TRAILER AXLE BEAMS

TRAILER AXLE BEAMS NOTES:

1) "SF" in part # denotes straight axle
In order to replace a sprung axle *
beam properly, the following 2) "DF" in part # denotes drop axle
information is needed; (4" drop center of beam to center of
• bearing numbers or a specific hub spindle)
number (often on the face of the drum
or back of hub) which tells us if your
3) "TF" in part # denotes a TORFLEX axle
hubs will fit our axle and an
which has a steel torsion bar surrounded
approximate capacity
by 4 natural rubber cords encased in the
• length of axle, whether it be track main structural member of the axle
(center of tire to center of tire), hub face, beam, acting as its means of suspension
or even an overall tip-to-tip dimension (no leaf springs need to be used). The
allows us to figure what's being replaced beam attaches directly to the trailer
• straight or drop axle ? frame using brackets and the "Spring
• size of tubular or square axle being Center" column gives the "outside of
replaced which determines if new brackets" dimension, which must match
U-bolts are needed up to the trailer frame.
Starting Angle refers to the position of
the spindle in reference to the trailer
In order to replace a torsional axle * frame without a load and is important for
beam properly, the following clearance purposes (tires & wheels,
information is needed: loaded vs. unloaded, etc). TORFLEX
axles are square, not tubular.
• The best, most efficient reference is the
serial number found on the original axle.
• bearing numbers or a specific hub 4) SQG in part# denotes 2” square
number (often on the face of the drum galvanized construction. These type
or back of hub) which tells us if your axles are supplied with EZ-lube fitttings.
hubs will fit our axle and an
approximate capacity 5) Axles come complete with brake
• length of axle, whether it be track flanges, loose spring seats, axle nuts,
(center of tire to center of tire), hub face, & cotter pins.
brake flange to brake flange, or even an
overall tip-to-tip dimension allows us to 6) * denotes EZ-lube option is available in
figure what's being replaced stock by adding "EZ" to end of number.
• an "outside of bracket to outside of
bracket" dimension on the torsion axle
being replaced or outside of frame to
outside of frame dimension of the trailer
being outfitted (should be same length)
• how do the axle mounting brackets allow
the axle to be mounted to the frame ?
• what is the "starting angle" of the axle
torsion arms (position of spindles) rela-
tive to the trailer frame, and is that angle
up or down ?

* CALL US FOR ASSISTANCE AT R.H. SCALES COMPANY

WE CAN FAX YOU A SIMPLE-TO-USE AXLE WORK SHEET ORDER FORM
1
 TRAILER AXLE BEAMS

2,000 LB. TUBULAR AXLE BEAMS 3,500 LB. TUBULAR AXLE BEAMS
(1 3/4" TUBE WITH 1" STRAIGHT SPINDLES) (2 3/8" TUBE WITH 1 3/8" X 1 1/16" STEP SPINDLES)
PART # TRACK HUB FACE TIP-TO-TIP SPRING PART # TRACK HUB TIP-TO-TIP SPRING
CENTER FACE CENTER
2S-49 49" 49" 53.5" 31-36 " 3SF-43.5 43.5" 44.5" 49" 39-45 "
2S-51 51" 51" 55.5" 33-38 " 3SF-62 62" 63" 67 3/4" 45-50"
2S-54 55" 55" 59.5" 37-42" 3SF-69 69" 70" 73 3/4" 52-57"
2S-58 58" 58" 62.5" 40-45" 3SF-73 73" 74" 78 1/2" 56-61"
2S-60 61" 61" 65.5" 43-48 " 3SF-75.5 -3* 75.5" 76.5" 81" 71-77"
2S-62 63" 63" 67.5" 45-50" 3SF-76.5 76 1/2" 77 1/2" 82" 72-76"
2S-64 65" 65" 69.5" 47-52" 3SF-79 79" 80" 84 1/2" 74 1/2 - 80 1/2"
2S-70 71” 71” 75.5" 53-58 ” 3SF-84 84" 85" 89 1/2" 67-72"
2S-73 74" 74" 78.5" 56-61 " 3SF-86 86" 87" 91 1/2" 69-74"
2S-77 78" 78" 82.5" 60-65" 3SF-86.5 -3* 86.5" 87.5" 91 1/2" 69-74"
2S-84 85" 85" 88.5" 67-72" 3SF-88 88" 89" 92 1/2" 71-76"
2S-88 89" 89" 93.5" 71-76" 3SF-88 -3* 88" 89" 93 1/2" 71-76"
3SF-91.5 91.5" 92.5" 97" 87-93"
3SF-92 92" 93" 97 1/2" 87 1/2 - 93 1/2"
3SF-94 94" 95" 99 1/2" 77-82"
3SF-94 -3* 94" 95" 99 1/2" 77-82"
3SF-96 96" 97" 101 1/2" 79-84"
3SF-96 -3* 96" 97" 101 1/2" 79-84"
3DF-62 62" 63" 67 1/2" 45-50"
3DF-73 73" 74" 78 1/2" 56-61"
3DF-84 84" 85" 89 1/2" 67-72"
3DF-86 86" 87" 91 1/2" 69-74"
3DF-88 88" 89" 93 1/2" 71-76"
3DF-89 89" 90" 94 1/2 " 72-77"
3DF-93 93" 94" 98" 76-81"
3DF-96 96" 97" 101" 79-84"
*NOTE: Constructed with Larger 3” Diameter Tube

GALVANIZED AXLE BEAMS

BEAMS
2,000 LB. 2" SQUARE BEAMS
PART # TRACK TUBE TIP-TO-TIP SPRING
CENTER
2S-49SQG A
49" 43" 54" Variable
6,000 LB. TUBULAR AXLE BEAMS 2S-53SQG A
53" 46" 58" Variable
( 3" TUBULAR WITH 1 3/4" X 1 1/4" STEP SPINDLES) 2S-57SQG A
57.13" 51" 62" Variable
PART # TRACK HUB TIP-TO-TIP SPRING 2S-59SQG A
59" 53" 64" Variable
2S-65SQG A
65" 59" 70" Variable
FACE CENTER 2S-68SQG A
68" 63" 74" Variable
6SF-42 42" 43" 49" 24-28" 2S-75SQG A
75" 69" 80" Variable
6SF-59 59" 60" 66" 41-45" 2S-87SQG A
87" 81" 92" Variable
6SF-62 62" 63" 68 1/2" 44-48" 2S-89SQG A
89" 83" 94" Variable
6SF-73 73" 74" 80" 55-59" 2S-91SQG A
91" 85" 96" Variable
6SF-74.75 74 3/4" 75 3/4" 81 1/2" 56 3/4 - 60 3/4" A
No flanges on above axles, 1-1/16” spindles with EZ-Lube Grease Fitting,
6SF-79.5 79 1/2" 80 1/2" 84 1/2" 61 1/2 - 65 1/2" uses 8-91-90M, 8-259-91M or 8-259-91GM Marine Use Hub Assembly
6SF-81.25 81 1/4" 82 1/4" 88 1/4" 63 1/4 - 67 1/4"
6SF-84 84" 85" 90 1/2" 66-71"
6SF-86 86" 87" 92 1/2" 68-72" 3,500 LB. 2" SQUARE BEAMS
6SF-88 88" 89" 94 1/2" 70-74"
6SF-MHU-88 88" 88" 93" 70-74" PART # TRACK TUBE TIP-TO-TIP SPRING
6SF-91 91" 92" 97 1/2" 72-76" CENTER
6SF-94 94" 95" 101 1/2" 76-80" 3SF-73SQG B
73" 65.25" 78" Variable c

6SF-96 96" 97" 102" 78-82" 3SF-75SQG B

75" 67.25" 80" Variable c

6SF-100 100" 101" 105-3/4" 88-93" 3SF-77SQG B

77" 69.25" 82" Variable c

6DF-73 73" 74" 80" 55-59" 3SF-85SQG B

85" 77.25" 90" Variable c

6DF-74.5 74.5" 75.5" 82" 64-69 " 3SF-87SQG B

88" 79.25" 92" Variable c

6DF-84 84" 85" 91" 66-71" 3SF-91SQG B

91" 83.25" 96" Variable c

6DF-86 86" 87" 92.75" 68-72" B

Above axles have flanges ,1-3/8 x 1-1/16” step spindles
6DF-88 88" 89" 95" 70-74"
with EZ-Lube Grease Fitting, can use HD Hubs or Disc
6DF-94 94" 95" 102" 76-80" C
Spring Center No More Than 15" from Track
6DF-96 96" 97" 103" 78-82"

2
 MULTI-ADJUSTABLE TORSION AXLES • HUB ASSEMBLIES

3750# Powder Coated Splined Torsion Axle Beams

A = Axle Beam

B = End Unit
B = End Unit

C = Bracket C = Bracket

Perfect for your Torsion Axle replacement or Upgrade to Torsion Axles.

