CONTENTS

QUICK REFERENCE GUIDE

PROGRAMME CHART
PREPARING THE LAUNDRY
SELECTING A PROGRAMME AND OPTIONS
STARTING AND COMPLETING A PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
DAILY MAINTENANCE AND CLEANING

INSTRUCTIONS FOR USE

BOOKLET
BEFORE USING THE DRYER / CONNECTIONS PAGE 11
ELECTRICAL CONNECTION PAGE 12
PRECAUTIONS AND GENERAL
RECOMMENDATIONS PAGE 13

DESCRIPTION OF THE DRYER PAGE 14

DRAINAGE SYSTEM PAGE 15
DOOR REVERSIBILITY / CHILD SAFETY LOCK PAGE 16
HEAT EXCHANGER PAGE 17
TROUBLESHOOTING GUIDE / AFTER-SALES
SERVICE PAGE 18
10

Downloaded from www.Manualslib.com manuals search engine

 BEFORE USING THE DRYER / CONNECTIONS
1. Removing the packaging and check Stability:
• After unpacking, make sure that the dryer is When installing the dryer always carefully level the
undamaged. If in doubt, do not use the dryer. dryer adjusting the four feet and check the correct
Contact After-Sales Service or your local retailer. levelling with a spirit level.
• Keep the packaging materials (plastic bags, To built in the dryer
polystyrene parts, etc.) out of reach of children, as Remove the work-top and replace it with the Built-
they are potentially dangerous. In kit UBS 10 (according to Eec Electrical
• Remove the protective foil from the control panel. Regulations), available at your dealer.
2. Electrical Connections Stacking kit
• Electrical connections must be carried out by a Your dryer can be stacked on top of your front
qualified technician in compliance with the loading washing machine. The type of stacking kit is
manufacturer's instructions and current standard stated in the Instruction for use of your washing
safety regulations. machine or pls. contact your dealer or our After
• Electrical connection must comply with local Sales Service.
Electricity Board regulations.
Minimum housing dimensions:
• Voltage information, power consumption and the
required fuse protection is shown on the rating Width: 600 mm
plate mounted at the rear of the dryer. Height: 850 mm
• The manufacturer cannot accept any liability for Depth: 600 mm
personal injury or damage to property resulting
from failure to adhere to these instructions.
• The dryer must be earthed as prescribed by law.
• Do not use extension leads or multiple adaptors.
• Before any maintenance on the dryer disconnect it
from the mains supply.
• Do not operate the dryer if it has been damaged
during transport. Contact one of our After-Sales
Service technicians.
• Mains cable replacement is only to be carried out by
After-Sales Service.
• After installation access to the mains plug has to be
guaranteed, or the all-pole disconnection has to be
possible with a switch.
3. Installation
• Do not install your dryer where it can be subject to
extreme conditions, such as: poor ventilation,
temperatures around freezing or above 35° C.
• Before running the first cycle ensure the water
container and heat exchanger are correctly
positioned.
• Only for water container top version: if possible use
a hose to drain the water directly into the domestic
plumbing system. This will avoid having to empty
the water container at the end of each drying cycle
since the condensation water can be directly
drained away. See also chapter “Drainage System”.
• Take care not to install the dryer on a deep-pile
carpet.
• Take care not to trap the mains cable between the
dryer and the wall.

11

Downloaded from www.Manualslib.com manuals search engine

 ELECTRICAL CONNECTION
1) For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A 13amp
fused plug, to change a fuse in this type of plug use an A.S.T.A.
approved fuse to BS 1362 type and proceed as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the fuse
cover is lost the plug must not be used until a correct replacement is
fitted.
Correct replacement are identified by the colour insert or the colour
embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical
store.

2) For the Republic of Ireland only

The information given in respect of Great Britain will frequently
apply, but a third type of plug and socket is also used, the
2-pin, side earth type.

3) Socket outlet / plug (valid for both countries)

If the fitted plug is not suitable for your socket outlet, please contact
Whirlpool Service for further instruction. Please do not attempt to
change plug yourself. This procedure needs to be carried out by a
qualified Whirlpool technician in compliance with the manufactures
instructions and current standard safety regulations.

