Centrifugal Pump Data Sheet Issue Date

Rev No.:_________ Rev Date:_____________________ November 2019

ASME B73 ASME Centrifugal Pumps (US Customary Units) Page 1 of 4

ASME B73.1, ASME B73.2
Usage key - data provided by: Purchaser Supplier Supplier if not by purchaser

1 Issued for: Proposal Purchase As built

2 Facility name / location: P&ID number:
3 Item name: Purchaser / location:
4 Item tag number: Job number:
5 Service: Purchaser order number:
6 Unit: Supplier / location:
7 Number of pumps required: Supplier order / serial numbers: /
8 GENERAL
9 Pump size: Driver item number:
10 Pump model: Driver provided by:
11 Pump type: Horizontal End Suction Vertical In-line Repeller Driver mounted by:
12 Recessed Impeller Self Priming Low Flow Variable speed operation YES NO
13 Operating Conditions Performance
14 Rated Maximum Normal Minimum Other Performance curve number:
15 Flow: (gpm) Speed: (rpm) B73 curve speed Job driver nameplate
1
16 At flow designated above Maximum differential head @ rated impeller: (ft)
1 3
17 Head : (ft) at specified flow Rated Maximum Normal Minimum Other
18 NPSHA1: (ft) Head3: (ft)
19 Suct pres1: (psig) NPSHR3: (ft)
20 Speed(if variable)3: (rpm)
21 System design: Minimum continuous stable flow: (gpm)
22 Suction pressure: min. / max.: / (psig) Allowable operating region: to: (gpm)
23 Suction temperature: min. / max.: / (°F) Best efficiency point for rated impeller: (gpm)
24 Stand alone operation Suction specific speed:
25 Parallel operation with item no.: Impeller diameter Rated: Max: Min: (in)
26 Series operation with item no.: Pump rated power: (BHP) Efficiency: (%)
27 Service: Maximum power with rated impeller: (BHP)
28 Continuous Intermittent: starts/day Case pressure rating:

29 System control method: Maximum allowable working pressure: (psig) @ (°F)

30 Speed Throttle System Resistance Only Hydrostatic test pressure: (psig)
31 Site Conditions and Utilities
32 Pumped Fluid Location: Indoor Outdoor Altitude: (ft)
33 Pumped fluid: Range of ambient temperatures: min. / max.: / (°F)
34 Rated Maximum Normal Minimum Area classification: Nonhazardous
35 Pumping temperature: (°F) Cl: Div or Zone: Gr: T Code:
2
36 At pumping temperatures designated above Electricity Voltage Phase Hertz
2
37 Specific gravity : Drivers
2
38 Vapor pressure : (psia) Heating
2
39 Viscosity : (cP) Cooling water: Source:
2
40 Specific heat : (Btu/lb °F) Supply temp.: (°F) Max. return temp.: (°F)
41 Atm pressure boiling point: (°F) @ (psia) Supply pressure: (psig) Design press.: (psig)
42 Liquid: Hazardous Flammable pH Min. return press. (psig) Max. allow. D.P. (psi)
43 Other: Chloride concentration: (ppm)
44 Fluid Rating System: NFPA 704 HMIS General Remarks
45 Health: Flammability: Instability:
46 Corrosion / erosion caused by:
47 % solids: % Volume % Weight
48 Max. particle size: (in)
49 Other:
50 Number Date Data Revision Description By Approved
51
52
53
 Centrifugal Pump Data Sheet Issue Date
Rev No.:_________ Rev Date:_____________________ November 2019