You can easily do this with a Tie Down Engineering Torsion Axle Splined Beam.
Just use the proper add-on Adjustable Mounting Brackets (C) and the add-on Adjustable Splined Torsion Spindle Arm Units (B).
This gives you the ability to change Torsion Arm angles and frame centers. Pick an Axle (A) from one of our popular Hub Face
Measurements and you can adjust the torsion arm angle and the frame spacing to your specifications.

A Powder Coated Axles 3750# Capacity B # 86886 Splined

2-1/2” Square Tubes - Straight Beam or V-Beam Torsion Arm End Units
Part# Hub Face Brake Flange Beam Outside Bracket Right & Left Pair Torsion Arms can be
Length Length Length Min Max adjusted from 45º down to 25º up.
Spindle Size: 1-3/8" x 1-1/16"
86870 83.00” 76.66” 74.93” 59.00” 67.00” (Standard w/Super-Lube Zerk)
86871 85.00” 78.66” 76.93” 61.00” 69.00”
Each end unit comes with spindle nut and
86872 87.00” 80.66” 78.93” 63.00” 71.00” washer and Torsion Arm install bolt and
86873 89.00” 82.66” 80.93” 65.00” 73.00” nut. Includes pre-attached brake mounting
86874 91.00” 84.66” 82.93” 67.00” 75.00” flanges (4-hole).
86875 93.00” 86.66” 84.93” 69.00” 77.00”
86876 95.00” 88.66” 86.93” 71.00” 79.00”
C # 86884 Bracket (Pair)
86877 (V-Beam) 85.00” 78.66” 76.93” 61.00” 69.00” Utility Mount Weld-On
86878 (V-Beam) 87.00” 80.66” 78.93” 63.00” 71.00” Weld-On Frame
86879 (V-Beam) 89.00” 82.66” 80.93” 65.00” 73.00” Mount for Utility
Style Bracket

C # 86883 Bracket (Pair) C # 86885 Bracket (Pair) C # 86889 Bracket (Pair)

Utility Mount 1-1/4" Rise Marine Style Mount Utility Style Low Pro
Allows you to adjust the Allows you to adjust
frame centers on the axle the frame centers on
Low Profile
you choose. the axle you choose.
Utility Style Brackets
One pair includes One pair includes all
all hardware. hardware.

Complete Popular Hub Assemblies in

Attractive Viz-Packs for Retail / Display
INCLUDES BEARINGS, CAP, SEAL, & LUG NUTS
(OR WHEEL BOLTS WHERE APPLICABLE)

PART# SPINDLE SIZE BOLT BEARING #'S MAX.

PATTERN CAPACITY/PR.
81060 1" straight 4H - 4 " L44643 in/out 2000 lbs.
81065 1 1/16" straight 4H - 4 " L44649 in/out 2000 lbs.
86758 1" straight 5H - 4 1/2" L44643 in/out 2000 lbs.
86759 (Galvanized) 1" straight 5H - 4 1/2" L44643 in/out 2000 lbs.
86760 1 1/16" straight 5H - 4 1/2" L44649 in/out 2200 lbs.
86761 (Galvanized) 1 1/16" straight 5H - 4 1/2" L44649 in/out 2200 lbs.
86762 1 3/8" x 1 1/16" 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
86763 (Galvanized) 1 3/8" x 1 1/16" 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
3
 HIGH SPEED HUB ASSEMBLIES

2000LB. CAPACITY PER PAIR FOR 1” STRAIGHT SPINDLES

PART # SPINDLE SIZE BOLT BEARING #'S MAX.
PATTERN CAPACITY/PR.
8-91-80 1" straight 4H - 4" L44643 in/out 2000 lbs.
8-91-80M 1" straight 4H - 4" L44643 in/out 2000 lbs.
BB / EZ (See Below)
For Marine Applications -Supplied less cap, plus HD seal
8-259-81 1" straight 5H - 4 1/2" L44643 in/out 2000 lbs.
8-259-81M 1" straight 5H - 4 1/2" L44643 in/out 2000 lbs.
BB / EZ (See Below)
For Marine Applications -Supplied less cap, plus HD seal

2200LB. CAPACITY PER PAIR FOR 1-1/16” STRAIGHT SPINDLES

PART # SPINDLE SIZE BOLT BEARING #'S MAX.
PATTERN CAPACITY/PR.
Capacity 2000lb. per pair
8-91-90 1 1/16" straight 4H - 4 L44649 in/out 2200 lbs.
Larger 6.5” Hub
8-91-90B 1 1/16" straight 4H - 4 L44649 in/out 2200 lbs.
Face for 13” wheels
Boxed for Retail / Display
8-91-90M 1 1/16" straight 4H - 4 L44649 in/out 2200 lbs.
For Marine Applications -Supplied less cap, plus HD seal BB / EZ (See Below)
8-258-90 1 1/16" straight 5H - 4 1/2" L44649 in/out 2000 lbs.
8-259-90S 1 1/16” straight 5H - 4 1/2” L44649 in/out 2200 lbs.
8-259-91 1 1/16" straight 5H - 4 1/2" L44649 in/out 2200 lbs.
8-259-91B 1 1/16" straight 5H - 4 1/2" L44649 in/out 2200 lbs.
This hub has a shorter Boxed for Retail / Display
(1-5/8”) back-to-back 8-259-91M 1 1/16" straight 5H - 4 1/2" L44649 in/out 2200 lbs.
race dimension. For Marine Applications -Supplied less cap, plus HD seal BB / EZ (See Below)

3500LB. CAPACITY PER PAIR FOR 1-3/8” X 1-1/16” TAPERED SPINDLES

PART # SPINDLE SIZE BOLT BEARING #'S MAX.
Note: Maximum capacity PATTERN CAPACITY/PR.
3000lb. per pair D17214 1 1/4" x 3/4" 5H - 4 1/2" LM67048 in/LM11949 out 3000 lbs.
For 1-1/4” X 3/4” spindle
8-248-90 1 3/8" x 1 1/16" 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
8-248-90B 1 3/8" x 1 1/16" 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
Boxed for Retail / Display
8-248-90I 1 3/8" x 1 1/16" 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
= 8-248-90 Value Priced Manufacturer
8-248-90B I 1 3/8" x 1 1/16" 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
= 8-248-90 I Value Priced Manufacturer, Boxed for Retail / Display
8-248-90M 1 3/8" x 1 1/16" 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
= 8-248-90 For Marine Use -Supplied less cap, plus HD seal BB / EZ (See Below)
8-248-90M I 1 3/8" x 1 1/16" 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
= 8-248-90M Value Priced, less cap, plus HD seal for Marine Use BB / EZ (See Below)
8-248-92 1 3/8" x 1 1/16" 5H - 4 3/4" L68149 in/L44649 out 3500 lbs.
8-256-91 1 3/8" x 1 1/16" 5H - 5" L68149 in/L44649 out 3500 lbs.
8-256-90 1 3/8" x 1 1/16" 5H - 5 1/2" L68149 in/L44649 out 3500 lbs.
8-251-90 1 3/8" x 1 1/16" 6H - 5 1/2" L68149 in/L44649 out 3500 lbs.