12

Downloaded from www.Manualslib.com manuals search engine

 PRECAUTIONS AND GENERAL
RECOMMENDATIONS
1. Packing
5. General recommendations:
• Always set the programme/time selector knob to
The packing box may be fully recycled as the “0” position after use.This prevents the dryer
confirmed by the recycling symbol . from being switched on accidentally.
• Before cleaning or carrying out maintenance,
2. Energy saving tips switch off the dryer and disconnect it from the
• Always dry a full load: depending on the type of mains supply.
laundry and the programme/drying time. • To clean the outside of the dryer, use a neutral
• By preference use the maximum spin speed allowed detergent and a damp cloth.
by your washing machine, since draining the water • Do not use abrasive detergents.
mechanically requires less energy. You will save time • Wipe away lint from the door seal and the door
and energy when running your drying cycle. using a damp cloth.
• Do not overdry the laundry. • If the lint filter mesh is clogged, clean it with water
• Clean the lint filter after every drying cycle. and a soft brush.
• Place your dryer in a room with a temperature • Since lint can go through the filter it is necessary to
between 15° C and 20° C. In case of higher clean, from time to time, the complete filter area
temperature ventilate the room. (including below the filter) with a brush, a damp
• Always select the correct programme/drying time cloth or with a vacuum cleaner.
for the load in order to obtain the desired drying • If necessary, the power cable may be replaced with
results. an identical one obtained from our After-Sales
• Select the gentle option only with small loads. Service. The power cable must only be replaced by
• When drying cotton, for example. dry iron dry and a qualified technician.
cupboard dry loads together. Start with the iron dry
EC Declaration of Conformity
programme/drying time setting, remove the laundry
to be ironed at the end of that cycle and dry the • This dryer has been designed, constructed and
remainder of the load on the cupboard dry setting. distributed in compliance with the safety
requirements of EC Directives:
3. Disposing of packaging and old Dryer:
The dryer is built from reusable materials. The • 73/23/EEC Low Voltage Directive
dryer must be disposed of in compliance with local • 89/336/EEC EMC Directive
waste disposal regulations. • 93/68/EEC CE Marking Directive.
• Before scrapping, cut off the power cable so that
the dryer cannot be connected to the mains.
4. Child safety:
Children must not be allowed to play with the • The dryer must only be used in the household for
dryer. the prescribed uses.

13

Downloaded from www.Manualslib.com manuals search engine

 DESCRIPTION OF THE DRYER
A. Work top.
B1. Water Container bottom
version or A
B2. Water Container top version.
C. Contact pin.
D. Door: B2
To open the door: pull the
handle. G
To close the door: push gently
until closed. C
E. Filter.
F. Child Safety Lock.
G. Button for heat exchanger flap F
opening. E
H. Heat exchanger. D

B1

Reminder - Maintenance and Cleaning

Clean the lint filter at the end of every drying cycle.

Open the door
Pull the filter upwards
Open the filter
Remove lint using a soft brush or your fingertips
Close the filter
Push the filter back into place.

Heat exchanger

Clean the heat exchanger at least every 3 months (See “HEAT EXCHANGER” chapter).
Wipe away any lint/fluff from the door seal and interior using a damp cloth.

14

Downloaded from www.Manualslib.com manuals search engine

 DRAINAGE SYSTEM
For water container top only B
To avoid having to empty the
water container at the end of
each cycle, the condensation
water can be drained away.

Note: Normally the drain hose is

not supplied; the accessory AMH
883 kit, available at your dealer or
our After Sales Service, should be
used.

The connection for direct

draining is at the rear of the
dryer.
A. Place an absorbent cloth
underneath to collect water
spillage. C
B. Remove the hose located at the
lower rear part of the dryer and
insert it in the nearby hole.
C. Fix the hose (length: 1.5 m) to the
outlet connection. The height
difference between the two
drainage connections should not
exceed 1m.
Notice: To avoid siphoning, the end
of the hose must not be
immersed in the drain water.
Avoid bending and twisting
the hose.

