Harold Vance Department of Petroleum Engineering

Texas A&M University

Petroleum Engineering 201S

Introduction to Petroleum Engineering

Notes on Dimensions and Units

Spring 2002
2
Fluid Properties
1. Liquid Specific Gravity
 liquid
 liquid 
 water

2. API Gravity
141.5
° API   liquid
 131.5

3. Gas Specific Gravity

 gas Mg M g(pure gas) M apparent( gas mixture)
 gas    
 air M air 28.97 28.97

4. Gas in Solution
Rs = standard cubic feet of gas liberated when one stock tank barrel of crude oil is
produced

5. Oil Formation Volume Factor

volume occupied at reservoir pressure and temperature
B = volume occupied at standard pressure and temperature

B= . In other words:

 RB 
B=  
 STB 

mass of oil mass of gas

  STO  0.01357R s  g
STB STB
= = ,
mass of reservoir liquid  oR
RB

where: and are densities of the stock tank oil and reservoir liquid, both in
lbm/ft3, and 0.01357 converts the gas volume to mass.
The conversion factors is derived as follows:

 Scf  lb  mole  28.97  g lb m  STB  lb

Rs     = 0.01357R g m .
  
 STB  380.7 Scf  lb  mole 3
 5.615ft  ft 3

3
Example Fluid Properties Calculations

1. Liquid Specific Gravity

Given
Density of Liquid 48.6 lbm/ft3
Density of Water 62.4 lbm/ft3

Definition
 liquid
 liquid 
 water

Calculation
 liquid 48.6
 liquid    0.779
 water 62.4

2. API Gravity
Given
Specific gravity of liquid-1 0.779
Specific gravity of liquid-2 0.876
Specific gravity of liquid-3 1.000

Definition
141.5
° API   liquid
 131.5

Calculations
Specific Gravity API Gravity
0.779 50.0
0.876 30.0
1.000 10.0

3. Gas Gravity
Given Component Composition (Mole fraction)
Methane C1 0.850
Ethane C2 0.090
Propane C3 0.040
n-Butane n-C4 0.020
Definition
 gas Mg M g(pure gas) M apparent( gas mixture)
 gas    
 air M air 28.97 28.97

4
3. Gas Gravity (continued)
Calculation
Component
Component Mole fraction Molar Mass Mass Mass fraction
j yj Mj y jM j y j M j / 19.26

C1 0.850 16.04 13.63 0.708

C2 0.090 30.07 2.71 0.141
C3 0.040 44.10 1.76 0.091
n-C4 0.020 58.12 1.16 0.060
1.000 19.26 1.000

M apparent( gas mixture) 19.26

 gas   0.665
28.97 28.97

4. Oil Formation Volume Factor

Given
Density of Reservoir Oil 47.5 lbm/ft3
Density of Stock Tank Oil 55.5 lbm/ft3
Gas in Solution 400 Scf/STB
Gas Gravity 0.72
Definition
 STO  0.01357R s  g
Bo =
 oR
Calculation
55.5  (0.01357)(400)(0.72) RB
Bo =  1.251
47.5 STB
5. Gas Formation Volume Factor
Given
Reservoir Pressure 1000 psi Standard Pressure 14.65 psi
Reservoir Temperature 610 oR Standard Temperature 60 oF
Gas Law Deviation Factor (z) 0.90
Definition
Vrc
Bg =
Vsc
Calculation
Vrc  nzRT / p  rc (0.9)(610)(14.65) Rcf RB
Bg =    0.0155  0.00275
Vsc  nRT / p  sc (60  460)(1000) Scf Scf

5
Fluid Properties Nomenclature
Lower Case Letters
n Amount, moles
nrc Amount at reservoir conditions, moles
nsc Amount at surface conditions, moles
p Pressure, FL-2
prc Pressure at reservoir conditions, FL-2 (psia)
psc Pressure at surface conditions, FL-2 (psia)
z Gas law deviation factor, actual volume/ideal volume
zrc Gas law deviation factor at reservoir conditions, actual volume/ideal volume
zsc Gas law deviation factor at surface conditions, actual volume/ideal volume (1.0)

