For More visit : www.LearnEngineering.

in
EC8352-SIGNALS AND SYSTEMS
TWO MARK QUESTION AND ANSWERS

UNIT I CLASSIFICATION OF SIGNALS AND SYSTEMS

1. Define Signal.

A signal is a function of one or more independent variables which contain

some information.
Eg: Radio signal, TV signal, Telephone signal etc.

2. Define System.

A system is a set of elements or functional block that are connected together

n
and produces an output in response to an input signal.
Eg: An audio amplifier, attenuator, TV set etc.

g.i
3. Define CT signals.

rin
Continuous time signals are defined for all values of time. It is also called as an
analog signal and is represented by x(t).
Eg: AC waveform, ECG etc. ee
4. Define DT signal.
gin
Discrete time signals are defined at discrete instances of time. It
is represented by x(n).
Eg: Amount deposited in a bank per month.
En

5. Give few examples for CT signals.

AC waveform, ECG, Temperature recorded over an interval of time etc.

arn

6. Give few examples of DT signals.

Amount deposited in a bank per month,

Le

7. Define unit step, ramp and delta functions for CT.

w.

Unit step function is defined

as U(t)= 1 for t >= 0
0 otherwise
ww

Unit ramp function is defined as

r(t)= t for t>=0
0 for t<0

Unit delta function is defined

as δ(t)= 1 for t=0
0 otherwise

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

8. State the relation between step, ramp and delta functions (CT).

The relation ship between unit step and unit delta function is
δ(t)= u(t)
The relationship between delta and unit ramp function is
δ(t).dt = r(t)

9. State the classification of CT signals.

The CT signals are classified as follows

(i) Periodic and non periodic signals
(ii) Even and odd signals
(iii) Energy and power signals

n
(iv) Deterministic and random signals.

g.i
10. Define deterministic and random signals.

A deterministic signal is one which can be completely represented by

rin
Mathematical equation at any time.In a deterministic signal there is
no uncertainty with respect to its value at any time.
Eg: x(t)=cosωt ee
x(n)=2πfn
A random signal is one which cannot be represented by any mathematical
equation.
gin
Eg: Noise generated in electronic components, transmission
channels, cables etc.

11. Define power and energy signals.

En

The signal x(t) is said to be power signal, if and only if the normalized
average power p is finite and non-zero.
arn

Ie. 0<p<4
A signal x(t) is said to be energy signal if and only if the
total normalized energy is finite and non-zero.
Ie. 0<E< 4
Le

12. Compare power and energy signals.

w.

Sl.No POWER SIGNAL ENERGY SIGNALS

1. The normalized average Total normalized energy is

ww

power is finite and non-zero finite and non- zero.

2. Practical periodic signals Non-periodic signals are

are power signals energy signals

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

13. Define odd and even signal.

A DT signal x(n) is said to be an even signal if x(-n)=x(n) and an

odd signal if x(-n)=-x(n).
A CT signal is x(t) is said to be an even signal if x(t)=x(-t) and an odd
signal if x(-t)=-x(t).

14. Define periodic and aperiodic signals.

A signal is said to be periodic signal if it repeats at equal intervals.

Aperiodic signals do not repeat at regular intervals.
A CT signal which satisfies the equation x(t)=x(t+T0) is said to be periodic and a
DT signal which satisfies the equation x(n)=x(n+N)is said to be periodic.

n
15. State the classification or characteristics of CT and DT systems.

g.i
The DT and CT systems are according to their characteristics as follows
(i). Linear and Non-Linear systems

rin
(ii). Time invariant and Time varying systems.
(iii). Causal and Non causal systems.
(iv). Stable and unstable systems. ee
(v). Static and dynamic systems.
(vi). Inverse systems.
gin
16. Define linear and non-linear systems.

A system is said to be linear if superposition theorem applies to that

system. If it does not satisfy the superposition theorem, then it is said to be a
En

nonlinear
system.
arn

17. Define Causal and non-Causal systems.

A system is said to be a causal if its output at anytime

depends upon present and past inputs only.
Le

A system is said to be non-causal system if its output depends upon future

inputs also.
w.

18. Define time invariant and time varying systems.

A system is time invariant if the time shift in the input signal results
in corresponding time shift in the output.
ww

A system which does not satisfy the above condition is

time variant system.

19. Define stable and unstable systems.

When the system produces bounded output for bounded input,
then the system is called bounded input, bounded output stable.
A system which doesnot satisfy the above condition is called
a unstable system.

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

20. Define Static and Dynamic system.

A system is said to be static or memoryless if its output depends upon
the present input only.
The system is said to be dynamic with memory if its output depends upon
the present and past input values.

