FRANCE LOADER

Technical Specification
9-900 S-C
2011-07-10

1750

1350
850

200
1320 1530 1430 890
4280

820

36° 1840

3190

1890

APPLICATION BUCKET MOTION TIMES

Sandvik FRANCE LOADER is a true compact and flexible full Diesel Raising time 2.6 sec.
loader for narrow vein mining. Lowering time 1.5 sec.
Tipping time 4.1 sec.
The highest possible rate of productivity is ensured by
fast and easy one pass loading.
Sandvik FRANCE LOADER CTX-1DS WEIGHTS
layout is designed for good visibility and balance. Operating weight 3 650 kg (8 030 lb)
This and the powerful four-wheel-drive articulated Total loaded weight 4 650 kg (10 230 lb)
Chassis ensure fast and safe manoeuvering in tight Shipping weight
spaces. Axle weights without load
All the service points are well protected but easy to Front axle 1 120 kg (2 460 lb)
access. Rear axle 2 530 kg (5 570 lb)
Axle weights with load
Front axle 2 630 kg (5 790 lb)
Rear axle 2 020 kg (4 440 lb)
CAPACITIES
Unit weight is dependent on the selected options.
Tramming capacity 1 000 kg (2 200 lb)
Breakout force, lftt 10.7 kN - 1 094 kg (2 407 lb)
Breakout force, tilt 36.9 kN - 3 766 kg (8 285 lb) DRIVING SPEEDS FORWARD AND REVERSE
Tipping load 2 941 kg (6 470 lb)
Bucket std. 0.54 m³ (0.7 yd³), 500 BNH lip Loaded, max 9 km/h (5.6 mph)

1/4
© 2008 Sandvik Mining and Construction
 FRANCE LOADER
Technical Specification
9-900 S-C
2011-07-10

SERVICE CAPACITIES STEERING

Fuel tank 40 liters (10.5 gal.) Full hydraulic, centre-point articulation, power steering
Hydraulic oil tank 62 liters (16.4 gal.) with two double acting cylinders. Steering controlled by
Hydrostatic transmission oil tank 31 liters (8.2 gal.) stick, interlock protection.
Turning angle ± 36°
FRAME Turning radius inner 1840 mm (72”)
Rear and front frame Welded steel construction outer 3190 mm (125”)
Main components in steering system:
Material E 36.3
Main valve HPI
Central hinge Spherical bearings
Control valve Danfoss
(large angle)
Steering hydraulic cylinders 2 pcs, 60 mm (2.36”),
ENGINE Tamrock
Pressure settings:
Diesel engine Deutz F3L 912W Main relief valve 14.0 Mpa (140 bar)
Output 33 kW (45 hp) / 2 500 rpm Shock load valves 17.5 Mpa (175 bar))
Torque 170 Nm / 1 500 rpm
Number of cylinder In line 3 BUCKET HYDRAULICS
Displacement 2 827 cm³
Cooling system Air cooled Full hydraulic open center system with one gear pump.
Combustion principle 4-stroke, 2-stage combustion The oil flow from steering hydraulic pump is directed to
Electric system 12 V starter and accessories bucket hydraulics when steering is not used.
Air filtering Oil bath air cleaner Equipped with mechanical dual control lever.
Exhaust system Catalytic purifier Lift cylinder 1 pcs, ø100 mm (3.9”)
Tilt cylinder 1 pcs, ø120 mm (4.7”)
TRANSMISSION Pressure setting for:
Main relief valve 14.0 Mpa (140 bar)
Hydrostatic transmission Variable flow
Bucket tilt 6.0 Mpa (60 bar)
fully reversible
Bucket roll-back 18.0 Mpa (180 bar)
One pump Linde, variable displacement
Boom raise 18.0 Mpa (180 bar)
0 to 50 cm³/rev
Boom lower 6.0 Mpa (60 bar)
One motor Linde, fixed 35 cm³/rev
Main components:
Bucket hydraulic cylinders Tamrock
TRANSFER CASE
Control valve Commercial hydraulics
Type Gear Fittings JIC
Location Rear axle
ELECTRICAL EQUIPMENT
AXLES
Alternator 45 A
Front and rear Tamrock, fixed Battery 1 x 12 V, 95 Ah
No-spin in front axle Starter 1.7 kW, 12 V
Central hinge oscillation ± 10° Driving and working lights font, 2 pcs (H1 55 W)
rear, 2 pcs (H1 55 W)
WHEELS
Tires 7.50 x 15
Air pressure, front and rear 3.5 bar (350 kPa) OPTIONAL EQUIPMENT
*) Bucket size 0.5 m³ (0.7 yd³), width 950 mm (37”).
BRAKES
FOPS-ROPS safety canopy.
Dynamic service brake through the hydrostatic Reverse alarm.
transmission. Emergency steering system.
The parking and emergency brake is spring applied, Complete spare wheel.
hydraulically released multidisc oil immersed brakes *) EU, UL, CSA, AUS norms package.
inclosed on the transfer case.
*) replaces standard component

