06/12/2014

Bank: (Aviation Mechanic General)

Airman Knowledge Test Question Bank

The FAA computer-assisted testing system is supported by a series of supplement publications.

These publications, available through several aviation publishers, include the graphics, legends,
and maps that are needed to successfully respond to certain test items. Use the following URL to
download a complete list of associated supplement
books: http://www.faa.gov/pilots/testing/supplements/

The Learning Statement Reference Guide for Airman Knowledge Testing contains listings of
learning statements with their associated codes. It can be located
at: http://www.faa.gov/training_testing/testing/media/LearningStatementReferenceGuide.pdf

1. AMG102 AMG
Convert farads to picofarads by:
A) Multiply farads by 10 to the power of 12
B) Multiply microfarads by 10 to the power of-12
C) Multiply picofarads by 10 to the power of 12

2. AMG031 AMG
The opposition offered by a coil to the flow of alternating current is called (disregard resistance)
A) impedance.
B) reluctance.
C) inductive reactance.

3. AMG102 AMG
In a parallel circuit with three 6-ohms resistors across a 12-volt battery, what is the total current (It)
value in the circuit?
A) 2 amps.
B) 6 amps.
C) 12 amps.

4. AMG102 AMG
In a parallel circuit with four 6-ohms resistors across a 24-volt battery, what is the total voltage across
resistor-three (VR3) in the circuit?
A) 6 volts.
B) 18 volts.
C) 24 volts.

5. AMG015 AMG
Which statement is correct when made in reference to a parallel circuit?
A) The current is equal in all portions of the circuit.
B) The total current is equal to the sum of the currents through the individual branches of the circuit.
C) The current in amperes can be found by dividing the EMF in volts by the sum of the resistors in
ohms.

6. AMG102 AMG
What is the opposition to the flow of AC produced by a magnetic field with generated back voltage
(EMF) called?
A) Inductive reactance.
B) Capacitive reactance.
C) Mutual inductance.

7. AMG042 AMG
Through which material will magnetic lines of force pass the most readily?
A) Copper.
B) Iron.
C) Aluminum.

8. AMG031 AMG
Electrostatic fields are also known as
A) dielectric fields.
B) electrostatic fields.
C) static fields.

9. AMG031 AMG
Which of the following are commonly used as rectifiers in electrical circuits?
1. Anodes.
2. Cathodes.
3. Diodes.
A) 3, 1.
B) 3, 2.
C) 3.

10. AMG015 AMG

What is the operating resistance of a 30-watt light bulb designed for a 28-volt system?
A) 1.07 ohms.
B) 26 ohms.
C) 0.93 ohm.

11. AMG015 AMG

A 48-volt source is required to furnish 192 watts to a parallel circuit consisting of three resistors of equal
value. What is the value of each resistor?
A) 36 ohms.
B) 4 ohms.
C) 12 ohms.

12. AMG031 AMG

A lead acid battery with 12 cells connected in series (no load voltage = 2.1 volts per cell) furnishes 10
amperes to a load of 2 ohms resistance. The internal resistance of the battery in this instance is
A) 0.52 ohm.
B) 2.52 ohms.
C) 5.0 ohms.

13. AMG031 AMG

Nickel-cadmium batteries which are stored for a long period of time will show a low liquid level because
A) electrolyte evaporates through the vents.
B) of current leakage from individual cells.
C) electrolyte becomes absorbed into the plates.

14. AMG031 AMG

Which of the following best describes the contributing factors to thermal runaway in a nickel-cadmium
battery installed in an aircraft?
A) High internal resistance intensified by high cell temperatures and a high current discharge/charge
rate in a constant potential (voltage) charging system.
B) Low internal resistance intensified by high cell temperatures and a high voltage discharge/charge
rate in a constant current charging system.
C) Low internal resistance intensified by high cell temperatures and a high current discharge/charge
rate in a constant potential (voltage) charging system.

15. AMG015 AMG

What is the likely result of servicing and charging nickel-cadmium and lead acid batteries together in
the same service area?
A) Lowered amp-hour capacities for both types of batteries.
B) Reduced battery service life for both types of batteries.
C) Contamination of both types of batteries.

16. AMG031 AMG

What is the basic unit of electrical quantity?
A) Electromotive Force
B) Ampere
C) Coulomb

17. AMG015 AMG

What will a voltmeter read if properly connected across a closed switch in a circuit with electrical power
on?
A) Voltage drop in the component(s) the switch is connected to.
B) System voltage.
C) Zero voltage.
18. AMG031 AMG
What is defined as a group of bits representing a complete piece of information?
A) Byte.
B) Bit.
C) Word.

19. AMG031 AMG

Convert the binary number 1111 to decimal form.
A) 14.
B) 15.
C) 16.

20. AMG102 AMG

Which of the following logic gates will provide an active high out only when all inputs are different?
A) NAND.
B) NOR.
C) XOR.

21. AMG015 AMG

When referring to an electrical circuit diagram, what point is considered to be at zero voltage?
A) The circuit breaker.
B) The ground reference.
C) The switch.