5200LB. CAPACITY PER PAIR FOR 1-3/4” X 1-1/4” TAPERED SPINDLES

PART # SPINDLE SIZE BOLT BEARING #'S MAX.
*Note: Maximum capacity PATTERN CAPACITY/PR.
4000lb. per pair 8-261-90* 1 3/8" x 1 1/4" 5 spoke UTG L68149 in/LM67048 out 4000 lbs. (MH)
For 1-3/8” X 1-1/4” spindle
8-157-90 1 3/4" x 1 1/4" 4H - 9.44" 25580 in/LM67048 out 5200 lbs.
8-213-90 1 3/4" x 1 1/4" 6H - 5 1/2" 25580 in/LM67048 out 5200 lbs.
8-213-90M 1 3/4" x 1 1/4" 6H - 5 1/2" 25580 in/LM67048 out 5200 lbs.

7000LB. CAPACITY PER PAIR FOR 1-3/4” X 1-1/4” TAPERED SPINDLES

PART # SPINDLE SIZE BOLT BEARING #'S MAX.
PATTERN CAPACITY/PR.

8-231-92 1 3/4" x 1 1/4" 8H - 6 1/2" 25580 in/14125A out 7000 lbs.

NOTE: BB/EZ = 1980A Bearing Protector or #21-41 EZ Lube Cap & Plug Recommended -
Please order separately

4
 HIGH SPEED HUBS & DRUMS
HUBS & DRUMS ONE PIECE UNIT INCLUDES BEARINGS, CAP, SEAL, & LUG NUTS
2200LB. CAPACITY PER PAIR FOR 1-1/16” STRAIGHT SPINDLES
PART # BRAKE SIZE BOLT BEARING #'S MAX.
PATTERN CAPACITY/PR.
8-257-90 7" X 1 1/4" elec. 5H - 4 1/2" L44649 in/out 2200 lbs.
8-271-90 7" X 1 3/4" hydr. only 5H - 4 1/2" L44649 in/out 2200 lbs.
3500LB. CAPACITY PER PAIR FOR 1-3/8” X 1-1/16” TAPERED SPINDLES
8-252-90 7" X 1 3/4" hydr. only 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
D15445 8 1/2" x 2 1/4" hydr. 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
8-247-90 10" x 2 1/4" elec/hydr. 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
8-247-90 I 10" x 2 1/4" elec/hydr. 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
=8-247-90 Value Priced Manufacturer
8-247-90 M 10" x 2 1/4" elec/hydr. 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
For Marine Applications = 8-247-90 supplied less cap, plus HD seal BB / EZ (See Below)
8-247-90 MI 10" x 2 1/4" elec/hydr. 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
For Marine Use= 8-247-90I Value Priced, less cap, plus HD seal BB / EZ (See Below)
86754 10" x 2 1/4" elec/hydr. 5H - 4 1/2" L68149 in/L44649 out 3500 lbs.
Pre-Greased Boxed Assembly Complete with Cap, Bearings and Seals
8-249-91 10" x 2 1/4" elec/hydr. 5H - 5" L68149 in/L44649 out 3500 lbs.
8-249-90 10" x 2 1/4" elec/hydr. 5H - 5 1/2" L68149 in/L44649 out 3500 lbs.
Note: 4000lb. Capacity 8-250-90 10" x 2 1/4" elec/hydr. 6H - 5 1/2" L68149 in/L44649 out 3500 lbs.
for Motorhome Axles 8-222-90 12" x 2" elec/hydr. 5 spoke UTG L68149 in/LM67048 out 4000 lbs. (MH)

5200LB. CAPACITY PER PAIR FOR 1-3/4” X 1-1/4” TAPERED SPINDLES

PART # BRAKE SIZE BOLT BEARING #'S MAX.
PATTERN CAPACITY/PR.
8-155-90 12" x 2" elec/hydr. 4H - 9.44" 25580 in/LM67048 out 5200 lbs.
8-201-90 12" x 2" elec/hydr. 6H - 5 1/2" 25580 in/LM67048 out 5200 lbs.
8-201-90 M 12" x 2" elec/hydr. 6H - 5 1/2" 25580 in/LM67048 out 5200 lbs.
For Marine Use= 8-201-90 supplied less cap, plus HD seal BB / EZ2 (See Below)

6000LB. CAPACITY PER PAIR FOR 1-3/4” X 1-1/4” TAPERED SPINDLES

8-201-90 I 12" x 2" elec/hydr. 6H - 5 1/2" 25580 in/15123 out 6000 lbs.
= 8-201-90 Value Priced, Heavier 6K Capacity
8-201-90 MI 12" x 2" elec/hydr. 6H - 5 1/2" 25580 in/15123 out 6000 lbs.
For Marine Use= 8-201-90 I Value Priced, less cap, plus HD seal BB / EZ2 (See Below)
86753 12" x 2" elec/hydr. 6H - 5 1/2" 25580 in/15123 out 6000 lbs.
Pre-Greased Boxed Assembly Complete with Cap, Bearings and Seals
8-174-90 12" x 2" elec/hydr. 5 spoke UTG 25580 in/15123 out 6000 lbs.

7K - 8K CAPACITY PER PAIR FOR 1-3/4” X 1-1/4” TAPERED SPINDLES

PART # BRAKE SIZE BOLT BEARING #'S MAX.
PATTERN CAPACITY/PR.
8-219-90 12" x 2" elec/hydr. 8H - 6 1/2" 25580 in/ 14125A out 7000 lbs.
Note: This Drum Uses 1/2” Studs & Nuts (for 9/16” See 8-219-91)
8-219-90 I 12" x 2" elec/hydr. 8H - 6 1/2" 25580 in/ 14125A out 7000 lbs.
= 8-219-90 Value Priced Manufacturer - Uses 1/2” Studs & Nuts
8-219-91 12" x 2" elec/hydr. 8H - 6 1/2" 25580 in/ 14125A out 7000 lbs.
Note: This Drum Uses 9/16” Studs & Nuts (for 1/2” See 8-219-90 or 8-219-90I)
8-218-90 12 1/4" x 3 3/8" elec/hydr. 8H - 6 1/2" 25580 in/ 02475 out 8000 lbs.
Hub & drum with 4.56 hub pilot (old style), 8-285 has 4.75 pilot (new style), both w/5/8" studs
8-285-92 12 1/4" x 3 3/8" elec/hydr. 8H - 6 1/2" 25580 in/ 02475 out 8000 lbs.
Hub & drum with 4.75 hub pilot (new style), 8-218 has 4.56 pilot (old style), both w/5/8" studs
BB / EZ
1980A Bearing Protector or 21-41 EZ Lube Cap & Plug Recommended - Please order separately
BB2 / EZ2
2441 Bearing Protector or 21-42 EZ Lube Cap & Plug Recommended - Please order separately

2 PIECE HUBS & DRUMS ( BEARINGS, CAPS, SEALS, & LUG NUTS )
DRUMS IN STOCK, HUBS SUPPLIED SPECIAL ORDER

DRUM# HUB# ASSEMBLY# SIZE BOLT PATTERN IN/OUT BEARING CAPACITY

9-44-1 8-288-3 8-288-90 12 1/4" x 3 3/8" 8H - 6 1/2" 387A in/25580 out 9 & 10k GD
9-27-1 8-214-5 N/A 12 1/4" x 4" 8H - 6 1/2" 395S in/387A out 10k HD
9-27-3 (ABS) 8-214-5 N/A 12 1/4" x 4" 8H - 6 1/2" 395S in/387A out 10k HD
9-28-1 8-216-8 N/A 12 1/4" x 5" 8H - 6 1/2" 3984 in/28682 out 12k
9-28-5 (ABS) 8-216-8 N/A 12 1/4" x 5" 8H - 275mm 3984 in/28682 out 15k
9-40-1 VARIES N/A 12 1/4" x 7 1/2" 10H - 8 3/4" HM218248 in/HM212049 out 20k

