Scribd
Upload
225 views

Soldering Safety Guidelines

1. Soldering involves heating elements to high temperatures and risks of burns, fumes, and fires. Proper safety equipment like gloves, ventilation, and fire extinguishers are required. 2. Lead exposure from solder is hazardous to health and lead-free solder should be used. Fumes from solder and flux can irritate eyes and lungs so work should be done in a well-ventilated area. 3. Precautions like returning hot irons to stands, avoiding touching hot elements, and allowing joints to cool reduce burn risks. Proper soldering technique helps form strong connections safely.

Uploaded by

Tyler Roses
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
225 views

Soldering Safety Guidelines

1. Soldering involves heating elements to high temperatures and risks of burns, fumes, and fires. Proper safety equipment like gloves, ventilation, and fire extinguishers are required. 2. Lead exposure from solder is hazardous to health and lead-free solder should be used. Fumes from solder and flux can irritate eyes and lungs so work should be done in a well-ventilated area. 3. Precautions like returning hot irons to stands, avoiding touching hot elements, and allowing joints to cool reduce burn risks. Proper soldering technique helps form strong connections safely.

Uploaded by

Tyler Roses
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

SOLDERING SAFETY GUIDELINES

GENERAL SOLDERING SAFETY NOTES


1. Never touch the element or tip of the soldering iron. They are very hot (about 400°C) and will
burn. The solder itself also gets hot.
2. Hold wires to be heated with tweezers or clamps.
3. Keep the cleaning sponge wet during use.
4. Always return the soldering iron to its stand when not in use. Never put it down on your
workbench. Be sure that the stand is weighted enough or attached to your work table so that it
doesn’t topple over if you brush against the cord.
5. Turn the unit off or unplug it when not in use.
6. Soldering irons come in models that use different wattages. Use the right size soldering iron
for your projects; too much heat can ruin your board or components.
7. Never, ever try to catch a hot soldering iron if you drop it. Let it fall, buy a new one if you have
to just don’t grab it!
8. Give any soldered surface a minute or two to cool down before you touch it.

WORK SAFELY WITH SOLDER, FLUX AND CLEANERS


1. Wear eye protection. Solder can “spit” (an air pocket or impurity can pop as you heat the
solder and send bits of solder flying).
2. Use lead free solder.
3. Keep cleaning solvents in dispensing bottle to reduce inhalation hazards.
4. Always wash your hands with soap and water after soldering.
5. Read and understand the MSDS (Material Safety Data Sheets) for all materials before
beginning work (e.g., http://jr.chemwatch.net/chemwatch.web/account/login).

DANGERS OF LEAD EXPOSURE


Lead (http://www.cdc.gov/niosh/topics/lead/) on your skin can be ingested and lead fumes can
be given off during soldering. Other metal (https://www.osha.gov/SLTC/metalsheavy/index.html)
fumes can also be hazardous. Lead can have serious chronic health effects, such as
reproductive problems, digestive problems, nerve disorders, memory and concentration
problems, muscle and joint pain.

AVOID TOXIC FUMES


1. Work in a well‐ventilated area, to prevent the mildly caustic and toxic fumes from building up
and causing eye or throat irritation.. The smoke formed is mostly from the flux which can be
irritating, a sensitizer and aggravates asthma. Avoid breathing it by keeping your head to the
side of, not above, your work.
2. A benchtop fume extractor may be necessary to remove harmful fumes caused by solder and
flux from the soldering workstation by filtering the air. If the lab is equipped with a snorkel fume
extractor, always use it when soldering.

REDUCE RISK FROM ELECTRICITY


1. Always use a grounded outlet and grounding prong to reduce the risk of electrical damage if
a short circuit occurs in the equipment.
2. Prevent damage to electrical cords during soldering. Keep them away from heated tips.
3. Never solder a live circuit (one that is energized).

FIRE PREVENTION
1. Work on a fire‐proof or nonflammable surface that is not easily ignited.
2. Never place a hot soldering iron on your work surface: you could start a fire. Never leave
flammable items (such as paper) near your soldering iron.
3. Wear nonflammable or 100% cotton clothing that covers your arms and legs to help prevent
burns.
4. Know where your fire extinguisher is and how to use it.

RECOMMENDED PROCEDURE

1. Turn on the fume extractor


2. Put on safety goggles
3. Make sure the iron is in the stand. Always return the soldering iron to its stand when not in
use.
4. Turn on the main switch to the iron (never touch the tip of the iron)
5. Dampen the sponge in the stand
6. Wipe the tip of the iron on the damp sponge to clean the tip.
7. Melt a little solder on the tip of the iron. This 'tinning' will help the heat to flow from the iron's
tip to the joint. This is necessary when you first turn on the iron and occasionally while soldering
if you need to wipe the tip clean on the sponge.
8. Hold the soldering iron like a pen, near the base of the handle. Imagine you are going to write
your name! DO NOT touch the hot element or tip.
9. Touch the soldering iron onto the joint to be made. Make sure it touches both the component
lead and the track. Hold the tip there for a few seconds.
10. Feed a little solder onto the joint. It should flow smoothly onto the lead and track to form a
volcano shape. Apply the solder to the joint, not the iron.
11. Remove the solder, then the iron, while keeping the joint still. Allow the joint a few seconds
to cool before you move the circuit board.
12. Remember to return the iron to the stand.
13. Inspect the joint closely. It should look shiny and have a 'volcano' shape. If not, you will need
to reheat it and feed in a little more solder. This time ensure that both the lead and track are
heated fully before applying solder.
14. Switch off the power to the iron after use
Soldering | Environmental Health and Safety (stonybrook.edu)

Safe Soldering Techniques – Environment, Health, and Safety (mit.edu)

Soldering Safety | Home-made robots | Electrical engineering | Khan Academy - Bing video

How to Solder Wires Together (Best tips and tricks) - Bing video

Soldering_Safety_Guidelines.pdf (tntech.edu)

Safe Soldering Work Practices (hvcc.edu)

You might also like