© 2008 Sandvik Mining and Construction 2/4

Technical Specification
9-900 S-C

FRANCE LOADER
2008-07-10

DUMP DATA

1800

1400

1540

42°
1240
620

715

CAGING DIMENSIONS

1350

3570 890
Bucket and canopy removed .......................................... 3 287 kg

1350

3300 890

Bucket, canopy and lift arms removed .......................... 3 107 kg

991

3200 890
Bucket, canopy, lift arms, axles and tires removed...... 2 372 kg

Sandvik Mining and Construction reserves the right to change this specification without further notice.
Sandvik Mining and Construction Lyon S.A.S.
B.P.46 - FR-69881 Meyzieu Cedex, France
Tel. +33 4 7245 2200, Telefax +33 4 7831 7980 4/4
www.sandvik.com
 3/4
MICROSCOOP CTX L - 04D S - A DOC 010

2000 - 12 - 14

GRADE(%)

SANDVIK TAMROCK SECOMA se reserve le droit de modifier sans préavis les caractéristiques techniques de cette notice. aprod1200
Microscoop FRANCE LOADER CTX
Spec. no: L - 04D S - A
2000 - 12 - 14
4/4

TONNES PER HOUR

SANDVIK TAMROCK SECOMA se réserve le droit de modifier sans préavis les caractéristiques SANDVIK TAMROCK SECOMA S.A., B.P. 46 - 69881 Meyzieu Cedex, France
techniques de cette notice.
Tel. int. + 33 4 72 45 22 00, Telex 300526 F
Telefax int. + 33 4 7831 7980
ESPECIFICACIONES TECNICAS SCOOPTRAM FRANCE LOADER CTX- 1DS

 Scooptram , Modelo CTX-1DS, año 2008, de bajo perfil con motor compensado

 Peso: 3.5 toneladas SIN CARGA

 Cuchara: capacidad: 0.5 m3. 0.75 YD3

 MOTOR HIDROSTATICO LINDE

 BOMBA HIDROSTATICA LINDE

 MOTOR DIESEL
Modelo: F3L912 DEUTZ CON TURBO
Potencia: 33 kW (45 hp) / 2 500 rpm
Torque : MAX 170 Nm / 1 500 rpm
 Carga : 1.0T

 Altura de descarga : 1.5 m

 Llantas 7.5 x 15 PLY L5S

 Techo de protección del operador.

 Sistema Eléctrico de 12 voltios

 Sistema hidráulico Piloteado

 Dimensiones:

 Largo : 4.50 m

 Ancho : 0.83 m

 Alto : 1.70 m

 Peso : 4.50 t (CON CARGA)

VELOCIDADES DEL VEHÍCULO – EN CARGA

Delantero o reverso con la resistencia rodante del 3%

Velocidad Km/h 0.0 a 20.00
Velocidad mph 0.0 a 17.00