22. AMG015 AMG

(Refer to General figure 19.) When the throttles are retarded with only the right gear down, the warning
horn will not sound if an open occurs in wire
A) No. 5.
B) No. 13.
C) No. 6.

23. AMG001 AMG

1. Sketches are usually made with the aid of drafting instruments.
2. Sketches are usually more complicated to make when using graph paper.
Regarding the above statements:
A) Only No. 1 is true.
B) Only No. 2 is true.
C) Neither No. 1 nor No. 2 is true.

24. AMG001 AMG

(1) According to 14 CFR Part 91, repairs to an aircraft skin should have a detailed dimensional sketch
included in the permanent records.
(2) On occasion, a mechanic may need to make a simple sketch of a proposed repair to an aircraft, a
new design, or a modification.
Regarding the above statements,
A) only No. 1 is true.
B) only No. 2 is true.
C) both No. 1 and No. 2 are true.

25. AMG014 AMG

What numbering system is used to locate fuselage frames?
A) Zone numbers.
B) Station numbers.
C) Tolerances.

26. AMG013 AMG

In a sectional view drawing, what sections illustrate particular parts of an object?
A) Removed.
B) Revolved.
C) Half.

27. AMG014 AMG

What type of line is normally used in a mechanical drawing or blueprint to represent an edge or object
not visible to the viewer?
A) Medium weight dashed line.
B) Medium solid line.
C) Alternate short and long light dashes.

28. AMG014 AMG

What is used to indicate that a surface must be machine finished?
A) Tolerances.
B) Leader lines.
C) Finished marks.

29. AMG016 AMG

(Refer to General figure 41.) Determine the fuel consumption with the engine operating at cruise, 2,350
RPM.
A) 49.2 pounds per hour.
B) 51.2 pounds per hour.
C) 55.3 pounds per hour.

30. AMG002 AMG

If an aircraft CG is found to be at 24 percent of MAC, that 24 percent is an expression of the
A) distance from the TEMAC.
B) distance from the LEMAC.
C) average distance from the LEMAC to the wing center of lift.

31. AMG002 AMG

Which statement is true regarding helicopter weight and balance?
A) Regardless of internal or external loading, lateral axis cg control is ordinarily not a factor in
maintaining helicopter weight and balance.
B) The moment of tail-mounted components is subject to constant change.
C) Weight and balance procedures for airplanes generally also apply to helicopters.

32. AMG003 AMG

Maximum zero fuel weight is the
A) dry weight plus the weight of full crew, passengers, and cargo.
B) basic operating weight without crew, fuel, and cargo.
C) maximum permissible weight of a loaded aircraft (passengers, crew, and cargo) without fuel.

33. AMG002 AMG

What determines whether the value of a moment is preceded by a plus (+) or a minus (-) sign in aircraft
weight and balance?
A) The location of the weight in reference to the datum.
B) The result of a weight being added or removed and its location relative to the datum.
C) The location of the datum in reference to the aircraft CG.

34. AMG002 AMG

When an aircraft is positioned for weighing on scales located under each landing gear wheel, which of
the following may cause erroneous scale readings?
A) Gear downlocks installed.
B) Parking brakes set.
C) Parking brakes not set.

35. AMG002 AMG

Use of which of the following generally yields the highest degree of aircraft leveling accuracy?
A) Electronic load cell(s).
B) Spirit level(s).
C) Plumb bob and chalk line.

36. AMG017 AMG

Which statement(s) about Military Standard (MS) flareless fittings is/are correct?
1. During installation, MS flareless fittings are normally tightened by turning the nut a specified amount,
rather than being torqued.
2. New MS flareless tubing/fittings should be assembled clean and dry without lubrication.
3. During installation, MS flareless fittings are normally tightened by applying a specified torque to the
nut.
A) 1.
B) 1 and 2.
C) 3.

37. AMG037 AMG

When a Teflon hose has been in service for a time, what condition may have occurred and/or what
precaution should be taken when it is temporarily removed from the aircraft?
A) The hose interior must be kept wet with the fluid carried to prevent embrittlement/deterioration.
B) The hose may become stiff and brittle if not flexed or moved regularly.
C) The hose may have developed a set, or have been manufactured with a pre-set shape, and must be
supported to maintain its shape.

38. AMG036 AMG

The best tool to use when cutting aluminum tubing, or any tubing of moderately soft metal is a
A) hand operated wheel-type tubing cutter.
B) fine-tooth hacksaw.
C) circular-saw equipped with an abrasive cutting wheel.

39. AMG036 AMG

If a flared tube coupling nut is overtightened, where is the tube most likely to be weakened/damaged?
A) Along the entire length of the sleeve and tube interface.
B) At the edge of the sleeve and straight portion of the tube.
C) At the sleeve and flare junction.

40. AMG020 AMG

What is generally used in the construction of aircraft engine firewalls?
A) Stainless steel.
B) Chrome molybdenum alloy steel.
C) Titanium nickel alloy.

