Scribd
Upload
41 views

Detail of Centrifugal Pump Acid Neutralization Skid

The document provides design notes and specifications for an acid neutralization skid, including: 1. Dimensions are in mm, sharp corners should be rounded, material grades per bill of materials, and full penetration welds. 2. The skid must support a 5,000 kg payload with 1,500 kg tare weight and 6,500 kg gross weight. 3. Identification marks, nameplate holder, grounding points, and anchoring points are required.

Uploaded by

HARISH VERMA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
41 views

Detail of Centrifugal Pump Acid Neutralization Skid

The document provides design notes and specifications for an acid neutralization skid, including: 1. Dimensions are in mm, sharp corners should be rounded, material grades per bill of materials, and full penetration welds. 2. The skid must support a 5,000 kg payload with 1,500 kg tare weight and 6,500 kg gross weight. 3. Identification marks, nameplate holder, grounding points, and anchoring points are required.

Uploaded by

HARISH VERMA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

NOTES

1. ALL DIMENSIONS ARE IN MM U.O.S.


2. ROUND ALL SHARP CORNERS.
3. MATERIAL GRADE ASSUMED AS PER GIVEN BOM.
4. ALL WELDS ARE FULL PENETRATION
WELD U.S.O
5. STD.: DNV-2.7-1/2017, EN 10855/2018
6. PAYLOAD : 5000 Kg DATA NEED TO BE
9 TARE WT : 1500 Kg STENCILED 2 ALTERNATE
GROSS WT : 6500 Kg LOCATIONS ON THE FRAME
7. MIN. TEXT HEIGHT FOR STENCIL IS 50MM
8. GROUNDING POINTS (1EA BOTH SIDES)
9. ANCHORING POINTS(CARGO HOOKS) 2EA BOTH SIDES
10. MARKING AS PER DNV CLAUSE 6.1,6.1 & 6.3

290
11. NAME PLATE HOLDER
12. LADDER ON ONE SIDE
7
DESIGN NOTES:
1. LIFTING SLING ANGLE 45°
2. PAD EYE FOR 6.50 SHACKLE
3. RISK CATEGORY: LOW
4. DESIGN TEMP.: -20°C
4 4 IDENTIFICATION MARKS
1. CP8X1

2. CP8X5
3

3 17

220
NAME PLATE
HOLDER MATERIALSPECIFICATION
SL.No. DESCRIPTION MATERIAL
2
1 UC:200x46 E350
2 SHS:80x80x6 E350
3 SHS:50x50x6 E350
4 RHS:80x40x6 E350
5 SHS:75x75x4.5 E350
6 6 RHS:200x100x6 E350
2 19
7 6 THK. PLATE E275
1
8 8 THK. PLATE E275
9 10 THK. PLATE E275
10 12 THK. PLATE E275
11 30 THK. PLATE E350
8 565
M24 BOLT,WASHER,NUT
12 STD
DRAIN PLUG AND SPLIT PIN 4Nos.
LOCATION 13 LASHING RING STD

14 25 THK. GRATINGS STD


15 DRAIN PLUG WITH CHAIN STD
16 EARTHING PLUG STD
17 NAME PLATE HOLDER STD
18 ANCHORING POINTS STD
19 SHS:50x50x4 E350

16
15
EARTHING PLUG ON
5 3 DRAIN PLUG WITH CHAIN GROUNDING POINTS
1EACH BOTH SIDES

DETAIL OF CENTRIFUGAL PUMP


ACID NEUTRALIZATION SKID
TESKD-CP-001
12

10

13

DETAIL OF CENTRIFUGAL PUMP


ACID NEUTRALIZATION SKID
TESKD-CP-001
1
11
6

1
1

DETAIL OF CENTRIFUGAL PUMP


ACID NEUTRALIZATION SKID
TESKD-CP-001

You might also like