ASME B73 ASME Centrifugal Pumps (US Customary Units) Page 2 of 4

ASME B73.1, ASME B73.2
Usage key - data provided by: Purchaser Supplier Supplier if not by purchaser
1 Mechanical Data Driver
2 Impeller Type: Power rating: (HP) Speed: (rpm)
3 Closed Open Semi-open Drive HP selected for max. S.G. & max. visc.: (cP)
4 Casing Mounting: Driver specification:
5 Foot Centerline Vertical Driver manufacturer:
6 Bearings: Driver enclosure: Driver frame:
7 Bearing manufacturer: Remarks:
8 Radial bearing type: No.:
9 Thrust bearing type: No.: Baseplate
10 Bearing isolators: Labyrinth (standard) Magnetic seal Type: Grouted
11 Manufacturer: Concrete filled (non-metallic pedestal baseplate)
12 Lubrication: Free standing Pump CL to foundation (in)
13 Oil bath Pure mist Shielded (grease) Vertical in-line pump case support bracket
14 Grease Purge mist Sealed (grease) Design: Purchaser specification
15 Magnetic drain plug in housing Oil cooler ASME B73 standard
16 Oil viscosity: ISO grade: Other: Industrial duty grouted fabricated steel
17 Nozzle Connections: Size Rating Facing Non-metallic
18 Suction: Cast iron
19 Discharge: Remarks:
20 Aux. case connection: Drain
21 Size: NPT / NPS Paint, Shipment, and Storage Preparation
22 Threaded Welded and flanged Paint:
23 MATERIALS Pump supplier's standard
24 Material class code: Other:
25 Casing: Shipment:
26 Impeller: Domestic Export Export boxing
27 Cover: Storage:
28 Shaft: Outside Under roof Environmentally controlled
29 Shaft sleeve: Short term Long term (>3 months)
30 Baseplate: Environment:
31 Casing gasket: Supplier's standard preservation specification
32 Impeller o-ring / gasket: Purchaser storage specification:
33 Casing fasteners: Unit shipping weight: (lbs)
34 Gland fasteners: Tests and Inspections
35 Bearing housing: Test: Non-witnessed Witnessed Certificate
36 Bearing housing adapter: Hydrostatic:
37 Bearing isolators: Leak:
38 Coupling guard: NPSHR:
39 Mechanical seal materials - see page 3 Performance:
40 Coupling Between Pump and Driver Opt perf acceptance criteria: Power Efficiency Neither
41 Specification: Additonal data: Vibration Brg temp
42 Manufacturer: Other perf. data:
43 Type: Final inspection Days notification required:
44 Model / Size: Dismantle and inspect after test
45 Spacer length: (in) Casting repair procedure approval required
46 Coupling balanced to ISO 21940-11, grade G6.3 Statement of Compliance
47 Straight bore hub with interference fit Certified Mill Test Reports:
48 Coupling guard type: Casing Cover Impeller Shaft
49 Pump supplier's standard ASME B73 Guard Other:
50 Purchaser Specification: Inspection required for connection welds and castings:
51 Non-spark coupling guard Manufacturer's standard Level 1 Level 2 Level 3
52 Remarks: Other:
53 Remarks:
54

55
56
 Centrifugal Pump Data Sheet Issue Date
Rev No.:_________ Rev Date:_____________________ November 2019

