Scribd
Upload
74 views

A8 3D Printer Installation Guide

This document provides assembly instructions for an A8 3D printer in 27 steps. It begins with checking the printer parts and provides detailed pictures and warnings for each assembly step. These include screwing parts together, installing guide rods, belts, and wiring. The final steps connect the electronics and install the print head and power supply. When complete, the assembly guide congratulates the user on finishing their new 3D printer and provides contact information for support.

Uploaded by

pepe
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
74 views

A8 3D Printer Installation Guide

This document provides assembly instructions for an A8 3D printer in 27 steps. It begins with checking the printer parts and provides detailed pictures and warnings for each assembly step. These include screwing parts together, installing guide rods, belts, and wiring. The final steps connect the electronics and install the print head and power supply. When complete, the assembly guide congratulates the user on finishing their new 3D printer and provides contact information for support.

Uploaded by

pepe
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 46

A8 3D Printer Installation Guide

A8 Assembly Instructions
Attention:
1.Please make sure the package not
broken when you receive it.
2.Please check the printer parts
according to the packing list.
3. Please contract your supplier if
any questions.
A8 assembly parts list 1
A8 assembly parts list 2
A8 assembly parts list 3
A8 assembly parts list 4
A8 assembly parts list 5
A8 assembly parts list 6

Please check printer parts quantity when you receive it .


Name of each printer part
Assembly Step 1
Please be aware the screw holes is in
red circles

Step 1
Assembly Step 2
Please be aware the screw
holes is in black circles

Step 2
Assembly Step 3

Step 3
Assembly Step 4

Step 2

Step 3
Assembly Step 5
Assembly Step 6

Threaded rod 400mm


Assembly Step 7

Y Guide rod 380mm


Assembly Step 8

Attention：Leave vacancy between belt fixation


clamp and hot bed fixed plate for belt positioning.
Assembly Step 9
Before Assembly

After Assembly

Attention: Please diagonally tighten the screws when all are in there place
Assembly Step 9

Attention: Belt is for X&Y axis transmitting .Cut the length you
need to each transmission shaft. The belt is 1.5m in total and
10-20cm left after installation.
Attention: Hot bed screws should be in the bottom, and
Assembly Step 10 wing nuts will keep the height of hot bed level as well as
firming the hotbed.
Assembly Step 11 Attention: This hole is for Z axis guide rod positioning
Assembly Step 12
Assembly Step 13

Z axis Guide rod:380mm


Assembly Step 13
Assembly Step 14

Attention: loose the


jackscrew of elastic
coupling to place T
lead screw to the
bottom, then tighten
the jackscrew.

T lead screw 345mm


Attention: Please keep A&B at the same level during X
Assembly Step 15 rods installation. Knock the guide rods with a hammer
slightly if it’s hard to place.
X axis Guide rod 436mm

A
B
Assembly Step 16
Before disassembly After disassembly

After disassembly

Loose M4*6 screws first,


then separate extruder
from L black aluminum
parts, remember to
keep the screws.
Assembly Step 17

Replace M3*20
screws with M3*45
screws
M3*45 screw holes
Assembly Step 18
Assembly Step 19

Attention: Install M4*6 screw. Tighten M6 Screw


on the throat with spanner till extruder is not
loose.
Assembly Step 20
Assembly Step 21

Attention: Belt is for X,Y axis transmitting . The length of belt is


1.5m in total. Normally there’ll be 10-20cm left after installation.
Assembly Step 21

M3 Nut
Assembly Step 22
Assembly Step 23
Attention This is the wiring diagram of power supply. 1, 2, 3 seperately represent the line
of fire (brown),Zero line (blue), ground wire (yellow). 4,5, 6 represent negative pole (black)
(-);7,8,9 represent the positive pole (red) (+).To avoid danger , please assure the
installation is correct .
Assembly Step 24

Red circles stand for the power


screw holes

Power Supply
Assembly Step 25

Mainboard
Assembly Step 25
Attention: Please use the corresponding wire , especially motor wire & limited switch wire.
Assembly Step 25
Attention: Please connect the electronics wire to each components correspondingly.
Assembly Step 26
Assembly Step 27 Installation Picture 1
Assembly Step 27 Installation Picture 2
Assembly Step 27 Installation Picture 3
Assembly Step 27 Installation Picture 4
Assembly Step 27 Installation Picture 5
Installation Complete
• Congratulations ! You have just made
yourself a 3D printer !

• Please contact your 3D printer supplier if any


puzzles during using process.

• Thank you for choosing our products, we will


always provide you more services.

You might also like