Upper Case Letters

B Formation volume factor, reservoir volume/surface volume
Bg Gas formation volume factor, reservoir volume/surface volume (rcf/scf)
Bo Oil formation volume factor, reservoir volume/surface volume (rb/stb)
Bw Water formation volume factor, reservoir volume/surface volume (rb/stb)
M Molar mass, mass/mole
Ma Apparent molar mass of a gas mixture, mass/mole (lbm/lb·mole)
Mair Molar mass of air, mass/mole (28.97 lbm/lb·mole)
Mg Molar mass of gas, mass/mole (lbm/lb·mole)
R Gas-oil ratio, surface gas volume/surface oil volume
Rp Produced gas-oil ratio, surface gas volume/surface oil volume (scf/stb)
Rs Solution gas-oil ratio, surface gas volume/surface oil volume (scf/stb)
T Temperature
V Volume, L3
Vrc Volume at reservoir conditions, L3 (ft3)
Vsc Volume at surface conditions, L3 (ft3)

Greek Letters
γl Liquid specific gravity, density of liquid at 60oF/density of water at 60oF
ρ Mass density, mass/volume
ρg Density, mass/volume (lbm/ft3)
ρl Liquid density, mass/volume (lbm/ft3)
ρo Oil density, mass/volume (lbm/ft3)
ρoR Oil density at reservoir conditions, mass/volume (lbm/ft3)
ρSTO Oil density at surface (stock tank) conditions, mass/volume (lbm/ft3)
ρw Water density, mass/volume (lbm/ft3)

6
Dimension and Unit Systems

Dimensions are physical quantities and units are standards of measurement. Thus, dimensions
are independent of units.

Dimensions are classified as fundamental, supplementary, and derived. Supplementary

dimensions can be considered as fundamental dimensions. Fundamental dimensions are those
necessary to describe a particular field of engineering or science. Derived dimensions are
combinations of fundamental dimensions. A dimensional system is just the smallest number of
fundamental dimensions to form a consistent and complete set for a field of engineering or
science. A dimensional system is called an absolute system if its dimensions are not affected by
gravity; otherwise it is called a gravitational system.

Units are classified as base, supplementary, and derived. Units for supplementary dimensions
can also be considered as base units. Derived units are combinations of base units.

A dimension and unit system is a set of fundamental dimensions and base units necessary for a
particular field of science or engineering. It is called a coherent system if equations between
numerical values (units) have the same form as the corresponding equations between the
quantities (dimensions). For example, in the SI system, F = m·a is used to define the derived
dimension. Likewise, 1 newton = (1 kilogram)·(1 meter per second squared) is used to define
the derived unit. In other words, in a coherent system, combinations of any two unit quantities is
the unit of the resulting quantity. Coherency is a major advantage of the SI system.

In petroleum engineering, three dimension and unit systems are commonly used:

 The International System of Units (SI Units)

 The American Engineering System of Units (Oilfield Units)
 The Darcy System of Units (Darcy Units)

The purpose of these notes is to help you learn the above systems and how to convert units from
one system to another.

7
The International System of Units (SI)

Fundamental Dimension Base Unit

length [L] meter (m)

mass [M] kilogram (kg)
time [t] second (s)
electric current [I] ampere (A)
absolute temperature [T] kelvin (K)
luminous intensity [l] candela (cd)
amount of substance [n] mole (mol)

Supplementary Dimension Base Unit

plane angle [] radian (rad)

solid angle [] steradian (sr)

Derived Dimension Unit Definition

acceleration [L/t2] meter per second squared m/s2

area [L2] square meter m2
Celsius temperature [T ] degree Celsius (oC) K
concentration [n/L3] mole per cubic meter mol/m3
density [M/L3] kilogram per cubic meter kg/m3
electric charge [It] coulomb (C) A·s
electric potential [ML2/It3] volt (V) W/A
electric resistance [ML2/I2t3] ohm () V/A
energy [ML2/t2] joule (J) N·m
force [ML/t2] newton (N) kg·m/s2
frequency [1/t] hertz (Hz) 1/s
molar mass [M/n ] kilogram per mole kg/mol
power [ML2/t3] watt (W) J/s
pressure [M/Lt2] pascal (Pa) N/m2
quantity of heat [ML2/t2] joule (J) N·m
specific heat [L2/t2T] joule per kilogram kelvin J/(kg·K)
thermal conductivity [ML/t3T] watt per meter kelvin W/(m·K)
velocity [L/t] meter per second m/s
viscosity, dynamic [M/Lt] pascal second Pa·s
volume [L3] cubic meter m3
work [ML2/t2] joule (J) N·m

8
The International System of Units (SI) (Cont'd)

Prefix Decimal Symbol

Multiplier

atto 10-18 a
femto 10-15 f
pico 10-12 p
nano 10-9 n
micro 10-6 
milli 10-3 m
centi 10-2 c
deci 10-1 d
deka 10+1 da
hecto 10+2 h
kilo 10+3 k
mega 10+6 M
giga 10+9 G
tera 10+12 T
peta 10+15 P
exa 10+18 E