5
 MOBILE HOME 2-PIECE HUBS • NEV-R-LUBE • BEARINGS

MOBILE HOME
HUB / DRUM
Standard Grease Lube Parts
ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION
1 10-41 Nylon Grease Seal 6 5-27 Spindle Washer
2 31-33-2 Inner Bearing Cone, L68149 7 6-1 Spindle Nut
3 31-33-1 Inner Bearing Cup, L68111 8 19-2 Cotter Pin
4 31-32-1 Outer Bearing Cup, LM67010 9 21-1 Grease Cap
5 31-32-2 Outer Bearing Cone, LM67048 10 15-2 Rim Clamp
Mobile Home Brakes
11 7-36 1/2 -13 Wheel Bolt
are available
Idler Hub/Hub & Drum
See page 22
ITEM PART NO. DESCRIPTION BOLT
24 8-261-4 Idler w/cups Demountable
24 8 222-4 Hub & Drum w/cups Demountable

NEV-R-LUBE HUB & DRUMS

INCLUDES BEARING CARTRIDGE AND BEARING RETAINER
PART # BRAKE SIZE BOLT STUD BEARINGS MAX.
PATTERN SIZE CAPACITY/PAIR
8-388-80 12” x 2” 6H - 5 1/2" 1/2" 42mm 5200lb.
8-389-82 12” x 2” 8H - 6 1/2" 1/2" 50mm 7000lb.
8-385-80 12” x 2” 8H - 6 1/2" 5/8" 50mm 7000lb.
8-385-81 12” x 2” 8H - 6 1/2" 9/16" 50mm 7000lb.
8-385-91 12” x 2” 8H - 6 1/2" 9/16" 50mm 7000lb.
8-389-80 12-1/4” x 3-3/8” 8H - 6 1/2" 5/8" 50mm 8000lb.
8-389-81 12-1/4” x 3-3/8” 8H - 6 1/2" 9/16" 50mm 8000lb.
NEV-R-LUBE
COMPONENTS APPLICATION DESCRIPTION
31-72-3 35mm 3.5k Nev-R-Lube Sealed Cartridge Bearing Pack
31-73-3 42mm 5.2k Nev-R-Lube Sealed Cartridge Bearing Pack
31-71-3 50mm 6k -8k Nev-R-Lube Sealed Cartridge Bearing Pack
5-147-1 42mm Spindle Washer
NEV-R-LUBE
5-149 50mm Spindle Washer
REPLACEMENT
BEARINGS 6-183 35mm, 42mm, 50mm Spindle Nut
69-94 35mm Bearing Retainer Snap Ring
69-95 42mm Bearing Retainer Snap Ring
69-96 50mm Bearing Retainer Snap Ring
21-84 35mm (Discontinued) Grease cap
(Not designed for water immersion) 21-85 42mm 3-1/16” Grease cap
21-86 50mm 3-5/16” Grease cap

BULK BEARINGS
BEARING# DEXTER# I.D. OF BRG AXLE CAPACITY CUP#
LM11949 NLA 3/4" 2k inner/outer use w/LM11910 cup
L44643 31-31-3 1" 2k inner/outer use w/L44610 cup
L44649 31-31-2 1 1/16" 2k inner/outer & 3.5k outer use w/L44610 cup
LM67048 31-32-2 1 1/4" 4(MH),5.2 & 6k outer use w/L67010 cup
15123 31-29-2 1 1/4" 5.2, 6, & 7k outer use w/15245 cup
14125A 31-17-2 1 1/4" 5.2-7k outer use w/14276 cup
02475 31-28-2 1 1/4" 7.2, 7.5, & 8kouter use w/02420 cup
L68149 31-33-2 1 3/8" 3.5 & 4k(MH) inner use w/L68111 cup
LM48548 31-08-2 1 3/8" inner use w/LM48510 cup
25580 31-30-2 1 3/4" 5.2-9k inner, 9 & 10k outer use w/25520 cup
387A 31-19-2 2 1/4" 9 & 10k inner, 10k outer use w/382A cup
395S 31-22-2 2 5/8" 10k inner use w/394A cup
3984 31-20-2 2 5/8" 12 & 15k inner use w/3920 cup
28682 31-21-2 2 1/4" 12 & 15k outer use w/28622 cup
2585 31-25-2 1.3" 9 & 10k outer (older) use w/2520 cup

DON’T FORGET THE GREASE!!

- SEE PAGES 280-281 OF THIS CATALOG!
6
 BEARING KITS / GREASE & OIL SEALS

WHEEL BEARING KITS

(INCLUDES 2 BEARINGS, 2 RACES, 1 SEAL, 1 DUST CAP)
PART NUMBERS DESCRIPTION
WB750 86767 * LM11949 cone/LM11910 cup for 3/4" straight spindles
WB100 86768 * L44643 cone/L44610 cup for 1" straight spindles*
WB106 86769 * L44649 cone/L44610 cup for 1 1/16" straight spindles
WB125 86771 * LM67048 cone/67010 cup for 1 1/4" straight spindles
WB125T 86772 * LM67048 / 67010 & LM11949 / LM11910 for 1 1/4” x 3/4” step spindles
WB138T 86774 * L68149 & L44649 cones (with cups) for 1 3/8" x 1 1/16" step spindles
WB138EZ L68149 & L44649 cones (with cups) for 1 3/8" x 1 1/16" step spindles
Includes #21-41 EZ-Lube Cap with Plug
WB8-174 25580 & 15123 cones (5 Spoke UTG Hub ) for 1 3/4” x 1 1/4” step spindles
WB8-201 25580 & LM67048 cones (6 Stud Hub) for 1 3/4” x 1 1/4” step spindles
WB8-219 25580 & 14125A cones (8 Stud Hub) for 1 3/4” x 1 1/4” step spindles
* Indicates kits packaged WB8-222 LM67048 & L68149 cones (5 Spoke UTG MotorHome Hub Application)
for retail display.

BLISTER - PACKED BEARING SETS

(ONE CONE & ONE CUP)
PART# DESCRIPTION PART# DESCRIPTION
5502 L44649 cone & L44610 cup 5506 48548 cone & 48510 cup
5503 25580 cone & 25520 cup 5507 LM67048 cone & LM68010 cup
5505 L68149 cone & L68111 cup 5508 14125A cone & 14276 cup
5509 15123 cone & 15245 cup

GREASE & OIL SEALS - BULK

OD X ID OF SEAL
PART# (INCHES) APPLICATION
075-02 1.778 x 1.125 grease, use w/LM11949 inner (3/4" straight spindle)
125-02 2.33 x 150 grease, use w/LM67048 inner (1-1/4" straight or 1-1/4” x 3/4” tapered)
10-1 3.373 x 2.125 single lip grease, use w/25580 inner brg - Dexter 5.2-7k axles
(Can use 10-10 double lip seal)
10-3 1.987 x 1.25 double lip grease, use w/L44643 inner brg (1" straight spindle)
(Can use 10-3DL double lip seal)
10-3DL 1.987 x 1.25 double lip grease, use w/L44643 inner brg (1" straight spindle)
10-4 2.565 x 1.718 grease, use w/L68149 inner brg - Dexter 3.5k axles
(Can use 10-19 double lip seal)
10-9 1.987 x 1.50 grease, use w/L44649 inner brg - Dexter 2k axles
(Can use 10-60 double lip seal)
10-10 3.376 x 2.125 double lip grease, use w/25580 inner brg - Dexter 5.2-7k axles
10-19 2.565 x 1.718 double lip grease, use w/L68149 inner brg - Dexter 3.5k axles
10-40 2.51 x 1.938 grease, use w/68149 inner mobile home axle(MHU)
10-41 2.523 x 1.938 grease, same as above, nylon instead of steel
10-42 2.33 x 1.75 grease, use w/LM67048 inner brg-Dexter 2.8k axles
10-47 3.376 x 2.25 double lip grease, use w/ 25580 inner-Dexter (after 1997)
5.2-7k & non Dexter 6k (= #10-36)
10-48 3.376 x 2.375 double lip oil, use w/ 25580 inner-Dexter 7.5 & 9k "old" style
(up to 10/89) axles
10-51-1 3.88 x 2.875 unitized oil, use w/ 387A inner-Dexter 9 & 10k gd
10-54 3.376 x 2.25 single lip grease, use w/ 25580 inner-Dexter (after 1997)
5.2-7k & non Dexter 6k (can use #10-47 Double Lip Seal)
10-56 4.506 x 3.125 unitized oil, use w/ 395S & 3984 inners-Dexter 10,12, & 15k axles
10-60 1.987 x 1.50 double lip grease, use w/L44649 inner brg - Dexter 2k axles
10-63 3.376 x 2.25 unitized oil, use w/ 25580 inner-Dexter 8k & 9k"old style"
(up to 10/89) axles