UNIT II
ANALYSIS OF CT SIGNALS

1. Define CT signal

Continuous time signals are defined for all values of time. It is also
called as an analog signal and is represented by x(t).

n
Eg: AC waveform, ECG etc.

g.i
2. Compare double sided and single sided spectrums.

The method of representing spectrums of positive as well

rin
as negative frequencies are called double sided spectrums.
The method of representing spectrums only in the positive frequencies
is known as single sided spectrums. ee
3. Define Quadrature Fourier Series.
gin
Consider x(t) be a periodic signal. The fourier series can be written for
this signal as follows
x(t)= a0 + an cosω0nt + bnsinω0nt
En

n 1 n 1
This is known as Quadrature Fourier Series.

4.Define polar Fourier Series.

arn

x(t)= D0 + Dncos((2πnt / T0) +

n 1

The above form of representing a signal is known as Polar Fourier series.

Le

5.Define exponential fourier series.

w.

j2πnt / T0
x(t)= Cn e
n 1

The method of representing a signal by the above form is known

ww

as exponential fourier series.

6. State Dirichlets conditions.

(i).The function x(t) should be single valued within the interval T0

(ii). The function x(t) should have atmost a finite number of discontinuities
in the interval T0
(iii). The function x(t) should have finite number of maxima and
minima in the interval T0
(iv). The function should have absolutely integrable.

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

7. State Parsevals power theorem.

Parsevals power theorem states that the total average power of a periodic
signal x(t) is equal to the sum of the average powers of its phasor components.

8.Define Fourier Transform.

Let x(t) be the signal which is the function of time t.

The fourierr transform of x(t) is given by
-jωt
X(ω)= x(t)e .dt

n
9. State the conditions for the existence of fourier series.

g.i
(i). The function x(t) should be single valued in any finite time interval T
(ii). The function x(t) should have atmost finite number of
discontinuities in any finite time interval T.

rin
(iii). The function x(t) should have finite number of maxima and
minima in any time interval T.
(iv) The function x(t) should be absolutely integrable.
10. Find the Fourier transform of function
x(t)=δ(t) Ans: 1
ee
11. State Rayleigh’s energy theorem.
gin
Rayleigh‟s energy theorem states that the energy of the signal may
be written in frequency domain as superposition of energies due to
individual spectral frequencies of the signal.
En

12.Define laplace transform.

Laplace transform is the another mathematical tool used for analysis of

continuous time signals and systems.It is defined as
arn

-st
F(s) = f(t) e dt

13. Obtain the laplace transform of ramp function.

Le

2
Ans: 1/s
w.

14. What are the methods for evaluating inverse Laplace

transform. The two methods for evaluating inverse laplace transform are
ww

(i). By Partial fraction expansion

method. (ii). By convolution integral.

15. State initial value theorem.

If x(t)----- L--------- _X(s), then value of x(t)is geven as,

lim
x(0+) =t 0 [sX(s)]
provided thet the first derivative of x(t) should be laplace transformable.

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

16. State final value theorem.

If x(t) and X(s) are laplace transform pairs, then the final value of x(t)
is given as ,
Lim t->4x(t)= Lim s->0[sX(s)]

17. State the convolution property of fourier transform.

If x1(t) and x1(f) are fourier transform pairs and x2(t) and x2(f) are
fourier transform pairs, then
x1(t)x2(f-t)dt is fourier transform pair with X1(f)X2(f)

n
18.What is the relationship between Fourier transform and Laplace
transform.

g.i
X(s)=X(jw) when s=jw
This states that laplace transform is same as fourier transform when s=jw.

rin
19.Find the fourier transform of sgn function.

Ans: 2/jW ee
20. Find out the laplace transform of
at
gin
f(t)=e Ans: 1/(s-a)

UNIT III
En

LTI- CT SYSTEMS

1. Define LTI-CT systems.

arn

In a continuous time system if the time shift in the input signal results in
the corresponding time shift in the output, then it is called the LTI-CT system
Le

2. What are the tools used for analysis of LTI-CT systems?

The tools used for the analysis of the LTI-CT system are
Fourier transform
w.

Laplace transform

3.Define convolution integral.

ww

The convolution of of two signals is given by

y(t)= x(t)*h(t)
where
x(t)*h(t)= x(t)h(t-τ).dt
This is known as convolution integral.

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

4.List the properties of convolution integral.

a. commutative property
b. distributive property
c. associative property
d. shift property
e. convolution with an impulse
f. width property

5.State commutative property of convolution.

