
On Delay - Application of pilot Materials:
pressure to control port. Zamak housing, polycarbonate
Off Delay - Removal of pilot knob, aluminum valve with stainless
pressure to control port. spool. Diaphragms - Buna N

14
 Counters and Timers
Kuhnke System Logic Devices PT Timers

Selection Chart

Catalogue Number
Timing Standard Vertical
Panel Mounted
Range Surface Mount
On Off On Off
Delay Delay Delay Delay
0.1 to 1 Second PT31A PT41A PT35A PT45A

0.5 to 5 Seconds PT31B PT41B PT35B PT45B

1.5 to 15 Seconds PT31C PT41C PT35C PT45C

5 to 50 Seconds PT31D PT41D PT35D PT45D

20 to 200 Seconds PT31E PT41E PT35E PT45E

1 to 300 Seconds PT31K PT41K PT35K PT45K

1 to 10 Minutes PT31F PT41F PT35F PT45F

3 to 30 Minutes PT31H PT41H PT35H PT45H

6 to 60 Minutes PT31I PT41I PT35I PT45I

Diagrams Options
Surface mounted units are calibrated for mounting in
the vertical position. If horizontal mounting is required,
add suffix “Y1” to the catalogue number. For a
stainless steel fitting mounted on the pilot port add
On Delay Off Delay suffix “SS”. To include a Dial Stop set at the factory
(which prevents settings above or below a given
Port Identification number) add suffix ”DS” and specify setting. For a
Tamper Proof Cover add suffix “TP” to the catalogue
Port C - Control input signal number.
1 - System air supply
2 - Valve output Power Connections
3 - Exhaust
For installations requiring larger output valves, use the
On Delay Timer Operation standard timer and connect a pneumatically operated
Pilot pressure is applied to the control port to start single air piloted 3/2or 5/2 valve of the size required to
timing. After the timer reaches its set time, the valve the timer output. Contact factory with size
switches over. Removal of the pilot signal at any time requirements.
resets the timer.
Typical Circuits
Off Delay Timer Operation
Applying pilot pressure of at least 100ms in duration to See typical timing circuit diagrams at the end of the
the control port shifts the valve. When the pilot timer catalogue section for help in constructing
pressure is removed, the timing sequence begins. pneumatic timer circuits.
After the timer reaches its set time, the valve switches
off. Re-applying the pilot pressure resets the timer and
valve.

15
Counters and Timers
Series 54 Timers Kuhnke System Logic Devices

Panel Mounted Pneumatic Timer

(Up to 100 Hours)
The 54 Series timer is a totally pneumatic device with +/-
1% repeatability. Timing is fully adjustable throughout the
timing range by a knob on the front dial face. The
standard timer is equipped with a special 5/2 valve which
provides for on or off delay timing (depending on
plumbing connections). The front dial displays set time
and the time remaining in the cycle.

The operation of the timer depends on the input of a

separate control signal. The control signal drives a
regulated air motor and gear chain to provide accurate
timing regardless of control air pressure fluctuation. The
timer resets automatically (approx. 200ms) after removal
of control pressure signal.

A special version of the timer includes a rotor stop option

which allows for an external valve to be added to permit a
“count down on hold” function.

The 54 Series timer is self-contained in a panel mounted

lexan case with a front timing adjustment knob.
Connections are made at the rear of the timer. Spring
clips are used to panel mount the unit.

Technical Specifications
Op. Pressure: Time Setting: Timing Sequence:
0-10 bar Via front dial knob. Adjustable On delay or off delay
Control Pressure: throughout timing range depending on valve
1.5 to 10 bar Accuracy of Setting: connections.
non-lubricated air ± 2%
Output Valve: Repeatability: Operating Ambient:
5/2 ± 1% of end scale value. 0ºC to 60ºC
Flow – 200 liters @ 6.5 bar Operation: Materials:
Orifice size - 2mm Independent regulated air Lexan case, cast aluminum
motor. Air consumption 10 l/m rear housing, nylon, brass, and
Connection: Output air piloted 5 way valve. stainless alloy mechanism.
M5 ports Reset: Dimensions (mm):
Media: Automatic - by removal of Faceplate –72 square Behind
Filtered air or gas. control pressure. panel –112 D x 66 H x 66 W.
Non-lubricated. Reset Time: Panel Cutout:
Indicators: 200 ms. 66mm square
Displays set time and time Mounting:
remaining before valve Spring clips.
actuation.