15

Downloaded from www.Manualslib.com manuals search engine

 DOOR REVERSIBILITY / CHILD SAFETY LOCK
Door Reversibility
A. Unplug the dryer. C
B. Open the door.
C. Using a spanner, turn the contact pin in the upper part of the door
by 90° and remove it.

D. Unscrew the 2 screws of the door hinge and remove the door.
E. Removing the door lock:
Unscrew the 2 screws above and below the door lock system.
Lift the door lock from the bottom, sliding it upwards about
1.5 cm, and remove it.
F. Reverse the door:
Fasten the door on the desired side with the 2 screws. C
G. Insert the door lock system on the opposite side of the hinge
fixation and push it down 1.5 cm.
H. Fix the 2 screws above and below the door lock system.
I. Take care not to reverse the sense of the door lock system. The
child safety must be above the locking mechanism.
J. Replace the contact pin in the inside of the door (top).

Child Safety Lock

How to use the child safety lock
1. Open the door.
2. Using a coin or a screwdriver, turn the plastic screw (J) clockwise 90°.
Slot vertical: the door cannot be locked.
Slot horizontal: the door can be locked.

E E

G
E
E

16

Downloaded from www.Manualslib.com manuals search engine

 HEAT EXCHANGER
Before cleaning or carrying out
maintenance, switch off the dryer.

Clean the heat exchanger at least

every three months, proceeding as
follows: A
A. Open the door and press the heat
exchanger flap button on the
bottom of the door entrance.
B. The heat exchanger flap opens.
C. Fold the heat exchanger handle
B
upwards to the horizontal position
and remove the heat exchanger.
D. Clean the heat exchanger under
running water by turning it around
to reach all sides.
E. Wipe away dust and lint from the
seals and the heat exchanger.
F. Remove the lint in the heat
exchanger housing. Keep the
drainage hole (left side in front in
the housing) free from lint.
G. Replace the heat exchanger in its
housing (TOP or HAUT mark C
upwards) and press the handle.
H. Close the flap.

The heat exchanger aluminium plates

may become discoloured over time.

17

Downloaded from www.Manualslib.com manuals search engine

 TROUBLESHOOTING GUIDE / AFTER-SALES
SERVICE
Troubleshooting Guide After-Sales Service

If a fault occurs, before contacting our After- If, after carrying out the above checks the
Sales Service, make the following checks to malfunction persists or appears again, turn
try and remedy the problem: the dryer off and call our After-Sales Service
(refer to guarantee).
Drying takes too long / laundry is not dry enough:
• Was the correct programme selected? Please specify:
• Was the inserted laundry too wet (Washing • The nature of the fault.
machine spin speed less than 800 rpm? When the • The dryer type and model.
spinning speed is less than 800 rpm the water • The service code (the number after the word
container fault may occur during the drying cycle)? Service on the adhesive rating plate) on the
• Is the lint filter dirty (filter indicator lamp on)? right-hand side when the door is open.
• Is the heat exchanger dirty? (refer to the • Your full address and phone number.
Instructions for use)
• Is the ambient temperature too high?
• Does “END” and “Anti-Crease” LED’s are lights
up? - The drying cycle is terminated, the laundry can
be taken out.

The dryer does not operate:

(after a power failure and/or interruption to the
mains supply, always press the Start/Pause
button).
• Is the plug properly inserted into the mains
electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door properly closed?
• Has the programme been selected?
• Has the start delay option been selected?
• Has the Start/Pause button been pressed?
Lint filter or water container indicator lamp
light on:
• Is the lint filter clean?
• Is the water container empty?
• Is the water container correctly positioned?
• Is the heat exchanger clean?
Water droplets underneath the dryer:
• Is the heat exchanger correctly positioned?
• Has any fluff on the heat exchanger seal been wiped
away?
• Has any fluff on the door seal been wiped away?
• Has the water container been positioned correctly?

18

Downloaded from www.Manualslib.com manuals search engine