The commutative property of convolution

states that x1(t)*x2(t)=x2(t)*x1(t)

n
6.State the associative property of convolution.

g.i
Associative property of convolution states
that x1(t)*[x2(t)*x3(t)]=[x1(t)*x2(t)]*x3

rin
7.State distributive property of convolution.

The distributive property states that ee

x1(t)*[x2(t)+x3(t)]=x1(t)*x2(t)+x1(t)*x3(t)

8. When the LTI-CT system is said to be dynamic?

gin

In LTI CT system, the system is said to be dynamic if the present output

depends only on the present input.
En

9. When the LTI-CT system is said to be causal?

An LTI continuous time system is causal if and only if its

arn

impulse response is zero for negative values of t.

10. When the LTI-CT system is said to be stable?

Le

A LTI-CT system is said to be stable if the impulse response of the system

is absolutely integrable.
w.

11. Define natural response.

Natural response is the response of the system with zero input. It

ww

depends on the initial state of the system. It is denoted by yn(t)

12. Define forced response.

Forced response is the response of the system due to input alone when the
initial state of the system is zero. It is denoted by yf(t).

13. Define complete response.

The complete response of a LTI-CT system is obtained by adding the

natural response and forced respons

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

y(t)= yn(t)+ yf(t)

14.Mention the advantages of direct form II structure over direct form I
structure.
No.of integrators are reduced to half
15. Define Eigen function and Eigen
value. In the equation given below,
y(t)=H(s)est
H(s) is called Eigen value and est is called Eigen function.
18. Define Causality and stability using poles.
For a system to be stable and causal, all the poles must be located in
the left half of the s plane
19. Find the impulse response of the system y(t)=x(t-t0) using laplace
transform.
Ans:

n
h(s)= d(t-t0)
20. The impulse response of the LTI CT system is given as h(t)=e-t u(t).

g.i
Determine
transfer function and check whether the system is causal
and stable. Ans:

rin
H(s)=1/(s+1)
The system is causal,stable.
UNIT-4ee
ANALYSIS OF DISCRETE TIME SIGNALS
gin
1. Define DTFT.
Let us consider the discrete time signal x(n).Its DTFT is denoted as X(w).It is
given as X(w)= x(n)e-jwn
En

2. State the condition for existence

of DTFT? The conditions are
• If x(n)is absolutely summable
arn

then |x(n)|<
• If x(n) is not absolutely summable then it should have finite energy
for DTFT to exit.
Le
w.
ww

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

3. List the properties of

DTFT. _ Periodicity
_ Linearity
_ Time shift
_ Frequency shift
_ Scaling
_ Differentiation in frequency domain
_ Time reversal
_ Convolution
_ Multiplication in time domain
_ Parseval‟s theorem

4. What is the DTFT of unit sample?

The DTFT of unit sample is 1 for all values of w.

n
g.i
5. Define DFT.
DFT is defined as X(w)= x(n)e-jwn. Here
x(n) is the discrete time sequence X(w)

rin
is the fourier transform ofx(n).

6. Define Twiddle factor.

The Twiddle factor is defined as WN=e-j2 /N ee
7. Define Zero padding.
The method of appending zero in the given sequence is called as Zero padding.
gin

8. Define circularly even sequence.

A Sequence is said to be circularly even if it is symmetric about the point zero
En

on the circle.
x(N-n)=x(n),1<=n<=N-1.

9. Define circularly odd sequence.

arn

A Sequence is said to be circularly odd if it is anti symmetric about point x(0)

on the circle

10. Define circularly folded sequences.

Le

A circularly folded sequence is represented as x((-n))N. It is obtained by

plotting x(n) in clockwise direction along the circle.
w.

11. State circular convolution.

This property states that multiplication of two DFT is equal to
circular convolution of their sequence in time domain.
ww

12. State parseval‟s theorem.

Consider the complex valued sequences x(n)
and y(n).If x(n) ----_X(k)
y(n) ----_Y(k)
then x(n)y*(n)=1/N X(k)Y*(k)

13. Define Z transform.

The Z transform of a discrete time signal x(n) is denoted by X(z) and
is given by X(z)= x(n)Z-n.

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

14. Define ROC.

The value of Z for which the Z transform converged is called region
of convergence.

15. Find Z transform of

x(n)={1,2,3,4} x(n)= {1,2,3,4}
X(z)= x(n)z-n
= 1+2z-1+3z-2+4z-3.
= 1+2/z+3/z2+4/z3.

