Scribd
Upload
36 views

Circuito'21 Quiz: C. An SMD (Surface Mount Device) Component That Has A Size of 2.0 MM × 1.2 MM

0) An 0805 type electronic component refers to a surface mount device (SMD) with dimensions of 2.0 mm × 1.2 mm. 1) An advantage of using a through-hole component (THC) on a PCB is that it is easier to manually replace the component. 2) The component that damages itself when polarity is wrong is a symbol A component. 3) The document provides a quiz on circuitry components, PCB design, and manufacturing processes. It contains 15 multiple choice questions testing knowledge on topics like SMD/THC components, schematic symbols, PCB layer functions, and best practices.

Uploaded by

Pramila Sathsarani
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
36 views

Circuito'21 Quiz: C. An SMD (Surface Mount Device) Component That Has A Size of 2.0 MM × 1.2 MM

0) An 0805 type electronic component refers to a surface mount device (SMD) with dimensions of 2.0 mm × 1.2 mm. 1) An advantage of using a through-hole component (THC) on a PCB is that it is easier to manually replace the component. 2) The component that damages itself when polarity is wrong is a symbol A component. 3) The document provides a quiz on circuitry components, PCB design, and manufacturing processes. It contains 15 multiple choice questions testing knowledge on topics like SMD/THC components, schematic symbols, PCB layer functions, and best practices.

Uploaded by

Pramila Sathsarani
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Circuito’21 Quiz

1. 0805 type of an electronic component means?


a. A through hole component which has a diameter of 5mm
b. A resistor with a value of 805 ohms
c. An SMD (Surface mount device) component that has a size of 2.0 mm ×
1.2 mm
d. An inductor with a value of 805mH

2. What is an advantage of using a through hole component (THT) in a PCB?


a. Saves space on the PCB.
b. Easier to be assembled by machines
c. Easier to manually replace the component
d. Takes less energy to solder

3. Which component damages itself when polarity is wrong.

a. Both
b. None of above
c. Symbol A
d. Symbol B

4. What is the correct statement for following circuit symbols?

a. No electrical difference, US and EU have different symbols for resistors.


b. Symbol on the left is a resistor that can be used to carry high currents.
c. Symbol on the left is the symbol for an induction heater.
d. Symbol on the right is a LDR (Light Dependent Resistor)
5. What is the correct statement regarding wire and bus tools in the wiring tools menu?

a. Wire and Bus tools act the same, just the symbol difference between US &
EU.
b. Bus is a connection shared between multiple components.
c. Bus can only be used to connect two components.
d. Wire can send more current.

6. Statement which is not an advantage of using Net Port tool (highlighted below) in the
wiring tools menu.

a. Net ports can be used to make circuit more modular


b. Net ports can be used to connect between components far away easily.
c. Net ports allow the schematic to be more readable & user friendly.
d. Net ports can be used to close unwanted pins

7. What is the purpose of a ‘no connect flag’?

a. Delete a wire
b. Delete a pin
c. Indicating a pin has no connection
d. Mark a connection with errors
8. Which layer determines where the edge of the PCB is going to be cut during
manufacturing.

a. Top Layer
b. Bottom Layer
c. Multi-Layer
d. BoardOutLine

9. Which of the statements about the following image is correct?

a. Routing is done only on the top layer.


b. Routing is done only on the bottom layer.
c. Routing is done only on the top silk layer
d. Routing is done only on both top & bottom layers.
10. What is the purpose of a via?

a. To draw a circle
b. To create a plated hole to conduct electrons between two layers.
c. Connect two routes in same layer
d. Measure distance between two holes

11. What should not be considered as an electrical impact in PCB designing?


a. Routing width
b. Masking colour
c. Distance between routing paths
d. Power ratings of components

12. What is the software that cannot be used for PCB designing?
a. Altium
b. Upverter
c. Processing 3
d. KiCad

13. Which step is not a good practice in the PCB manufacturing process at home?
a. Cleaning the copper board with ferric chloride before ironing the PCB
b. Cleaning the copper board with soap and water before ironing the PCB
c. Drawing on routing paths using a marker before etching
d. Using protective gloves when etching the PCB

14. What should not be considered when calculating the PCB trace width?
a. Trace current
b. PCB thickness
c. Temperature rise
d. Layer of the trace
15. What is the suitable layer to place a logo on the side shown as in the below image?

a. Top Layer
b. Bottom Layer
c. Top Silk Layer
d. Bottom Silk Layer

You might also like