LED Driver

OUTDOOR Linear IP67 fixed output

Driver LCO 100W 500/700/1050/1400mA fixC L SNC2

essence outdoor series

Product description
• Independent fixed output LED Driver
• Constant current LED Driver
• Output current 500, 700, 1,050 or 1,400 mA
• Up to 92 % efficiency
• Ambient temperature range of -40 ... +60 °C
• Max. casing temperature tc of 90 °C
• Nominal life-time up to 100,000 h
• 5-year guarantee (conditions at www.tridonic.com)

Properties
• Casing: metal, black
• Type of protection IP67

Interfaces
• Connection: cable 300 mm

Functions
• Protective features (overtemperature, short-circuit, overload,
no-load)

Benefits
• Wide voltage input 100 – 240 V
• Best energy savings due to low stand-by losses and
high efficiency
• Suitable for mains voltage peaks (burst/surge) up to 6 kV
• Double or reinforced insulation
• High number of drivers on 16 A (B) automatic circuit breakers
• Extended vibration damping
• The LED Driver is designed for a life-time stated above under
reference conditions and with a failure probability of less than
10 %
• The wide product range offers common currents for a cost
effective luminaire manufacturing

Typical applications
• For parking lot, high bay, street and road applications
• For linear/area lighting in industry applications

È
Standards, page 3
Wiring diagrams and installation examples, page 3

Data sheet 11/21-LC641-11

Subject to change without notice. Information provided without guarantee. www.tridonic.com 1
 LED Driver
OUTDOOR Linear IP67 fixed output

Only for 500 and 700 mA: Driver LCO 100W 500/700/1050/1400mA fixC L SNC2
essence outdoor series

Technical data
Rated supply voltage 120 – 240 V 181
AC voltage range 100 – 240 V 165

29,1
Mains frequency 50 / 60 Hz 151

29
8
5
Leakage current (at 230 V, 50 Hz, full load) < 500 µA 30
30 tc
THD (at 230 V, 50 Hz, full load) < 10 %

45

5
Output current tolerance2 ±5% 8,1

8
Starting time (at 230 V, 50 Hz, full load) ≤ 0.5 s 36,8 61
Turn off time (at 230 V, 50 Hz, full load) ≤ 0.5 s 305 305 10
10

37,8
Ambient temperature ta -40 ... +60 °C
Storage temperature ts -40 ... +85 °C
Mains burst capability 4 kV
Mains surge capability (between L – N) 4 kV Ordering data
Mains surge capability (between L/N – PE) 6 kV Article Packaging, Packaging, Weight
Type
number5 carton pallet per pc.
Surge voltage at output side (against PE) 2 kV
LCO 100/500/200 fixC L SNC2 28002301 10 pc(s). 420 pc(s). 0.61 kg
Life-time up to 100,000 h
LCO 100/700/143 fixC L SNC2 28002302 10 pc(s). 420 pc(s). 0.61 kg
Guarantee (conditions at www.tridonic.com) 5 years
LCO 100/1050/95 fixC L SNC2 28002303 10 pc(s). 420 pc(s). 0.61 kg
Dimensions L x W x H 181 x 61 x 37.8 mm
LCO 100/1400/71 fixC L SNC2 28002304 10 pc(s). 420 pc(s). 0.61 kg

Specific technical data

Type Output Input current Input power Max. Output λ Efficiency λ Efficiency Min. Max. Max. output Max. peak Typ. output Max. casing
current2 (at 230 V, (at 230 V, input power at full at full at min. at min. forward forward voltage output LF current tempera-
50 Hz, full 50 Hz, full power range load1 load1 load1 load1 voltage voltage (U-OUT) current at ripple at ture tc
load) load) full load3 full load4
LCO 100/500/200 fixC L SNC2 500 mA 480 mA 110.9 W 110.9 W 30 – 100 W 0.98 90.0 % 0.90C 81.5 % 60 V 200 V 210 V 600 mA <7% 90 °C
LCO 100/700/143 fixC L SNC2 700 mA 480 mA 108.9 W 108.9 W 30 – 100 W 0.96 91.5 % 0.86C 80.5 % 43 V 143 V 153 V 819 mA <5% 90 °C
LCO 100/1050/95 fixC L SNC2 1,050 mA 490 mA 109.7 W 109.7 W 30 – 100 W 0.98 91.5 % 0.89C 78.5 % 29 V 95 V 101 V 1,481 mA < 15 % 90 °C
LCO 100/1400/71 fixC L SNC2 1,400 mA 480 mA 108.2 W 108.2 W 30 – 100 W 0.98 92.0 % 0.86C 78.5 % 21 V 71 V 77 V 1,694 mA <2% 90 °C
1
Test result at 230 V, 50 Hz
2
Output current is mean value.
3
The trend between min. and full load is linear and depends on load‘s voltage-current character.
4
Typical value at full load, depends on load‘s voltage-current character.
5
The delivery time is 13 weeks, except 28002303.