16. State the convolution property of Z transform.

The convolution property states that the convolution of two sequences in
time domain is equivalent to multiplication of their Z transforms.

n
g.i
17. What z transform of (n-m)?
By time shifting property Z[A
(n-m)]=AZ-m sinZ[ (n)] =1

rin
18. State initial value theorem.
If x(n) is causal sequence then its initial value is
given by x(0)=lim X(z) ee
19. List the methods of obtaining inverse Z transform.
Inverse z transform can be obtained by using
gin
_ Partial fraction expansion.
_ Contour integration
_ Power series expansion
_ Convolution.
En

20. Obtain the inverse z transform of X(z)=1/z-a,|z|>|a|

Given X(z)=z-1/1-az-1
arn

By time shifting property

X(n)=an.u(n-1)
UNIT-5
Le

LINEAR TIME INVARIANT DISCRETE TIME SYSTEMS

1. Define convolution sum?

w.

If x(n) and h(n) are discrete variable functions, then its convolution
sum y(n) is given by,
y(n)=_ x(k) h(n-k)
ww

2. List the steps involved in finding convolution sum?

o folding
o Shifting
o Multiplication
o Summation

3.List the properties of convolution?

o Commutative property of convolution
x(n) * h(n) = h(n) * x(n) = y(n)
o Associative property of convolution

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

[ x(n) * h1(n)] * h2(n) = x(n) * [h1(n) *

h2(n)] o Distributive property of convolution
x(n) * [h1(n) + h2(n)] = x(n) * h1(n) + x(n) * h2(n)

4. Define LTI causal system?

A LTI system is causal if and only if ,h(n) = 0 for n<0.This is the
sufficient and necessary condition for causality of the system.

5. Define LTI stable system?

The bounded input x(n) produces bounded output y(n) in the LTI system only if,
_ | h(k)| <_. When this condition is satisfied ,the system will be stable.

6. Define FIR system?

n
The systems for which unit step response h(n) has finite number of terms, they
are called Finite Impulse Response (FIR) systems.

g.i
7. Define IIR system?
The systems for which unit step response h(n) has infinite number of

rin
terms, they are called Infinite Impulse Response (IIR) sysrems.

8. Define non recursive and recursive systems?ee

When the output y(n) of the system depends upon present and past
inputs then it is called non-recursive system.
When the output y(n) of the system depends upon present and past inputs as
gin
9. State the relation between fourier transform and z transform?
The fourier transform is basically the z-transform of the sequence evaluated
on unit circle.
En

i.e., X(z)|z=e
jw = X(w) at |z|=1 i.e., unit circle.
arn

10. Define system function?

H(z)= Y(z) is called system function.It is the z transform of the unit
sample
X(Z)
Le

response h(n) of the system.

11. What is the advantage of direct form 2 over direct form 1 structure?
w.

The direct form 2 structure has reduced memory requirement compared to

direct form 1 structure.
ww

12. Define butterfly computation?

In the figure the two values „a‟ and „b‟ are available as input. From these
two values
„A‟ and „B‟ are computed at the output. This operation is
called Butterfly computation.

13.What is an advantage of FFT over DFT?

FFT algorithm reduces number of
computations. 14. List the applications of FFT?
o Filtering
o Spectrum analysis

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

o Calculation of energy spectral density

15. How unit sample response of discrete time system is defined?

The unit step response of the discrete time system is output of the system
to unit
sample sequence. i.e., T[ð(n)]=h(n). Also h(n)=z {H(z)}.

16.A causal DT system is BIBO stable only if its transfer function has
_________.
Ans:A causal DT system is stable if poles of its transfer function
lie within the
unit circle.

n
g.i
17. If u(n) is the impulse response response of the system, What is its step
response?
Here h(n) = u(n) and the input is x(n) =
u(n). Hence the output y(n) = h(n) * x(n)

rin
= u(n) * u(n)

18.Convolve the two sequences x(n)={1,2,3} and h(n)={5,4,6,2}

ee
Ans: y(n)={5,14,29,26,22,6}

19.State the maximum memory requirement of N point DFT including twiddle

gin
factors?
Ans: [2N+N/2]

20.Determine the range of values of the parameter „a‟ for which the linear
En

time invariant
system with impulse response h(n)=an u(n) is stable?
Ans: H(z)= z , There is one pole at z=a. The system is stable, if
arn

all its poles.

z-a
i.e., within the unit circle. Hence |a| < 1 for stability.
Le
w.
ww

For More visit : www.LearnEngineering.in

For More visit : www.LearnEngineering.in

n
g.i
rin
ee
gin
En
arn
Le
w.
ww

For More visit : www.LearnEngineering.in