Please be aware that direct sunlight onto the PIR lens, or extremes of temperature (above 30 deg

1 Introduction C) may affect the operation of the detector. Always ensure roof light blinds are closed if sunlight
could shine directly onto the PIR.
Welcome to the AS210 mobile alarm system.
Using the latest microprocessor technology the AS210 provides all year round protection for your
2.4 Tilt Sensor
mobile home. The AS210 alarm system has an inbuilt tilt sensor that detects tilting of the vehicle during the
To ensure your alarm system is operated correctly, please read all sections of these instructions hitching process. If the tilt sensor is not set correctly (i.e. pushed to front or back) and the alarm is
before attempting to operate the alarm system. If you are unsure of any content, please contact armed, the siren will be triggered after a 5 second delay. To cancel the siren, press the key fob
your supplier in the first instance or the manufacture direct (see section 6). button (see 2.1) and then readjust the tilt sensor as follows;
During normal (on the flat) operation the tilt sensor adjustment lever should be left in the centre
2 Operation position (notched position).
If the vehicle is parked on a steep slope it may be necessary to adjust the tilt sensor. Firstly arm,
2.1 Arm / Disarm and then disarm the alarm to activate the internal LED tilt indicator light. While viewing the slot
adjacent to the adjustment lever, move the lever forward until the light in the slot illuminates /
The AS210 Alarm System is supplied with two key ring style radio controllers, which are used to flashes. Note the position of the lever.
control the alarm system. The system can be operated in different modes as follows; Secondly, move the lever backwards, and again note the position of the lever when the light in the
Standard Mode - Arm / Disarm slot illuminates / flashes. Now set the lever mid way between the two positions.
To fully arm the system with internal movement sensor and tilt sensor active, first exit the vehicle, Remember to return the lever to the centre ‘notched’ position when returning to ‘on the flat’ use.
then press and hold the key fob button until you hear a single long beep, then release the button. Although not recommended in all cases as nuisance triggering can occur, the sensitivity of the tilt
Arm = BeeeeeeeP sensor can be increased by moving the tilt lever towards the rear of the vehicle. Move the lever
To disarm the alarm system press and hold the key fob button until you hear two short beeps, slowly backwards until the tilt indicator light illuminates, then move the lever forward about 2mm.
then release the button. Note: when the alarm system is disarmed the tilt lever is disabled after 1 minute of operation to
Disarm = BeeP BeeP conserve battery life (just in case the lever is left in the ON position). To reactivate the lever, Arm
Special Mode - Arm / Disarm then Disarm the system.
(A) To arm the system with only the tilt sensor active, first exit the vehicle, then press and hold the
key fob button until you hear a single long beep, continue holding the button until you hear a 3 Key Fob Controllers
further single long beep, then release the button.
The AS210 alarm system comes complete with 2 key fob remote controllers. If additional
Arm = BeeeeeeeP BeeeeeeeP controllers are required these can be ordered from your supplier.
(B) To arm the system with only the internal movement sensor active, first exit the vehicle, then
press and hold the key fob button until you hear a single long beep, continue holding the button 3.1 Key Fob Battery Replacement
until you hear a further two long beeps, then release the button.
1) Remove the key fob from your key ring.
Arm = BeeeeeeeP BeeeeeeeP BeeeeeeeP
2) Remove the single casing ‘pozi-drive’ screw.
To disarm the alarm system press and hold the key fob button until you hear two short beeps,
then release the button. 3) Remove one half of the casing and remove the old battery.
Disarm = BeeP BeeP 4) Install the new battery (23A 12 volt Alkaline) ensuring the positive [+] terminal is located
towards the [+] mark on the key fob circuit board. The coiled spring connection in the key fob
Remember that you must allow at least 60 seconds between arm and disarm otherwise the alarm
is the battery negative [-] terminal.
system may think you are selecting a special arm mode.
5) Relocate the two casing half’s and install the casing screw.
2.2 Alarm Siren 6) Refit the key fob to your key ring.
When the alarm is triggered the siren will sound for 1 minute. Following the 1-minute period the 7) Remember to dispose of old batteries in accordance with local regulations.
alarm will then deactivate for 15 seconds and then rearm.
The alarm siren can be turned off at any point by pressing the key fob button (see 2.1). 4 Battery
2.3 PIR internal Movement Sensor The AS210 alarm system incorporates a 3.3Ah sealed lead acid battery that is charged from the
vehicles 12v supply. This battery has been selected to run the alarm in ‘armed mode’ without any
The AS210 alarm system comes complete with a 120° Passive Infra Red (PIR) internal movement external supply voltage for up to 6 months depending on ambient temperature / initial charge.
sensor that detects body movement within the vehicle. The battery is fully charged when the alarm system is despatched, but may need further charging
If you are leaving pets within the vehicle the system should be armed in special mode (A) to if the vehicle is stood for a number of months without any 12v supply to the alarm. It is
prevent your pet from triggering the alarm. recommended that alarm system is permanently connected to a 12v supply.

Issue 03 Page 2 Page 3 05/02/2005

 To charge the alarm battery either fit a fully charged leisure battery to the vehicle or connect the
vehicle to the mains supply and switch on the 12v charger / power supply. It may take up to 7
days to fully charge the battery.
The internal battery should be replaced approximately every 3 years to ensure correct operation.
Replacement batteries can be ordered from your supplier. Always dispose of old batteries in
accordance with local regulations.

5 Specification
5.1 Control Box
Supply voltage: 10.5 to 15v DC
Supply current: 250mA max 20mA typical
Operating temperature: -5 to +30 deg Celsius
Battery capacity: 3.3Ah at 12v
Operating time (armed) with no external supply: 6 months at 20° Celsius

· Remote Controlled
Siren output: 110 dB +/- 10% @ 1M
Interface connector: Negative trigger in, Negative trigger out, System negative

5.2 PIR Movement Sensor

Range: 120° x 6M
Current Consumption armed: <1mA typical
· PIR Movement Detector
5.3 Key Fob Controller
Range: 6M typical · Battery Backup (up to 6 months)
Battery: 23A 12-volt cell
Typical battery life: >1 year

6 Spare Parts / Service · Adjustable Tilt Sensor

For Interface harnesses, installation documentation, spare parts, local supplier contact details or
other service information please contact:
Sargent Electrical Services Ltd. service desk on 01482 678981 during normal office hours.
· Loud 110dB Siren with Timer
Further technical information is available at WWW.Sargentltd.co.uk

· Interface Connector

· Auto Reset

· Easy Fit Design

Issue 03 Page 4 Page 1 05/02/2005