Scribd
Upload
188 views1 page

Unistrut Opm 0295 13 (Page 5c 1)

This document provides information on 45° fixed angle fittings and hinged fittings for strut and telespar braces, including: - Material and finish specifications for the fittings. - Dimensions and design load capacities for various 45° fixed angle fittings. - Dimensions and design load capacities for hinged fittings at various angles. - Notes on bolt and nut specifications and connection requirements.

Uploaded by

jeffuang
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
188 views1 page

Unistrut Opm 0295 13 (Page 5c 1)

This document provides information on 45° fixed angle fittings and hinged fittings for strut and telespar braces, including: - Material and finish specifications for the fittings. - Dimensions and design load capacities for various 45° fixed angle fittings. - Dimensions and design load capacities for hinged fittings at various angles. - Notes on bolt and nut specifications and connection requirements.

Uploaded by

jeffuang
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Brace Fittings

9;7-8.;<&[&W.6./:&,>-1.51;7.36/
#I"2%&WE!!EGJ,&C&G%_&EG,!"$$"!EFG,
All Fittings on this Page
45° FIXED ANGLE FITTINGS Material: ASTM A1011 SS GR 33 min. or
ASTM A1011 HSLAS GR 45 min.
Finish: ASTM B633 Type III SC1 (EG)
P3810-050 P3815-050
Design Load
FOR STRUT BRACE FOR TELESPAR BRACE Design Load = 1,397 lbs
= 1,397 lbs
(Capacity of Fitting)
0.36” Dia (2X)
0.11” Projection
3 7/16" 45° FP = 985 lbs
3 7/16"
7
/16” Dia 11
/16"
45°
45°
2 5/16" FP = 985 lbs 1"
2 5/16"
1"
1 1/16" 1 1/16"
9
/16” Dia, Typ 9
/16” Dia, Typ

HINGED FITTINGS Fittings: P1354AW, P3835-050


Angle Design
P1354AW FP
P3835-050
OPM-0295-13 Q"R&4830& $3;=
FOR STRUT BRACE (lbs)
FOR TELESPAR BRACE Horizontal (lbs)
Design Load
+5°
Design Jeffrey Y. Kikumoto
30° / -25° 2,136 1,850
Load 0.36” Dia (2X) 45° +5°
/ -10° 1,397 985
4" 0.11” Projection
A 60° +0°
/ -10° 1,462 730
7 4"03/02/2020
3 /16” Dia 11
/ "
2 /16" 16
FP
A
45° 2 3/16" 1"
FP
9
/16” Dia, 1"
Typ
Fittings: P1354AW, P3835-050
9
/16” Dia,
3
Typ
/16” Factory
3
13 Weld /16” Factory
/16" 0° - 89°
13
/16" Weld
0° - 60°

Acceptable Not Acceptable


Note:
1) Loads based on ½” HHCS or HSSB Bolt, and ½” Channel Nut.
G+! ]''!6//-%;!"3%%&"/-3%*!/3!*/?C/!.C*/!"3%53?.!/3!3%&!35!/#&!0&/$-'*!-%!7&"/-3%!T$K!]''!#3'&*!-%!&$"#!6//-%;!.C*/!#$A&!3%&!35!
these connections unless otherwise noted in the above details. Other components are hidden on this page for clarity.
3) Fitting dimensions (all this page) unless otherwise noted: Hole Diameter: 9e16”; Hole Spacing - From End: 13e16”; Hole
Spacing - On Center: 1 7/8”; Width: 1 5/8”; Thickness: 1/4” or 0.22”.
4) P3815-050 and P3835-050 are to be connected to Telespar per Page 5a.8 and capacities on that page may govern.

Page:
16100 S. Lathrop Ave
Harvey, IL 60426

Unistrut
Toll-Free: (800) 882-5543 Structural Engineer: Rami Elhassan 5c.1
California SE No. 3930
www.unistrutseismic.com

02/27/2020 OPM-0295-13: Reviewed for Code Compliance by Jeffrey Kikumoto 93 of 151

You might also like