BLISTER PACKED SEALS (2/PACK)

PART# BULK SEAL EQUIVALENT PART# BULK SEAL EQUIVALENT
5602 10-3 5605 10-54
5603 10-9 5606 10-1
5604 10-4

7
 GREASE & OIL CAPS • BEARING PROTECTORS

STEEL "PRESS IN" GREASE CAPS

PART# O.D. OF CAP APPLICATION
075-01 1.78" fits hubs with 3/4" outer bearing (LM11949)
21-3 1.98" fits 2 & 3.5k axles w/L44643 or L44649 outer brg
125-01 2.33" fits hubs with 1 1/4" outer bearing (L67048)
21-1 2.44" fits 5.2 & 6k 655 axles w/15123 or 67048 outers
fits 6 & 7k UTG axles w/15123 outer bearings
21-39 2.72" fits 6-7k 865 axles w/14125A outer bearings
fits 7.2 & 8k 865 axles w/02475 outer bearings
21-41 1.98" Cap w/ 85-1 plug - fits same as 21-3, for E-Z lube axles
71-315 1.98" 2 Caps with plugs - Display Packaged on Card
21-41-1 1.98" Cap only, fits same as 21-3, for E-Z lube axles
21-42 2.44" Cap w/ 85-1 plug - fits same as 21-1, for E-Z lube axles
71-317 2.44" 2 Caps with plugs - Display Packaged on Card
21-42-1 2.44" Cap only, fits same as 21-1, for E-Z lube axles
21-43 2.72" Cap w/ 85-1 plug - fits same as 21-39, for E-Z lube axles
71-319 2.72" 2 Caps with plugs - Display Packaged on Card
21-43-1 2.72" Cap only, fits same as 21-39, for E-Z lube axles
85-1 Removable rubber replacement plug for E-Z lube axles
5651 1.98" 2 - 21-3 grease caps (viz pack)
5652 2.44" 2 - 21-1 grease caps (viz pack)

SCREW-ON OIL CAP KITS

(COME COMPLETE WITH 0-RING & PLUG WHERE APPLICABLE)
PART# DESCRIPTION APPLICATION
71-37 Dexter 21-40 oil cap & O-ring 6& 7k oil bath UTG axles
71-38 (1 Pair) Dex. 21-35 oil cap, 10-45 O-ring, 46-32 plug 8-9k oil bath 865 s w axles
71-39 Dexter 21-37 oil cap NLA -use 71-148
71-148 (1 Pair) Dex. 21-36 oil cap, 10-50 O-ring, 46-32 plug 10-15k oil bath axles
71-150 Hayes oil cap, O-ring, & plug, 3.75 OD 9-16k oil bath axles
71-151 AL-KO & Hayes oil cap, O-ring, & plug 8k oil bath axles

BOLT-ON OIL CAP KITS

PART# DESCRIPTION APPLICATION
21-38-2 universal oil cap, 6 bolt, 5 1/2" bolt circle 20-25 air brake axles
71-124 gasket for above cap

BEARING PROTECTION BEARING BUDDIES, BEARING BUDDY COVERS

• Provides permanent protection against damage from
water and dirt entering the wheel bearing.

MODEL NO.* MODEL NO.*OUTER BEARINGOUTER

OUTER BEARING CONE* CUP* BEARIN
BRA#
1781 CONE* OUTER BEARING CUP* LM 11910
LM 11949 17B
1810 1781 LM 67049 LM 11949 LM 12711 LM 1191017B
1938 1810 O9067 LM 67049 O9194, 95, 96 LM 12711
1968 1938 M12649, O7100 O9067 M12610, O7196 O9194, 95, 96
1980A 1968 L 44643, L 44649, L 44640
M12649, O7100 L 44610 19B
M12610, O7196
1980T Threaded
1980A L 44643, L 44649, L 44640L 44649, L 44640 L 44610
L 44643, L 44610 19B
2047 1980T Threaded VariousL 44643, L 44649, L 44640 O7204 L 44610
2240 2047 1700 Series Various 1729 O7204
2328 2240 LM 67048, Hub Not Counterbored
1700 Series LM 67010 1729 23B
2441 LM67048, Hub Counterbored
2328 & others
LM 67048, 15133
Hub Not LM67010, 15245
Counterbored LM 6701023B
2562 2441 48548 Hub Counterbored & others 15133
LM67048, 48510 LM67010, 15245
2717 2562 14124, 14125A 48548 14276 48510
2717 14124, 14125A
* Sizes are hub dust cover bore diameter in inches.
14276

SPINDO-SEAL GREASE SEALING KITS

MODEL NO. USE WITH INNER BEARING SEAL DIAMETER
BBY1 1980 L44643 1.98”
BBY2 1980, 1968 LM48548, L68149 2.56”
BBY5 1980 L44649 1.98”
BBY10 1810 68149 1.718
BBY11 2441 25580 3.38”

8
 TRAILER WHEEL & HUB PARTS

WHEEL STUDS-DRIVE IN
PART# MFG. L =A TL = C K=E TS = D KL = B
7-122 DEX 1 7/8” 1 1/8" 5/8" 1/2" 5/16”
7-123 H/A 2 1/2" 1 1/16" 17/32" 1/2" 9/16"
7-124 H/A 1 13/16” 1 1/4" 9/16" 1/2" 1/2”
7-246 DEX 1 3/4" 1 3/16” 1/2” 1/2” 1/4”
D40368 DICO 2” 1 3/16” 9/16” 1/2” 11/16”
7-132 DEX 2 1/4” 1 1/4” 11/16” 9/16” 1/4”
7-115 DEX 3 1/8” 1 3/4” 11/16” 5/8” 1-1/4”
7-262 DEX 2-1/2” 1-1/8” 9/16” 1/2” 1-3/8”
71-295 same as DEX7-122, 6 per blister card
7-223 9/16” Press-In Stud for Nev-R-Lube Hub
7-224 5/8” Press-In Stud for Nev-R-Lube Hub

WHEEL STUDS-SCREW IN
PART# DESCRIPTION
25-11 9/16"-12 x 9/16-18 (coarse/fine),3.06" length
25-14 1/2"-13x1/2"-20(coarse/fine),DISCONTINUED, use 7-36 instead

WHEEL BOLTS
PART# DESCRIPTION
7-40 1/2"-20 RH thread w/ 13/16"hex, 1 1/4" length
5787 1/2"-20 RH thread w/ 13/16"hex, 1 1/4" length
7-41 9/16"-18 thread w/ 13/16"hex, 1 1/4" length, DISCONTINUED
7-84 9/16”-18 thread RH Hub Bolt

RIM CLAMPS, RIM CLAMP BOLTS

PART# CLAMPS DESCRIPTION
15-2 standard 14.5" open rim clamp, use with all 1/2" or 9/16" wheel bolts or studs
5790 same as 15-2, 5 per blister pack