9
American Engineering System of Units (AES)

Fundamental Dimension Base Unit

length [L] foot (ft)

mass [M] pound mass (lbm)
force [F] pound force (lbf)
time [t] second (sec)
electric charge[Q] coulomb (C)
absolute temperature [T] Rankine (oR)
luminous intensity [l] candela (cd)
amount of substance [n] mole (mol)

Supplementary Dimension Base Unit

plane angle [] radian (rad)

solid angle [] steradian (sr)

Derived Dimension Unit Definition

acceleration [L/t2] foot per second squared ft/sec2

area [L2] square foot ft2
Fahrenheit temperature [T ] degree Fahrenheit (oF) o
R-459.67
concentration [n/L3] mole per cubic foot mol/ft3
density [M/L3] pound mass per cubic foot lbm/ft3
electric current [Q/t] ampere (A) C/sec
electric potential [FL/Q] volt (V) W/A
electric resistance [FLt/Q2] ohm () V/A
energy [FL] foot pound force ft· lbf
frequency [1/t] hertz (Hz) 1/sec
molar mass [M/n ] pound mass per mole lbm/mol
power [FL/t] foot pound force per second ft· lbf/sec
pressure [F/L2] pound force per square foot (psf) lbf/ft2
quantity of heat [FL] british thermal unit (BTU) 777.65 ft· lbf
velocity [L/t] foot per second ft/sec
viscosity, dynamic [Ft/L2] pound force second per square foot lbf·sec/ft2
volume [L3] cubic foot ft3
work [FL] foot pound force ft· lbf

10
Oilfield Units (related to AES System)

Dimension Unit Definition

area [L2] acre (ac) 43,560 ft2

energy [FL] horsepower hour (hp·hr) 1.98000 x 106 ft· lbf
kilowatt hour (kW·hr) 2.6552 x 106 ft· lbf
length [L] inch (in) 1/12 ft
yard (yd) 3 ft
mile (mi) 5,280 ft
mass [M] ounce (oz) 1/16 lbm
ton 2000 lbm
power [FL/t] horsepower (hp) 550 ft· lbf/sec
watt (W) 0.73756 ft· lbf/sec
pressure [F/L2] pound force per square inch (psi) 144 lbf/ft2
atmosphere (atm) 14.696 psi
time [t] minute (min) 60 sec
hour (hr) 3,600 sec
day 86,400 sec
viscosity, dynamic [Ft/L2] centipoise (cp) 10-2 dyne·s/cm2
volume [L3] gallon (gal) 0.133681 ft3
barrel (bbl) 5.614583 ft3
acre·ft (ac·ft) 43,560 ft3

11
Conversion of Units

In a coherent system of units such as SI, a derived dimension is a product or quotient of other
dimensions. For example, the dimension—force—is the product of mass and acceleration,
F = ma, and the unit of force—newton—is the product of the unit of mass and the unit of
acceleration. In the American Engineering System, force is expressed in lb f, mass in lbm, and
acceleration in ft/sec2. This system is obviously not coherent. Hence, a conversion factor other
ma lb m  ft
than one must be used in the equation; that is, F = , where gc = 32.174 2 is a
gc sec  lb f
constant, known as the gravitational conversion constant.

Derivation of gc

The principle of conservation of units is used to derive gc. Briefly stated, this principle is that to
convert a relationship (an equation) from a given system of units to another (a required) system
of units, the given units must be conserved. The technique is illustrated below.

We wish to convert F = ma from SI to AES. Here, SI is the given system and AES is the
required system.

First, find the dimension of the “hidden constant” in the given equation. In other words,

F
1= has dimension force divided by the product of mass and acceleration.
ma

Next, consider the units of the hidden constant—the given units are
2
Ns
2
lb f  sec
and the required units are .
kg  m lb m  ft

Now, convert the given units of the hidden constant to the required units.

Thus,

 0.45359 kg  0.3048 m 

2
1 N  s2 lb f  1 lb f  sec
    =
 kg  m  lb m  ft  4.4482 N  32.174 lb m  ft

12
Review Problems abcdeabcde
1. A weir is a regular obstruction in an open flow
channel over which flow takes place such as that
shown in the sketch at right. It can be used to
measure open channel flow rates. For a rectangular
weir, the theoretical formula for the flow rate is

Q = 5.35LH1.5

where Q is discharge rate in ft3/sec,

L is length of the weir in ft,
H is height of fluid above the crest in ft.

