M54/M74HC257

M54/M74HC258
HC257 QUAD 2 CHANNEL MULTIPLEXER (3-STATE)
HC258 QUAD 2 CHANNEL MULTIPLEXER (3-STATE, INVERTING)

. HIGH SPEED

. tPD = 10 ns (TYP.) at VCC = 5 V

LOW POWER DISSIPATION

. ICC = 4 µA (MAX.) at TA = 25 °C
HIGH NOISE IMMUNITY

. VNIH = VNIL = 28 % VCC (MIN.)

OUTPUT DRIVE CAPABILITY B1R F1R

. 15 LSTTL LOADS
SYMMETRICAL OUTPUT IMPEDANCE
(Plastic Package) (Ceramic Package)

. IOH = IOL = 6 mA (MIN.)

BALANCED PROPAGATION DELAYS

. tPLH = tPHL
WIDE OPERATING VOLTAGE RANGE M1R C1R

. VCC (OPR) = 2 V to 6 V
PIN AND FUNCTION COMPATIBLE
WITH 54/74LS257/258
(Micro Package)
ORDER CODES :
M54HCXXXF1R
(Chip Carrier)

M74HCXXXM1R
M74HCXXXB1R M74HCXXXC1R

PIN CONNECTIONS (top view)

HC257

DESCRIPTION
The M54/74HC257 and the M54/74HC258 are high
speed CMOS MULTIPLEXERs fabricated with sili-
2
con gate C MOS technology.
They have the same high speed performance of
LSTTL combined with true CMOS low power con-
sumption.
HC258
These IC’s are composed of an independent 2-
channel multiplexer with common SELECT and EN-
ABLE INPUT.
The M54/74HC258 is an inverting multiplexer while
the M54/74HC257 is a non-inverting multiplexer.
When the ENABLE INPUT is held ”High”, outputs of
both IC’s become high-impedance state. If SELECT
INPUT is held ”Low”, ”A” data is selected, when SE-
LECT INPUT is high ”H”, ”B” data is chosen.
All inputs are equipped with protection circuits
against static discharge and transient excess volt-
age.

October 1992 1/12

M54/M74HC257/258

INPUT AND OUTPUT EQUIVALENT CIRCUIT

CHIP CARRIER

HC257 HC258

NC = No Internal Connection

PIN DESCRIPTION (HC257) PIN DESCRIPTION (HC258)

PIN No SYMBOL NAME AND FUNCTION PIN No SYMBOL NAME AND FUNCTION
1 SELECT Common Data Select 1 SELECT Common Data Select
Input Input
2, 5, 14, 11 1A to 4A Data Input From Source A 2, 5, 14, 11 1A to 4A Data Input From Source A
3, 6, 13, 10 1B to 4B Data Inputs from Source B 3, 6, 13, 10 1B to 4B Data Inputs from Source B
4, 7, 12, 9 1Y to 4Y 3 State Multiplexer 4, 7, 12, 9 1Y to 4Y 3 State Multiplexer
Outputs Outputs
15 OE 3 State Output Enable 15 OE 3 State Output Enable
Inputs (Active LOW) Inputs (Active LOW)
8 GND Ground (0V) 8 GND Ground (0V)
16 V CC Positive Supply Voltage 16 VCC Positive Supply Voltage

2/12
 M54/M74HC257/258

IEC LOGIC SYMBOL

HC257 HC258

LOGIC DIAGRAM

HC257 HC258

TRUTH TABLE

INPUTS OUTPUTS
OE SELECT A B Y (257) Y (258)
H X X X Z Z
L L L X L H
L L H X H L
L H X L L H
L H X H H L
X = DON’T CARE Z = HIGH IMPEDANCE

3/12
M54/M74HC257/258

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
VCC Supply Voltage -0.5 to +7 V
VI DC Input Voltage -0.5 to VCC + 0.5 V
VO DC Output Voltage -0.5 to VCC + 0.5 V
IIK DC Input Diode Current ± 20 mA
IOK DC Output Diode Current ± 20 mA
IO DC Output Source Sink Current Per Output Pin ± 35 mA
ICC or IGND DC VCC or Ground Current ± 70 mA
PD Power Dissipation 500 (*) mW
o
Tstg Storage Temperature -65 to +150 C
o
TL Lead Temperature (10 sec) 300 C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Value Unit
VCC Supply Voltage 2 to 6 V
VI Input Voltage 0 to VCC V
VO Output Voltage 0 to VCC V
o
Top Operating Temperature: M54HC Series -55 to +125 C
o
M74HC Series -40 to +85 C
tr, tf Input Rise and Fall Time VCC = 2 V 0 to 1000 ns
VCC = 4.5 V 0 to 500
VCC = 6 V 0 to 400

