Scribd
Upload
33 views

LSIS VFD Firmware Flash Procedure: Purpose

This document provides steps to flash new firmware onto an LSIS iS7 variable frequency drive (VFD) using a Smart Copier device. The procedure involves downloading the firmware file from LSIS, copying it to an SD card for the Smart Copier, connecting the Smart Copier to the VFD, initiating the flash from the Smart Copier, and then setting the VFD's kW capacity after the flash is complete. Following these steps ensures the VFD is updated with the latest or custom application-specific firmware.

Uploaded by

Engr.Zahedul Hoque
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
33 views

LSIS VFD Firmware Flash Procedure: Purpose

This document provides steps to flash new firmware onto an LSIS iS7 variable frequency drive (VFD) using a Smart Copier device. The procedure involves downloading the firmware file from LSIS, copying it to an SD card for the Smart Copier, connecting the Smart Copier to the VFD, initiating the flash from the Smart Copier, and then setting the VFD's kW capacity after the flash is complete. Following these steps ensures the VFD is updated with the latest or custom application-specific firmware.

Uploaded by

Engr.Zahedul Hoque
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

LSIS VFD Firmware Flash Procedure

iS7

Purpose
This document provides the step by step procedure for flashing firmware on an LSIS iS7 VFD using the Smart Copier.
This procedure should be followed whenever an application demands custom application specific firmware or an update to
the latest factory firmware.

For questions or assistance with this procedure please contact LSIS Technical Support.
Phone: 800-891-2941 Email: [email protected]

1. Necessary Items
 Smart Copier (the below items are included with purchase) LSIS Order Code: 64090112
o 4 qty AA Batteries
o SD Card
 Smart Copier Gender (order both this and the Smart Copier!) LSIS Order Code: 64090124
o 10-pin cable
o Gender Connectors for S100, H100, and iS7
No file extension
 Computer with SD card slot
 Flash File
 LSIS iS7 VFD

2. Preparing the Firmware File


a. Request the needed firmware file from LSIS
Technical Support.
.scf file type is
b. The Smart Copier uses a .scf file
necessary for the
type though the .scf is not listed in
Smart Copier
Windows explorer. Verify the
correct file type by right-clicking the file and
selecting “properties.” The file type .scf is listed.
See Figure 1.
c. Insert the SD card which came with the smart
copier into the PC.
d. Create a new folder on the SC card titles
“firmwares”.
e. Drag and Drop or Copy/Paste the firmware file
into the “firmwares” folder on the SD Card.
f. Remove the SD Card from the PC and insert into
the SD card slot on the right side of the Smart
Copier. See Figure 2.

Figure 1

Figure 2
1

LSIS iS7 Firmware Flash Procedure


Rev A_12-13-2016
LSIS VFD Firmware Flash Procedure
iS7

3. Connecting to the VFD


a. Install the provided AA batteries into the battery compartment on the back of the Smart Copier.
b. Connect the 10-pin ribbon cable to the top of the Smart Copier
c. Connect the other end of the ribbon cable to the correct “iS7 Main” Gender for the VFD which is being
flashed.
d. The connection setup should look like Figure 3.

10-pin
Gender ribbon cable

Smart
Copier

Figure 3
e. Power down the VFD. The VFD must be powered down when flashing the firmware.
f. Slide the Gender housing back to expose the pins which will be connected to the drives flash port. See
Figure 4.

Plastic housing
slides back

exposing pins for


flashing.

Figure 4

LSIS iS7 Firmware Flash Procedure


Rev A_12-13-2016
LSIS VFD Firmware Flash Procedure
iS7

g. Gain access to the flash port by removing the keypad and the front cover. See Figure 5.

Figure 5

LSIS iS7 Firmware Flash Procedure


Rev A_12-13-2016
LSIS VFD Firmware Flash Procedure
iS7

h. Connect the “iS7 Main” Gender to the VFD flash port. Take note that the Gender connection direction
and placement must be correct. This is printed on the Gender board and also explained in Figure 6
below. The GND pin should be on the bottom and all 7 pins should be plugged in to the right side of the
flash port.

Left
portion of
flash port
is not
used

Ground
pin is
DOWN

Figure 6

4. Flashing the VFD


a. Power on the Smart Copier with the ON/OFF switch located on the left side of the Smart Copier.
b. At power up the screen will display “MAIN Board Firmware Download” (flashing).
c. Press the ENTER key to view the available firmware files.
d. Use the UP and DOWN arrows to highlight the firmware file which was copied to the SD Card in Section
2.
e. Press the ENTER key once to select the file and then ENTER again to start the flashing process.
f. The flashing process will take about 1 minute to complete. Upon completion the Smart Copier will flash
“100% Success.”
Note: If the status % bar freezes up and then fails, check the direction of the Gender and confirm it
matches the direction discussed earlier.
g. Power off the Smart Copier, disconnect the Gender, and reassemble the drive.
h. CNF10 can be used to verify the proper Firmware version.

LSIS iS7 Firmware Flash Procedure


Rev A_12-13-2016
LSIS VFD Firmware Flash Procedure
iS7

5. Setting the VFDs kW


After flashing an iS7 VFD the kW capacity must be set. Follow the below steps.
a. Hold the ESC button
b. While holding the ESC button…
1. press the UP button
2. then the DOWN button
Hol 3
3. then the PROG/ENT button 1
d

c. After this is done properly the Master Password screen


will appear. Set this to A57C.
2

d. Press MODE to get into the Parameter Group.


e. Press the Left arrow to display the MAK Group. (If you cannot see the MAK Group then the code was
entered incorrectly).

f. In the MAK Group enter the correct drive Capacity (kW) and Voltage in MAK01 (use the VFDs nameplate
to verify the drive kW size first, use the HD kW rating). i.e. 0.75kW-2 = 75kW, 230V

g. Complete.

LSIS iS7 Firmware Flash Procedure


Rev A_12-13-2016

You might also like