Data sheet 11/21-LC641-11

Subject to change without notice. Information provided without guarantee. www.tridonic.com 2
 LED Driver
OUTDOOR Linear IP67 fixed output

1. Standards

EN 55015
EN 61000-3-2
EN 61000-3-3
EN 61347-1
EN 61347-2-13
EN 61547
EN 62384

2. Thermal details and life-time

2.1 Expected life-time

Expected life-time
Type ta 50 °C 55 °C 60 °C
tc 65 °C 70 °C 75 °C
LCO 100/500/200 fixC L SNC2
Life-time >100,000  h 90,000  h 60,000 h
tc 65 °C 70 °C 75 °C
LCO 100/700/143 fixC L SNC2
Life-time >100,000  h 100,000  h 70,000 h
tc 65 °C 70 °C 75 °C
LCO 100/1050/95 fixC L SNC2
Life-time >100,000  h 95,000  h 65,000 h
tc 65 °C 70 °C 75 °C
LCO 100/1400/71 fixC L SNC2
Life-time >100,000  h 100,000  h 70,000 h

The LED Driver is designed for a lifetime stated above under reference
conditions and with a failure probability of less than 10 %.

The relation of tc to ta temperature depends also on the luminaire design.

If the measured tc temperature is approx. 5 K below tc max., ta temperature
should be checked and eventually critical
components (e.g. ELCAP) measured. Detailed information on request.

3. Installation / wiring

3.1 Circuit diagram

120–240 V
50/60 Hz
L
N
PRI


+ LED PE
SEC

– LED


3.2 Connection

Primary Secondary
cable cable
L N PE + –
brown blue green/yellow brown blue

305
10

PRI:
3x 1.0 mm2

SEC:
2 x 1.0 mm2

Data sheet 11/21-LC641-11

Subject to change without notice. Information provided without guarantee. www.tridonic.com 3
 LED Driver
OUTDOOR Linear IP67 fixed output

3.3 Wiring instructions 4. Electrical values

• All connections must be kept as short as possible to ensure good EMI 4.1 Diagrams
behaviour
• To comply with the EMC regulations run the secondary wires 4.1.1 Efficiency vs Load
(LED module) in parallel.
• Mains leads should be kept apart from LED Driver and other leads
92,5
(ideally 5 – 10 cm distance)
• The maximum length of output wires is 3 m.
• Secondary switching is not permitted. 90,0
• Incorrect wiring can damage LED modules.
• To avoid the damage of the Driver, the wiring must be protected against 87,5

Efficency [%]
short circuits to earth (sharp edged metal parts, metal cable clips, louver,
etc.). 85,0

82,5
3.4 Installation instructions
80,0
The switching of LEDs on secondary side is not permitted.
77,5
30 40 50 60 70 80 90 100
3.5 Fixing conditions Load [%]

Acidfree, oilfree, fatfree. It is not allowed to exceed the maximum ambient

temperature (ta) stated on the device. Minimum distances stated below are 4.1.2 Power factor vs Load
recommendations and depend on the actual luminaire. Is not suitable for
fixing in corner. Terminals according to EN 60998-2-1 or EN 60998-2-2 are 1,00
required.