Determine a new constant so the formula can be

applied with Q in m3/s and L and H in m.

2. The ideal gas equation can be written,

pv = RT
where p = pressure, Pa
v = molar volume, m3/(kg·mol)
R = gas constant, 8314.5 Pa·m3/(kg·mol·K)
T = absolute temperature, K
Determine a new constant so that the equation can be applied with p in lb f/in2, v in ft3/(lbm·mol),
and T in oR.

3. The universal law of gravity may be written,

-11 m m
F   6.672 x 10  1 2 2
  r
where F = force of attraction between two bodies, N
m1 = mass of body one, kg
m2 = mass of body two, kg
r = distance between bodies, m
Determine a new constant so that the law can be applied with F in lb f, m1 & m2 in lbm, and r in
mi.

Answers
1. 2.95 m0.5/s
2. 10.732 psi· ft3/(lbm·mol· oR)
3. 1.192 x 10-18 lbf·mi2/lbm2

13
Porosity, Permeability, and Saturation (-k-S)
Porosity is a measure of the fluid storage capacity of a rock,
Vp

Vb

where  = porosity, fraction

Vb = bulk volume = Vp + Vm
Vp = pore volume
Vm = matrix volume

Permeability is a measure of the fluid

conductivity of a rock. It is defined
by Darcy’s law, which is based upon
ex-perimental data. For horizontal,
linear flow of a liquid completely
saturating the rock,
qL
k
Ap

where k = permeability, d
q = flow rate, cm3/s
 = fluid viscosity, cp
L = length of flow path, cm
A = cross-sectional area of
flow path, cm2
p = pressure difference
across
flow path, atm
The dimension of permeability is [L2].

 qL   L3 P  t L 1 1 
 Ap    t  1  1  2  P 
   L 

Saturation is a measure the amount and type of fluid stored in a rock.

V
S 
Vp

where S = saturation of fluid  (oil, water, or gas)

V = fluid volume (  = oil, water, or gas)
Vp = pore volume

14
Darcy’s Law
Darcy found that when water flows
vertically downward through sand, the
volume of water passing through the
system in unit time (the discharge q in
Fig. 2) is proportional to the drop in
head h across the sand. Considering
the cross sectional area A and thick-
ness of the sand l, these observations
can be written,
q dh
v  K
A dl

where K is a coefficient depending

upon the permeability of the sand and
the properties of the fluid.
Darcy’s original experiment has been
extended to answer questions about
flow of different fluids in porous
media of various permeabilities along
flow paths in various directions.

The generalized two dimensional form of Darcy’s law (API Code 27) is

k  dp g dz 6 
vs     x 10 
  ds 1.01325 ds 

where s = distance in direction of flow (always positive), cm

vs = volume flux across a unit area of the porous medium in unit time (q/A)
along flow path s, cm/s
z = vertical coordinate (positive downward), cm
 = density of the fluid, g/cm3
g = acceleration of gravity, 980.665 cm/s2
dp/ds = pressure gradient along path s at the point to which vs refers, atm/cm
 = viscosity of the fluid, cp
k = permeability of the porous medium, d

15
The Darcy System of Units

Fundamental Dimension Base Unit

length [L] centimeter (cm)

mass [M] gram (g)
time [t] second (s)

Derived Dimension Unit Definition

acceleration [L/t2] centimeter per second squared cm/s2

area [L2] square centimeter cm2
density [M/L3] gram per cubic centimeter g/cm3
energy [ML2/t2] erg dyne·cm
force [ML/t2] dyne g·cm/s2
permeability [L2] darcy (d) cp·cm2/atm·s
pressure [M/Lt2] atmosphere (atm) 1.013250 x 106 dyne/cm2
velocity [L/t] centimeter per second cm/s
viscosity, dynamic [M/Lt] centipoise (cp) 10-2 dyne·s/cm2
volume [L3] cubic centimeter cm3
work [ML2/t2] erg dyne·cm

In SI Units

Derived Dimension Unit

permeability [L2] square meter (m2)

In Oilfield Units

Derived Dimension Unit

permeability [L2] millidarcy (md)

16
Converting Permeability Units
The principle of conservation of units is used. Briefly stated, this principle is that to convert a
relationship (an equation) from a given system of units to another (a required) system of units,
the given units must be conserved. The technique is illustrated below.
qL
We wish to convert k from Darcy units (d, cm, s, cp, atm) to Oilfield units (md, ft, bbl,
Ap
day, cp, psi). Here, Darcy units is the given system and Oilfield units is the required system.

