TK101 Multi-functional Tracker

User’s Manual
Table of contents
 Chapter I Preface
I. General
TK101 represents the perfect combination of GSM and GPS technologies. This model, with precise
dimensions and compact appearance, expresses the advanced workmanship in the GSM and GPS field and is
the typical design combing communication products and GPS services.
As a professional security and positioning company, we will provide you with more and better
products and services. Before use, please spend several minutes reading this user’s manual in order to
understand operation details and obtain better services.
II. Notices
1. Please read carefully this user’s manual and always use correct operation methods to prevent any
possible errors.
2. This user’s manual is for reference only. If some contents and operation steps are inconsistent with
those for the actual product, the latter will prevail.
3. The defaulted password of this product is 0000.

Chapter II About the Device

TK101, as a personal remote positioning device made up of GPS module and GSM/GPRS module, is
compact in dimensions and has high accuracy. On the basis of GPS satellites and under dynamic conditions, it
can provide you with accurate and correct location information. With such features, it can be used to protect
and look for our old people and children. You can use it for safety purpose and other purposes, such as remote
positioning to protect property safety and follow animals.

I. Components
1. Inbuilt GPS Module

2. Internet positioning service center, used to receive and send positioning information.
II. Product Features
● GPS individual or fleet positioning;
● GSM /GPRS modem supports two frequency bands, i.e. 900/1800 850/1900 MHz(options)
● High-sensitivity, new workmanship and the most advanced GPS chip;
● Can accurately position even if with weak signals;
● Can work effectively in limited space such as the remote and narrow places in a city;
● Low energy consumption;
● Fast signal capturing;
● Supports single positioning and continuous tracking;
● Supports alarming and remote monitoring;
● Supports fast dial button;
● Supports the location information inquiry by SMS and Internet
● May monitor without disturbing the tracked person and realizes real-time tracking;
● Can position the holder by call or mobile phone SMS;
● In emergency, press the SOS button to have an accurate positioning.

III. Product Specifications

1. Technical Specifications
GSM module GSM850/1900Hz or GSM900/1800MHz, two combinations
GPS chip Latest
GPS sensitivity -159dBm
GPS center frequency L1, 1575.42MHz
GPS positioning accuracy 5-25m
GSM positioning accuracy 100-500m
Speed accuracy 0.1 m/s
Time accuracy Synchronous with GPS
Default data WGS-84
Hot start 1s
Warm start 38s
Max. altitude 18000m
Max. speed 515m/s
Gravitational acceleration 4g

2. Others
Working temperature -20---65
Humidity 5%---95%
Dimensions 80×49×16 mm
Voltage Rechargeable 800mAh battery
Power supply DC5V
Standby time >48h
Buttons One SOS emergency button for emergency aid; Call 1, Call 2,
Receive and Hang up buttons.

Chapter III Use Preparation

I. Accessories
1. Main unit
2. USB data cable
3. Charger
4. Headset cable (optional)
II. Charge the Battery
Before the use of the tracker, please charge the battery at least 4h via the USB charging cable. For the first
charge, in order to bring the performance of the battery into full play, charge it above 12h.
Indicator of charging:
Red, being charged;
Green, charging completed.

III. Installation of SIM Card

Open the back cover, then you will see the place where the SIM card is placed. Then push the SIM card into
the slot until it comes into its proper position completely and make sure it is locked. See the following figures:
Choose SIM card:
• The type of the SIM card is GSM card (the SIM card of China Mobile is recommended).
• Make sure the SIM card has sufficient amount in order to pay the communication cost.
• Prepare one piece of SIM card for mobile phone (the SIM card of China Mobile is recommended),
make sure that the card has opened such functions of Caller ID and receiving and sending messages. If
necessary, use the service platform to track the GPRS function to be opened in real time.

