Scribd
Upload
364 views

Bluetooth Protocol Stack

The document discusses the Bluetooth protocol stack including the baseband layer, link manager protocol, service discovery protocol, RFCOMM, L2CAP, telephony control protocol specification, host controller interface, adopted protocols like PPP, TCP/IP, OBEX, and WAP/WAE. It also mentions the Bluetooth radio transmitter and receiver characteristics.

Uploaded by

kayal_ece
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
364 views

Bluetooth Protocol Stack

The document discusses the Bluetooth protocol stack including the baseband layer, link manager protocol, service discovery protocol, RFCOMM, L2CAP, telephony control protocol specification, host controller interface, adopted protocols like PPP, TCP/IP, OBEX, and WAP/WAE. It also mentions the Bluetooth radio transmitter and receiver characteristics.

Uploaded by

kayal_ece
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

1.

Bluetooth Protocol Stack

BaseBand

The baseband and the Link control layers enable the physical RF link between
bluetooth devices to form a piconet. Both circuit and packet switching is used. They
provide two kinds of physical links using the baseband packets. Synchronous
connection oriented (SCO) and Asynchronous connectionless (ACL). ACL packets are
used for data only, while the SCO packets may contain audio only or a combination of
audio and data.
Baseband is the physical layer of the Bluetooth which manages physical channels
and links apart from other services like error correction, data whitening, hop selection
and Bluetooth security

Judy Simon M E Applied Electronics II Sem Sathyabama University


The Link Manager Protocol
The link manager protocol is responsible for the link setup between bluetooth
units. This protocol layer caters to issues of security like authentication, encryption by
generating, exchanging and checking the link
and encryption keys. It also deals with control and negotiation of baseband packet sizes.

Service Discovery Protocol (SDP)


SDP is the basis for discovery of services on all Bluetooth devices. This is
essential for all bluetooth models. Using the SDP device information, services and the
characteristics of the services can be queried and after that a connection between two or
more Bluetooth devices may be established. Other service discovery protocols such as
Jini, UpnP etc. maybe used in conjunction with the Bluetooth SDP protocol.

RFCOMM
The RFCOMM protocol is the basis for the cable replacement usage of bluetooth.
It is a simple transport protocol with additional provisions for emulating the 9 circuits
of RS-232 serial ports over L2CAP part of the bluetooth protocol stack. This is based in
the ETSI standard TS 07.10 and supports a large base of legacy applications that use
serial communication. It provides a reliable data stream, multiple concurrent
connections, flow control and serial cable line settings. transfer

Logical Link Control and Adaptation Layer (L2CAP)


The bluetooth logical link control and adaptation layer supports higher level
multiplexing, segmentation and reassembly of packets, and Quality of Service (QoS)
communication and Groups. This layer does not provide any reliability and uses the
baseband ARQ to ensure reliability. Channel identifiers are used to label each
connection end point.

Telephony Control Protocol Specification (TCS Binary)


The TCS binary protocol defines the call control signaling for the establishment
of speech and data calls between bluetooth devices. It is based on the ITU-T Q.931
recommendation. It is a bit oriented protocol and also provides group management.

The Host Controller Interface (HCI)


The HCI provides a command interface to the base-band controller, link manager
and access to the hardware status and control registers. The interface provides a uniform
method of accessing the Bluetooth baseband capabilities. The Host control transport
layer abstracts away transport dependencies and provides a common device driver
interface to various interfaces. Three interfaces are defined in the core specification:
USB, RS-232, and UART

Judy Simon M E Applied Electronics II Sem Sathyabama University


ADOPTED PROTOCOLS
PPP, TCP/IP

PPP, TCP, UDP and IP are standard Internet protocols defined by IETF. These are used
as the lower layer protocols of the WAP stack.

Specification and Description Language (SDL)


It is an object-oriented, formal language defined by ITU-T as recommendation
Z.100. The language is intended for specification of complex, event driven real-time,
and interactive applications involving concurrent activities that communicate using
discrete signals.

OBEX
OBEX is a session protocol defined by IrDA. This protocol is also utilized by
bluetooth thus enabling the possibility for application to use either the Bluetooth radio
or IrDA technologies.

WAP/WAE
Bluetooth may be used as a bearer technology for transporting between a WAP
client and a nearby WAP server. WAP operates on top of the bluetooth stack using PPP
and the TCP/IP protocol suite.

Bluetooth radio:
Bluetooth radio is a transceiver which transmits and receives modulated electrical
signals from peer Bluetooth devices. The radio for compatability reasons should have
some defined transmitter and receiver characteristics.

Judy Simon M E Applied Electronics II Sem Sathyabama University

You might also like