First, find the dimension of the “hidden constant” in the given equation. In other words,
kAp
1= has dimension kAp divided by qL [1].
qL
Next, consider the units of the hidden constant—the given units are
d  atm  s md  ft  psi  day
2 and the required units are .
cp  cm cp  bbl
Now, convert the given units of the hidden constant to the required units.

Thus,

 1 d  atm  s  10 md  ft  14.696 psi  day   30.48  cm 

3 2 2

 
 
  
 
 =
 cp  cm  d  ft  atm  86,400 s  
2 2
ft 

 158.02 md  ft  psi  day  5.614583 ft  887.22 md  ft  psi  day

3

   
 cp  ft 3  bbl  cp  bbl

Converting from Darcy units to other systems of units is similar.

Summary of Darcy equations for horizontal, linear flow (including conversion factors):
Darcy Units SI Units Oilfield Units
qL qL qL
k k k  887.2
Ap Ap Ap

NOTE: A m2 is a huge permeability unit! There are 1.01325 x 1012 d/m2.

Thus, the SPE preferred SI unit for permeability is a m2, introducing
a factor of 10 12 in the equation.

17
Horizontal, Linear Flow

A
q q

x1 x2

Applying Darcy’s law,

q k dp
vx  
A  dx

Separate the variables and integrate to obtain the flow equation,

x2 kA p 2 3 kA p 2  p1  kA p1  p 2  kAp

q  dx    dp  q (cm / s)    
x1  p  x 2  x 1   x 2  x 1  L
1

In oilfield units, the equation is

1.1271 x 10 3 kAp 1.1271 x 10 3 kAp

q (RB / day)  or q (STB / day) 
L BL

EXAMPLE: A rock sample10 cm long and 2 cm2 in cross section is used for some steady-state
flow tests. Calculate the permeability of the rock if it is completely saturated with
an oil having a viscosity of 2.5 cp and oil is flowed through the rock at a rate of
0.0080 cm3/s under a 1.5 atm pressure drop?

k
qL

 
0.0080 cm 3 / s  2.5 cp 10 cm 
 0.067 d  67 md
Ap  
2 cm 2 1.5 atm 

18
Wellbore Volumes

Wellbores are right circular cylinders,

the volume of which is,

V  r h   d h
2 2
h
4

Many drilling and completion applications

require the annular volume,

   
V   r22  r12 h   d 22  d12 h
4

EXAMPLE: Suppose you are the drilling engineer on a rig. You have set 7-5/8 inch OD,
33.7 lbm/ft casing (ID = 6.765 inches) from 0 to 5900 ft and have drilled out to
7900 ft. The average bore hole diameter from 5900 to 7900 ft is 6.25 inches.
Calculate the annular volume in ft 3 if 4-1/2 inch OD casing is installed.

 6.765 in  2  4.5 in  2   6.25 in  2  4.5 in  2  

 
V        5900 ft        2000 ft 
4  12 in / ft   12 in / ft 
   12 in / ft 12 in / ft 

      


V = 987 ft3

19
 Pressure Gradients
The basic equation of hydrostatics can be written
p = gh
where p = change in fluid pressure, Pa
 = density, kg/m3
g = acceleration of gravity, m/s2
h = change in height of fluid, m

The pressure gradient (Pa/m) is

p
 g
h

There is no conversion factor in SI because

 Pa kg m N 1 Pa 
 m  m 3  s 2  m 2  m  m 

In oilfield units, p = change in fluid pressure, lbf/in2 or psi

 = density, lbm/ft3
g = acceleration of gravity, ft/s2
h = change in height of fluid, ft
and the pressure gradient (psi/ft) is
p g lb m  ft
 ,where g c  32.174 2
h 144g c lb f  s

Notice that the units check because

 psi lbm ft ft 2 lb f  s 2 lb f 1 psi 

 ft  ft 3  s 2  in 2  lb  ft  in 2  ft  ft 
 f 

EXAMPLE: Calculate the pressure gradient for a fluid having a density of 65 lb m/ft3.
Assume g = 32 ft/s2.

p

g

 65 32   0.449 or 0.45 psi / ft
h 144g c  144 32.174

20
Horizontal, Radial Flow

ds = -dr

h
rw re

Applying Darcy’s law,

q q k dp
vr   
A 2 rh  dr

Separate the variables and integrate to obtain the flow equation,

re dr 2kh p e
3 2kh  p e  p w  2khp
q    dp  q (cm / s)  
rw r  p
w
 ln re r w  
 ln re r w  
In oilfield units, the equation for liquid is