Chapter IV Basic Function and the Operation Way

Open The Unit
Press the power switch which the right of the unit about 3s then can hear the voice of switch on. Usually,
you can press this power button to confirm whether the state of unit is switch on or off.
Main Function
Function Command Note
Mode Change #70x#0000## This unit can support four
different mode and can change
mode each other.
#700#0000##
When X=0, the mode is P2P
mode,the feedback will send to
the mobilephone of the sender.
#701#0000##
When X=1, the mode is SMS
Center Way mode,the feedback
will send to the saver numberof
the unit.
#703#0000##
When X=3, unit is in the
GPRS Mode.
#704#0000##
When X=4, unit is in the
GPRS Mode,the different as
X=3 is that when the data is
 change what is less than 10
meters, the unit will send the
data to the server as 1/10.
#705#0000##
When X=5, the unit is in
GPRS Mode,and the unit will
send the data to the server as the
configuration way .
Point to Point 666+Password The unit will send the latitude
Function1 Single and longitude information to the
Position sender after send 666+Password
in 700 Mode .
The unit will send the latitude
and longtitude information to
the center number after send
666+Password in 700 Mode.
The unit will send a Position
Message to the GPRS Center in
703,704,705 Command .
Point to Point Function 988+Password the sender mobilephone or
2 SMS Center will receive a
geography information in any
mode.
Point to Point Function 987+Password The sender mobilephone or
3 SMS Center will receive a web
link, and open this link, can see
the current position (Option)
Set Center Number #710#15814058277#0000## After you send this command,
15814058277 will be the Center
Number,the unit will send
message to this numbersuch as
Alarm with Lower Power or
SOS Alarm
How to upload to the 1.Set IP and If you want to connect with
software (GPRS Mode) Port #803#210.211.31.217#6789#0000##Or set the our software, please contact
IP and Port by a domain name with someone in this company.
#803#http://www.zsdgps.cn/ZSDWebGPSEng#233
5#0000##
2. Set the Upload Time and The number of the data:
703 Command
#730#20#4#0000##
3. Change the mode from Point to Point to Center
Mode : 703 Command
#703#0000##
Monitor the position Set the upload interval Time 730 Command When you set the 701
continuous(SMS #730#20#4#0000## Command,
Channel) theposition information will
Change the mode to Point to the Center or Point to
Point mode :#701#0000## send to the SMS Center. when
#700#0000## you set 700 Command, the
position message will send to
the mobilephone of sender
Change the Time Area #721#E08#0000## After you send this command,
of Upload Data the upload data time will change
it to East 8 area time, if you
want to set the West 8area, you
can send #721#W08#0000##
Dial and hang on the Send the 711 command to save phone in the unit After you set this command,
phone by two way Eg #711#13900139000###0000## when you press the "Call 1",
and can dial the first and second
number, press " Call2" can dial
the third number. if a new
number is coming, you can
listen by hang up button, hang
down button for close
Monitor Function Send : 555+Password After the unit receive this
Eg: 5550000 command, the unit will call the
sender
SOS Alarm Send SOS Alarm Command : 720 The default state is close this
Eg #720#3#0000## funciton ,so if you don't set 720
command, the unit will not take
This command is mean that when you press the
alarm even press the SOS
SOS Button, the unit will call to the center number Button
and send SOS Alarm message to the center number
Geo Fence Function Send 750 Command This command is mean that
#750#radiusmeters(5digits)#interval(minutes)#pass the unit will get the gps satellite
and get the correct, then the first
word## position will be the basic
Choose the current point to the basic point. point,after configuration,the unit
#750#100#1#0000# will check whether the unit is
over the area every one minute
(the time you can set it ) , if
over the area, the unit will take
alarm to the sender
(2)This command is that get
the single latitude and longitude
(2)#751#500#5#2234.5848N#11354.028#0000## to set the geo fence, put
2234.5848N,11354.028E be the
origin point, and the radius is
500meters for the area .
Cancel or Check the 1 #760#0000# 1 This command can cancel
Geo Fence Function the geo fence function that you
already set it ago.
2 This command can check
2 #752#0000#
the information of geo fence
Change the password of #770#1111#0000## Change 0000(initial password)
Unit to 1111 (new password)
APNConfiguration See the detail information in the Manual Different SIM Card have
#802#gprsweb.digitel.ve###0000## Different APN, please pay
attention this .
Other Function 1 #901## 1 Read the User data
2 #902## 2 Read the GPRS Data
3 #903## 3 Restart the Unit
4 #904## 4 Connect with the
5 #905## GPRS 5 Cut Off GPRS

Chapter V Commands Corresponding to and Operation Method of Basic Functions

1. Location Inquiry
(1) SMS Inquiry
Create 666 + password command (defaulted password as 0000) via mobile phone and send it to the student
terminal mobile phone number; after successful sending, the guardian’s mobile phone will receive a piece of
word message. See the flow as follows:

By the same means, send the command 987 + password to the terminal, then the terminal will return one
piece of website message. The guardian may inquire the location information of the ward attached with local
map through this website message.
(2) Platform Inquiry
Step 1: Log onto the platform;
Step 2: Click the terminal of the ward, then the map will display the location of the ward.
2. Setup of Center Number
Set the center number by means of SMS through mobile phone. After the setup is successful, then the
mobile phone sending the SMS will receive the “config OK” response message from the terminal.
Command format: #710# center number # user password ##
For example: #710#134xxxxxxxx#0000##
Note: All alarming information thereafter including SOS, low power, electronic fence, etc will be returned
to such number.

3. Bi-directional Call Function

Send the command in form of SMS through mobile phone to the terminal. After the setup is successful,
after sending the SMS, the mobile phone will receive the config OK response message returned from the
terminal.

Setup format: #711# Call 1# Call 2 # Call 3 # 0000##

For example:

Note: After the setup is successful, press the CALL 1 button, then the terminal will automatically dial the
first phone number. Press the CALL 2 button, then the terminal will automatically dial the second phone
number. In addition, the terminal may receive all calls by pressing the Receive button and end all calls by
pressing the End button.
Remarks: The automatic receiving function of the terminal. For all calls, if the terminal does not choose to
end or receive within 30s, they can be received automatically.

4. SOS Function
If a ward number (the number in 3 above) is set, when the ward encounters emergency and presses the
SOS button, then the terminal will send alarming information to the center number and dial three ward numbers
in order.

