High Availability With Synology
Uploaded by
Dhani Aristyawan SimangunsongHigh Availability With Synology
Uploaded by
Dhani Aristyawan SimangunsongHOW TO CREATE A HIGH-AVAILABILITY SETUP WITH SYNOLOGY
By Chrisanthi Christodoulou – System Consultant
Introduction
It is always recommended to create a high-availability cluster with two identical Synology NAS
servers. Synology High Availability (SHA) implements two hosts to create a high-availability cluster where
one NAS is the active server and the other is the passive server. A high-availability cluster allows the
continuous replication of data in the active to the passive server. This means that mirrored copies of any
files in your system exist on both hosts, and the passive server takes over all service in case the active server
malfunctions or crashes.
However, before creating a high-availability cluster, you need to ensure that both hosts are identical
Synology NAS models with the same DSM and package versions. While different Synology NAS can act as
active and passive servers, you will experience a few limitations.
Requirements for a high-availability cluster include:
• SHA requires two identical Synology NAS to act as active and passive servers.
• The active and passive servers must be identical models and both support Synology High
Availability. The same version of DSM and package must be installed on both hosts.
• Make sure that the NAS devices do not contain SHR format volumes. Go to Storage
Manager > Volume to make sure no SHR volumes exists.
• Both hosts must be assigned static IP addresses as the cluster connection. Make sure that the IP
addresses of both hosts are accessible and belong to the same subnet; otherwise, errors might
occur when performing a switchover to the passive server. To change network settings, log in to
each host and go to Control Panel > Network > Network Interface, select the network interface
and click Edit.
Monday, November 18, 2019
• Both hosts must have the same number of LAN ports. If the hosts are equipped with additional
network interface cards, these network cards will also count as additional LAN ports.
• Synology High Availability does not support the following: Proxy servers, DHCP, DHCP server, IPv6,
PPPoE, and Wi-Fi. Please ensure that the above are all switched off before creating a high-availability
cluster.
Next steps
The next thing you need to consider is the connection between both hosts. For starters, use a
network cable to the hosts directly to each other to create a Heartbeat connection. This connection is vital
for communication as well as data replication between the primary and secondary server.
The Heartbeat connection should be connected to the same network interface on both hosts, for
instance LAN 1 on primary and secondary. Ensure that you use the fastest network interface, for example if
you have 10GbE interface cards on both, use them. Finally, this connection should not pass through routers
or switches.
Use the remaining network interfaces to connect the hosts to your network but make sure that the
connections are in the same active network. Have different switches for each host in the high-availability
cluster connecting them to the network to prevent service interruptions.
With both hosts connected properly, the next steps involve creating the high-availability cluster.
Log into the primary host as the administrator and open the High Availability Manager application.
This opens up the Create high-availability cluster wizard with information on how to create the physical
connection between servers.
Select network interfaces that you have chosen to use for the Heartbeat connection and high-
availability cluster connection. Next, enter administrator credentials of the secondary server. Specify the
name of your cluster and IP address that will enable you to access the resources of the cluster. Make sure
you select an IP address that is not in use by any other services on your network.
The wizard then checks if the system meets all requirements. If you have any data, LUN, or volume
on the primary server, you have the option of keeping it or erasing it. Next, confirm settings you made earlier
and apply.
Monday, November 18, 2019
The wizard will then present you with a set of instruction, which you must click yes to continue
before the creation of the high-availability cluster. The time it takes to create the cluster varies depending
on the environment your devices are running on. When done, the wizard will present you with a screen
featuring cluster information such as CPU utilization, load average, disk activity and connection status.
The SHA system may automatically trigger failover services from the primary server to the passive
server. The auto failover is initiated whenever:
• Storage space on the primary server crashes, but storage space on the secondary is functioning
• When errors occur on the monitored service
• In case the primary server is rebooted, shut down or both hosts lose power
Conclusion
A server malfunction can be caused by human error, component failure or even system
malfunction, leading to service interruption that can increase the cost of running a business. In order to
achieve uninterrupted availability of your data, it is critical that you take pro-active steps to reduce
administration time and costs. One way of doing this is by implement Real-Time Remote Replication on
NAP and High Availability on Synology devices.
Chrisanthi Christodoulou is working for IBSCY for the
last 4 years. She is the head of maintenance and
support department which consist of 4 people. Her
team is fully responsible for the support calls and
request of our clients internationally. She holds
several certifications from Microsoft, HPE, VMWare
and other vendors.