16
 Counters and Timers
Kuhnke System Logic Devices Series 54 Timers

Selection Chart
Timing Sequence
Catalogue Number
Timing Range
Standard With Rotor
Timer Stop Option
0.3 to 10 Seconds 54021 54050

3 to 100 Seconds 54022 54051

0.3 to 10 Minutes 54023 54052

3 to 100 Minutes 54024 54053

0.3 to 10 Hours 54025 54054

3 to 100 Hours 54026 54055

tД= Selected time delay. tЕ= Total duration of cycle.

Rotor Stop Option (Countdown on Hold)

Diagrams
A rotor stop option is available to override the timing
action or to hold the timer valve in its switched position
after the timer has completed its cycle, and signal
pressure is removed. Option provides 2 additional rear
ports connected via tube, which allows valves or other
On Delay Off Delay logic devices to be spliced into the internal circuit
Blocked Port 2 Blocked Port 4 between the pilot signal regulator and rotor assembly.

For holding timer valve in its switched position or to

Timer output valve is 5/2, with M5 connections. Valves place "timing on hold”, an external 3/2 valve (NO) can
are supplied from factory blocked with a cap nut (port be used to block the flow to the air motor (connected
4) for 3/2 off delay. For on delay, move cap nut to port between rotor stop ports 1-2). If timing on hold is
2. For full 5/2 operation remove nut. desired, the pilot signal must remain on throughout the
entire cycle.
Port Identification Power Connections
Port 12 - Control input signal (on timer body). For installations requiring larger valves, use the
Valve - standard timer and connect a pneumatically operated
1 - System air supply single air piloted 3/2 or 5/2 valve of the size required to
2 - Valve output "off delay connection" the timer output. Contact factory with size
3 - Exhaust for port 2 requirements.
4 - Valve output "on delay connection"
5 - Exhaust for port 4
Typical Circuits
See typical timing circuit diagrams at the end of the
Replacement Parts timer catalogue section for help in constructing
Control port input filter 72754500-00 pneumatic timer circuits.
Output valve 54530

17
Counters and Timers
Typical Timing Circuits Kuhnke System Logic Devices

Timing Using a Manual Push-Pull Valve

Push-Pull valve can be used to start and stop
To Device
system manually while providing timing to the
circuit. A 5/2 valve can also be used when
operating a double acting cylinder, or for
alternating outputs.
Timer
Output Operation

Push-Pull Pushing in knob starts air flowing to device

Knob with
Pneumatic ‫ڒ‬ Typical Timer and to timer. When the timer reaches set
time, it sends a signal to the reset port of the
Reset Port Air Timer On Delay
Supply Control push-pull valve shutting down the air output.
Port To stop the process, pull the knob out,
shutting off the air and resetting the timer.
‫ڒ‬ Typical Item Selection
To Timer
Air Supply
Control Port
(Connection depends Any on delay timer (Consider length of time
on timer used.)
required and mounting preference).
Push-Pull Valve- Cat. nos. 76022-27-22 (3/2,
1/8 ports), 76023-27-42 (5 way, 1/8) or
76043-27-42 (5/2, 1/4).
5/2 Push Pull Knob Valve Alternative- Lever operated valve, pneumatic
When using a 5/2 valve note output reset, contact factory for information.
connections. All other connections same
as 3/2.

Converting an On Delay timer output to an Off Delay output

To Device On delay timer signals can be converted to
an off delay signal with the use of an
interposing normally open 3/2 air piloted
Normally Open valve.
3/2 Air Piloted
Valve Operation

Air pressure is applied to the timer and to the

operating device through the 3/2 piloted
valve. When the timer reaches set time, it’s
output switches the air piloted valve shutting
‫ڒ‬ off the air to the device. Removing the air
signal from the timer resets the air piloted
Air Supply valve and air flows again to the device.