PART# BOLTS DESCRIPTION

7-36 1/2"-13 RH thread w/ 7/8"hex, 1 5/8" length
5791 1/2"-20 RH thread w/ 7/8"hex, 1 7/8" length, 5 per blister pack
5792 same as 7-36, 5 per blister pack
5793 1/2"-13 RH thread w/ 7/8"hex, 2 5/16" length

REPLACEMENT WHEEL NUTS

PART# DESCRIPTION
5580R 7/16"-20RH conical seat wheel nut, 60' taper, 3/4" hex
6-80 1/2"-20RH conical seat wheel nut, 60' taper, 13/16" hex
6-12 1/2"-20RH flat face, rim clamp nut, 7/8"hex
6-53 9/16"-18RH conical seat wheel nut, 60' taper, 7/8"hex
6-5 9/16"-18RH flat face, rim clamp nut, 7/8"hex
5892 9/16"-18RH 1 pc. flat flanged wheel nut, 7/8" hex
4975R/L 5/8"-18RH or LH conical seat wheel nut, 90' taper, 1 1/16" hex
5652R/L 3/4"-16RH or LH conical seat wheel nut, 1 1/2" hex
7895R/L 3/4" -16 inner thread x 1 1/8"-16 outer thread RH or LH "inner Budd" nut
5552R/L 1 1/8"-16 RH conical seat "outer Budd" nut, 1 1/2" hex
39946 5/8”-18 RH 2-piece swivel nut for hub-piloted wheels

WHEEL MOUNTING PLATES-TRUCK AND TRAILER

PART# DESCRIPTION
33-52-1 Wheel clamping plate for dual type trailer wheels, 8 hole- 6 1/2" bolt circle
(use E4975R/L lug nuts with this clamping plate).
Also used with GM/Chevy 16” and 16.5” dual wheels

9
 SUSPENSION PARTS • SPRINGS, HANGERS

DOUBLE EYE SPRINGS

PART # MAX.CAP.EA.(LBS.) LENGTH WIDTH # OF LEAFS
72-16 700 21” 1 3/4” 3
933611 750 27” 1 3/4” 3
72-17 1000 21” 1 3/4” 3
933612 1000 27” 1 3/4” 3
LENGTH EQUALS
72-22 1250 25 1/4” 1 3/4” 3
EYE TO EYE
72-224 1250 30” 1 3/4” 3
72-167 1400 20 1/2” 1 3/4” 4
72-23 1500 25 1/4” 1 3/4” 3
Double Eye Springs 72-9 1750 23.5” 1 3/4” 3
Are Supplied Complete 933613 1750 27” 1 3/4” 4
With (2) #14-1 Bushings Installed 72-24 2000 25 1/4” 1 3/4” 3
72-051 NEW! 2000 26” 1 3/4” 4
72-022 NEW! 2480 30” 1 3/4” 6
72-079 NEW! 2500 23.13” 1 3/4” 4
72-115 3000 25 1/2” 1 3/4” 1 (Mono-Leaf)
72-26 3000 25 1/4” 1 3/4” 4
72-111 NEW! 3000 25 1/4” 1 3/4” 5
933617 3000 27” 1 3/4” 6
72-223 NEW! 3380 25 1/4” 1 3/4” 6
72-27 3500 25 1/4” 1 3/4” 6

RADIUS / FLAT END SLIPPER SPRINGS

LENGTH EQUALS
EYE TO END PART # MAX.CAP.EA.(LBS.) LENGTH WIDTH # OF LEAFS
72-3 (Flat) 750 25” 1 3/4” 3
72-026 (Radius) NEW! 1000 20 3/4” 1 3/4” 3
72-2 (Radius) 1000 27” 1 3/4” 2
Radius/Flat End Springs 72-179 (Radius) NEW! 1000 24.62” 1 3/4” 4
Are Supplied Complete 72-016 (Flat) NEW! 1184 25.13” 1 3/4” 5
With (1) #14-1 Bushing Installed 72-039 (Flat) 1430 30” 1 3/4” 3
72-047 (Flat) NEW! 1653 24 1/2” 1 3/4” 3

LENGTH EQUALS
EYE TO END HOOK END SLIPPER SPRINGS
PART # MAX.CAP.EA.(LBS.) LENGTH WIDTH # OF LEAFS
Hook End Springs 72-29 1500 27” 2” 4
Are Supplied Complete 72-31 2500 27” 2” 4
With (1) #14-78 Bushing Installed 72-32 3500 27” 2” 5

LENGTH EQUALS
EYE TO EYE OPEN EYE SLIPPER SPRINGS
PART # MAX.CAP.EA.(LBS.) LENGTH WIDTH # OF LEAFS
72-263 1725 27” 1 3/4” 3
Open Eye Springs Are Supplied 72-264 2250 27’ 1 3/4” 4
With (1) #14-76 Bushing Installed. 72-265 2500 27” 1 3/4” 5
Please Order Open End Bushing
#14-76 Separately

SPRING HANGERS FOR 1 3/4” DOUBLE EYE SPRINGS

note: all of these hangers are drilled for 9/16”spring bolts
PART # DESCRIPTION BOLT HOLE TO BRACKET TOP
28-5 front, center, or rear hanger 3 1/4”
28-6 short front hanger, single axle only 1 1/2”
30-20 rear hanger, single axle only 1 5/16”

SPRING HANGERS FOR 2” SLIPPER SPRINGS

PART # DESCRIPTION BOLT HOLE TO BRACKET TOP
28-1 front hanger 4 1/4”
29-1 center hanger, tandem slipper 3 1/2”
30-28 rear hanger, 3/8” keeper bolt 5 1/4”

28-3
GALVANIZED HANGERS FOR 1-3/4” SLIPPER SPRINGS
28-4 PART # DESCRIPTION
28-3 galvanized rear hanger, slipper spring
28-4 galvanized front hanger, slipper spring

10
 SUSPENSION PARTS • HANGER KITS

HANGER KITS FOR DOUBLE EYE SPRINGS

PART # DESCRIPTION
AP122/H104 Single axle trailers (up to 7k axles), 1 3/4” double eye springs
contains: (2)- 28-5 front hangers (2)- 30-20 rear hangers
(6)- 7-3 9/16” suspension bolts (6)- 6-7 9/16” suspension nuts
(4)- 18-12 shackle arms
AP233/H248 Tandem axle trailers (up to 7k axles), 1 3/4” double eye springs
contains: (6)- 28-5 hangers (all) (2)- 13-104-2 equalizers
(14)- 7-3 9/16” suspension bolts (14)- 6-7 9/16” suspension nuts
(8)- 18-11 shackle arms
AP234/H248 (for 36” Axle Spacing) Tandem axle (up to 7k axles), 1 3/4” double eye springs
contains: (6)- 28-5 hangers (all) (2)- 13-11 equalizers
(14)- 7-3 9/16” suspension bolts (14)- 6-7 9/16” suspension nuts
(8)- 18-12 shackle arms
AP335/H348 Triple axle trailers (up to 7k axles), 1 3/4” double eye springs
contains: (8)- 28-5 hangers (all) (2)- 13-104-2 equalizers
(2)- 13-105-2 equalizers (22)- 7-3 9/16” suspension bolts
(22)- 6-7 9/16” suspension nuts (12)- 18-11 shackle arms