5. Monitoring Function
The ward may send SMS 555 + password to the terminal of the ward; in such case, the ward terminal of
the ward will automatically call back the mobile phone of the guardian and the guardian may listen to the sound
of the surroundings within 10m around the ward.
SMS format: 5550000
 Remarks: 0000 is the initial default password and the actual use s subject to the actual password.

6. Regular Upload Interval Setup

The defaulted factory upload interval of this device is 2 minutes for getting the point and 10 minutes for
uploading one piece of positioning information. The user may change such parameter according to actual
demand.
Command format: # command number 730# Sampling interval # Pieces of uploads # User password ##
For example: 730#20#4#0000##
Note: The parameter “20” indicates getting one point every 20s; after getting points accumulatively for 4
times, upload one piece of positioning information with the upload interval as 20*4=80s. The user may change
this parameter as the case may be.

7. Function of Changing Password

Send the SMS “#770# User new password # User old password ##” by mobile phone to the terminal
number, after successful sending, the mobile phone with such setup will receive one piece of config ok
response information, as shown in the following figure:

8. Low-Voltage Alarming Function

If the terminal of the ward has a very low power and needs to be powered off, the terminal of the ward will
automatically upload one piece of low-voltage alarming command to the monitoring center number.

9. Set APN Command

Create the SMS “802#APN letters or digits, 4-20 bits # Log user name letters or digits 4-20 bits in # Log
password letter or digits 4-20 bits in # terminal password 4 bits ##” and send it to the terminal; after executing
this command, the terminal will automatically restart and connect to GPRS with APN set.
Command example 1: #802#cmnet###0000###
Command example 2: #802#CCDLEN#QIUXIA.21#RX0000#0000##
After this command is executed, APN will be CCDLEN; the login user name is QIUXIA.21 and login
password is RX0000.
Note: The default APN of this product is CMNET.
10. Electronic Fence Function
(1)GPS Fence Function
 The guardian may log into the system, click the custom deviation setup in the user system manager, enter
the deviation setup interface, choose the longitude and latitude of the center point to be set as fence. Click the
mouse in the Google map, then reading page will display the electronic fence with longitude and latitude set.
See the figure below:

Set fence format: # command number (751) # fence radius # sampling interval # longitude # latitude #
user password ##.
For example: #751#500#5#22.5442N#113.91E#0000##
After the setup is successful, the setting mobile phone will receive a piece of config ok command. Then,
when the ward leaves this area, the terminal will send the alarming information of being out of the fence to the
center number.
(2)GSM Fence Function
The ward may send # command number (740) user password 4 digits ## command to set the GSM
fence. After the setup is successful, the terminal will return the message of CONFIG OK to the setting
mobile phone, or the message of PASSWORD ER if the password is wrong.
For example: #740#0000##
Description of GSM fence: The terminal reads the GSM base station information, including that the main
base station and the adjacent base stations. Take the first four digits and keep them in the module. If the
base station has many data with different first digits, they all must be saved. And initiate the protection
status. In the state of protection, the module will read the data of all base stations (1-7) once every 5
minutes, and take the first 4 digits to compare with the protection data. If all the first 4 digits of the data of
all base station are consistent with the existing data, then dial or send alarming messages to the user
according to the alarming setup.
For example: #740#0000##. After the fence is set, the terminal will alarm in the case where it is moved
about 3-5km out of the fence.
(3) Fence Reading Function
Send commands to the terminal: # command number (752) # user password 4 digits ##; after the
command is set successfully, the terminal will read the data of the module fence working status and return
message to the sending mobile phone, or PASSWORD ER if the password is wrong.
For example: #752#0000##
Return: #open:1#lat:11456.209400#lng:2233.470100#distance:500#time:5#status:2
Where, open: 1 indicates fence open; Open: 0 indicates fence closed;
lat:11456.209400, latitude;
lng: 2233.470100; longitude;
distance: 500; fence radius;
time: 5 sampling interval;
status: 2 , terminal has obtained valid satellite data, fence works normally;
status: 1; fence open, but there are no valid satellite data have been received;
status: 0, no electronic fence is set.
(4) Function of Canceling Fence
Command name: # command number (760) # user password 4-digits ##
Example: #760#0000##
After the terminal receiving this command, all fence settings will be cancelled.
Advice Do not set GSM fence and GPS fence at the same time.
11. Auxiliary Functions:
(1)#901## Command of reading user parameters;
(2)#902## Command of reading GPRS parameters
(3)#903## Restart command
(4)#904## GPRS connection command
(5)#905## GPRS disconnection command

Notices:
1. This device is of non-waterproof design.
2. This device must work with the cooperation of GSM/GPRS network.
3. Make sure that the SIM card has sufficient balance in order to avoid inconvenience in use.
4. This device will not be able to work in case of power-off and out of the service area, even if you are a
registered user.
5. This device supports the dual positioning mode of GPS and GSM/GPRS.
6. Please use this device in a legal area, any illegal consequence will be borne by the user.