41. AMG017 AMG

A particular component is attached to the aircraft structure by the use of an aircraft bolt and a castle
tension nut combination. If the cotter pin hole does not align within the recommended torque range, the
acceptable practice is to
A) exceed the recommended torque range by no more than 10 percent.
B) tighten below the torque range.
C) change washers and try again.

42. AMG017 AMG

Unless otherwise specified, torque values for tightening aircraft nuts and bolts relate to
A) clean, dry threads.
B) clean, lightly oiled threads.
C) both dry and lightly oiled threads.

43. AMG066 AMG

A Technical Standard Order (T.S.O.) is issued by whom?
A) The Aircraft industry.
B) Part manufactures.
C) The Administrator.
44. AMG045 AMG
When towing a large aircraft
A) a person should be in the cockpit to watch for obstructions.
B) persons should be stationed at the nose, each wingtip, and the empennage at all times.
C) a person should be in the cockpit to operate the brakes.

45. AMG045 AMG

A person should approach or leave a helicopter in the pilot's field of vision whenever the engine is
running in order to avoid
A) the tail rotor.
B) the main rotor.
C) blowing dust or debris caused by rotor downwash.

46. AMG045 AMG

If a radial engine has been shut down for more than 30 minutes, the propeller should be rotated through
at least two revolutions to
A) check for hydraulic lock.
B) check for leaks.
C) prime the engine.

47. AMG095 AMG

During starting of a turbine powerplant using a compressed air starter, a hung start occurred. Select the
proper procedure.
A) Advance power lever to increase RPM.
B) Re-engage the starter.
C) Shut the engine down.

48. AMG012 AMG

Why is it important not to rotate the crankshaft after the corrosion preventive mixture has been put into
the cylinders on engines prepared for storage?
A) Engine damage can occur from hydraulic lock.
B) Fuel may be drawn into one or more cylinders and dilute or wash off the corrosion preventive
mixture.
C) The seal of corrosion preventive mixture will be broken.

49. AMG044 AMG

The total piston displacement of a specific engine is
A) dependent on the compression ratio.
B) the volume displaced by all the pistons during one revolution of the crankshaft.
C) the total volume of all the cylinders.

50. AMG044 AMG

A rectangular shaped fuel tank measures 37-1/2 inches in length, 14 inches in width, and 8-1/4 inches
in depth. How many cubic inches are within the tank?
A) 59.75
B) 433.125
C) 4,331.25

51. AMG053 AMG

Find the cube of 64.
A) 4.
B) 192.
C) 262,144.

52. AMG053 AMG

(Refer to the figure 66.) Solve the equation.
A) 35,998.
B) 36,072.
C) 62,208.

53. AMG053 AMG

What is the speed ratio of an input gear with 36 teeth meshed to a gear with 20 teeth?
A) 9:5.
B) 1:0.56.
C) 1:1.8.

54. AMG077 AMG

An aircraft was not approved for return to service after an annual inspection and the owner wanted to
fly the aircraft to another maintenance base. Which statement is correct?
A) The owner must obtain a special flight permit.
B) The aircraft may be flown without restriction up to 10 hours to reach another maintenance base.
C) The aircraft becomes a restricted category type until it is approved for return to service.

55. AMG099 AMG

Which of the following is Newtons First Law of Motion, generally termed the Law of Inertia?
A) To every action there is an equal and opposite reaction, if a force is applied to an object, the object
will supply a resistive force exactly equal to and in the opposite direction of the force applied.
B) Force is proportional to the product of mass and acceleration, when a force acts upon a body, the
momentum of that body is changed.
C) Objects at rest tend to remain at rest and objects in motion tend to remain in motion at the same
speed and in the same direction, unless acted on by an external force.

56. AMG025 AMG

When an airworthy (at the time of sale) aircraft is sold, the Airworthiness Certificate
A) becomes invalid until the aircraft is reinspected and approved for return to service.
B) is voided and a new certificate is issued upon application by the new owner.
C) is transferred with the aircraft.

57. AMG063 AMG

A person installing a product, part, or appliance on a type certificated product must make certain that
the item`s records document what type of statement?
A) The product, part, or material meets FAA airworthiness standards.
B) A product produced by an owner or operator does not need a statement.
C) The product or material was not produced under an FAA production approval.

58. AMG107 AMG

When we think of aviation safety in a contemporary way, human error is
A) the starting point.
B) the ending point.
C) the intervention point.

59. AMG116 AMG

The positive aspects of human factor issues is referred to as?
A) Magnificent Seven.
B) Dirty Dozen.
C) MEDA.

60. AMG032 AMG

All of the following are consequences of human error, except
A) mental stressor.
B) catastrophic.
C) personal injury.

61. AMG107 AMG

According to Dr. James Reasons there are two types of human failure which can occur, they are
A) active and latent.
B) mental and physical.
C) proper and improper.

62. AMG107 AMG

The three types of human error are
A) omission, commission, and extraneous.
B) active, latent, and stressor.
C) mental, situational, and physiological.

63. AMG107 AMG

The "SHEL" model is another human factors tool, the goal is to determine not only what the problem is,
but also
A) where and why it exists.
B) how we prevent the problem.
C) how many factors contribute to the error.