4/12
 M54/M74HC257/258

DC SPECIFICATIONS
Test Conditions Value
Symbol Parameter TA = 25 oC -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
VIH High Level Input 2.0 1.5 1.5 1.5
Voltage 4.5 3.15 3.15 3.15 V
6.0 4.2 4.2 4.2
V IL Low Level Input 2.0 0.5 0.5 0.5
Voltage 4.5 1.35 1.35 1.35 V
6.0 1.8 1.8 1.8
V OH High Level 2.0 1.9 2.0 1.9 1.9
VI =
Output Voltage 4.5 IO=-20 µA 4.4 4.5 4.4 4.4
VIH
V
6.0 or 5.9 6.0 5.9 5.9
4.5 V IL IO=-6.0 mA 4.18 4.31 4.13 4.10
6.0 IO=-7.8 mA 5.68 5.8 5.63 5.60
VOL Low Level Output 2.0 0.0 0.1 0.1 0.1
VI =
Voltage 4.5 IO= 20 µA 0.0 0.1 0.1 0.1
VIH
V
6.0 or 0.0 0.1 0.1 0.1
4.5 V IL IO= 6.0 mA 0.17 0.26 0.33 0.40
6.0 IO= 7.8 mA 0.18 0.26 0.33 0.40
II Input Leakage VI = VCC or GND ±0.1 ±1 ±1 µA
6.0
Current
IOZ Output Leakage VI = VIH or VIL ±0.5 ±5 ±10 µA
6.0
Current VO = VCC or GND
ICC Quiescent Supply 6.0 VI = VCC or GND 4 40 80 µA
Current

5/12
M54/M74HC257/258

AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)

Test Conditions Value
o
Symbol Parameter TA = 25 C -40 to 85 oC -55 to 125 oC Unit
VCC CL
54HC and 74HC 74HC 54HC
(V) (pF)
Min. Typ. Max. Min. Max. Min. Max.
tTLH Output Transition 2.0 25 60 75 90
tTHL Time 4.5 50 7 12 15 19 ns
6.0 6 10 13 15
tPLH Propagation 2.0 45 100 125 150
tPHL Delay Time 4.5 50 13 20 25 30 ns
(A, B - Y)
6.0 11 17 21 26
2.0 62 140 175 210
4.5 150 18 28 35 42 ns
6.0 15 24 30 36
tPLH Propagation 2.0 45 100 125 150
tPHL Delay Time 4.5 50 13 20 25 30 ns
(SELECT - Y)
6.0 11 17 21 26
2.0 62 140 175 210
4.5 150 18 28 35 42 ns
6.0 15 24 30 36
tPZL Output Enable 2.0 40 110 140 165
tPZH Time 4.5 50 RL = 1 KΩ 12 22 28 33 ns
6.0 10 19 24 28
2.0 57 150 190 225
4.5 150 RL = 1 KΩ 17 30 38 45 ns
6.0 14 26 32 38
tPLZ Output Disable 2.0 28 140 175 210
tPHZ Time 4.5 50 RL = 1 KΩ 14 28 35 42 ns
6.0 13 24 30 36
CIN Input Capacitance 5 10 10 10 pF
COUT Output 10
pF
Capacitance
CPD (*) Power Dissipation 47
pF
Capacitance
(*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC/4 (per Channel)

6/12
 M54/M74HC257/258

SWITCHING CHARACTERISTICS TEST WAVEFORM

TEST CIRCUIT ICC (Opr.) C PD CALCULATION

CPD is to be calculated with the following

formula by using the measured value of
ICC (opr.) in the test circuit opposite.
ICC ( opr)
CPD =
fIN × VCC

INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF

SWITCHING CHARACTERSISTICSTESt.

7/12
M54/M74HC257/258

Plastic DIP16 (0.25) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

a1 0.51 0.020

B 0.77 1.65 0.030 0.065

b 0.5 0.020

b1 0.25 0.010

D 20 0.787

E 8.5 0.335

e 2.54 0.100

e3 17.78 0.700

F 7.1 0.280

I 5.1 0.201

L 3.3 0.130

Z 1.27 0.050

P001C

8/12
 M54/M74HC257/258

Ceramic DIP16/1 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 20 0.787

B 7 0.276

D 3.3 0.130

E 0.38 0.015

e3 17.78 0.700

F 2.29 2.79 0.090 0.110

G 0.4 0.55 0.016 0.022

H 1.17 1.52 0.046 0.060

L 0.22 0.31 0.009 0.012

M 0.51 1.27 0.020 0.050

N 10.3 0.406

P 7.8 8.05 0.307 0.317

Q 5.08 0.200

P053D

9/12
M54/M74HC257/258

SO16 (Narrow) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.004 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45° (typ.)
D 9.8 10 0.385 0.393
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 8.89 0.350
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.62 0.024
S 8° (max.)

P013H

10/12
 M54/M74HC257/258

PLCC20 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 9.78 10.03 0.385 0.395

B 8.89 9.04 0.350 0.356

D 4.2 4.57 0.165 0.180

d1 2.54 0.100

d2 0.56 0.022

E 7.37 8.38 0.290 0.330

e 1.27 0.050

e3 5.08 0.200

F 0.38 0.015

G 0.101 0.004

M 1.27 0.050

M1 1.14 0.045

P027A

11/12
M54/M74HC257/258

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.

 1994 SGS-THOMSON Microelectronics - All Rights Reserved

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A

12/12