Typical On Typical Item Selection

Delay Timer
Any on delay timer (Consider length of time
required and mounting preference).
3/2 air piloted valve (NO) Cat. no. 76036-71-
‫ڒ‬ Air
Supply
31 (1/8). For larger valves contact factory for
information.

18
 Counters and Timers
Kuhnke System Logic Devices Typical Timing Circuits

Timing Using a Momentary Start Signal

To Device Timer
Control
Port
Typical Timer
Pushbutton Valve On Delay
3/2
(or other valve with Timer
momentary output signal Output
shorter than set time
delay). ‫ڒ‬
Double Air Air Supply
(Connection depends
Piloted Valve
3/2 ‫ڒ‬ on timer used.)
Air Supply
‫ڒ‬
Air Supply

A timing sequence can be established from a momentary

To Timer pressure signal using an interposing pneumatically operated
Control Port valve. The most common signal used is from a pushbutton, but
inputs from limit switches, foot pedals or other devices can be
used to initiate timing. The size of the air piloted valve determines
the air volume output.

Operation
5/2 Double Air Pilot Valve
A 5/2 double air pilot valve can be substituted when
Pressing the pushbutton sends a signal to switch the air piloted
operating a double acting cylinder or for dual valve on. The valve output is connected to the device to be
alternate outputs. Note output connections. All other controlled and to the timer control port. When the timer reaches
connections same as the 3/2 diagram. it’s set time it sends a signal back to the air pilot valve resetting it,
turning off the output to the device. The timer resets.

From output Typical Item Selection

of timer
Pushbutton
Valve - 3/2 Any on delay timer (consider length of time required and
mounting preference).
Pushbutton 3/2 (choice of colour)- Cat. nos. 76022-62-21 (Red), -
OR
Logic 23 (Black) or -24 (Green).
Valve Double air piloted valve 3/2- Cat. no. 76022-71-22 (1/8 Ports).
‫ڒ‬ To port 10 of
For larger sizes of double air piloted valves use a 5/2 valve and
plug port 2 for 3/2 operation. Connect device and timer control to
Air pilot valve port 4 of 5/2 valve. Use Cat. nos. 76047-81-42 for 1/4 ports or
76067-81-42 for 1/2 ports.
Optional Stop Button
A stop pushbutton can be added to the circuit if
required. The stop button resets the air piloted valve.
The start signal must be off to avoid conflicting
signals at the air piloted valve.

19
Counters and Timers
Typical Timing Circuits Kuhnke System Logic Devices

Continuous Cycling Timer Circuit

Timer # 2 Timer # 1
On Delay On Delay

Output A

Output B
(if required)

To port 12 (14)
of air pilot valve
Double Air
Piloted Valve
5/2.

‫ڒ‬
Air Supply

Continuous cycling is accomplished by the use of 2 timers operating a double To port 2 (4)
air piloted valve. Off and on times are dependent on the type and set time of of air pilot
valve
timers used. The size of the air piloted valve determines the air volume output.
The position of the air piloted valve determines the start up of the timing Series 54 Timer Connections
sequence. If the timing sequence must be restarted in a specific order, a reset Timer diagrams shown are 3/2types.
circuit must be added at port 12 of the air piloted valve to move it to the start 54 Series timers have a 5/2 valve
output with an isolated pilot port.
position prior to resuming operation.

Operation
Air supply to From output
System pressure is turned on. Air flows through port 2 of the pilot valve to drive pilot valve of Timer 2
timer #1 and the device being controlled. When timer 1 reaches set time, it
sends a signal to port 14 of the pilot valve, switching the air output to port 4,
starting the timing sequence on timer #2 and shutting down timer 1 and the
output to the device being controlled. When timer 2 reaches set time, a signal is OR
Logic
sent to port 12 of the piloted valve resetting it and restarting the cycle. Valve

Typical Item Selection

Toggle
Timers- Any on delay timer. (Consider length of time required and mounting Lever
preference.) Valve
To port 12 of Air
‫ڒ‬
(Maint.
Double Air Piloted Valve- Cat. nos. 81014 (M5 ports), 76027-71-42 (1/8), Pos.)
Pilot Valve
76047-81-42 (1/4), or 76067-81-42 (1/2).