HANGER KITS FOR SLIPPER SPRINGS

PART # DESCRIPTION
AP115/H115 single axle trailer, 1 3/4” wide slipper springs
contains: (2)- 28-39 front hangers (2)- 30-37 rear hangers
(2)- 7-126 suspension bolt (2)- 6-92 suspension nut
AP103/H110 single axle trailer (up to 8k axles), 2” wide slipper springs
contains: (2)- 28-1 front hangers (2)- 30-28 rear hangers
(2)- 7-17 suspension bolt (2)- 6-7 suspension nut
(2)- 7-7 keeper bolt (2)- 6-11 keeper nut
AP202/H202 tandem axle trailer (up to 8k axles), 2” wide slipper springs
contains: (2)- 28-1 front hangers (2)- 29-1 center hangers
(2)- 30-28 rear hangers (2)- 13-4 equalizers
(4)- 7-17 suspension bolt (4)- 6-7 suspension nut
(4)- 7-7 keeper bolt (4)- 6-11 keeper nut
(2)- 7-1-1 equalizer bolt (2)- 6-111 equalizer bolt nut
AP202/H216 (for 36” Axle Spacing) tandem axle trailer (up to 8k axles), 2” wide slipper springs
contains: (2)- 28-1 front hangers (2)- 29-1 center hangers
(2)- 30-28 rear hangers (2)- 13-44 equalizers
(4)- 7-17 suspension bolt (4)- 6-7 suspension nut
(4)- 7-7 keeper bolt (4)- 6-11 keeper nut
(2)- 7-1-1 equalizer bolt (2)- 6-111 equalizer bolt nut

SPINDLES, SPINDLE WASHERS, SPINDLE NUTS

PART # SPINDLE DESCRIPTION FITS
2-160-1 1" Straight Spindle Assy., 2000 lb. axles 1 1/4" I.D. Tube
2-160-4 1 1/16" Straight Spindle Assy., 2000 lb. axles 1 1/4" I.D. Tube
Removable Spindle 80323 1 1/16" Replacement Removable Straight Spindle for Tie-Down, Torflex 2K Axles
2-162-7 1 3/8"-1 1/16" Step Spindle Assy., 3500 lb. axles 1 3/4" I.D. Tube
2-162-22 1 3/8"-1 1/16" E-Z Lube Step Spindle Assy., 3500 lb. axles 1 3/4" I.D. Tube
2-3DF 1 3/8"-1 1/16" 4Inch-Drop Step Spindle Assy., 3500 lb. axles 1 3/4" I.D. Tube
Removable Spindle 80324 1 3/8"-1 1/16" Replacement Removable Step Spindle for Tie-Down, Torflex 3.5K Axles
2-161-7 1 3/4"-1 1/4" Step Spindle Assy., 5.2-7K axles 2 1/4" I.D. Tube
Removable Spindle 80062A 1 3/4"-1 1/4" Replacement Removable Step Spindle for Tie-Down, Torflex 5.2-7K Axles
2-MH-1 1 3/8"-1 1/4" Step Spindle Assy., For Motor Home Axle Applications (NLA as of 2012)
Note: The above are complete with nut & washer (where necessary)

PART# WASHER DESCRIPTION PART# SPINDLE NUT DESCRIPTION

5-22 round washer, 3/4" ID, 2k-6k axles 6-1 6 slot castle nut, 1"-14 thread, 2k-9k axles
5-23 "D" style washer, 1" ID, 2k-6k axles 6-2 6 slot castle nut, 3/4"-14 thread, 2k-9k axles
5-27** round washer, 1" ID 2k-6k axles 6-176 12 slot castle nut, 1"-14 thread, 2k-9k axles -
5-101 tang washer for Dexter E-Z lube 2k-7k DISCONTINUED, Use 6-1
5774 one round washer & one castle nut, 19-2 spindle nut cotter pin - 1/8” x 1.75” length
1"-14 spindle thread -viz pack 6-84 spindle nut, 1 3/4"-12 thread, 10k-15 axles
5-101 5775 one "D" style washer & one castle nut, 6-190 new style retainer - use with 6-191
Tang Washer 1"-14 spindle thread-viz pack 6-191 new style jam nut - use with 6-190
5-57 "D" style washer, 2 1/2" OD x 1"ID, 6-9k Dexter axles
6-190 5-59 tang washer, 1 3/4" ID, Dexter 12-15k
Retainer 5-60 keyed washer, 1 3/4"ID for 1 3/4"-12 spindle, 10-15k axles
**note : 1" keyed or "tongue" washer NLA, use round washer in its place
11
 SUSPENSION PARTS • CONVERSION KITS

HD SUSPENSION KIT 71-358 For 1 3/4” wide, double eye springs- single axles
PART NO. QUANTITY DESCRIPTION
006-092-01 6 Locknut
007-187-00 2 Step Bolt Wet
014-077-00 4 Bronze Bushing
018-022-01 2 Shackle Link
018-027-01 2 Shackle Link Assembly
059-547-00 1 Instruction Sheet

HD SUSPENSION KIT 71-359 For 1 3/4” wide, double eye springs - tandem axles, 33” axle spacing

PART NO. QUANTITY DESCRIPTION

006-092-01 14 Locknut
007-126-00 2 Bolt
007-187-00 4 Step Bolt Wet
014-077-00 8 Bronze Bushing
013-104-04 2 Equalizer
018-024-01 4 Shackle Link
18-26 4 Shackle Link Assembly
059-547-00 1 Instruction Sheet

HD SUSPENSION KIT 71-360 For 1 3/4” wide, double eye springs - triple axles, 33” axle spacing
PART NO. QUANTITY DESCRIPTION
006-092-01 22 Locknut
007-126-00 4 Bolt
007-187-00 6 Step Bolt Wet
013-104-04 2 Equalizer
013-105-04 2 Equalizer
014-077-00 12 Bronze Bushing
018-024-01 6 Shackle Link
18-26 6 Shackle Link Assembly
059-547-00 1 Instruction Sheet

HD SUSPENSION KIT 71-448 For 1 3/4” wide, double eye springs - tandem axles with 4” high equalizer

PART NO. QUANTITY DESCRIPTION

006-092-01 14 Locknut
007-126-00 2 Bolt
007-187-00 4 Step Bolt Wet
013-010-04 2 Equalizer
014-077-00 8 Bronze Bushing
018-024-01 4 Shackle Link
018-026-00 4 Shackle Link Assembly
059-047-00 1 Instruction Sheet

HD SUSPENSION KIT 71-449 For 1 3/4” wide, double eye springs - tandem axles, 35” axle spacing
PART NO. QUANTITY DESCRIPTION
006-092-01 14 Locknut
007-126-00 2 Bolt
007-187-00 4 Step Bolt Wet
013-122-04 2 Equalizer
014-077-00 8 Bronze Bushing
018-024-01 4 Shackle Link
018-026-00 4 Shackle Link Assembly
059-047-00 1 Instruction Sheet

OVER / UNDER CONVERSION KITS 71-384 For 2-3/8” tube 71-385 For 3” tube
KIT #71-384 PART NO. QUANTITY DESCRIPTION
003-062-00 2 Spring Seat
006-017-01 8 Nut
011-074-00 4 U-Bolt
012-051-00 2 Tie-Plate
KIT #71-385
003-063-00 2 Spring Seat
006-129-01 8 Nut
011-017-00 4 U-Bolt
012-001-00 2 Tie-Plate
12
 SPRINGS SEATS • U-BOLTS

AXLE SPRING SEATS (PERCHES)

PART# DESCRIPTION
3-49 weld-on seats for 1 3/4" tubular axle (Dexter 2k)
3-43 weld-on seats for 2 3/8" tubular axle (Dexter 2.8-3.5k)
3-42 weld-on seats for 3" tubular axle & 1 3/4" wide springs (Dexter 5.2-7k)
3-1 weld-on seats for 3" tubular axles & 2" wide springs (Dexter 5.2-7k)
19070G Galvanized! 19070G bolt-on galvanized seats for 2" square axles

AXLE SPRING PLATES ALL HAVE 6" LENGTH X 3 3/4" WIDTH

PART# DESCRIPTION
12-1* use with 3" tubular axle & 1 3/4" wide double eye springs
12-2* use with 3" tubular axle & 2" wide slipper springs
12-188 12-3 use with 1 7/8” square U-bolts, 2 3/8" tubular axle & 1 3/4" wide double eye springs
12-4* use with 2 3/8" tubular axle & 2" wide slipper springs
12-40 use with 1 3/4" tubular axle & 1 3/4" wide double eye springs
12-188 Galvanized 5" x 3-3/4" Plate Fits 2" Square Axle Only & 1-3/4" spring.
Galvanized! (use with 11-124 or 11-125 square U-bolts)
*note : can also use 12-2 & 12-4 with 2 -3/16" square U-bolts & 12-1 with 3-1/16" square U-bolts