7.0819 x 10 3 khp 7.0819 x 10 3 khp

q  (RB / day)  or q  (STB / day) 
 
 ln re r w B  ln re r w  
and, the equation for gas is

7.0819 x 10 3 khp 7.0819 x 10 3 khp

q g (RB / day)  or q g (Scf / day) 

 ln re r w 
B g ln re r w 

21
Reservoir Volumes

h
rw re

The volume occupied by the reservoir rock or bulk volume is

2
Vb  re h

Since porosity is the ratio of the pore volume to bulk volume, the pore volume is
2
Vp  re h

And, since water saturation is the fraction of the pore volume filled with water, the hydrocarbon
pore volume is
Vhc  re h 1 S w 
2

A commonly used equation to calculate the surface volume of oil in place is

7758Ah1  S w 
N(STB)  , where A is the drainage area in acres.
Bo

and the surface volume of gas in place is

7758Ah1  S w 
G(Scf)  , where B g is the gas formation volume factor in RB / Scf .
Bg

22
Homework Problems
1. A certain oilfield has an average producing gas-oil ratio of 350 scf/stb. The density of the stock
tank oil is 54.7 lbm/ft3 at 60 oF and the apparent molar mass of the associated gas is 21.7
lbm/lbmole. Determine the
a. API gravity of the stock tank oil.
b. Specific gravity of the associated gas.
c. Density of the reservoir oil if the oil formation volume factor is 1.2 rb/stb and the gas in
solution is equal to the average producing gas-oil ratio.
d. Type of reservoir fluid.

2. The equation of state for a particular substance at low pressures can be written

p = 53.55T,
where p = pressure, lbf/ft2
= density, lbm/ft3
T = absolute temperature, oR

a. Determine a new constant so the equation can be used with p in Pa,  in kg/m3, and T in K.
b. Use the ideal gas law (pV = nRT), the definition of quantity (mass/molar mass), and the
definition of density (mass/volume) to identify the substance.

3. Power is defined as work per unit time.

a. Find the units of the hidden constant in P = W/t (SI system), where P is power in
watts, W is work in newton-meters, and t is in seconds.
b. Convert to constant to the AES system, where P is power in horsepower, W is work in
foot-pounds of force, and t is in minutes.

4. A cylindrical sandstone sample, one inch in diameter and one inch long has a pore volume of 0.275
in3. The pores are partially filled with 0.135 in 3 of water. What is the porosity and water saturation of
the sample?

5. A cylindrical sandstone sample, one inch in diameter and one inch long is placed in a permeameter
and water having a viscosity of one centipoise is flowed through the circular faces of the sample at a rate
of one cm3/s under a pressure difference of one atmosphere. What is the permeability of the sample?

6. An acre-ft of reservoir has a bulk volume of 43,560 ft 3. Calculate the volume of water (in barrels per
acre-ft) for a sandstone reservoir having a porosity of 20 % and a water saturation of 25 %.

7. A rock sample is 1 inch long and 1 inch in diameter. The sample is used for some steady-state flow
tests. Calculate the permeability of the rock if it is completely saturated with water having a viscosity of
1 cp and water is flowed through the sample at a rate of 0.5 in 3/min and the pressure drop is 10 psi.

8. Find the conversion constant to calculate permeability in md from a horizontal, linear flow experiment
when flow rate is in cm3/s, viscosity is in cp, length is in cm, and pressure drop is in dynes/cm 2.

9. Find the conversion constant to calculate permeability in md from a horizontal, linear flow experiment
when flow rate is in m3/day, viscosity is in cp, length is in m, and pressure drop is in kPa.

23
10. Suppose you are the drilling engineer on a rig. You have set 9 5/8 in OD, 40 lb m/ft casing (ID =
8.835 in) from 0 to 2000 ft and have drilled a 7 7/8 in bore hole from 2000 to 4000 ft.

a. Find the capacity of the hole in barrels from 0 to 4000 feet.

b. The hydrostatic pressure at 4000 ft with fresh water in hole.
c. The annular volume if 4.5 inch OD, 11.60 lb m/ft casing is installed from 0 to 4000 ft
with fresh water in hole.

11. Find the conversion constant to calculate pressure gradient in psi/ft when fluid density is in lb m/gal
(ppg)

12. A vertical gas well is 6000 ft deep.

a. What is its bottom hole temperature if the mean surface temperature is 60 oF and the
local temperature gradient is 1.1 oF/100 ft?
b. What is its bottom hole flowing pressure if the surface flowing pressure is 900 psi
and the pressure gradient in the well bore is 0.15 psi/ft?