Optional On-Off Valve with

Reset Circuit

20
 Counters and Timers
Kuhnke System Logic Devices Typical Timing Circuits

Continuous Cycling Timer Circuit Using PT Timers

Continuous cycling is accomplished by the use of
2 timers operating a spring return air piloted
valve. Off and on times are dependent on the To Device
time range of the timers used. The size of the air Timer # 1
PT31 On Delay
piloted valve determines the air volume output.

Operation

System pressure is turned on. Air flows through

port 2 of Timer #2 to drive timer #1 and to
Air piloted
operate the air pilot valve turning on air to the Valve, Spring
device being controlled. When timer 1 reaches
‫ڒ‬
Return
set time, it sends a signal to port C of timer 2,
shutting down the air supply to the air piloted Air Supply
valve and timer 1. This enables timer 2 to begin Timer # 2
timing. When timer 2 reaches set time, it PT41 Off Delay
operates and the cycle is repeated. Removing ‫ڒ‬
the air supply resets the circuit to the start
Air Supply
position.

Typical Item Selection

One On Delay PT timer and one Off Delay PT

timer with the required time ranges.
Single air piloted, spring return valve, 3/2, cat. no.
76026-71-21 (1/8), 76046-71-21 (1/4), 76066-81-
21 (1/2). For operating double acting cylinders
use 5/3 valves.

Using a Momentary Start Signal with an Off Delay PT 41 or PT45 Timer

One shot timing can be initiated from a
momentary air signal using a PT41 or PT45 off To Device
delay timer.

Operation Pushbutton Valve

3/2
A momentary pilot pressure applied to the control (or other valve with
port from a pushbutton or similar device switches momentary output
signal )
the timer valve and provides an output. Releasing
the button starts the timing cycle. When the set Timer
time is reached, the valve operates, shutting PT41 or PT45
down the output to the device being controlled. ‫ڒ‬
Typical Item Selection ‫ڒ‬ Air Supply
(note port 3
connection)
Any PT41 or PT45 timer. Air Supply
Pushbutton catalogue number 76022-62-21
(Red) or other valve with a momentary output
signal.

21
Counters and Timers
Typical Timing Circuits Kuhnke System Logic Devices

Timing using Start-Stop Pushbuttons

To Device

Timer
Control
Port
Typical Timer
On Delay

Stop
Timer
Output
‫ڒ‬
Button Air Supply
3/2 (Connection
OR depends on
Logic timer used.)
Valve

Double Air

‫ڒ‬
Piloted Valve
3/2

Start
Button
3/2

‫ڒ‬
Air Supply

‫ڒ‬
Separate start-stop pushbuttons can be used in conjunction with a To Timer
double air piloted valve and an “or” logic valve to control a timing Control Port
circuit if required. A wide selection of types and colours of
pushbuttons is available to meet design requirements. The size of
the air piloted valve determines the air volume output.

Operation

Pressing the start pushbutton sends a signal to switch the air piloted
valve on. The valve output is connected to the device to be controlled 5 Way Double Air Pilot Valve
and to the timer control port. When the timer reaches it’s set time it A 5 way double air pilot valve can be substituted
when operating a double acting cylinder or for
sends a signal back to the air pilot valve resetting it, turning off the alternating outputs. Note output connections. All
output to the device. To stop the timing (ie. emergency stop) press other connections same as the 3/2 diagram.
the stop button, which sends a signal via the “or” logic valve to reset
the double air piloted valve.

Typical Item Selection

Any on delay timer (consider length of time required and mounting preference).
Pushbutton 3/2 (choice of colour)- Cat. nos. 76022-62-21 (Red), -23 (Black) or -24 (Green).
Double air piloted valve 3/2- Cat. no. 76022-71-22 (1/8 Ports).
For larger sizes of double air piloted valves use a 5/2 valve and plug port 2 for 3/2 operation. Connect device and
timer control to port 4 of 5/2 valve. Use Cat. nos. 76047-81-42 for 1/4 ports or 76067-81-42 for 1/2 ports.
Logic valve-“OR” cat. no. 47003.

22