0,95
>20 mm

Power factor

Leuchte
Luminaire >100 mm >20 mm

0,90

3.6 Earth connection 0,85

30 40 50 60 70 80 90 100
The earth connection is conducted as protection earth (PE). The LED Driver
can be earthed via metal housing. If the LED Driver will be earthed, Load [%]
protection earth (PE) has to be used. There is no earth connection required
for the functionality of the LED Driver. Earth connection is recommended to
improve following behaviour. 4.1.3 THD vs Load

• Electromagnetic interferences (EMI) 25

• Transmission of mains transients to the LED output
20
In general it is recommended to earth the LED Driver if the LED module is
mounted on earthed luminaire parts respectively heat sinks and thereby
representing a high capacity against earth. 15
THD

10

0
30 40 50 60 70 80 90 100
Load [%]

Data sheet 11/21-LC641-11

Subject to change without notice. Information provided without guarantee. www.tridonic.com 4
 LED Driver
OUTDOOR Linear IP67 fixed output

4.2 Maximum loading of automatic circuit breakers in relation to inrush current

Automatic circuit C10 C13 C16 C20 B10 B13 B16 B20 Inrush current
breaker type
Installation Ø 1.5 mm2 1.5 mm2 1.5 mm2 2.5 mm2 1.5 mm2 1.5 mm2 1.5 mm2 2.5 mm2 Imax Time
LCO 100/500/200 fixC L SNC2 7 9 10 14 3 5 7 10 103 A 167 µs
LCO 100/700/143 fixC L SNC2 7 9 10 14 3 5 7 10 103 A 167 µs
LCO 100/1050/95 fixC L SNC2 7 9 10 14 3 5 7 10 103 A 167 µs
LCO 100/1400/71 fixC L SNC2 7 9 10 14 3 5 7 10 103 A 167 µs

This are max. values calculated out of inrush current! Please consider not to exceed the maximum rated continuous current of the circuit breaker.
Calculation uses typical values from ABB series S200 as a reference.
Actual values may differ due to used circuit breaker types and installation environment.

4.3 Harmonic distortion in the mains supply (at 230 V / 50 Hz and full load)
in %
THD 3. 5. 7. 9. 11.
LCO 100/500/200 fixC L SNC2 <9 <5 <5 <5 <3 <2
LCO 100/700/143 fixC L SNC2 <9 <5 <5 <5 <3 <2
LCO 100/1050/95 fixC L SNC2 <9 <5 <5 <5 <3 <2
LCO 100/1400/71 fixC L SNC2 <9 <5 <5 <5 <3 <2

Acc. to 6100-3-2. Harmonics < 5 mA or < 0.6 % (whatever is greater) of the input current are
not considered for calculation of THD.

5. Functions 6. Miscellaneous

5.1 Short-circuit behaviour 6.1 Insulation and electric strength testing of luminaires

In case of a short circuit on the secondary side (LED) the LED Driver switches Electronic devices can be damaged by high voltage. This has to be considered
into hic-cup mode. After the removal of the short-circuit fault the LED Driver will during the routine testing of the luminaires in production.
recover automatically.
According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A,
5.2 No-load operation each luminaire should be submitted to an insulation test with 500 V DC for
1 second. This test voltage should be connected between the interconnected
The LED Driver works in constant voltage mode. In no-load operation the phase and neutral terminals and the earth terminal.
output voltage will not exceed the specified max. output voltage (see page 2). The insulation resistance must be at least 2 MΩ.

As an alternative, IEC 60598-1 Annex Q describes a test of the electrical

5.3 Overload protection strength with 1500 V AC (or 1.414 x 1500 V DC). To avoid damage to the electronic
devices this test must not be conducted.
If the maximum load is exceeded by a defined internal limit, the LED Driver
will work in hic-cup mode. After elimination of the overload, the nominal
6.2 Conditions of use and storage
operation is restored automatically.
Humidity: 5 % up to max. 95 %,
5.4 Overtemperature protection not condensed
(max. 56 days/year at 95 %)
The LED Driver is protected against temporary thermal overheating.
If the temperature limit is exceeded the LED Driver is switched off. Storage temperature: -40 °C up to max. +85 °C
It restarts automatically.
The devices have to be within the specified temperature range (ta) before
they can be operated.

6.3 Maximum number of switching cycles

All LED Driver are tested with 50,000 switching cycles.

6.4 Additional information

Additional technical information at www.tridonic.com → Technical Data

Lifetime declarations are informative and represent no warranty claim.

No warranty if device was opened.

Data sheet 11/21-LC641-11

Subject to change without notice. Information provided without guarantee. www.tridonic.com 5