REPLACEMENT ROUND BEND U-BOLTS

(ALL U-BOLTS COME WITH NUTS)
PART# TUBE SIZE (THREAD) A B C13/8” 11-
11-380 3/8” ZINC 1.5" 2.25"
86224 1 3/4" 3/8” GALV 4-13/16" 3/8"-24
11-54 1 3/4" 3/8” 4.03" 3/8"-24 1 1/2”
11-21 2 3/8" 1/2” 5.13" 1/2"-20 2"
11-22 2 3/8" 1/2” 6.25" 1/2"-20 2"
11-18 3" 1/2” 7.05" 1/2"-20 2"

REPLACEMENT SQUARE BEND U-BOLTS

(ALL U-BOLTS COME WITH NUTS)
PART# DESCRIPTION A. B. PART# DESCRIPTION A. B.
11-380 3/8” Zinc 1.5” 2.25” 11-124 1/2” Zinc 1-7/8” 4-1/2”
11-381 3/8” Zinc 2.06” 4.25” 11-122 1/2” Zinc 2.06” 3.50”
11-386 3/8” Zinc 3-1/16” 3.00” 11-123 1/2” Zinc 2.06” 4.812”
86227 3/8” Galv 1-5/8” 3-9/16” 11-125 1/2” Zinc 2-1/16” 5-1/2”
86220 7/16” Galv 1-9/16” 3-9/16” 11-126 1/2” Zinc 3.06” 3.81”
86221 1/2” Galv 1-9/16” 4-1/16” 11-127 1/2” Zinc 3.06” 5.35”
86222 1/2” Galv 3-1/16” 3-13/16” 11-128 1/2” Zinc 3.06” 6.25”
86223 1/2” Galv 2-1/16” 4-13/16” 11-129 1/2” Zinc 3.06” 7.06”
86225 1/2” Galv 2-3/8” 5-3/8” 86222 1/2” Galvanized 3.06” 3.81”
86226 1/2” Galv 3-1/16” 6-11/16” 86223 1/2” Galvanized 2.06” 4.81”

U-BOLT NUTS
PART# DESCRIPTION
6-67 3/8"-24 thread, flanged lock nut
6-46 1/2"-20 thread, nylock zinc-plated lock nut
6-92 7/16" thread, flanged U-bolt nut

U-BOLT KITS (INCLUDE 4 U-BOLTS, 8 NUTS, & 2 PLATES)

KITS FOR 1-3/4” WIDE SPRINGS
PART# DESCRIPTION
2-1/16” Zinc U-2 kit for 2k, 1 3/4" tubular axle (includes 4- 11-54, 8- -67, 2- 12-40)
Square Bend U-3 kit for 3.5k, 2 3/8" tubular axle (includes 4- 11-21, 8- 6-46, 2- 12-3*)
#86783 Display-Pack U-6 kit for 6k & 7k, 3" tubular axle (includes 4- 11-18, 8- 6-46, 2- 12-1**)
for 2” square axles 86783 Display-Packaged kit for 2” square axle
Includes 2 galvanized plates, 4- 11-125 zinc square U-bolts, & 8- 6-46 nuts.

KITS FOR 2” WIDE SPRINGS

PART# DESCRIPTION
U-3/2 kit for 3.5k, 2 3/8" tubular axle (includes 4- 11-21, 8- 6-46, 2- 12-4)
U-6/2 kit for 6k & 7k, 3" tubular axle (includes 4- 11-18, 8- 6-46, 2- 12-2)
13
 SUSPENSION PARTS • EQUALIZERS

SUSPENSION BOLTS & NUTS

PART# DESCRIPTION
7-3 9/16"-18 x 3" length, 3/4" hex bolt, use with 1 3/4"wide springs
7-187 9/16"-18 x 3" length 3/4" hex bolt w/ zerk fitting, use with 1 3/4"wide springs
7-17 9/16"-18 x 3 1/2" length 3/4" hex bolt, use with 2" wide springs
7-126 7/16"-20 x 2.9" length, 3/4" hex shoulder-bolt, w/ 9/16" body, use w/ 1 3/4" springs
6-92 7/16"-20 flanged nut for 7-126 shoulder-bolt
6-7 9/16"-18" locknut for all 9/16" suspension bolts
7-1-1 7/8" equalizer carriage bolt w/ 6-111 6-slot castle nut
7-7 5/16" spring keeper bolt w/6-11 nut, used on 2" slipper spring rear bracket

SHACKLE STRAPS (OR LINKS)

PART# A B C
18-11 2 1/4" 3 1/2" 1 1/4"
18-12 3 1/8" 4 3/8" 1 1/4"
18-115 2-9/16” 3-3/16” 1 1/4"
18-24-1 (HD) 2.25” 3.81” 1.375”
18-26 (HD - with 2 bolts) 2.25” 3.81” 1.375”

SPRING BUSHINGS
PART# DESCRIPTION
14-1 9/16"ID x 11/16" OD nylon, 1 3/4" overall length
14-77 9/16"ID x 11/16" OD bronze, 1 3/4" overall length
14-54 9/16"ID x 1 1/4" OD nylon, 2" overall length (2" slipper type)
14-75 1/2"ID x 11/16" OD nylon, 2" overall length
14-76 9/16”ID x 1 1/32" OD nylon, 1 3/4" overall length
(Used on eye ends of double eye and slipper springs)
14-78 9/16"ID x 11/16" OD nylon, 2" overall length (2" slipper type)
14-79 9/16"ID x 7/8" OD nylon, 1 3/4" overall length
14-69 1"ID x 2 1/16" OD rubber/steel, 3 1/8" overall length (HD application )

SUSPENSION EQUALIZERS
PART# TYPE DESCRIPTION A B C
13-10 DE 9/16" nylon bushed 6" 5" 5"
13-11 DE 9/16" nylon bushed, XL 7 7/8" 3" 4 7/8”
13-104-2 DE most common DE type, 9/16" nylon bushed 5 5/8” 2" 3 3/8”
A
13-104-3 DE same as 13-104-2 w/ zerk fitting & bronze bushing 5 5/8" 2" 3 3/8"
13-105-2 DE front equalizer, triple axle setup, 9/16" nylon bushed 7" 1" 3 1/2"
13-40EQ 13-4 SL most common slipper type, 7/8" center hole 11 1/4" 4 7/8" 4 3/4”
13-40EQ CL straight center-line type,1-3/4” width, 9/16" center hole 5-1/2" N/A N/A
13-44-1 SL 7/8" center hole, XL 13 1/8" 6 3/8" 6 3/4"
13-38EQ SL for reverse slipper springs, on E-Z Load'r trailers 8 3/4" 3 1/2" 3 1/2"
(rubber bushed 9/16" center hole)
13-6 SL special order only, XXL slipper type 26 1/2" 12 1/8" 12"

TRAILER REPLACEMENT SHOCK ABSORBER

PART# DESCRIPTION
52-3 Trailer Shock with Threaded Stud on each end

STD# TYPE DESCRIPTION A B C

13-104-2 DE most common DE type, 9/16" nylon bushed 5 5/8” 2" 3 3/8”
UPGRADES TO E-Z FLEX EQUALIZER #13-143-3
13-11 DE 9/16" nylon bushed, XL 7 7/8" 3" 4 7/8”
UPGRADES TO E-Z FLEX EQUALIZER #13-144-3

BRAKE MOUNTING FLANGES

PART# DESCRIPTION
4-34 K flange, 4 hole, 4" bolt circle for 2" tubular axle, 1.64" pilot hole
4-35 K flange, 4 hole, 4" bolt circle for 2 3/8" tubular axle, 2.27" pilot hole
4-44-1 B flange, 5 hole, 3.88" bolt circle for 3" tubular axle, 2.75" pilot hole

14