13. Assume a vertical well drains a right cylindrically shaped oil reservoir for which you have the
following data:

drainage area 40 acres (external radius = 745 ft)

formation thickness 25 feet
radius of well bore 0.25 feet
porosity 19 %
water saturation 21 %
permeability 75 millidarcy
oil viscosity 2.1 centipoise
pressure at external radius 3545 psi
pressure at the well bore radius 1515 psi

Calculate the initial production rate in reservoir barrels per day.

14. Given the following data on a gas reservoir:

porosity 0.22
water saturation 0.30
gas formation volume factor 1.0 rb/MScf

a. Calculate the volume of gas in MScf per acre-foot of reservoir volume.

b. If the recovery factor is 80 %, what is the recoverable reserve of a 160 acre spaced well
with an average reservoir thickness of 15 feet?

24
Problem Layout

25
Conversion Factors
To convert from Multiply by To obtain
acres 4.356 x 104 sq feet
acres 4.047 x 103 sq meters
acre-feet 4.356 x 104 cubic feet
atmospheres 7.6 x 101 cm of mercury at 0 oC
atmospheres 3.39 x 101 ft of water at 4 oC
atmospheres 1.01325 x 105 pascals
atmospheres 1.4696 x 101 pounds-force/sq in
barrels(oil) 5.614583 cubic feet
barrels(oil) 4.2 x 101 gallons
barrels(oil)/d 2.295 x 10-3 cubic meters/s
Btu 1.0550 x 1010 ergs
Btu 7.7816 x 102 ft-pounds
Btu 3.927 x 10-4 horsepower-hours
Btu 1.055 x 103 joules
Btu 2.928 x 10-4 kilowatt-hours
centimeters 3.281 x 10-2 feet
centimeters 3.937 x 10-1 inches
centimeters 6.214 x 10-6 miles
cm of mercury 1.316 x 10-2 atmospheres
cm of mercury 4.461 x 10-1 ft of water
cm of mercury 1.333 x 103 pascals
cm of mercury 1.934 x 10-1 pounds-force/sq in
cm/s 1.969 ft/min
cm/s 3.281 x 10-1 ft/s
cm/s 3.6 x 10-2 kilometers/h
cm/s 2.237 x 10-2 miles/h
centipoise 1.0 x 10-3 pascal-seconds
cubic cm 6.28982 x 10-6 barrels(oil)
cubic cm 3.531 x 10-5 cubic ft
cubic cm 2.642 x 10-4 gallons
cubic cm 1.0 x 10-3 liters
cubic cm/s 5.434 x 10-1 barrels(oil)/d
cubic feet 1.781 x 10-1 barrels(oil)
cubic feet 2.832 x 10-2 cubic meters
cubic feet 7.48052 gallons
cubic feet 2.832 x 101 liters
cubic ft/d 3.278 x 10-7 cubic meters/s
cubic feet/h 4.275 barrels(oil)/d
cubic feet/min 4.720 x 10-1 liters/s
cubic feet/s 4.48831 x 102 gallons/min
cubic meters 6.28982 barrels(oil)
cubic meters 3.531 x 101 cubic ft

26
To convert from Multiply by To obtain
cubic meters 2.642 x 102 gallons
cubic meters 1.0 x 103 liters
cubic meters/s 5.434 x 105 barrels(oil)/d
darcies 9.869233 x10-13 sq meters
dynes/sq cm 9.869233 x 10-7 atmospheres
dynes 1.0 x 10-5 joules/meter (newtons)
dynes 2.248 x 10-6 pounds-force
ergs 9.486 x 10-11 Btu
ergs 7.376 x10-8 ft-pounds
ergs 1.0 x 10-7 joules
ergs 2.773 x 10-14 kilowatt-hrs
ergs/s 1.341 x 10-10 horsepower
feet 3.048 x 10-4 kilometers
feet 3.048 x 10-1 meters
feet 1.894 x 10-4 miles
feet of water 2.950 x 10-2 atmospheres
feet of water 2.242 cm of mercury
feet of water 2.989 x 103 pascals
feet of water 4.335 x 10-1 pounds-force/sq in
feet/min 1.829 x 10-2 km/hr
feet/min 3.048 x 10-1 meters/min
feet/min 1.136 x 10-2 miles/h
feet/s 1.097 km/h
feet/s 1.829 x 101 meters/min
feet/s 6.818 x 10-1 miles/h
feet/s2 3.048 x 10-1 meters/s2
foot-pounds 1.286 x 10-3 Btu
foot-pounds 1.356 x 107 ergs
foot-pounds 1.356 joules
foot-pounds 1.383 x 10-1 kg-m
foot-pounds 3.766 x 10-7 kilowatt-h
foot-pounds/min 1.286 x 10-3 Btu/min
foot-pounds/min 3.030 x 10-5 horsepower
foot-pounds/min 2.260 x 10-5 kilowatts
foot-pounds/s 4.6263 Btu/h
foot-pounds/s 1.818 x 10-3 horsepower
foot-pounds/s 1.356 x 10-3 kilowatts
gallons 2.381 x 10-2 barrels(oil)
gallons 1.337 x 10-1 cubic ft
gallons 3.785 x 10-3 cubic meters
gallons 3.785 liters
gallons/min 2.228 x 10-3 cu ft/s
grams 2.205 x 10-3 pounds-mass
horsepower 4.244 x 101 btu/min

