BWC/ISD-T-9A

MANUFACTURERS’ DATA REPORT FOR UNFIRED PRESSURE VESSELS

1. Manufactured by: __________________________________________________________________________

(Name and Address of Manufacturer)

2. Manufactured by: __________________________________________________________________________

(Name and Address of Purchaser)
3. Type: ________________ Kind ___________________ Vessel No. _______________ Year Built __________
(Hor. Or Vert.) (Tank, Jacketed, Heat Exch.)

_____________________________________________________________________________________________
Items 4 to 9 inclusive to be completed for asingle wall vessels (such as air tanks, jackets or jacketed vessels, or heat
of heat exhangers)
____________________________________________________________________________________________

4. Shell: Material ___________________ T.S. _______________ Nominal Thickness ____________ in. ________
(Kind & Spec. No.) (Fig. Or F.B. & Lowest T.S.)

Corrosion Allowance ______________________ in. Diameter _______________ Ft. _______ in.

Length ___________ft. ___________ in.

Butt Joint
5. Seams: Longitudinal __________________ Stress Relieved _________________ X-Rayed ___________________
(Welded, Dbl., Single, Lap, Butt) (Yes or No) (Spot or Complete)

Sectioned No. of Course If riveted describe seams

Welder Classification: _____________________ fully on reverse side of
(Class A, B. C) form.

6. Heads: (a) Material _________________ T.S. ________________ (b) Material _____________ T.S. __________

Location Drown Knuckle Elliptical Conical Hemispherical

(Top, Bottom, Ends) Thickness Radius Radius cal Ratio Ratio Apex Angle Radius

(a) ______________ ________________ ______________ _______________ ________________

(b) ______________ ________________ ______________ _______________ ________________

Flat Side to Pressure

Diameter (Convex or Concave)
_____________________ _____________________
_____________________ _____________________

If removable, belt used __________________________________ Other Fastening ___________________

(Material Spc. No., T.S.. Size, Number) (Describe or attached
sketch)

7. Staybolts: ___________ If hallow _________________ Attachment _____________ Pitch ___________ Dia.

__________
(Materials) (Size of Hole) (Threaded or Welded) (Hor.) (Vert.) (Nominal)

8. Jacket Closures: ________________________________________________________________________________

(Describe as Egg. & Weld, bar, etc. If bar give dimension. If bolted, described or sketch)

9. Tube Sheets: Stationary Material _______________________________ Diam. _____________________________ in.

(Kind & Type) (Subj. to Press)

10. Tubes: Material __________________ O.D. in. Thickness _________________ or Gage No. ____________________
Type __________________________
(Straight or U)
 Item 12 to 15 inclusive to be completed for inner chambers of jacketed vessels of heat exchangers.

11. Shell: Material ___________________ T.S. _____________ Nominal Thickness _____________________________ in.
(Kind of Sec. No.) (Fig. or F.B. & Lowest T.S.)

Corrosion Allowance _____________ in. Diam. _________ Ft. _______ in. Length ________ft. _____________in.

Butt Joint
12. Seams: Long __________________ Stress Relieved _________________ X-Rayed ___________________________
(Welded, Dbl., Single, Lap, Butt) (Yes or No) (Spot or Complete)

If riveted describe
fully on reverse side of
form.

Sectioned _______________________ No. of Course __________________________________________

(Yes or No)

13. Heads: (a) Material _________________ T.S. ________________ (b) Material _____________ T.S. __________
(b) Material _____________ T.S. ________________________________

Location Thickness Crown Knuckle Elliptical Conical

Radius Radius Ratio Apex Angle
(a) Top, Bottom,
Ends _____________ ___________ ___________ _____________ ____________
(b) Channel _____________ ___________ ___________ _____________ ____________
(c) Floating _____________ ___________ ___________ _____________ ____________

Hemispherical Flat Side to Pressure

Radius Diameter (Convex or Concave)
_____________________ _______________________ ______________________
_____________________ _______________________ ______________________
_____________________ _______________________ ______________________

If removable, bolts used (a) __________________________________ (b) _________________________

(Material Spc. No., T.S.. Size, Number)
(c) __________________________________Other Fastening _______________
(Describe or attached sketch)
(int.)
15. Constructed for ____________ pressure of ___________ psi. Max. Temp. _______ oF Subzero ________________
(ext.)

oF Hydro Test _________psi.

Item below to be completed for all vessels where applicable

16. Safety Valve Outlets: Number _________________ Size _______________ Location ____________________

17. Nozzles:
Purpose (Inlet, Diameter Reinforcement
Outlet, Drain) Number or Size Type Material Thickness Material How attached
____________ ______ _____ _____ ________ __________ __________ ____________
____________ ______ _____ _____ ________ __________ __________ ____________
____________ ______ _____ _____ ________ __________ __________ ____________
____________ ______ _____ _____ ________ __________ __________ ____________

18. Inspection Manhole, No. _________________ Size __________________ Location _______________________

Openings: Handhole, No. ________________ Size __________________ Location _______________________
Threaded, No. ________________ Size __________________ Location _______________________

19. Supports: Skirt __________ Lugs ___________ Legs _____________ Others __________ Attached _________
(Yes or No) (Number) (Number ) (Describe) (How and Where)

20. Remarks: __________________________________________________________________________________

(Brief description of purpose of the vessel, as Air Tanks, After

___________________________________________________________________________________________
Cooler, Jacketed cooler, etc. State contents of each part. )
 We certify that the statements made in this report are corrected and that all details of material construction, and
workmanship of this unfired pressure vessel conform to the ASME code for unfired Pressure Vessels.

Name and
Name & Signature,
Date ____________________, 19 __________ Signature ____________________ Seal _________________________
(Manufacturer) (Name and Signature)
Professional Mechanical Engineer

ABOVE SPECIFICATIONS APROVED:

Date ______________________, 19 __________

____________________________________
Professional Mechanical Engineer