The Microscope Parts and Use

Name: Shelo Marie Garcia

Section: STEM-15
Historians credit the invention of the compound microscope
to the Dutch spectacle maker, Zacharias Janssen, around
the year 1590. The compound microscope uses lenses
and light to enlarge the image and is also called an optical
or light microscope (vs an electron microscope). The
simplest optical microscope is the magnifying glass and is
good to about ten times (10X) magnification. The
compound microscope has two systems of lenses for
greater magnification, 1) the ocular, or eyepiece lens that
one looks into and 2) the objective lens, or the lens closest
to the object. Before purchasing or using a microscope, it is
important to know the functions of each part.

Eyepiece Lens: the lens at the top that you look through.
They are usually 10X or 15X power.

Draw Tube and Body Tube: Connect the eyepiece to the

objective lenses

Arm: Supports the tube and connects it to the base. It is

used along with the base to carry the microscope

Base: The bottom of the microscope, used for support

Illuminator: A steady light source (110 volts) used in place of a mirror.

Stage: The flat platform where you place your slides. Stage clips hold the slides in place.

Revolving Nosepiece or Turret: This is the part that holds two or more objective lenses and can be rotated to
easily change power.

Objective Lenses: Usually you will find 3 or 4 objective lenses on a microscope. They almost always consist of
4X, 10X, 40X and 100X powers. When coupled with a 10X (most common) eyepiece lens, we get total
magnifications of 40X (4X times 10X), 100X, 400X and 1000X. The shortest lens is the lowest power, the longest
one is the lens with the greatest power. The high power objective lenses are retractable (i.e. 40XR). This means
that if they hit a slide, the end of the lens will push in (spring loaded) thereby protecting the lens and the slide.

Rack Stop: This is an adjustment that determines how close the objective lens can get to the slide. It is set at
the factory and keeps students from cranking the high power objective lens down into the slide and breaking
things.

Diaphragm or Iris: Many microscopes have a rotating disk under the stage. This diaphragm has different sized
holes and is used to vary the intensity and size of the cone of light that is projected upward into the slide. There is
no set rule regarding which setting to use for a particular power. Rather, the setting is a function of the
transparency of the specimen, the degree of contrast you desire and the particular objective lens in use.

Coarse adjustment: This is used to focus the microscope. It is always used first, and it is used only with the
low power objective.
Fine adjustment: This is used to focus the microscope. It is used with the high power objective to bring the
specimen into better focus.

How to Focus Your Microscope: The proper way to focus a microscope is to start with the lowest power
objective lens first and while looking from the side, crank the lens down as close to the specimen as possible
without touching it. Now, look through the eyepiece lens and focus upward only until the image is sharp. If you
can’t get it in focus, repeat the process again. Once the image is sharp with the low power lens, you should be
able to simply click in the next power lens and do minor adjustments with the fine adjustment knob. If your
microscope has a fine focus adjustment, turning it a bit should be all that’s necessary. Continue with subsequent
objective lenses and fine focus each time. Note: Both eyes should be open when viewing through the microscope.
This prevents eye fatigue, which occurs when the nonviewing eye is kept closed. Keeping both eyes open does
take some practice, but it is highly recommended. Also, you should never let your eye touch the ocular lens. If
your eyelashes touch the lens you are to close. Always remove eyeglasses when viewing through a microscope.
If your eyeglass lens touches the microscope it may get scratched.
9
Making a wet mount slide Procedure:
1. Place a clean slide on a paper towel on the lab table. Handle slides at the ends, not the center, to avoid
getting fingerprints in the viewing area of the slide.
2. Place a drop of water on the center of a clean dry slide
3. Using the tweezers, place the specimen in the middle of the drop.
4.While holding the cover slip upright, carefully place one edge of
the cover slip next to the water. Hold the coverslip by the edges to
avoid fingerprints. Set one edge against the slide and lower it until it
contacts the liquid. The liquid should spread across the whole area
of the coverslip. Slowly lower the upper edge of the cover slip onto
the water. The objective is to minimize or eliminate air bubbles
under the cover slip. You might find it helpful to use one toothpick to
hold the lower edge in place, while using another to carefully lower
the slip into place.
5. An absorbent towel can be placed at the edge of the cover slip to draw out some of the water, further flattening
the wet mount slide.
6. Never view a slide without a coverslip. The coverslip protects the objective lens from the liquid on the slide.