ASME B73 ASME Centrifugal Pumps (US Customary Units) Page 3 of 4

ASME B73.1, ASME B73.2
Usage key - data provided by: Purchaser Supplier Supplier if not purchaser
1 Shaft Sealing Mechanical seal Packing Flush Plan - Single or Inner Seal
2 Furnished by Supplier Purchaser Piping plan number(s):
3 Installed by Supplier Purchaser External flush fluid
4 Seal Chamber Taper bore Large cylindrical bore Supply temperature Min Max (°F)
5 Universal cover Packing box Specific gravity Specific heat (Btu/lb °F)
6 Throat bushing None Fixed bushing Vapor pressure psia @ (°F)
7 Floating bushing Flow rate required Min Max (gpm)
8 Throat bushing material Maximum flow rate allowed by process (gpm)
9 Jacketed seal chamber/packing box Yes No Pressure required Min Max (psig)
10 For Heating Cooling Maximum pressure allowed by process (psig)
11 Remarks Temperature required Min Max (°F)
12 Inner seal flush plan piping Tube Pipe
13 Mechanical Seal Cartridge Component Other
14 (ref. Annex ii) Arrangement 1 (single seal) Tube/pipe size
15 Arrangement 2 (dual unpressurized seal) Tube/pipe material 316 SS Other
16 Arrangement 3 (dual pressurized seal) Tube/pipe specification
17 Flexible element Rotating Stationary Tube/pipe connections Threaded Socket weld
18 B73.1 or B73.2 Mand. App. II configuration code: Unions Butt weld Tube fitting
19 API 682 Category 1 Yes No Other
20 Manufacturer Furnished by Supplier Purchaser
21 Model Remarks
22 Manufacturer code
23 Drawing number Flush Plan - Outer Seal
24 Remarks Piping plan number(s):
25 External flush fluid
26 Seal Materials - Single or Inner Seal Supply temperature Min Max (°F)
27 Seal faces Rotating face Specific gravity Specific heat (Btu/lb °F)
28 Stationary face Vapor pressure psia @ (°F)
29 Secondary seals Rotating face Flow rate required Min Max (gpm)
30 Stationary face Maximum flow rate allowed by process (gpm)
31 Sleeve Pressure required Min Max (psig)
32 Springs Bellows Maximum pressure allowed by process (psig)
33 Metal parts Temperature required Min Max (°F)
34 Remarks MAWP Flush plan psig @ min temp (°F)
35 psig @ max temp (°F)
36 Seal Materials - Outer Seal Outer seal flush plan piping Tube Pipe
37 Seal faces Rotating face Other
38 Stationary face Tube/pipe size
39 Secondary seals Rotating face Tube/pipe material 316 SS Other
40 Stationary face Tube/pipe specification
41 Sleeve Tube/pipe connections Threaded Socket weld
42 Springs Bellows Unions Butt weld Tube fitting
43 Metal parts Other
44 Remarks Furnished by Supplier Purchaser
45 Remarks
46 Seal Gland Material
47 Ports Flush Drain Vent Quench Quench Yes No
48 Buffer/barrier fluid inlet Buffer/barrier fluid outlet Quench fluid
49 Throttle bushing Yes No Flow rate
50 Throttle bushing material Remarks
51 Remarks
 Centrifugal Pump Data Sheet Issue Date
Rev No.:_________ Rev Date:_____________________ November 2019

ASME B73 ASME Centrifugal Pumps (US Customary Units) Page 4 of 4

ASME B73.1, ASME B73.2
Usage key - data provided by Purchaser Supplier Supplier if not purchaser
1 Auxiliary Equipment Heating and Cooling
2 Reservoir Yes No Heating required Cooling required
3 Furnished by Supplier Purchaser Piping plan designation:
4 Drawing number Piping plan furnished by Supplier Purchaser
5 Material 316 SS Other Fluid
6 Operating pressure (psig) Temperature Inlet Outlet (°F)
7 Operating temperature (°F) Maximum allowable differential temperature (°F)
8 MAWP of reservoir psig @ min temp (°F) Rated flow rate (gpm)
9 psig @ max temp (°F) Supply pressure (psig)
10 Code specification Type Tube Pipe Other
11 Code stamped Yes No Tube/pipe size
12 Size 3 gallon 5 gallon Other Tube/pipe material 316 SS Galvanized carbon steel
13 Internal cooling coils Yes No Other
14 Stand required Yes No Tube/pipe specification
15 Baseplate mounted Yes No Tube/pipe connections Threaded Socket weld
16 Seal cooler Yes No Unions Butt weld Tube fittings
17 Water cooled Air cooled Other
18 Manufacturer Remarks
19 Model
20 API 682 design Yes No
21 Spray guard Yes No Manufacturer Documentation Required
22 Remarks: For supplier data requirements refer to:
23 Remarks:
24
25 Instrumentation
26 Inner seal Indicator Switch Transmitter
27 Flow rate
28 Temperature
29 Pressure Remarks
30 Remarks
31 Outer seal Indicator Switch Transmitter
32 Flow rate
33 Temperature
34 Pressure
35 Level
36 Remarks
37 Heating or cooling Indicator Switch Transmitter
38 Flow rate
39 Temperature
40 Remarks
41
42 Packing
43 Packing code (P1 - P4) Number of Rings
44 Material
45 Manufacturer
46 Manufacturer style number
47 Packing Construction
48 Sleeve hard surfacing Yes No
49 Lantern ring Yes No
50 Lantern ring port Yes No
51 Remarks