27
To convert from Multiply by To obtain
horsepower 3.3 x 104 ft-lb/min
horsepower 5.50 x 102 ft-lb/s
horsepower 7.457 x 10-1 kilowatts
horsepower-hours 2.547 x 103 Btu
horsepower-hours 1.98 x 106 ft-lb
horsepower-hours 2.684 x 106 joules
inches 2.540 centimeters
inches 2.540 x 10-2 meters
joules 9.486 x 10-4 Btu
joules 7.376 x 10-1 ft-pounds
joules/s 5.6907 x 10-2 Btu/min
kilograms 2.2046 pounds-mass
kilograms/cu m 6.243 x 10-2 pounds-mass/cu ft
kilometers 3.281 x 103 ft
kilometers 6.214 x 10-1 miles
kilometers/h 5.468 x 101 ft/min
kilometers/h 9.113 x 10-1 ft/s
kilometers/h 6.214 x 10-1 miles/h
kilowatts 1.341 horsepower
kilowatt hour 3.413 x 103 Btu
kilowatt hour 2.655 x 106 ft-lb
kilowatt hour 3.6 x 106 joules
liters 1.0 x 103 cubic cm
liters 3.531 x 10-2 cubic ft
liters 1.0 x 10-3 cubic meters
liters 2.642 x 10-1 gallons
liters/s 1.5850 x 101 gallons/min
meters 3.281 ft
meters 3.937 x 101 inches
meters 6.214 x 10-4 miles
meters 1.094 yards

28
meters/s 1.968 x 102 ft/min
meters/s 3.281 ft/s
meters/s 3.6 km/h
meters/s 2.237 miles/h
miles 5.280 x 103 ft
miles 1.609 kilometers
miles 1.609 x 103 meters
miles/h 8.8 x 101 ft/min.
miles/h 1.467 ft/s
miles/h 1.6093 km/h
miles/h 2.682 x 101 meters/min
newtons 1.0 x 105 dynes
pounds-force 4.4482 x 105 dynes

To convert from Multiply by To obtain

pounds-force 4.4482 newtons
pounds-mass 4.5359 x 102 grams
pounds-mass 4.5359 x 10-1 kilograms
pounds-mass/cu ft 1.602 x 101 kg/cu m
pounds-force/sq ft 4.725 x 10-4 atmospheres
pounds-force/sq ft 1.602 x 10-2 ft of water
pounds-force/sq ft 4.788 x 10 pascals
pounds-force/sq in 2.307 ft of water
pounds-force/sq in 5.171 cm of mercury
pounds-force/sq in 6.895 x 103 pascals
radians 5.7296 x 101 degrees
radians/s 9.5493 revolutions/min
revolutions/min 1.047 x 10-1 radians/s
square cm 1.076 x 10-3 sq ft
square feet 2.296 x 10-5 acres
square feet 9.29 x 10-2 sq m
square feet 3.587 x 10-8 sq miles
square meters 2.471 x 10-4 acres
square meters 1.076 x 101 sq ft
square meters 3.861 x 10-7 sq miles
square miles 2.788 x 107 sq ft
square miles 2.590 x 106 sq meters
watts 3.4129 Btu/h
watts 1.0 x 107 ergs/s
watts 4.427 x 101 ft-lb/min
watts 7.376 x 10-1 ft-lb/s
watts 1.341 x 10-3 horsepower
watt hours 3.413 Btu
watt hours 2.656 x 103 ft-pounds

29
30