How To Stain a Slide:

7. Place one drop of Methylene Blue stain on one edge of the coverslip, and
the flat edge of a piece of paper towel on the other edge of the coverslip.
The paper towel will draw the water out from under the coverslip, and the
cohesion of the water will draw the stain under the coverslip.
2. As soon as the stain has covered the area containing the specimen you are finished. The stain does not
need to be under the entire coverslip. If the stain does not cover the area needed, get a new piece of paper towel
and add more stain until it does.
3. Be sure to wipe off the excess stain with a paper towel, so you don’t end up staining the objective lenses.
4. You are now ready to place the slide on the microscope stage. Be sure to follow all the instructions on the
previous pages as to how to use the microscope.
5. When you have completed your drawings, be sure to wash and dry both the slide and the coverslip and
return them to the correct places!
6. All slides must be put away in the proper trays! Students will not leave until all materials have been put way
properly. You are a team!
7. Remember – You break it you buy it!!! The microscopes you are using have a replacement cost of
about Php 32, 000. (CASH ONLY – NO CHECKS) Be very careful. Keep the power cords and
microscopes at least 6 inches away from the edge of the counter.
Microscope Parts and Use
Worksheet
Name: Shelo Marie Garcia
14 Section: STEM-15
 7
1 1 8
8 COARSE BODY TUBE
ADJUSTMENT
2 9 KNOB
2 9
3 10 FINE ADJUSTMENT REVOLVING
KNOB NOSEPIECE OR
4 11 TURRET
3 10
ARM LOW POWER
12 OBJECTIVES
5 4 11
13 STAGE CLIPS HIGH POWER
OBJECTIVES
6 14 5 12
INCLINATION STAGE
JOINT
3 6 13
BASE CONDENSER
7 14
EYEPIECE LENS MIRROR
ILLUMINATOR

1
1. Explain an important thing to remember as you turn the high power objective into place.

-The high-power objective lens is retractable, so when you strike a slide, the end of the lens will push in (spring
loaded), protecting the lens and the slide.

2. What should you always remember when you use the coarse adjustment?

-It is always used first, and it is used only with the low power objective.

3. Under what conditions would you adjust the diaphragm?

-Because the Diaphragm has varied diameter holes, it may alter the intensity depending on the size of the light
cone pushed upwards into the slide.

4. What should you always remember when handling microscope slides?

-To avoid fingerprints in the viewing area of the microscope slide, always

handle it from the ends rather than the middle. Furthermore, a coverslip

should always be used when viewing a slide since it protects the

objective lens from the specimen on the slide.

5. What is the purpose of the stage clips?

-Their purpose is to hold the slides in place

6. In terms of your eyes, what should you try to learn as you use the
microscope?

-We must keep both eyes awake at all times to avoid eye tiredness. If you're wearing

glasses, it's best not to let them strike the eyepiece lens because they'll get scratched, or

you'll have to remove them when looking through the microscope. Furthermore, we must

make certain that our eyelashes do not come into contact with the lens.

7. What are the two parts used to carry the microscope?

-The base and arm are the two elements that are utilized to transport the microscope.

We must carry the microscope with both hands so that it does not fall out of our hold.

8. What is the purpose of the coverslip?

-Its purpose is to protect the objective lens from the liquids.

9. What is the objective lens used to locate the specimen and first focus?

-The course adjustment knob is the objective lens that is used to locate the specimen and first focus. It's the first to
only be used with low-power objective lenses.

10. What are the chemicals called that are sometimes used to make the specimens visible?

-Chemicals like Methylene Blue are used to make specimens visible.

11. What should you do if the high power objective lens touches or breaks the coverslip?

-Inform your teacher/instructor/professor as soon as possible.